When set otg_sel(SSUSB_U2_PORT_OTG_SEL) for u2port which supports
dual-role mode, the controller will automatically switch mode
between host and device according to IDDIG signal. But if the
u2port only supports device mode, and no IDDIG pin is provided,
setting otg_sel may cause failure of detection by host.
So set it only for dual-role mode.

Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

Treat dr_mode of USB_DR_MODE_UNKNOWN as USB_DR_MODE_OTG to
enhance functional robustness.

Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

When dr_mode is set as USB_DR_MODE_HOST, it's better to try to
get optional vbus, this can increase flexibility, although we
can set vbus as always on for regulator or put it in host driver
to turn it on.

Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

Support SuperSpeedPlus for usb3.1 device IP

Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

In order to keep manual DRD switch independent on IDDIG interrupt,
make use of FORCE/RG_IDDIG instead of IDDIG EINT interrupt to
implement manual DRD switch function.

Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

add support for 36-bit DMA address

[ Felipe Balbi: fix printk format for dma_addr_t ]

Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

There are mcu_bus and dma_bus clocks needed to be turned on/off by
driver on some SoCs, so add them as optional ones

Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

The wakeup debounce clocks for each ports in fact are not
needed, so remove them.

Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

Add support to disable specific usb3 ports, it's useful when
usb3 phy is shared with PCIe or SATA, because we should disable
the corresponding usb3 port if the phy is used by PCIe or SATA.

Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

When failing to get IRQ number, platform_get_irq() may return
-EPROBE_DEFER, but we ignore it and always return -ENODEV,
so fix it.

Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

Many variables in ep0 are set but never used, so should be removed.

Signed-off-by: Christos Gkekas <chris.gekas@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

This patch adds the dwc2_set_params function for STM32F7xx USB OTG HS.

Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

This patch adds binding documentation for DWC2 controller in HS mode found
on STMicroelectronics STM32F7xx SoC.

Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

Make this const as it is only stored in the const field of a structure
video_device in the file referencing it. Make the declaration const too.

Done using Coccinelle.

Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

Use the of_device_get_match_data() helper instead of open coding,
postponing the matching until when it's really needed.
Note that the renesas_usb3 driver is used with DT only, so there's
always a valid match.

Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

Use the of_device_get_match_data() helper instead of open coding.

Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

This patch adds support for generic phy as an optional. If you want
to use a generic phy (e.g. phy-rcar-gen3-usb3 driver) on this driver,
you have to do "insmod phy-rcar-gen3-usb3.ko" first for now.

Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

This patch adds support suspend/resume functions

Signed-off-by: Kazuya Mizuguchi <kazuya.mizuguchi.ks@renesas.com>
[shimoda: add the commit log]
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

This patch moves pm_runtime_{en,dis}able() call timing to
renesas_usb3_{probe,remove}() for supporting PM_SLEEP feature in
the future.

Signed-off-by: Kazuya Mizuguchi <kazuya.mizuguchi.ks@renesas.com>
[shimoda: Revise the commit log]
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

This patch adds support for R-Car D3. This SoC needs to release
the PLL reset by the UGCTRL register. So, since this is not the same
as other R-Car Gen3 SoCs, this patch adds a new type as
"USBHS_TYPE_RCAR_GEN3_WITH_PLL".

Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

This patch unifies the Gen2 and Gen3 pipe_config setting on
usbhs_parse_dt().

Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

mxs phy has data pin contact and usb charger detector blocks which
can be controlled by software to detect charger type for SDP, CDP and
DCP.

Reviewed-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Li Jun <jun.li@nxp.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

Now that all the information we need sits in struct dwc3_ep, we can
start taking only a pointer to struct dwc3_ep as an argument. This
allows us to clean the code up a bit.

Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

This is in preparation to simplifying prototype of
__dwc3_gadget_kick_transfer().

Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

There is more possibility for sharing code if we just realise that now
__dwc3_gadget_kic_transfer() knows to break out early if there are no
TRBs left.

Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

This will let us call __dwc3_gadget_kick_transfer()
unconditionally. No functional changes, cleanup only.

Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

If the clock handle is given in the DT, it means the clock is required
for proper operation of the PHY. In that case a failure to obtain the
clock must be propagated to stop the driver from probing. This fixes
working with clocks, which request probe deferral.

Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

A couple of structures in <linux/usb/gadget.h> have incomplete kerneldoc
comments, leading to these warnings in the docs build:

./include/linux/usb/gadget.h:230: warning: No description found for parameter 'claimed'
./include/linux/usb/gadget.h:230: warning: No description found for parameter 'enabled'
./include/linux/usb/gadget.h:412: warning: No description found for parameter 'quirk_altset_not_supp'
./include/linux/usb/gadget.h:412: warning: No description found for parameter 'quirk_stall_not_supp'
./include/linux/usb/gadget.h:412: warning: No description found for parameter 'quirk_zlp_not_supp'

Document those fields to make the warnings go away.

Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

The dummy-hcd driver doesn't support emulation of isochronous
transfers.  Therefore it doesn't need to export isochronous endpoint
descriptors; they can be commented out.

Also, the comments in the source code don't express clearly enough the
fact that isochronous isn't supported.  They need to be more explicit.

Finally, change the error status value we use (in theory) for
isochronous URBs.  checkpatch complains about ENOSYS; EINVAL is more
appropriate (it is documented to mean "ISO madness").

Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

Part of the emulation performed by dummy-hcd is accounting for
bandwidth utilization.  The total amount of data transferred in a
single frame is supposed to be no larger than an actual USB connection
could accommodate.

Currently the driver performs bandwidth limiting only for bulk
transfers; control and periodic transfers are effectively unlimited.
(Presumably drivers were not expected to request extremely large
control or interrupt transfers.)  This patch improves the situation
somewhat by restricting them as well.

The emulation still isn't perfect.  On a real system, even 0-length
transfers use some bandwidth because of transaction overhead
(IN, OUT, ACK, NACK packets) and packet overhead (SYNC, PID, bit
stuffing, CRC, EOP).  Adding in those factors is left as an exercise
for a later patch.

Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

Pull SCSI fixes from James Bottomley:

 - a couple of serious fixes: use after free and blacklist for WRITE
   SAME

 - one error leg fix: write_pending failure

 - one user experience problem: do not override max_sectors_kb

 - one minor unused function removal

* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
  scsi: ibmvscsis: Fix write_pending failure path
  scsi: libiscsi: Remove iscsi_destroy_session
  scsi: libiscsi: Fix use-after-free race during iscsi_session_teardown
  scsi: sd: Do not override max_sectors_kb sysfs setting
  scsi: sd: Implement blacklist option for WRITE SAME w/ UNMAP

Pull i2c fixes from Wolfram Sang:
 "I2C has three driver fixes for the newly introduced drivers and one ID
  addition for the i801 driver"

* 'i2c/for-current-4.14' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
  i2c: i2c-stm32f7: make structure stm32f7_setup static const
  i2c: ensure termination of *_device_id tables
  i2c: i801: Add support for Intel Cedar Fork
  i2c: stm32f7: fix setup structure

Pull MMC fixes from Ulf Hansson:
 "MMC core:

   - Fix driver strength selection when selecting hs400es

   - Delete bounce buffer handling:

     This change fixes a problem related to how bounce buffers are being
     allocated. However, instead of trying to fix that, let's just
     remove the mmc bounce buffer code altogether, as it has practically
     no use.

  MMC host:

   - meson-gx: A couple of fixes related to clock/phase/tuning

   - sdhci-xenon: Fix clock resource by adding an optional bus clock"

* tag 'mmc-v4.14-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc:
  mmc: sdhci-xenon: Fix clock resource by adding an optional bus clock
  mmc: meson-gx: include tx phase in the tuning process
  mmc: meson-gx: fix rx phase reset
  mmc: meson-gx: make sure the clock is rounded down
  mmc: Delete bounce buffer handling
  mmc: core: add driver strength selection when selecting hs400es

Merge tag 'hwmon-for-linus-v4.14-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging

Pull hwmon fix from Guenter Roeck:
 "Fix up error path in xgene driver"

* tag 'hwmon-for-linus-v4.14-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
  hwmon: (xgene) Fix up error handling path mixup in 'xgene_hwmon_probe()'

Pull clk fixes from Stephen Boyd:

 - build fix to export the clk_bulk_prepare() symbol

 - suspend fix for Samsung Exynos SoCs where we need to keep clks on
   across suspend

 - two critical clk markings for clks that shouldn't ever turn off on
   Rockchip SoCs

 - a fix for a copy-paste mistake on Rockchip rk3128 causing some clks
   to touch the same bit and trample over one another

* tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux:
  clk: samsung: exynos4: Enable VPLL and EPLL clocks for suspend/resume cycle
  clk: Export clk_bulk_prepare()
  clk: rockchip: add sclk_timer5 as critical clock on rk3128
  clk: rockchip: fix up rk3128 pvtm and mipi_24m gate regs error
  clk: rockchip: add pclk_pmu as critical clock on rk3128

Pull ARC udpates from Vineet Gupta:

 - updates for various platforms

 - boot log updates for upcoming HS48 family of cores (dual issue)

* tag 'arc-4.14-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc:
  ARC: [plat-hsdk]: Add reset controller node to manage ethernet reset
  ARC: [plat-hsdk]: Temporary fix to set CPU frequency to 1GHz
  ARC: fix allnoconfig build warning
  ARCv2: boot log: identify HS48 cores (dual issue)
  ARC: boot log: decontaminate ARCv2 ISA_CONFIG register
  arc: remove redundant UTS_MACHINE define in arch/arc/Makefile
  ARC: [plat-eznps] Update platform maintainer as Noam left
  ARC: [plat-hsdk] use actual clk driver to manage cpu clk
  ARC: [*defconfig] Reenable soft lock-up detector
  ARC: [plat-axs10x] sdio: Temporary fix of sdio ciu frequency
  ARC: [plat-hsdk] sdio: Temporary fix of sdio ciu frequency
  ARC: [plat-axs103] Add temporary quirk to reset ethernet IP

Pull xfs fixes from Darrick Wong:

 - fix a race between overlapping copy on write aio

 - fix cow fork swapping when we defragment reflinked files

* tag 'xfs-4.14-fixes-4' of git://git.kernel.org/pub/scm/fs/xfs/xfs-linux:
  xfs: handle racy AIO in xfs_reflink_end_cow
  xfs: always swap the cow forks when swapping extents

Pull block fixes from Jens Axboe:
 "A collection of fixes for this series. This contains:

   - NVMe pull request from Christoph, one uuid attribute fix, and one
     fix for the controller memory buffer address for remapped BARs.

   - use-after-free fix for bsg, from Benjamin Block.

   - bcache race/use-after-free fix for a list traversal, fixing a
     regression in this merge window. From Coly Li.

   - null_blk change configfs dependency change from a 'depends' to a
     'select'. This is a change from this merge window as well. From me.

   - nbd signal fix from Josef, fixing a regression introduced with the
     status code changes.

   - nbd MAINTAINERS mailing list entry update.

   - blk-throttle stall fix from Joseph Qi.

   - blk-mq-debugfs fix from Omar, fixing an issue where we don't
     register the IO scheduler debugfs directory, if the driver is
     loaded with it. Only shows up if you switch through the sysfs
     interface"

* 'for-linus' of git://git.kernel.dk/linux-block:
  bsg-lib: fix use-after-free under memory-pressure
  nvme-pci: Use PCI bus address for data/queues in CMB
  blk-mq-debugfs: fix device sched directory for default scheduler
  null_blk: change configfs dependency to select
  blk-throttle: fix possible io stall when upgrade to max
  MAINTAINERS: update list for NBD
  nbd: fix -ERESTARTSYS handling
  nvme: fix visibility of "uuid" ns attribute
  bcache: use llist_for_each_entry_safe() in __closure_wake_up()

Pull PCI fixes from Bjorn Helgaas:
 "Fix legacy IDE probe issues exposed by recent PCI core IRQ mapping
  changes (Bartlomiej Zolnierkiewicz, Lorenzo Pieralisi)"

* tag 'pci-v4.14-fixes-4' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
  ide: fix IRQ assignment for PCI bus order probing
  ide: pci: free PCI BARs on initialization failure
  ide: free hwif->portdev on hwif_init() failure