- Dec 04, 2011
-
-
Pravin B Shelar authored
Open vSwitch uses Generic Netlink interface for communication between userspace and kernel module. genl_notify() is used for sending notification back to userspace. genl_notify() is analogous to rtnl_notify() but uses genl_sock instead of rtnl. Signed-off-by:
Pravin B Shelar <pshelar@nicira.com> Signed-off-by:
Jesse Gross <jesse@nicira.com>
-
- Dec 03, 2011
-
-
David S. Miller authored
Signed-off-by:
David S. Miller <davem@davemloft.net>
-
-
Igor Maravic authored
Moved netdev_completed_queue() out of while loop in function nv_tx_done_optimized(). Because this function was in while loop, BUG_ON(count > dql->num_queued - dql->num_completed) was hit in dql_completed(). Signed-off-by:
Igor Maravic <igorm@etf.rs> Acked-by:
Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
David S. Miller authored
Reported-by:
Thomas Jarosch <thomas.jarosch@intra2net.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
- Dec 02, 2011
-
-
git://git.kernel.org/pub/scm/linux/kernel/git/davem/netLinus Torvalds authored
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (73 commits) netfilter: Remove ADVANCED dependency from NF_CONNTRACK_NETBIOS_NS ipv4: flush route cache after change accept_local sch_red: fix red_change Revert "udp: remove redundant variable" bridge: master device stuck in no-carrier state forever when in user-stp mode ipv4: Perform peer validation on cached route lookup. net/core: fix rollback handler in register_netdevice_notifier sch_red: fix red_calc_qavg_from_idle_time bonding: only use primary address for ARP ipv4: fix lockdep splat in rt_cache_seq_show sch_teql: fix lockdep splat net: fec: Select the FEC driver by default for i.MX SoCs isdn: avoid copying too long drvid isdn: make sure strings are null terminated netlabel: Fix build problems when IPv6 is not enabled sctp: better integer overflow check in sctp_auth_create_key() sctp: integer overflow in sctp_auth_create_key() ipv6: Set mcast_hops to IPV6_DEFAULT_MCASTHOPS when -1 was given. net: Fix corruption in /proc/*/net/dev_mcast mac80211: fix race between the AGG SM and the Tx data path ...
-
David S. Miller authored
firewalld in Fedora 16 needs this. Signed-off-by:
David S. Miller <davem@davemloft.net>
-
David S. Miller authored
Signed-off-by:
David S. Miller <davem@davemloft.net>
-
David S. Miller authored
Reported-by:
Thomas Jarosch <thomas.jarosch@intra2net.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Peter Pan(潘卫平) authored
After reset ipv4_devconf->data[IPV4_DEVCONF_ACCEPT_LOCAL] to 0, we should flush route cache, or it will continue receive packets with local source address, which should be dropped. Signed-off-by:
Weiping Pan <panweiping3@gmail.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Eric Dumazet authored
Le mercredi 30 novembre 2011 à 14:36 -0800, Stephen Hemminger a écrit : > (Almost) nobody uses RED because they can't figure it out. > According to Wikipedia, VJ says that: > "there are not one, but two bugs in classic RED." RED is useful for high throughput routers, I doubt many linux machines act as such devices. I was considering adding Adaptative RED (Sally Floyd, Ramakrishna Gummadi, Scott Shender), August 2001 In this version, maxp is dynamic (from 1% to 50%), and user only have to setup min_th (target average queue size) (max_th and wq (burst in linux RED) are automatically setup) By the way it seems we have a small bug in red_change() if (skb_queue_empty(&sch->q)) red_end_of_idle_period(&q->parms); First, if queue is empty, we should call red_start_of_idle_period(&q->parms); Second, since we dont use anymore sch->q, but q->qdisc, the test is meaningless. Oh well... [PATCH] sch_red: fix red_change() Now RED is classful, we must check q->qdisc->q.qlen, and if queue is empty, we start an idle period, not end it. Signed-off-by:
Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Linus Torvalds authored
-
git://git.kernel.org/pub/scm/linux/kernel/git/jlbec/ocfs2Linus Torvalds authored
* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jlbec/ocfs2: (31 commits) ocfs2: avoid unaligned access to dqc_bitmap ocfs2: Use filemap_write_and_wait() instead of write_inode_now() ocfs2: honor O_(D)SYNC flag in fallocate ocfs2: Add a missing journal credit in ocfs2_link_credits() -v2 ocfs2: send correct UUID to cleancache initialization ocfs2: Commit transactions in error cases -v2 ocfs2: make direntry invalid when deleting it fs/ocfs2/dlm/dlmlock.c: free kmem_cache_zalloc'd data using kmem_cache_free ocfs2: Avoid livelock in ocfs2_readpage() ocfs2: serialize unaligned aio ocfs2: Implement llseek() ocfs2: Fix ocfs2_page_mkwrite() ocfs2: Add comment about orphan scanning ocfs2: Clean up messages in the fs ocfs2/cluster: Cluster up now includes network connections too ocfs2/cluster: Add new function o2net_fill_node_map() ocfs2/cluster: Fix output in file elapsed_time_in_ms ocfs2/dlm: dlmlock_remote() needs to account for remastery ocfs2/dlm: Take inflight reference count for remotely mastered resources too ocfs2/dlm: Cleanup dlm_wait_for_node_death() and dlm_wait_for_node_recovery() ...
-
Akinobu Mita authored
The dqc_bitmap field of struct ocfs2_local_disk_chunk is 32-bit aligned, but not 64-bit aligned. The dqc_bitmap is accessed by ocfs2_set_bit(), ocfs2_clear_bit(), ocfs2_test_bit(), or ocfs2_find_next_zero_bit(). These are wrapper macros for ext2_*_bit() which need to take an unsigned long aligned address (though some architectures are able to handle unaligned address correctly) So some 64bit architectures may not be able to access the dqc_bitmap correctly. This avoids such unaligned access by using another wrapper functions for ext2_*_bit(). The code is taken from fs/ext4/mballoc.c which also need to handle unaligned bitmap access. Signed-off-by:
Akinobu Mita <akinobu.mita@gmail.com> Acked-by:
Joel Becker <jlbec@evilplan.org> Cc: Mark Fasheh <mfasheh@suse.com> Signed-off-by:
Andrew Morton <akpm@linux-foundation.org> Signed-off-by:
Joel Becker <jlbec@evilplan.org>
-
http://ftp.arm.linux.org.uk/pub/linux/arm/kernel/git-cur/linux-2.6-armLinus Torvalds authored
* 'fixes' of http://ftp.arm.linux.org.uk/pub/linux/arm/kernel/git-cur/linux-2.6-arm: ARM: 7182/1: ARM cpu topology: fix warning ARM: 7181/1: Restrict kprobes probing SWP instructions to ARMv5 and below ARM: 7180/1: Change kprobes testcase with unpredictable STRD instruction ARM: 7177/1: GIC: avoid skipping non-existent PPIs in irq_start calculation ARM: 7176/1: cpu_pm: register GIC PM notifier only once ARM: 7175/1: add subname parameter to mfp_set_groupg callers ARM: 7174/1: Fix build error in kprobes test code on Thumb2 kernels ARM: 7172/1: dma: Drop GFP_COMP for DMA memory allocations ARM: 7171/1: unwind: add unwind directives to bitops assembly macros ARM: 7170/2: fix compilation breakage in entry-armv.S ARM: 7168/1: use cache type functions for arch_get_unmapped_area ARM: perf: check that we have a platform device when reserving PMU ARM: 7166/1: Use PMD_SHIFT instead of PGDIR_SHIFT in dma-consistent.c ARM: 7165/2: PL330: Fix typo in _prepare_ccr() ARM: 7163/2: PL330: Only register usable channels ARM: 7162/1: errata: tidy up Kconfig options for PL310 errata workarounds ARM: 7161/1: errata: no automatic store buffer drain ARM: perf: initialise used_mask for fake PMU during validation ARM: PMU: remove pmu_init declaration ARM: PMU: re-export release_pmu symbol to modules
-
David S. Miller authored
Commit 1386be55 ("dccp: fix auto-loading of dccp(_probe)") fixed a bug but created a new compiler warning: net/dccp/probe.c: In function ‘dccpprobe_init’: net/dccp/probe.c:166:2: warning: the omitted middle operand in ?: will always be ‘true’, suggest explicit middle operand [-Wparentheses] try_then_request_module() is built for situations where the "existence" test is some lookup function that returns a non-NULL object on success, and with a reference count of some kind held. Here we're looking for a success return of zero from the jprobe registry. Instead of fighting the way try_then_request_module() works, simply open code what we want to happen in a local helper function. Signed-off-by:
David S. Miller <davem@davemloft.net>
-
David S. Miller authored
The return value isn't used. Suggested by Ben Hucthings. Signed-off-by:
David S. Miller <davem@davemloft.net>
-
David S. Miller authored
This reverts commit 81d54ec8 . If we take the "try_again" goto, due to a checksum error, the 'len' has already been truncated. So we won't compute the same values as the original code did. Reported-by:
paul bilke <fsmail@conspiracy.net> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Vitalii Demianets authored
When in user-stp mode, bridge master do not follow state of its slaves, so after the following sequence of events it can stuck forever in no-carrier state: 1) turn stp off 2) put all slaves down - master device will follow their state and also go in no-carrier state 3) turn stp on with bridge-stp script returning 0 (go to the user-stp mode) Now bridge master won't follow slaves' state and will never reach running state. This patch solves the problem by making user-stp and kernel-stp behavior similar regarding master following slaves' states. Signed-off-by:
Vitalii Demianets <vitas@nppfactor.kiev.ua> Acked-by:
Stephen Hemminger <shemminger@vyatta.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
David S. Miller authored
Otherwise we won't notice the peer GENID change. Reported-by:
Steffen Klassert <steffen.klassert@secunet.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Eric Dumazet authored
gcc compiler is smart enough to use a single load/store if we memcpy(dptr, sptr, 8) on x86_64, regardless of CONFIG_CC_OPTIMIZE_FOR_SIZE In IP header, daddr immediately follows saddr, this wont change in the future. We only need to make sure our flowi4 (saddr,daddr) fields wont break the rule. Signed-off-by:
Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
David S. Miller authored
This also works around a bogus gcc warning generated by an upcoming patch from Eric Dumazet that rearranges the layout of struct flowi4. Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Wolfgang Grandegger authored
This patch enables or updates support for the CC770 and AN82527 CAN controller on the TQM8548 and TQM8xx boards. CC: devicetree-discuss@lists.ozlabs.org CC: linuxppc-dev@ozlabs.org CC: Kumar Gala <galak@kernel.crashing.org> Signed-off-by:
Wolfgang Grandegger <wg@grandegger.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Wolfgang Grandegger authored
This driver works with both, static platform data and device tree bindings. It has been tested on a TQM855L board with two AN82527 CAN controllers on the local bus. CC: Devicetree-discuss@lists.ozlabs.org CC: linuxppc-dev@ozlabs.org CC: Kumar Gala <galak@kernel.crashing.org> Signed-off-by:
Wolfgang Grandegger <wg@grandegger.com> Acked-by:
Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Wolfgang Grandegger authored
This patch adds support for legacy Bosch CC770 and Intel AN82527 CAN controllers on the ISA or PC-104 bus. The I/O port or memory address and the IRQ number must be specified via module parameters: insmod cc770_isa.ko port=0x310,0x380 irq=7,11 for ISA devices using I/O ports or: insmod cc770_isa.ko mem=0xd1000,0xd1000 irq=7,11 for memory mapped ISA devices. Indirect access via address and data port is supported as well: insmod cc770_isa.ko port=0x310,0x380 indirect=1 irq=7,11 Furthermore, the following mode parameter can be defined: clk: External oscillator clock frequency (default=16000000 [16 MHz]) cir: CPU interface register (default=0x40 [DSC]) bcr: Bus configuration register (default=0x40 [CBY]) cor: Clockout register (default=0x00) Note: for clk, cir, bcr and cor, the first argument re-defines the default for all other devices, e.g.: insmod cc770_isa.ko mem=0xd1000,0xd1000 irq=7,11 clk=24000000 is equivalent to insmod cc770_isa.ko mem=0xd1000,0xd1000 irq=7,11 clk=24000000,24000000 Signed-off-by:
Wolfgang Grandegger <wg@grandegger.com> Acked-by:
Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Wolfgang Grandegger authored
Signed-off-by:
Wolfgang Grandegger <wg@grandegger.com> Acked-by:
Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Patrick Kelle authored
At this point the variable j is always set to 7 and the code within the loop has to run only once anyway. As suggested by David Miller: "You can simply this even further since p[7] is what is used here, and this means len is one, the inner loop therefore executes only once, and the p[7].field value is not used (it's zero in the table) and the write to it is completely thrown away." Signed-off-by:
Patrick Kelle <patrick.kelle81@gmail.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Eric Dumazet authored
commit b00055aa ([NET] core: add RFC2863 operstate) changed net_device flags from unsigned short to unsigned int. Some core functions still assume its an unsigned short. Signed-off-by:
Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Axel Lin authored
Include linux/if_ether.h to fix below build errors: CC arch/arm/mach-kirkwood/common.o In file included from arch/arm/mach-kirkwood/common.c:19: include/net/dsa.h: In function 'dsa_uses_dsa_tags': include/net/dsa.h:192: error: 'ETH_P_DSA' undeclared (first use in this function) include/net/dsa.h:192: error: (Each undeclared identifier is reported only once include/net/dsa.h:192: error: for each function it appears in.) include/net/dsa.h: In function 'dsa_uses_trailer_tags': include/net/dsa.h:197: error: 'ETH_P_TRAILER' undeclared (first use in this function) make[1]: *** [arch/arm/mach-kirkwood/common.o] Error 1 make: *** [arch/arm/mach-kirkwood] Error 2 Signed-off-by:
Axel Lin <axel.lin@gmail.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Eric Dumazet authored
ERROR: "__udivdi3" [net/sched/sch_netem.ko] undefined! Signed-off-by:
Eric Dumazet <eric.dumazet@gmail.com> Acked-by:
Hagen Paul Pfeifer <hagen@jauu.net> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfsLinus Torvalds authored
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs: Btrfs: fix meta data raid-repair merge problem Btrfs: skip allocation attempt from empty cluster Btrfs: skip block groups without enough space for a cluster Btrfs: start search for new cluster at the beginning Btrfs: reset cluster's max_size when creating bitmap Btrfs: initialize new bitmaps' list Btrfs: fix oops when calling statfs on readonly device Btrfs: Don't error on resizing FS to same size Btrfs: fix deadlock on metadata reservation when evicting a inode Fix URL of btrfs-progs git repository in docs btrfs scrub: handle -ENOMEM from init_ipath()
-
- Dec 01, 2011
-
-
Jan Schmidt authored
Commit 4a54c8c1 introduced raid-repair, killing the individual readpage_io_failed_hook entries from inode.c and disk-io.c. Commit 4bb31e92 introduced new readahead code, adding a readpage_io_failed_hook to disk-io.c. The raid-repair commit had logic to disable raid-repair, if readpage_io_failed_hook is set. Thus, the readahead commit effectively disabled raid-repair for meta data. This commit changes the logic to always attempt raid-repair when needed and call the readpage_io_failed_hook in case raid-repair fails. This is much more straight forward and should have been like that from the beginning. Signed-off-by:
Jan Schmidt <list.btrfs@jan-o-sch.net> Reported-by:
Stefan Behrens <sbehrens@giantdisaster.de> Signed-off-by:
Chris Mason <chris.mason@oracle.com>
-
RongQing.Li authored
Within nested statements, the break statement terminates only the do, for, switch, or while statement that immediately encloses it, So replace the break with goto. Signed-off-by:
RongQing.Li <roy.qing.li@gmail.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
sjur.brandeland@stericsson.com authored
Signed-off-by:
Sjur Brændeland <sjur.brandeland@stericsson.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
sjur.brandeland@stericsson.com authored
Remove unused enum cfcnfg_phy_type and the parameter to cfserl_create. Signed-off-by:
Sjur Brændeland <sjur.brandeland@stericsson.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
sjur.brandeland@stericsson.com authored
Enrolling CAIF link layers are refactored. Signed-off-by:
Sjur Brændeland <sjur.brandeland@stericsson.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
sjur.brandeland@stericsson.com authored
Allow NULL pointer in cfpkt_extr_head in order to skip past header data. Signed-off-by:
Sjur Brændeland <sjur.brandeland@stericsson.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Eric Dumazet authored
Since commit a4a710c4 (pkt_sched: Change PSCHED_SHIFT from 10 to 6) it seems RED/GRED are broken. red_calc_qavg_from_idle_time() computes a delay in us units, but this delay is now 16 times bigger than real delay, so the final qavg result smaller than expected. Use standard kernel time services since there is no need to obfuscate them. Signed-off-by:
Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Hagen Paul Pfeifer authored
Currently netem is not in the ability to emulate channel bandwidth. Only static delay (and optional random jitter) can be configured. To emulate the channel rate the token bucket filter (sch_tbf) can be used. But TBF has some major emulation flaws. The buffer (token bucket depth/rate) cannot be 0. Also the idea behind TBF is that the credit (token in buckets) fills if no packet is transmitted. So that there is always a "positive" credit for new packets. In real life this behavior contradicts the law of nature where nothing can travel faster as speed of light. E.g.: on an emulated 1000 byte/s link a small IPv4/TCP SYN packet with ~50 byte require ~0.05 seconds - not 0 seconds. Netem is an excellent place to implement a rate limiting feature: static delay is already implemented, tfifo already has time information and the user can skip TBF configuration completely. This patch implement rate feature which can be configured via tc. e.g: tc qdisc add dev eth0 root netem rate 10kbit To emulate a link of 5000byte/s and add an additional static delay of 10ms: tc qdisc add dev eth0 root netem delay 10ms rate 5KBps Note: similar to TBF the rate extension is bounded to the kernel timing system. Depending on the architecture timer granularity, higher rates (e.g. 10mbit/s and higher) tend to transmission bursts. Also note: further queues living in network adaptors; see ethtool(8). Signed-off-by:
Hagen Paul Pfeifer <hagen@jauu.net> Acked-by:
Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by:
David S. Miller <davem@drr.davemloft.net>
-
Jun Zhao authored
Need not to used 'delta' flag when add single-source to interface filter source list. Signed-off-by:
Jun Zhao <mypopydev@gmail.com> Signed-off-by:
David S. Miller <davem@drr.davemloft.net>
-