Two bugs exist in the code related to reset_task
in PF driver one is the missing protection
against network stack ndo_open and ndo_close.
Other one is the missing cancel_work.
This patch fixes those problems.

Fixes: 4ff7d148

 ("octeontx2-pf: Error handling support")
Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

It appears that not disabling a PCI device on .shutdown may lead to
a Hardware Error with particular (perhaps buggy) BIOS versions:

    mlx4_en: eth0: Close port called
    mlx4_en 0000:04:00.0: removed PHC
    reboot: Restarting system
    {1}[Hardware Error]: Hardware error from APEI Generic Hardware Error Source: 1
    {1}[Hardware Error]: event severity: fatal
    {1}[Hardware Error]:  Error 0, type: fatal
    {1}[Hardware Error]:   section_type: PCIe error
    {1}[Hardware Error]:   port_type: 4, root port
    {1}[Hardware Error]:   version: 1.16
    {1}[Hardware Error]:   command: 0x4010, status: 0x0143
    {1}[Hardware Error]:   device_id: 0000:00:02.2
    {1}[Hardware Error]:   slot: 0
    {1}[Hardware Error]:   secondary_bus: 0x04
    {1}[Hardware Error]:   vendor_id: 0x8086, device_id: 0x2f06
    {1}[Hardware Error]:   class_code: 000604
    {1}[Hardware Error]:   bridge: secondary_status: 0x2000, control: 0x0003
    {1}[Hardware Error]:   aer_uncor_status: 0x00100000, aer_uncor_mask: 0x00000000
    {1}[Hardware Error]:   aer_uncor_severity: 0x00062030
    {1}[Hardware Error]:   TLP Header: 40000018 040000ff 791f4080 00000000
[hw error repeats]
    Kernel panic - not syncing: Fatal hardware error!
    CPU: 0 PID: 2189 Comm: reboot Kdump: loaded Not tainted 5.6.x-blabla #1
    Hardware name: HP ProLiant DL380 Gen9/ProLiant DL380 Gen9, BIOS P89 05/05/2017

Fix the mlx4 driver.

This is a very similar problem to what had been fixed in:
commit 0d98ba8d ("scsi: hpsa: disable device during shutdown")
to address https://bugzilla.kernel.org/show_bug.cgi?id=199779.

Fixes: 2ba5fbd6

 ("net/mlx4_core: Handle AER flow properly")
Reported-by: Jake Lawrence <lawja@fb.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Herbert Xu says:

====================
rhashtable: Fix unprotected RCU dereference in __rht_ptr

This patch series fixes an unprotected dereference in __rht_ptr.
The first patch is a minimal fix that does not use the correct
RCU markings but is suitable for backport, and the second patch
cleans up the RCU markings.
====================

Signed-off-by: David S. Miller <davem@davemloft.net>

This patch restores the RCU marking on bucket_table->buckets as
it really does need RCU protection.  Its removal had led to a fatal
bug.

Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>

The rcu_dereference call in rht_ptr_rcu is completely bogus because
we've already dereferenced the value in __rht_ptr and operated on it.
This causes potential double readings which could be fatal.  The RCU
dereference must occur prior to the comparison in __rht_ptr.

This patch changes the order of RCU dereference so that it is done
first and the result is then fed to __rht_ptr.  The RCU marking
changes have been minimised using casts which will be removed in
a follow-up patch.

Fixes: ba6306e3

 ("rhashtable: Remove RCU marking from...")
Reported-by: "Gong, Sishuai" <sishuai@purdue.edu>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>

Modify mtk_gmac0_rgmii_adjust() so it can always be called.
mtk_gmac0_rgmii_adjust() sets-up the TRGMII clocks.

Signed-off-by: René van Dorst <opensource@vdorst.com>
Signed-off-By: David Woodhouse <dwmw2@infradead.org>
Tested-by: Frank Wunderlich <frank-w@public-files.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

Saeed Mahameed says:

====================
mlx5 fixes-2020-07-28

This series introduces some fixes to mlx5 driver.
v1->v2:
 - Drop the "Hold reference on mirred devices" patch, until Or's
   comments are addressed.
 - Imporve "Modify uplink state" patch commit message per Or's request.

Please pull and let me know if there is any problem.

For -Stable:

For -stable v4.9
 ('net/mlx5e: Fix error path of device attach')

For -stable v4.15
 ('net/mlx5: Verify Hardware supports requested ptp function on a given
pin')

For -stable v5.3
 ('net/mlx5e: Modify uplink state on interface up/down')

For -stable v5.4
 ('net/mlx5e: Fix kernel crash when setting vf VLANID on a VF dev')
 ('net/mlx5: E-switch, Destroy TSAR when fail to enable the mode')

For -stable v5.5
 ('net/mlx5: E-switch, Destroy TSAR after reload interface')

For -stable v5.7
 ('net/mlx5: Fix a bug of using ptp channel index as pin index')
====================

Acked-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Johan Hovold says:

====================
net: lan78xx: fix NULL deref and memory leak

The first two patches fix a NULL-pointer dereference at probe that can
be triggered by a malicious device and a small transfer-buffer memory
leak, respectively.

For another subsystem I would have marked them:

	Cc: stable@vger.kernel.org	# 4.3

The third one replaces the driver's current broken endpoint lookup
helper, which could end up accepting incomplete interfaces and whose
results weren't even useeren
Johan
====================

Signed-off-by: David S. Miller <davem@davemloft.net>

Drop the bogus endpoint-lookup helper which could end up accepting
interfaces based on endpoints belonging to unrelated altsettings.

Note that the returned bulk pipes and interrupt endpoint descriptor
were never actually used. Instead the bulk-endpoint numbers are
hardcoded to 1 and 2 (matching the specification), while the interrupt-
endpoint descriptor was assumed to be the third descriptor created by
USB core.

Try to bring some order to this by dropping the bogus lookup helper and
adding the missing endpoint sanity checks while keeping the interrupt-
descriptor assumption for now.

Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

The interrupt URB transfer-buffer was never freed on disconnect or after
probe errors.

Fixes: 55d7de9d

 ("Microchip's LAN7800 family USB 2/3 to 10/100/1000 Ethernet device driver")
Cc: Woojung.Huh@microchip.com <Woojung.Huh@microchip.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add the missing endpoint sanity check to prevent a NULL-pointer
dereference should a malicious device lack the expected endpoints.

Note that the driver has a broken endpoint-lookup helper,
lan78xx_get_endpoints(), which can end up accepting interfaces in an
altsetting without endpoints as long as *some* altsetting has a bulk-in
and a bulk-out endpoint.

Fixes: 55d7de9d

 ("Microchip's LAN7800 family USB 2/3 to 10/100/1000 Ethernet device driver")
Cc: Woojung.Huh@microchip.com <Woojung.Huh@microchip.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

in case of an error tty_register_device_attr() returns ERR_PTR(),
add IS_ERR() check

Reported-and-tested-by:  <syzbot+67b2bd0e34f952d0321e@syzkaller.appspotmail.com>
Link: https://syzkaller.appspot.com/bug?extid=67b2bd0e34f952d0321e


Signed-off-by: Rustam Kovhaev <rkovhaev@gmail.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

After the cited commit, function 'mlx5_eswitch_set_vport_vlan' started
to acquire esw->state_lock.
However, esw is not defined for VF devices, hence attempting to set vf
VLANID on a VF dev will cause a kernel panic.

Fix it by moving up the (redundant) esw validation from function
'__mlx5_eswitch_set_vport_vlan' since the rest of the callers now have
and use a valid esw.

For example with vf device eth4:
 # ip link set dev eth4 vf 0 vlan 0

Trace of the panic:
 [  411.409842] BUG: unable to handle page fault for address: 00000000000011b8
 [  411.449745] #PF: supervisor read access in kernel mode
 [  411.452348] #PF: error_code(0x0000) - not-present page
 [  411.454938] PGD 80000004189c9067 P4D 80000004189c9067 PUD 41899a067 PMD 0
 [  411.458382] Oops: 0000 [#1] SMP PTI
 [  411.460268] CPU: 4 PID: 5711 Comm: ip Not tainted 5.8.0-rc4_for_upstream_min_debug_2020_07_08_22_04 #1
 [  411.462447] Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS rel-1.12.1-0-ga5cab58e9a3f-prebuilt.qemu.org 04/01/2014
 [  411.464158] RIP: 0010:__mutex_lock+0x4e/0x940
 [  411.464928] Code: fd 41 54 49 89 f4 41 52 53 89 d3 48 83 ec 70 44 8b 1d ee 03 b0 01 65 48 8b 04 25 28 00 00 00 48 89 45 c8 31 c0 45 85 db 75 0a <48> 3b 7f 60 0f 85 7e 05 00 00 49 8d 45 68 41 56 41 b8 01 00 00 00
 [  411.467678] RSP: 0018:ffff88841fcd74b0 EFLAGS: 00010246
 [  411.468562] RAX: 0000000000000000 RBX: 0000000000000000 RCX: 0000000000000000
 [  411.469715] RDX: 0000000000000000 RSI: 0000000000000002 RDI: 0000000000001158
 [  411.470812] RBP: ffff88841fcd7550 R08: ffffffffa00fa1ce R09: 0000000000000000
 [  411.471835] R10: ffff88841fcd7570 R11: 0000000000000000 R12: 0000000000000002
 [  411.472862] R13: 0000000000001158 R14: ffffffffa00fa1ce R15: 0000000000000000
 [  411.474004] FS:  00007faee7ca6b80(0000) GS:ffff88846fc00000(0000) knlGS:0000000000000000
 [  411.475237] CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
 [  411.476129] CR2: 00000000000011b8 CR3: 000000041909c006 CR4: 0000000000360ea0
 [  411.477260] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
 [  411.478340] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
 [  411.479332] Call Trace:
 [  411.479760]  ? __nla_validate_parse.part.6+0x57/0x8f0
 [  411.482825]  ? mlx5_eswitch_set_vport_vlan+0x3e/0xa0 [mlx5_core]
 [  411.483804]  mlx5_eswitch_set_vport_vlan+0x3e/0xa0 [mlx5_core]
 [  411.484733]  mlx5e_set_vf_vlan+0x41/0x50 [mlx5_core]
 [  411.485545]  do_setlink+0x613/0x1000
 [  411.486165]  __rtnl_newlink+0x53d/0x8c0
 [  411.486791]  ? mark_held_locks+0x49/0x70
 [  411.487429]  ? __lock_acquire+0x8fe/0x1eb0
 [  411.488085]  ? rcu_read_lock_sched_held+0x52/0x60
 [  411.488998]  ? kmem_cache_alloc_trace+0x16d/0x2d0
 [  411.489759]  rtnl_newlink+0x47/0x70
 [  411.490357]  rtnetlink_rcv_msg+0x24e/0x450
 [  411.490978]  ? netlink_deliver_tap+0x92/0x3d0
 [  411.491631]  ? validate_linkmsg+0x330/0x330
 [  411.492262]  netlink_rcv_skb+0x47/0x110
 [  411.492852]  netlink_unicast+0x1ac/0x270
 [  411.493551]  netlink_sendmsg+0x336/0x450
 [  411.494209]  sock_sendmsg+0x30/0x40
 [  411.494779]  ____sys_sendmsg+0x1dd/0x1f0
 [  411.495378]  ? copy_msghdr_from_user+0x5c/0x90
 [  411.496082]  ___sys_sendmsg+0x87/0xd0
 [  411.496683]  ? lock_acquire+0xb9/0x3a0
 [  411.497322]  ? lru_cache_add+0x5/0x170
 [  411.497944]  ? find_held_lock+0x2d/0x90
 [  411.498568]  ? handle_mm_fault+0xe46/0x18c0
 [  411.499205]  ? __sys_sendmsg+0x51/0x90
 [  411.499784]  __sys_sendmsg+0x51/0x90
 [  411.500341]  do_syscall_64+0x59/0x2e0
 [  411.500938]  ? asm_exc_page_fault+0x8/0x30
 [  411.501609]  ? rcu_read_lock_sched_held+0x52/0x60
 [  411.502350]  entry_SYSCALL_64_after_hwframe+0x44/0xa9
 [  411.503093] RIP: 0033:0x7faee73b85a7
 [  411.503654] Code: Bad RIP value.

Fixes: 0e18134f

 ("net/mlx5e: Eswitch, use state_lock to synchronize vlan change")
Signed-off-by: Alaa Hleihel <alaa@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Reviewed-by: Vlad Buslov <vladbu@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

When setting the PF interface up/down, notify the firmware to update
uplink state via MODIFY_VPORT_STATE, when E-Switch is enabled.

This behavior will prevent sending traffic out on uplink port when PF is
down, such as sending traffic from a VF interface which is still up.
Currently when calling mlx5e_open/close(), the driver only sends PAOS
command to notify the firmware to set the physical port state to
up/down, however, it is not sufficient. When VF is in "auto" state, it
follows the uplink state, which was not updated on mlx5e_open/close()
before this patch.

When switchdev mode is enabled and uplink representor is first enabled,
set the uplink port state value back to its FW default "AUTO".

Fixes: 63bfd399

 ("net/mlx5e: Send PAOS command on interface up/down")
Signed-off-by: Ron Diskin <rondi@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Reviewed-by: Moshe Shemesh <moshe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

In a special configuration, a ConnectX6-Dx pin pps-out might be activated
when driver is loaded. Fix the driver to always read the operational pin
mode when registering it, and advertise it accordingly.

Fixes: ee7f1220

 ("net/mlx5e: Implement 1PPS support")
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

mlx5e_rep_is_lag_netdev is used as first check as part of netdev events
handler for bond device of non-uplink representors, this handler can get
any netdevice under the same network namespace of mlx5e netdevice. Current
code treats the netdev as mlx5e netdev and only later on verifies this,
hence causes the following Kasan trace:
[15402.744990] ==================================================================
[15402.746942] BUG: KASAN: slab-out-of-bounds in mlx5e_rep_is_lag_netdev+0xcb/0xf0 [mlx5_core]
[15402.749009] Read of size 8 at addr ffff880391f3f6b0 by task ovs-vswitchd/5347

[15402.752065] CPU: 7 PID: 5347 Comm: ovs-vswitchd Kdump: loaded Tainted: G    B      O     --------- -t - 4.18.0-g3dcc204d291d-dirty #1
[15402.755349] Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS rel-1.12.1-0-ga5cab58e9a3f-prebuilt.qemu.org 04/01/2014
[15402.757600] Call Trace:
[15402.758968]  dump_stack+0x71/0xab
[15402.760427]  print_address_description+0x6a/0x270
[15402.761969]  kasan_report+0x179/0x2d0
[15402.763445]  ? mlx5e_rep_is_lag_netdev+0xcb/0xf0 [mlx5_core]
[15402.765121]  mlx5e_rep_is_lag_netdev+0xcb/0xf0 [mlx5_core]
[15402.766782]  mlx5e_rep_esw_bond_netevent+0x129/0x620 [mlx5_core]

Fix by deferring the violating access to be post the netdev verify check.

Fixes: 7e51891a

 ("net/mlx5e: Use netdev events to set/del egress acl forward-to-vport rule")
Signed-off-by: Raed Salem <raeds@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Reviewed-by: Vu Pham <vuhuong@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

Fix a bug where driver did not verify Hardware pin capabilities for
PTP functions.

Fixes: ee7f1220

 ("net/mlx5e: Implement 1PPS support")
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Reviewed-by: Ariel Levkovich <lariel@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

On PTP mlx5_ptp_enable(on=0) flow, driver mistakenly used channel index
as pin index.

After ptp patch marked in fixes tag was introduced, driver can freely
call ptp_find_pin() as part of the .enable() callback.

Fix driver mlx5_ptp_enable(on=0) flow to always use ptp_find_pin(). With
that, Driver will use the correct pin index in mlx5_ptp_enable(on=0) flow.

In addition, when initializing the pins, always set channel to zero. As
all pins can be attached to all channels, let ptp_set_pinfunc() to move
them between the channels.

For stable branches, this fix to be applied only on kernels that includes
both patches in fixes tag. Otherwise, mlx5_ptp_enable(on=0) will be stuck
on pincfg_mux.

Fixes: 62582a7e ("ptp: Avoid deadlocks in the programmable pin code.")
Fixes: ee7f1220

 ("net/mlx5e: Implement 1PPS support")
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Reviewed-by: Ariel Levkovich <lariel@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

The cited commit add initialization of ethtool steering during
representor rx initializations without cleaning it up in representor
rx cleanup, this may cause for stale ethtool flows to remain after
moving back from switchdev mode to legacy mode.

Fixed by calling ethtool steering cleanup during rep rx cleanup.

Fixes: 6783e8b2

 ("net/mlx5e: Init ethtool steering for representors")
Signed-off-by: Maor Dickman <maord@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Reviewed-by: Vlad Buslov <vladbu@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

On failure to attach the netdev, fix the rollback by re-setting the
device's state back to MLX5E_STATE_DESTROYING.

Failing to attach doesn't stop statistics polling via .ndo_get_stats64.
In this case, although the device is not attached, it falsely continues
to query the firmware for counters. Setting the device's state back to
MLX5E_STATE_DESTROYING prevents the firmware counters query.

Fixes: 26e59d80

 ("net/mlx5e: Implement mlx5e interface attach/detach callbacks")
Signed-off-by: Aya Levin <ayal@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

The steering tree is as follow (nic RX as example):
		   ---------
                   |root_ns|
		   ---------
			|
      	--------------------------------
    	|		|	       |
   ---------- 	   ----------      ---------
   |p(prio)0|	   |   p1   |      |   pn  |
   ----------	   ----------	   ---------
        |		|
 ----------------  ---------------
 |ns(e.g bypass)|  |ns(e.g. lag) |
 ----------------  ---------------
  |     |    |
----  ----  ----
|p0|  |p1|  |pn|
----  ----  ----
 |
----
|FT|
----

find_next_chained_ft(prio) returns the first flow table in the next
priority. If prio is a parent of a flow table then it returns the first
flow table in the next priority in the same namespace, else if prio
is parent of namespace, then it should return the first flow table
in the next namespace. Currently if the user requests to forward to
next namespace, the code calls to find_next_chained_ft with the prio
of the next namespace and not the prio of the namesapce itself.

Fixes: 9254f8ed

 ("net/mlx5: Add support in forward to namespace")
Signed-off-by: Maor Gottlieb <maorg@mellanox.com>
Reviewed-by: Mark Bloch <markb@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

When eswitch offloads is enabled, TSAR is created before reloading
the interfaces.
However when eswitch offloads mode is disabled, TSAR is disabled before
reloading the interfaces.

To keep the eswitch enable/disable sequence as mirror, destroy TSAR
after reloading the interfaces.

Fixes: 1bd27b11

 ("net/mlx5: Introduce E-switch QoS management")
Signed-off-by: Parav Pandit <parav@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

When either esw_legacy_enable() or esw_offloads_enable() fails,
code missed to destroy the created TSAR.

Hence, add the missing call to destroy the TSAR.

Fixes: 610090eb

 ("net/mlx5: E-switch, Initialize TSAR Qos hardware block before its user vports")
Signed-off-by: Parav Pandit <parav@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

Huazhong Tan says:

====================
net: hns3: fixes for -net

There are some bugfixes for the HNS3 ethernet driver. patch#1 fixes
a desc filling bug, patch#2 fixes a false TX timeout issue, and
patch#3~#5 fixes some bugs related to VLAN and FD.
====================

Signed-off-by: David S. Miller <davem@davemloft.net>

When device is resetting or reset failed, firmware is unable to
handle mailbox. VLAN should not be configured in this case.

Fixes: fe4144d4

 ("net: hns3: sync VLAN filter entries when kill VLAN ID failed")
Signed-off-by: Guojia Liao <liaoguojia@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When user had created a FD rule, all the aRFS rules should be clear up.
HNS3 process flow as below:
1.get spin lock of fd_ruls_list
2.clear up all aRFS rules
3.release lock
4.get spin lock of fd_ruls_list
5.creat a rules
6.release lock;

There is a short period of time between step 3 and step 4, which would
creatting some new aRFS FD rules if driver was receiving packet.
So refactor the fd_rule_lock to fix it.

Fixes: 44122887

 ("net: hns3: refine the flow director handle")
Signed-off-by: Guojia Liao <liaoguojia@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Currently hclgevf_update_port_base_vlan_info() may be called when
VF is resetting,  which may cause hns3_nic_net_open() being called
twice unexpectedly.

So fix it by adding a reset check for it, and extend critical
region for rntl_lock in hclgevf_update_port_base_vlan_info().

Fixes: 92f11ea1

 ("net: hns3: fix set port based VLAN issue for VF")
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When the queue depth and queue parameters are modified, there is
a low probability that TX timeout occurs. The two operations cause
the link to be down or up when the watchdog is still working. All
queues are stopped when the link is down. After the carrier is on,
all queues are woken up. If the watchdog detects the link between
the carrier on and wakeup queues, a false TX timeout occurs.

So fix this issue by modifying the sequence of carrier on and queue
wakeup, which is symmetrical to the link down action.

Fixes: 76ad4f0e

 ("net: hns3: Add support of HNS3 Ethernet Driver for hip08 SoC")
Signed-off-by: Yonglong Liu <liuyonglong@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The linear and frag data part may be changed when the skb is expanded
or lineared in skb_cow_head() or skb_checksum_help(), which is called
by hns3_fill_skb_desc(), so the linear len return by skb_headlen()
before the calling of hns3_fill_skb_desc() is unreliable.

Move hns3_fill_skb_desc() before the calling of skb_headlen() to fix
this bug.

Fixes: 76ad4f0e

 ("net: hns3: Add support of HNS3 Ethernet Driver for hip08 SoC")
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

commit 547ce4cf ("switch cmsghdr_from_user_compat_to_kern() to
copy_from_user()") missed one of the places where ucmlen should've been
replaced with cmsg.cmsg_len, now that we are fetching the entire struct
rather than doing it field-by-field.

	As the result, compat sendmsg() with several different-sized cmsg
attached started to fail with EINVAL.  Trivial to fix, fortunately.

Fixes: 547ce4cf

 ("switch cmsghdr_from_user_compat_to_kern() to copy_from_user()")
Reported-by: Nick Bowler <nbowler@draconx.ca>
Tested-by: Nick Bowler <nbowler@draconx.ca>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>

Tanner Love says:

====================
selftests/net: Fix clang warnings on powerpc

This is essentially a v2 of
http://patchwork.ozlabs.org/project/netdev/patch/20200724181757.2331172-1-tannerlove.kernel@gmail.com/

,
but it has been split up in order to have only one "Fixes" tag per
patch.
====================

Signed-off-by: David S. Miller <davem@davemloft.net>

When size_t maps to unsigned int (e.g. on 32-bit powerpc), then the
comparison with 1<<35 is always true. Clang 9 threw:
warning: result of comparison of constant 34359738368 with \
expression of type 'size_t' (aka 'unsigned int') is always true \
[-Wtautological-constant-out-of-range-compare]
        while (total < FILE_SZ) {

Tested: make -C tools/testing/selftests TARGETS="net" run_tests

Fixes: 192dc405

 ("selftests: net: add tcp_mmap program")
Signed-off-by: Tanner Love <tannerlove@google.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

On powerpcle, int64_t maps to long long. Clang 9 threw:
warning: absolute value function 'labs' given an argument of type \
'long long' but has parameter of type 'long' which may cause \
truncation of value [-Wabsolute-value]
        if (labs(tstop - texpect) > cfg_variance_us)

Tested: make -C tools/testing/selftests TARGETS="net" run_tests

Fixes: af5136f9

 ("selftests/net: SO_TXTIME with ETF and FQ")
Signed-off-by: Tanner Love <tannerlove@google.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Clang 9 threw:
warning: format specifies type 'unsigned short' but the argument has \
type 'int' [-Wformat]
                typeflags, PORT_BASE, PORT_BASE + port_off);

Tested: make -C tools/testing/selftests TARGETS="net" run_tests

Fixes: 77f65ebd

 ("packet: packet fanout rollover during socket overload")
Signed-off-by: Tanner Love <tannerlove@google.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The signedness of char is implementation-dependent. Some systems
(including PowerPC and ARM) use unsigned char. Clang 9 threw:
warning: result of comparison of constant -1 with expression of type \
'char' is always true [-Wtautological-constant-out-of-range-compare]
                                  &arg_index)) != -1) {

Tested: make -C tools/testing/selftests TARGETS="net" run_tests

Fixes: 16e78122

 ("selftests/net: Add a test to validate behavior of rx timestamps")
Signed-off-by: Tanner Love <tannerlove@google.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The next hw timestamp should be snapshoot to the read registers
only once the current timestamp has been read.
If none of the pending skbs matches the current HW timestamp
just gracefully flush the available timestamp by reading it.

Signed-off-by: laurent brando <laurent.brando@nxp.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Unblocking sockets used for outgoing connections were not containing
inet info about the initial connection due to a typo there: the value of
"err" variable is negative in the kernelspace.

This fixes the creation of additional subflows where the remote port has
to be reused if the other host didn't announce another one. This also
fixes inet_diag showing blank info about MPTCP sockets from unblocking
sockets doing a connect().

Fixes: 41be81a8

 ("mptcp: fix unblocking connect()")
Signed-off-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Acked-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge tag 'riscv-for-linus-5.8-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux into master

Pull RISC-V fixes from Palmer Dabbelt:
 "A few more fixes this week:

   - A fix to avoid using SBI calls during kasan initialization, as the
     SBI calls themselves have not been probed yet.

   - Three fixes related to systems with multiple memory regions"

* tag 'riscv-for-linus-5.8-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux:
  riscv: Parse all memory blocks to remove unusable memory
  RISC-V: Do not rely on initrd_start/end computed during early dt parsing
  RISC-V: Set maximum number of mapped pages correctly
  riscv: kasan: use local_tlb_flush_all() to avoid uninitialized __sbi_rfence

Merge tag 'x86-urgent-2020-07-25' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip into master

Pull x86 fixes from Ingo Molnar:
 "Misc fixes:

   - Fix a section end page alignment assumption that was causing
     crashes

   - Fix ORC unwinding on freshly forked tasks which haven't executed
     yet and which have empty user task stacks

   - Fix the debug.exception-trace=1 sysctl dumping of user stacks,
     which was broken by recent maccess changes"

* tag 'x86-urgent-2020-07-25' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/dumpstack: Dump user space code correctly again
  x86/stacktrace: Fix reliable check for empty user task stacks
  x86/unwind/orc: Fix ORC for newly forked tasks
  x86, vmlinux.lds: Page-align end of ..page_aligned sections

Merge tag 'perf-urgent-2020-07-25' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip into master

Pull uprobe fix from Ingo Molnar:
 "Fix an interaction/regression between uprobes based shared library
  tracing & GDB"

* tag 'perf-urgent-2020-07-25' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  uprobes: Change handle_swbp() to send SIGTRAP with si_code=SI_KERNEL, to fix GDB regression