In full-resolution mode, the LPF_INTENSITY_EN and LPF_INTENSITY
registers control Quad Bayer Re-mosaic broken line correction.
Expose this as a module parameter "qbc_adjust": zero disables
the correction and values in the range 2 to 5 set its strength.

There is a trade-off between coloured and monochrome patterns.
The previous fixed value 4 could produce ladder/spots artefacts
in coloured textures. The new default value 2 may suit a wider
range of scenes.

Signed-off-by: Nick Hollinghurst <nick.hollinghurst@raspberrypi.com>

With a DMA FIFO threshold greater than 1 (encoded as 0), it is possible
for data in the FIFO to be inaccessible, causing the transfer to fail
after a timeout. If the transfer includes a transmission, reduce the
RX threshold when the TX completes, otherwise use 1 for the whole
transfer (inefficient, but not catastrophic at SPI data rates).

See: https://github.com/raspberrypi/linux/issues/5696



Signed-off-by: Phil Elwell <phil@raspberrypi.com>

BCM2711 runs pixelvalve at two pixels per clock cycle which results
in an unfortunate limitation that odd horizontal timings are not
possible. This is apparent on the standard DMT mode of 1366x768@60
which cannot be driven with correct timing.

BCM2712 defaults to the same behaviour, but has a mode to support
odd timings. While internally it still runs at two pixels per clock,
setting the PV_VCONTROL_ODD_TIMING bit makes it appear externally
to behave as it is one pixel per clock.

Switching to this mode fixes 1366x768@60 mode, and other custom
resultions with odd horizontal timings.

Signed-off-by: Dom Cobley <popcornmix@gmail.com>

Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>

Users are reporting running out of DLIST memory. Add a
debugfs file to dump out all the allocations.

Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>

The code handling freeing stale dlists had 2 issues:
- it disabled the interrupt as soon as the first EOF interrupt
  occurred, even if it didn't clear all stale allocations, thus
  leading to stale entries
- It didn't free stale entries from disabled channels, so eg
  "kmstest -c 0" could leave a stale alloc on channel 1 floating
  around.

Keep the interrupt enabled whilst there are any outstanding
allocs, and discard those on disabled channels. This second
channel does require us to call vc4_hvs_stop_channel from
vc4_crtc_atomic_disable so that the channel actually gets stopped.

Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>

The reset condition for the EMPTY flag in DISPSTATx is 0,
so seeing as we've just reset the pipeline there is no
guarantee that the flag will denote empty if it hasn't been
enabled.

Drop the WARN.

Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>

When factoring out __vc4_hvs_stop_channel, the logic got inverted from
	if (condition)
	  // stop channel
to
	if (condition)
	  goto out
	//stop channel
	out:
and also changed the exact register writes used to stop the channel.

Correct the logic so that the channel is actually stopped, and revert
to the original register writes.

Fixes: 6d01a106

 ("drm/vc4: crtc: Move HVS init and close to a function")
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>

This control is meant to be read-only, mark it as such.

Signed-off-by: Naushir Patuck <naush@raspberrypi.com>

Add V4L2_CID_LINK_FREQ as a read-only control with a value of 450 Mhz.
This will be used by the CFE driver to corretly setup the DPHY timing
parameters in the CSI-2 block.

Signed-off-by: Naushir Patuck <naush@raspberrypi.com>

Without the pinctrl-0 property in the overlays, the UARTs may not be
mapped correctly.

Signed-off-by: Phil Elwell <phil@raspberrypi.com>

spi6 won't be useful on Pi 5 because it can't be enabled on the 40-pin
header, but include it for completeness.

Also fix the #address-cells value for spi1, otherwise the kernel will
reject attempts to apply the, say, spi1-2cs overlay at runtime.

Signed-off-by: Phil Elwell <phil@raspberrypi.com>

The kernel now treats multiple fragments targeting the same node as an
error. For this reason, it is important that labels created just for
compatibility with other systems (e.g. i2c0if and i2c0mux) are
attached to unique nodes, not just tacked onto existing nodes.

Signed-off-by: Phil Elwell <phil@raspberrypi.com>

Use the sensor provided link frequency to set the DPHY timing parameters
on stream_on. This replaces the hard-coded 999 MHz value currently being
used. As a fallback, revert to the original 999 Mhz link frequency.

As a drive-by, fix a 80-character line formatting error.

Signed-off-by: Naushir Patuck <naush@raspberrypi.com>

Link: https://lore.kernel.org/r/20231031165918.608547597@linuxfoundation.org


Tested-by: Pavel Machek (CIP) <pavel@denx.de>
Tested-by: Florian Fainelli <florian.fainelli@broadcom.com>
Tested-by: Shuah Khan <skhan@linuxfoundation.org>
Tested-by: Bagas Sanjaya <bagasdotme@gmail.com>
Tested-by: Jon Hunter <jonathanh@nvidia.com>
Tested-by: Ron Economos <re@w6rz.net>
Tested-by: Ricardo B. Marliere <ricardo@marliere.net>
Tested-by: Takeshi Ogasawara <takeshi.ogasawara@futuring-girl.com>
Tested-by: Linux Kernel Functional Testing <lkft@linaro.org>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Tested-by: Allen Pais <apais@linux.microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

When dbf46008

 ("objtool/x86: Fixup frame-pointer vs rethunk")
was backported to some stable branches, the check for dest->embedded_insn
in is_special_call() was missed.  The result is that the warning it
was intended to suppress still appears.  For example on 6.1 (on kernels
before 6.1, the '-s' argument would instead be 'check'):

$ tools/objtool/objtool -s arch/x86/lib/retpoline.o
arch/x86/lib/retpoline.o: warning: objtool: srso_untrain_ret+0xd:
    call without frame pointer save/setup

With this patch, the warning is correctly suppressed, and the
kernel still passes the normal Google kernel developer tests.

Signed-off-by: John Sperbeck <jsperbeck@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit bedc5d34

 upstream.

Let's say we want to allocate 2 blocks starting from 4294966386, after
predicting the file size, start is aligned to 4294965248, len is changed
to 2048, then end = start + size = 0x100000000. Since end is of
type ext4_lblk_t, i.e. uint, end is truncated to 0.

This causes (pa->pa_lstart >= end) to always hold when checking if the
current extent to be allocated crosses already preallocated blocks, so the
resulting ac_g_ex may cross already preallocated blocks. Hence we convert
the end type to loff_t and use pa_logical_end() to avoid overflow.

Signed-off-by: Baokun Li <libaokun1@huawei.com>
Reviewed-by: Ritesh Harjani (IBM) <ritesh.list@gmail.com>
Link: https://lore.kernel.org/r/20230724121059.11834-4-libaokun1@huawei.com


Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Baokun Li <libaokun1@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit bc056e71 upstream.

When we calculate the end position of ext4_free_extent, this position may
be exactly where ext4_lblk_t (i.e. uint) overflows. For example, if
ac_g_ex.fe_logical is 4294965248 and ac_orig_goal_len is 2048, then the
computed end is 0x100000000, which is 0. If ac->ac_o_ex.fe_logical is not
the first case of adjusting the best extent, that is, new_bex_end > 0, the
following BUG_ON will be triggered:

=========================================================
kernel BUG at fs/ext4/mballoc.c:5116!
invalid opcode: 0000 [#1] PREEMPT SMP PTI
CPU: 3 PID: 673 Comm: xfs_io Tainted: G E 6.5.0-rc1+ #279
RIP: 0010:ext4_mb_new_inode_pa+0xc5/0x430
Call Trace:
 <TASK>
 ext4_mb_use_best_found+0x203/0x2f0
 ext4_mb_try_best_found+0x163/0x240
 ext4_mb_regular_allocator+0x158/0x1550
 ext4_mb_new_blocks+0x86a/0xe10
 ext4_ext_map_blocks+0xb0c/0x13a0
 ext4_map_blocks+0x2cd/0x8f0
 ext4_iomap_begin+0x27b/0x400
 iomap_iter+0x222/0x3d0
 __iomap_dio_rw+0x243/0xcb0
 iomap_dio_rw+0x16/0x80
=========================================================

A simple reproducer demonstrating the problem:

	mkfs.ext4 -F /dev/sda -b 4096 100M
	mount /dev/sda /tmp/test
	fallocate -l1M /tmp/test/tmp
	fallocate -l10M /tmp/test/file
	fallocate -i -o 1M -l16777203M /tmp/test/file
	fsstress -d /tmp/test -l 0 -n 100000 -p 8 &
	sleep 10 && killall -9 fsstress
	rm -f /tmp/test/tmp
	xfs_io -c "open -ad /tmp/test/file" -c "pwrite -S 0xff 0 8192"

We simply refactor the logic for adjusting the best extent by adding
a temporary ext4_free_extent ex and use extent_logical_end() to avoid
overflow, which also simplifies the code.

Cc: stable@kernel.org # 6.4
Fixes: 93cdf49f

 ("ext4: Fix best extent lstart adjustment logic in ext4_mb_new_inode_pa()")
Signed-off-by: Baokun Li <libaokun1@huawei.com>
Reviewed-by: Ritesh Harjani (IBM) <ritesh.list@gmail.com>
Link: https://lore.kernel.org/r/20230724121059.11834-3-libaokun1@huawei.com


Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Baokun Li <libaokun1@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 43bbddc0

 upstream.

When we use lstart + len to calculate the end of free extent or prealloc
space, it may exceed the maximum value of 4294967295(0xffffffff) supported
by ext4_lblk_t and cause overflow, which may lead to various problems.

Therefore, we add two helper functions, extent_logical_end() and
pa_logical_end(), to limit the type of end to loff_t, and also convert
lstart to loff_t for calculation to avoid overflow.

Signed-off-by: Baokun Li <libaokun1@huawei.com>
Reviewed-by: Ritesh Harjani (IBM) <ritesh.list@gmail.com>
Link: https://lore.kernel.org/r/20230724121059.11834-2-libaokun1@huawei.com


Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Baokun Li <libaokun1@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 3bde7ec1 upstream.

When suspending to idle and resuming on some Lenovo laptops using the
Mendocino APU, multiple NVME IOMMU page faults occur, showing up in
dmesg as repeated errors:

nvme 0000:01:00.0: AMD-Vi: Event logged [IO_PAGE_FAULT domain=0x000b
address=0xb6674000 flags=0x0000]

The system is unstable afterwards.

Applying the s2idle quirk introduced by commit 455cd867 ("platform/x86:
thinkpad_acpi: Add a s2idle resume quirk for a number of laptops")
allows these systems to work with the IOMMU enabled and s2idle
resume to work.

Closes: https://bugzilla.kernel.org/show_bug.cgi?id=218024


Suggested-by: Mario Limonciello <mario.limonciello@amd.com>
Suggested-by: Mark Pearson <mpearson-lenovo@squebb.ca>
Signed-off-by: David Lazar <dlazar@gmail.com>
Reviewed-by: Mario Limonciello <mario.limonciello@amd.com>
Reviewed-by: Mark Pearson <mpearson-lenovo@squebb.ca>
Link: https://lore.kernel.org/r/ZTlsyOaFucF2pWrL@localhost


Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit ceb87a36 upstream.

In the possible_parent_show function, ensure proper handling of the return
value from of_clk_get_parent_name to prevent potential issues arising from
a NULL return.
The current implementation invokes seq_puts directly on the result of
of_clk_get_parent_name without verifying the return value, which can lead
to kernel panic if the function returns NULL.

This patch addresses the concern by introducing a check on the return
value of of_clk_get_parent_name. If the return value is not NULL, the
function proceeds to call seq_puts, providing the returned value as
argument.
However, if of_clk_get_parent_name returns NULL, the function provides a
static string as argument, avoiding the panic.

Fixes: 1ccc0ddf

 ("clk: Use seq_puts() in possible_parent_show()")
Reported-by: Philip Daly <pdaly@redhat.com>
Signed-off-by: Alessandro Carminati (Red Hat) <alessandro.carminati@gmail.com>
Link: https://lore.kernel.org/r/20230921073217.572151-1-alessandro.carminati@gmail.com


Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 1f36cd05 upstream.

Fault handler used to make non-trivial calls, so it needed
to set a stack frame up.  Used to be
	save ... - grab a stack frame, old %o... become %i...
	....
	ret	- go back to address originally in %o7, currently %i7
	 restore - switch to previous stack frame, in delay slot
Non-trivial calls had been gone since ab5e8b33

 and that code should
have become
	retl	- go back to address in %o7
	 clr %o0 - have return value set to 0
What it had become instead was
	ret	- go back to address in %i7 - return address of *caller*
	 clr %o0 - have return value set to 0
which is not good, to put it mildly - we forcibly return 0 from
csum_and_copy_{from,to}_iter() (which is what the call of that
thing had been inlined into) and do that without dropping the
stack frame of said csum_and_copy_..._iter().  Confuses the
hell out of the caller of csum_and_copy_..._iter(), obviously...

Reviewed-by: Sam Ravnborg <sam@ravnborg.org>
Fixes: ab5e8b33

 "sparc32: propagate the calling conventions change down to __csum_partial_copy_sparc_generic()"
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit a71ef314 upstream.

Smatch is awesome.

Fixes: 32671e37

 ("perf: Disallow mis-matched inherited group reads")
Reported-by: Dan Carpenter <dan.carpenter@linaro.org>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit b99d70c0

 upstream.

For "reasons" Intel has code-named this CPU with a "_H" suffix.

[ dhansen: As usual, apply this and send it upstream quickly to
	   make it easier for anyone who is doing work that
	   consumes this. ]

Signed-off-by: Tony Luck <tony.luck@intel.com>
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com>
Link: https://lore.kernel.org/all/20231025202513.12358-1-tony.luck%40intel.com


Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 128b0c97 upstream.

David and a few others reported that on certain newer systems some legacy
interrupts fail to work correctly.

Debugging revealed that the BIOS of these systems leaves the legacy PIC in
uninitialized state which makes the PIC detection fail and the kernel
switches to a dummy implementation.

Unfortunately this fallback causes quite some code to fail as it depends on
checks for the number of legacy PIC interrupts or the availability of the
real PIC.

In theory there is no reason to use the PIC on any modern system when
IO/APIC is available, but the dependencies on the related checks cannot be
resolved trivially and on short notice. This needs lots of analysis and
rework.

The PIC detection has been added to avoid quirky checks and force selection
of the dummy implementation all over the place, especially in VM guest
scenarios. So it's not an option to revert the relevant commit as that
would break a lot of other scenarios.

One solution would be to try to initialize the PIC on detection fail and
retry the detection, but that puts the burden on everything which does not
have a PIC.

Fortunately the ACPI/MADT table header has a flag field, which advertises
in bit 0 that the system is PCAT compatible, which means it has a legacy
8259 PIC.

Evaluate that bit and if set avoid the detection routine and keep the real
PIC installed, which then gets initialized (for nothing) and makes the rest
of the code with all the dependencies work again.

Fixes: e179f691

 ("x86, irq, pic: Probe for legacy PIC and set legacy_pic appropriately")
Reported-by: David Lazar <dlazar@gmail.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: David Lazar <dlazar@gmail.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Mario Limonciello <mario.limonciello@amd.com>
Cc: stable@vger.kernel.org
Closes: https://bugzilla.kernel.org/show_bug.cgi?id=218003
Link: https://lore.kernel.org/r/875y2u5s8g.ffs@tglx


Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 7d6e10f5 upstream.

The nregs for i.MX6UL should be 144 per fuse map, correct it.

Fixes: 4aa2b480

 ("nvmem: octop: Add support for imx6ul")
Cc: Stable@vger.kernel.org
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20231013124904.175782-3-srinivas.kandagatla@linaro.org


Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 414a98ab upstream.

The nregs for i.MX6SLL should be 80 per fuse map, correct it.

Fixes: 6da27821

 ("nvmem: imx-ocotp: add support for imx6sll")
Cc: Stable@vger.kernel.org
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20231013124904.175782-2-srinivas.kandagatla@linaro.org


Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 2382c1b0 upstream.

The nregs for i.MX6ULL should be 80 per fuse map, correct it.

Fixes: ffbc34bf

 ("nvmem: imx-ocotp: Implement i.MX6ULL/ULZ support")
Cc: Stable@vger.kernel.org
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20231013124904.175782-4-srinivas.kandagatla@linaro.org


Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 50914338 upstream.

For unmapping any buffer from kernel, it should first be unmapped
from DSP. In case unmap from DSP request fails, the map should not
be removed from kernel as it might lead to SMMU faults and other
memory issues.

Fixes: 5c1b97c7

 ("misc: fastrpc: add support for FASTRPC_IOCTL_MEM_MAP/UNMAP")
Cc: stable <stable@kernel.org>
Signed-off-by: Ekansh Gupta <quic_ekangupt@quicinc.com>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20231013122007.174464-5-srinivas.kandagatla@linaro.org


Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 1c809359 upstream.

With current design, buffers and dma handles are not freed in case
of remote invocation failures returned from DSP. This could result
in buffer leakings and dma handle pointing to wrong memory in the
fastrpc kernel. Adding changes to clean buffers and dma handles
even when remote invocation to DSP returns failures.

Fixes: c68cfb71

 ("misc: fastrpc: Add support for context Invoke method")
Cc: stable <stable@kernel.org>
Signed-off-by: Ekansh Gupta <quic_ekangupt@quicinc.com>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20231013122007.174464-4-srinivas.kandagatla@linaro.org


Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 20648430 upstream.

The FDs for DMA handles to be freed is updated in fdlist by DSP over
a remote call. This holds true even for remote calls with no
arguments. To handle this, get_args and put_args are needed to
be called for remote calls with no arguments also as fdlist
is allocated in get_args and FDs updated in fdlist is freed
in put_args.

Fixes: 8f6c1d8c

 ("misc: fastrpc: Add fdlist implementation")
Cc: stable <stable@kernel.org>
Signed-off-by: Ekansh Gupta <quic_ekangupt@quicinc.com>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20231013122007.174464-3-srinivas.kandagatla@linaro.org


Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 1c29d801 upstream.

Metadata buffer is allocated during get_args for any remote call.
This buffer carries buffers, fdlists and other payload information
for the call. If the buffer is not reset, put_args might find some
garbage FDs in the fdlist which might have an existing mapping in
the list. This could result in improper freeing of FD map when DSP
might still be using the buffer. Added change to reset the metadata
buffer after allocation.

Fixes: 8f6c1d8c

 ("misc: fastrpc: Add fdlist implementation")
Cc: stable <stable@kernel.org>
Signed-off-by: Ekansh Gupta <quic_ekangupt@quicinc.com>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20231013122007.174464-2-srinivas.kandagatla@linaro.org


Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit e0f83183 upstream.

Fix the following kernel-doc warnings:

kernel/trace/trace_kprobe.c:1029: warning: Excess function parameter 'args' description in '__kprobe_event_gen_cmd_start'
kernel/trace/trace_kprobe.c:1097: warning: Excess function parameter 'args' description in '__kprobe_event_add_fields'

Refer to the usage of variable length arguments elsewhere in the kernel
code, "@..." is the proper way to express it in the description.

Link: https://lore.kernel.org/all/20231027041315.2613166-1-yujie.liu@intel.com/

Fixes: 2a588dd1

 ("tracing: Add kprobe event command generation functions")
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202310190437.paI6LYJF-lkp@intel.com/


Signed-off-by: Yujie Liu <yujie.liu@intel.com>
Reviewed-by: Mukesh Ojha <quic_mojha@quicinc.com>
Acked-by: Masami Hiramatsu (Google) <mhiramat@kernel.org>
Signed-off-by: Masami Hiramatsu (Google) <mhiramat@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 54f1840d upstream.

When the `CONFIG_I2C_SLAVE` option is enabled and the device operates
as a slave, a situation arises where the master sends a START signal
without the accompanying STOP signal. This action results in a
persistent I2C bus timeout. The core issue stems from the fact that
the i2c controller remains in a slave read state without a timeout
mechanism. As a consequence, the bus perpetually experiences timeouts.

In this case, the i2c bus will be reset, but the slave_state reset is
missing.

Fixes: fee46515

 ("i2c: aspeed: Reset the i2c controller when timeout occurs")
Signed-off-by: Jian Zhang <zhangjian.3032@bytedance.com>
Acked-by: Andi Shyti <andi.shyti@kernel.org>
Tested-by: Andrew Jeffery <andrew@codeconstruct.com.au>
Reviewed-by: Andrew Jeffery <andrew@codeconstruct.com.au>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit c896ff2d upstream.

In case of SMBUS byte read with PEC enabled, the whole transfer
is split into two commands.  A first write command, followed by
a read command.  The write command does not have any PEC byte
and a PEC byte is appended at the end of the read command.
(cf Read byte protocol with PEC in SMBUS specification)

Within the STM32 I2C controller, handling (either sending
or receiving) of the PEC byte is done via the PECBYTE bit in
register CR2.

Currently, the PECBYTE is set at the beginning of a transfer,
which lead to sending a PEC byte at the end of the write command
(hence losing the real last byte), and also does not check the
PEC byte received during the read command.

This patch corrects the function stm32f7_i2c_smbus_xfer_msg
in order to only set the PECBYTE during the read command.

Fixes: 9e48155f

 ("i2c: i2c-stm32f7: Add initial SMBus protocols support")
Signed-off-by: Alain Volmat <alain.volmat@foss.st.com>
Reviewed-by: Pierre-Yves MORDRET <pierre-yves.mordret@foss.st.com>
Acked-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 0fb118de upstream.

i2c-demux-pinctrl uses the pair of_find_i2c_adapter_by_node() /
i2c_put_adapter(). These pair alone is not correct to properly lock the
I2C parent adapter.

Indeed, i2c_put_adapter() decrements the module refcount while
of_find_i2c_adapter_by_node() does not increment it. This leads to an
underflow of the parent module refcount.

Use the	dedicated function, of_get_i2c_adapter_by_node(), to handle
correctly the module refcount.

Fixes: 50a5ba87

 ("i2c: mux: demux-pinctrl: add driver")
Signed-off-by: Herve Codina <herve.codina@bootlin.com>
Cc: stable@vger.kernel.org
Acked-by: Peter Rosin <peda@axentia.se>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 3dc0ec46 upstream.

i2c-mux-gpmux uses the pair of_find_i2c_adapter_by_node() /
i2c_put_adapter(). These pair alone is not correct to properly lock the
I2C parent adapter.

Indeed, i2c_put_adapter() decrements the module refcount while
of_find_i2c_adapter_by_node() does not increment it. This leads to an
underflow of the parent module refcount.

Use the dedicated function, of_get_i2c_adapter_by_node(), to handle
correctly the module refcount.

Fixes: ac8498f0

 ("i2c: i2c-mux-gpmux: new driver")
Signed-off-by: Herve Codina <herve.codina@bootlin.com>
Cc: stable@vger.kernel.org
Acked-by: Peter Rosin <peda@axentia.se>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 3171d37b upstream.

i2c-mux-pinctrl uses the pair of_find_i2c_adapter_by_node() /
i2c_put_adapter(). These pair alone is not correct to properly lock the
I2C parent adapter.

Indeed, i2c_put_adapter() decrements the module refcount while
of_find_i2c_adapter_by_node() does not increment it. This leads to an
underflow of the parent module refcount.

Use the dedicated function, of_get_i2c_adapter_by_node(), to handle
correctly the module refcount.

Fixes: c4aee3e1

 ("i2c: mux: pinctrl: remove platform_data")
Signed-off-by: Herve Codina <herve.codina@bootlin.com>
Cc: stable@vger.kernel.org
Acked-by: Peter Rosin <peda@axentia.se>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit e2bd8c28 upstream.

The driver was previously using offset and scale values for the
temperature sensor readings which were only valid for 7-series devices.
Add per-device-type values for offset and scale and set them appropriately
for each device type.

Note that the values used for the UltraScale family are for UltraScale+
(i.e. the SYSMONE4 primitive) using the internal reference, as that seems
to be the most common configuration and the device tree values Xilinx's
device tree generator produces don't seem to give us anything to tell us
which configuration is used. However, the differences within the UltraScale
family seem fairly minor and it's closer than using the 7-series values
instead in any case.

Fixes: c2b7720a

 ("iio: xilinx-xadc: Add basic support for Ultrascale System Monitor")
Signed-off-by: Robert Hancock <robert.hancock@calian.com>
Acked-by: O'Griofa, Conall <conall.ogriofa@amd.com>
Tested-by: O'Griofa, Conall <conall.ogriofa@amd.com>
Link: https://lore.kernel.org/r/20230915001019.2862964-3-robert.hancock@calian.com


Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>