This patch adds support for the new copper device X557.

Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

This shouldn't matter as nothing should be attached still to be
consisted control MDIO speed for these devices as well.

Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

The X557 devices use a different interface to the LED for the port.
This patch reflect that change.

Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Add geneve Rx offload support for x550em_a.

The implementation follows the vxlan code with the lower 16 bits of
the VXLANCTRL register holding the UDP port for VXLAN and the upper
for Geneve.

Disabled NFS filters in the RFCTL register which allows us to simplify
the check for VXLAN and Geneve packets in ixgbe_rx_checksum().

Removed vxlan from the name of the callback functions and replaced it
with udp_tunnel which is more in line with the new API.

Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

The PF driver was only receiving the first 4 bytes of the MAC due
to an incorrect size parameter for ixgbevf_write_msg_read_ack()
in ixgbevf_set_rar_vf().

Correct the size by calculating it on a fly for all instances where
we call ixgbevf_write_msg_read_ack()

Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

ethtool reports backplane type interfaces as 1000/10000baseT link modes.
This has been corrected to report the media as KR, KX or KX4 based on the backplane interface present.

Signed-off-by: Veola Nazareth <veola.nazareth@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Markus Elfring says:

====================
tun: Fine-tuning for update_filter()

A few update suggestions were taken into account
from static source code analysis.
====================

Signed-off-by: David S. Miller <davem@davemloft.net>

Adjust a jump target according to the Linux coding style convention.

Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

Reuse existing functionality from memdup_user() instead of keeping
duplicate source code.

This issue was detected by using the Coccinelle software.

Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Reviewed-by: Shmulik Ladkani <shmulik.ladkani@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Jeff Kirsher says:

====================
40GbE Intel Wired LAN Driver Updates 2016-08-19

This series contains updates to i40e and i40evf only.

Jake provides several patches, first just moves a function to co-locate
the two functions related to configuring RSS via the admin queue, which
should help in spotting bugs when comparing the two functions.  Fixed
an issue where commit e69ff813

 ("i40e: rework the functions to
configure RSS with similar parameters") missed checking whether the seed
is NULL before using it and did not use the passed in *lut parameter.
Fixed an issue where a previous refactor missed i40e_vsi_config_rss()
and the values were being ignored, so checked for the fields and used
them instead of default values.  Lastly replaced calls to
create_singlethread_workqueue() with alloc_workqueue() to provide more
control over workqueue creation and allows explicit setting of the
desired mode of operation.

Mitch adds link speed to log messages and reports speed through ethtool.

Carolyn refactors tail bump check and fixes byte ordering problems found
when enabling this feature support.  Adds support for HMC resources and
profile commands for x722 firmware.

Heinrich Schuchardt fixes format identifiers from %u to %d since the
variable is defined as an integer.

Catherine fixes an issue where there was a race condition between the
completion of the client open and calls to the client ops, so ensured
that client ops are not called until we are sure client is open.

Harshitha makes sure that i40e_client_release() does not try to use
an adapter pointer which may not be initialized, so make sure it is.

Joe Perches fixes the use of the local macro XSTRINGIFY() to use
__stringify() instead.

Avinash corrects the mutex usage in client_subtask().  Fixed the RDMA
client to open again after reset since it is closed during a PF reset.

Jeff (me) clean up whitespace issues, where indentation was done
inconsistently and with spaces versus tabs.
====================

Signed-off-by: David S. Miller <davem@davemloft.net>

The patch creates sample code exercising bpf_skb_{set,get}_tunnel_key,
and bpf_skb_{set,get}_tunnel_opt for GRE, VXLAN, and GENEVE.  A native
tunnel device is created in a namespace to interact with a lwtunnel
device out of the namespace, with metadata enabled.  The bpf_skb_set_*
program is attached to tc egress and bpf_skb_get_* is attached to egress
qdisc.  A ping between two tunnels is used to verify correctness and
the result of bpf_skb_get_* printed by bpf_trace_printk.

Signed-off-by: William Tu <u9012063@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The existing code uses busy retry when unable to send out receive
completions due to full ring buffer. It also gives up retrying after limit
is reached, and causes receive buffer slots not being recycled.
This patch implements batching of receive completions. It also prevents
dropping receive completions due to full ring buffer.

Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Reviewed-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

RDMA client is closed during the PF reset and needs to be opened again.
Setting the flag so that RDMA client is opened in watchdog() function.

Change-ID: I507b1e4cbd05528cdff68fd360ef3dcac8901263
Signed-off-by: Avinash Dayanand <avinash.dayanand@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Several defines and code comments were indented with spaces instead
of tabs, correct the issue to make indentation consistent.

Change-ID: I0dc6bbb990ec4a9e856acc9ec526d876181f092c
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>

Correcting the mutex usage, in client_subtask(), mutex_unlock has
to be called just before client_del_instance() since this function opens
and later closes the same mutex again.
Similarly in client_is_registered removing the mutex since it closes
the mutex twice.

This is a patch suggested by RDMA team.

Change-ID: Icce519c266e4221b8a2a72a15ba5bf01750e5852
Signed-off-by: Avinash Dayanand <avinash.dayanand@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Use __stringify instead.

Signed-off-by: Joe Perches <joe@perches.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

The function i40e_client_release has a print statement that uses an
adapter pointer which is not initialized if a previous if statement
is not true. Hence, intialize it in the right place.

Change-ID: I1afdaa2c46771ac42be56edcc41bb56b455b06c8
Signed-off-by: Harshitha Ramamurthy <harshitha.ramamurthy@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

We were having a race between the completion of the client open and
calls to the client ops so don't call a client op unless we are sure the
client is open.

Testing Hints: Load IWARP driver and make sure it works as expected.

Change-Id: I741f4f2aa4fcbfdad3e40dabbbb1b005856c396b
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

i is defined as int but output as %u several times.
Adjust the format identifiers.

Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch adds support for HMC resource and profile cmds for X722
firmware.

Change-ID: Icc332101f38ab15d1bfa167823100eb4f6822f7e
Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch fixes byte ordering problems found when enabling this feature
support. Without this patch, the feature will not work correctly. This
patch fixes the definitions to have the correct byte order.

Change-ID: Ic7489fbcbe2195df7be62ff5e359201b827cefe6
Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch refactors tail bump check.

Change-ID: Ide0e19171d67d90cb2b06b8dcd4fa791ae120160
Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

The PF driver tells us the link speed, so do something with that
information. Add link speed to log messages, and report speed through
ethtool.

Change-Id: I279dc9540cc5203376406050a3e8d67e128d5882
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Replace calls to create_singlethread_workqueue instead with alloc_workqueue
as is style with other Intel drivers. This provides more control over
workqueue creation, and allows explicit setting of the desired mode of
operation. It also makes it more obvious that driver name constant is
passed to a format "%s".

Change-ID: I6192b44caf5140336cd54c5b350d51c73b541fdb
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

A previous refactor added support to store user configuration for VSIs,
so that extra VSIs such as for VMDq can use this information when
configuring. Unfortunately the i40e_vsi_config_rss function was missed
in this refactor, and the values were being ignored. Fix this by
checking for the fields and using those instead of always using the
default values.

Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

X722 hardware requires using the admin queue to configure RSS. This
function was previously re-written in commit e69ff813 ("i40e: rework
the functions to configure RSS with similar parameters").
However, the previous refactor did not work correctly for a few reasons

(a) it does not check whether seed is NULL before using it, resulting in
a NULL pointer dereference

[  402.954721] BUG: unable to handle kernel NULL pointer dereference at           (null)
[  402.955568] IP: [<ffffffffa0090ccf>] i40e_config_rss_aq.constprop.65+0x2f/0x1c0 [i40e]
[  402.956402] PGD ad610067 PUD accc0067 PMD 0
[  402.957235] Oops: 0000 [#1] SMP
[  402.958064] Modules linked in: ip6t_rpfilter ip6t_REJECT nf_reject_ipv6 xt_conntrack ip_set nfnetlink ebtable_filter ebtable_
broute bridge stp llc ebtable_nat ebtables ip6table_mangle ip6table_raw ip6table_nat nf_conntrack_ipv6 nf_defrag_ipv6 nf_nat_ipv
6 ip6table_security ip6table_filter ip6_tables iptable_mangle iptable_raw iptable_nat nf_conntrack_ipv4_ nf_defrag_ipv4_ nf_nat_ip
v4_ nf_nat nf_conntrack iptable_security intel_rapl i86_kg_temp_thermal coretemp kvm_intel kvm irqbypass crct10dif_clMl crc32_
pclMl ghash_clMlni_intel iTCO_wdt iTCO_vendor_support shpchp sb_edac dcdbas pcspkr joydev ipmi_devintf wmi edac_core ipmi_ssif
 acpi_ad acpi_ower_meter ipmi_si ipmi_msghandler mei_me nfsd lpc_ich mei ioatdma tpm_tis auth_rpcgss tpm nfs_acl lockd grace s
unrpc ifs nngag200 i2c_algo_bit drm_kms_helper ttm drm iigbe bnx2x i40e dca mdio ptp pps_core libcrc32c fjes crc32c_intel
[  402.965563] CPU: 22 PID: 2461 Conm: ethtool Not tainted 4.6.0-rc7_1.2-ABNidQ+ #20
[  402.966719] Hardware name: Dell Inc. PowerEdge R720/0C4Y3R, BIOS 2.5.2 01/28/2015
[  402.967862] task: ffff880219b51dc0 ti: ffff8800b3408000 task.ti: ffff8800b3408000
[  402.969046] RIP: 0010:[<ffffffffa0090ccf>]  [<ffffffffa0090ccf>] i40e_config_rss_aq.constprop.65+0x2f/0x1c0 [i40e]
[  402.970339] RSP: 0018:ffff8800b340ba90  EFLAGS: 00010246
[  402.971616] RAX: 0000000000000000 RBX: ffff88042ec14000 RCX: 0000000000000200
[  402.972961] RDX: ffff880428eb9200 RSI: 0000000000000000 RDI: ffff88042ec14000
[  402.974312] RBP: ffff8800b340baf8 R08: ffff880237ada8f0 R09: ffff880428eb9200
[  402.975709] R10: ffff880428eb9200 R11: 0000000000000000 R12: ffff88042ec2e000
[  402.977104] R13: ffff88042ec2e000 R14: ffff88042ec14000 R15: ffff88022ea00800
[  402.978541] FS:  00007f84fd054700(0000) GS:ffff880237ac0000(0000) knlGS:0000000000000000
[  402.980003] CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[  402.981508] CR2: 0000000000000000 CR3: 000000003289e000 CR4: 00000000000406e0
[  402.983028] Stack:
[  402.984578]  0000000002000200 0000000000000000 ffff88023ffeda68 ffff88023ffef000
[  402.986187]  0000000000000268 ffff8800b340bbf8 ffff88023ffedd80 0000000088ce4f1d
[  402.987844]  ffff88042ec14000 ffff88022ea00800 ffff88042ec2e000 ffff88042ec14000
[  402.989509] Call Trace:
[  402.991200]  [<ffffffffa009636f>] i40e_config_rss+0x11f/0x1c0 [i40e]
[  402.992924]  [<ffffffffa00a1ae0>] i40e_set_rifh+0ic0/0x130 [i40e]
[  402.994684]  [<ffffffff816d54b7>] ethtool_set_rifh+0x1f7/0x300
[  402.996446]  [<ffffffff8136d02b>] ? cred_has_capability+0io6b/0x100
[  402.998203]  [<ffffffff8136d102>] ? selinux_capable+0x12/0x20
[  402.999968]  [<ffffffff8136277b>] ? security_capable+0x4b/0x70
[  403.001707]  [<ffffffff816d6da3>] dev_ethtool+0x1423/0x2290
[  403.003461]  [<ffffffff816eab41>] dev_ioctl+0x191/0io630
[  403.005186]  [<ffffffff811cf80a>] ? lru_cache_add+0x3a/0i80
[  403.006942]  [<ffffffff817f2a8e>] ? _raw_spin_unlock+0ie/0x20
[  403.008691]  [<ffffffff816adb95>] sock_do_ioctl+0x45/0i50
[  403.010421]  [<ffffffff816ae229>] sock_ioctl+0x209/0x2d0
[  403.012173]  [<ffffffff81262194>] do_vfs_ioctl+0u4/0io6c0
[  403.013911]  [<ffffffff81262829>] SyS_ioctl+0x79/0x90
[  403.015710]  [<ffffffff817f2e72>] entry_SYSCALL_64_fastpath+0x1a/0u4
[  403.017500] Code: 90 55 48 89 e5 41 57 41 56 41 55 41 54 53 48 89 fb 48 83 ec 40 4c 8b a7 e0 05 00 00 65 48 8b 04 25 28 00 00 00 48 89 45 d0 31 c0 <48> 8b 06 41 0f b7 bc 24 f2 0f 00 00 48 89 45 9c 48 8b 46 08 48
[  403.021454] RIP  [<ffffffffa0090ccf>] i40e_config_rss_aq.constprop.65+0x2f/0x1c0 [i40e]
[  403.023395]  RSP <ffff8800b340ba90>
[  403.025271] CR2: 0000000000000000
[  403.027169] ---[ end trace 64561b528cf61cf0 ]---

(b) it does not even bother to use the passed in *lut parameter which
defines the requested lookup table. Instead it uses its own round robin
table.

Fix these issues by re-writing it to be similar to i40e_config_rss_reg
and i40e_get_rss_aq.

Fixes: e69ff813

 ("i40e: rework the functions to configure RSS with similar parameters", 2015-10-21)
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Move this function below the two functions related to configuring RSS
via the admin queue. This helps co-locate the two functions, and made it
easier to spot a bug in the first i40e_config_rss_aq function as
compared to the i40e_get_rss_aq function.

Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

We've already set sk to sock->sk and dereferenced it, so if it's NULL
we would have crashed already. Moreover, if it was NULL we would have
crashed anyway when jumping to 'out' and trying to unlock the sock.
Furthermore, if we had assigned a different value to 'sk' we would
have been calling lock_sock() and release_sock() on different sockets.

My conclusion is that these two lines are complete nonsense and only
serve to confuse the reader.

Signed-off-by: Vegard Nossum <vegard.nossum@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This new firmware for the qed* adpaters fixes several issues:
 - Better blocking of malicious VFs.
 - After FLR, Tx-switching [internal routing] of packets might
   be incorrect.
 - Deletion of unicast MAC filters would sometime have side-effect
   of corrupting the MAC filters configred for a device.
It also contains fixes for future qed* drivers that *hopefully* would be
sent for review in the near future.

In addition, it would allow driver some new functionality, including:
 - Allowing PF/VF driver compaitibility with old drivers [running
   pre-8.10.5.0 firmware].
 - Better debug facilities.

This would also bump the qed* driver versions to 8.10.9.20.

Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Jeff Kirsher says:

====================
10GbE Intel Wired LAN Driver Updates 2016-08-18

This series contains updates to ixgbe and ixgbevf.

Emil cleans up confusing amongst the users by making an error message
into a debug message, since the TXDCTL.ENABLE (and comparable
VFTXDCTL.ENABLE for ixgbevf) bit is set only when the
transmit queue is actually enabled, which may not happen during the
configure phase eve if we waited for it.  Converts to using netdev_dbg()
macro instead of our home brewed macro for ixgbevf.  Converted the
service task to use atomic bitwise operations when setting and checking
reset requests to reduce the possibility of race conditions.
====================

Signed-off-by: David S. Miller <davem@davemloft.net>

Florian Fainelli says:

====================
net: dsa: bcm_sf2: Platform conversion

This patch series converts the bcm_sf2 driver from a traditional DSA driver
into a platform_device driver and makes it use the new DSA binding that Andrew
introduced in the latest merge window.

Prior attempts used to coerce the code in net/dsa/dsa2.c to accept the old
binding, while really there is only one broken single user out there: bcm_sf2,
so instead, just assume the new DT binding is deployed and use it accordingly.
====================

Signed-off-by: David S. Miller <davem@davemloft.net>

Remove our dsa_switch_driver::drv_probe callback to prevent probing
through the old DSA binding, not that this could happen anymore now that
we have moved the matching compatible string from net/dsa/dsa.c to
drivers/net/dsa/bcm_sf2.c, so this is essentially dead code.

Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Now that we have converted the drivers into a proper platform device
driver, we can use the device managed helper functions to simplify the
error paths a bit wrt. register resources and IRQs.

Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The Broadcom Starfighter 2 switch driver should be a proper platform
driver, now that the DSA code has been updated to allow that, register a
switch device, feed it with the proper configuration data coming from
Device Tree and register our switch device with DSA.

The bulk of the changes consist in moving what bcm_sf2_sw_setup() did
into the platform driver probe function.

Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Document the updated binding which conforms to the new DSA binding in
net/dsa/dsa.txt.

Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In preparation for allowing switch drivers to implement system-wide
suspend/resume functions, export dsa_switch_suspend and
dsa_switch_resume() such that these are callable from the appropriate
driver specific suspend/resume functions.

Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Andrew Lunn says:

====================
Fix mv88e6xxx wait function

The mv88e6xxx wait function can be upset of the system has nots of
other things to do and a sleep takes a lot longer than expected. Fix
this be using a fixed number of iterations, rather than a fixed
walkclock time.

Witht that change made, it is possible to consoliate another
wait function.

A wait actually timing out should not happen and when it does, it
means something serious is wrong. Make sure an error is logged,
since not all callers will log an error.
====================

Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When mv88e6xxx_wait() returns a timeout, something bad has
happened. Make sure it is noticed by logging an error.

Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

Now that mv88e6xx_wait() iterated on a counter than a fixed time
interval, it implements the same mechanism as mv88e6xxx_update() uses.
So use it in mv88e6xx_wait().

Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

The mv88e6xxx driver times out operations on the switch based on
looping until an elapsed wall clock time is reached. However, if
usleep_range() sleeps much longer than expected, it could timeout with
an error without actually checking to see if the devices has completed
the operation. So replace the elapsed time with a fixed upper bound on
the number of loops.

Testing on various switches has shown that switches takes either 0 or
1 iteration, so a maximum of 16 iterations is a safe limit.

Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>