The implementation hardcodes a workaround for the H3 ES1.x SoC
regardless of the SoC revision, as the workaround can be safely applied
on all devices in the Gen3 family without any side effect.

Signed-off-by: Koji Matsuoka <koji.matsuoka.xm@renesas.com>
Signed-off-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>

When a DT node connected to a DU output is disabled no bridge will ever
be instantiated for it. Skip the output in that case.

Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>

The R-Car Gen3 SoCs include on-chip DesignWare HDMI encoders. Support
them with a platform driver to provide platform glue data to the dw-hdmi
driver.

The driver is a complete rewrite of code coming from the Renesas BSP,
save for the values in the PHY parameters table.

Signed-off-by: Koji Matsuoka <koji.matsuoka.xm@renesas.com>
Signed-off-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>

The Renesas R-Car Gen3 SoCs use a Synopsys DWC HDMI TX encoder IP. Add
corresponding device tree bindings based on the DWC HDMI TX bindings
model.

Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Rob Herring <robh@kernel.org>

Unlike the connector type, the encoder type is unused by userspace. As
it is equally unused in the driver, except in a single location where
the connector type can be used instead, hardcode it to
DRM_MODE_ENCODER_NONE. This allow removing all code that tries to
determine (unsuccessfully in case a bridge is used) the encoder type.

Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>

The rcar-du driver contains a manual implementation of HDMI and VGA
bridges. Use DRM bridges to replace it.

Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>

Retrieve the LVDS mode from the panel and configure the LVDS encoder
accordingly. LVDS mode selection is static as LVDS panels can't be
hot-plugged on any of the device supported by the driver. Support for
dynamic mode selection can be implemented in the future when needed.

Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>

Instead of parsing the panel device tree node manually, use the panel
API to delegate panel handling to a panel driver.

Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>

The property is used by the driver but is missing from the DT bindings.
Document it.

Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>

The field is a left-over from the switch to the atomic commit helper.
It's unused, remove it.

Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>

On Gen3 platforms planes are managed by the external VSP compositor on
behalf of DRM/KMS. If VSP compositor support is not enabled in the DU
driver, the VSP initialization stub routine is called. Return an error
from that stub to fail explicitly, otherwise the device won't be usable
and the driver will crash.

Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
[Clarified commit message]
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>

The DRM core atomic helper now supports asynchronous commits natively.
The custom rcar-du implementation isn't needed anymore, remove it.

Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>

The atomic commit helper requires drivers to clear the event pointer
stored in the CRTC state when the event is handled. In preparation to
using the helper, fix the driver.

Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>

The driver currently handles vblank events only when updating planes on
a CRTC. The atomic update API however allows requesting an event when
disabling a CRTC. This currently leads to event objects being leaked in
the kernel and to events not being sent out. Fix it.

Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>

This change will also make Coverity happy by avoiding a theoretical NULL
pointer dereference; yet another reason is to use the above helper function
to tighten the code and make it more readable.

Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Tested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>

The native encoder mode set helper function for atomic drivers is
.atomic_mode_set(). Replace the legacy .mode_set() implementation.

Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>

This driver supports LVDS panels that don't require device-specific
handling of power supplies or control signals. It implements automatic
backlight handling if the panel is attached to a backlight controller.

Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>

The flags indicate whether data is transmitted LSB to MSB or MSB to LSB
on the bus.

The exact meaning is bus-type dependent. For instance, for LVDS buses
the flags indicate whether the seven data bits transmitted in a clock
pulse are sent in normal order (MSB to LSB, slots 0 to 6) or reverse
order (LSB to MSB, slots 6 to 0).

Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>

The AA104XD12 and AA121TD01 are LVDS display panels. Their bindings are
modelled on the the LVDS panel bindings.

Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Rob Herring <robh@kernel.org>

LVDS is a physical layer specification defined in ANSI/TIA/EIA-644-A.
Multiple incompatible data link layers have been used over time to
transmit image data to LVDS panels. This binding supports display panels
compatible with the JEIDA-59-1999, Open-LDI and VESA SWPG
specifications.

Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Rob Herring <robh@kernel.org>

Document properties common to several display panels in a central
location that can be referenced by the panel device tree bindings.

Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Rob Herring <robh@kernel.org>

omapdrm changes for 4.12

Main changes include:

* Add support for render nodes.
* Refactor omapdss code to allow multiple DISPC implementations. This is pre-work for DSS6 support.
* Fix replication logic bug, which caused RGB565 fb to be shown too dark on a 24bit display.
* Improve detection of display stack readiness, which should remove the probe order issues.
* Link panel-dpi with its backlight, so that they are turned on/off in sync.
* Fix possibly incorrect setup of sync and data-enable signals.
* Get rid of DRM_OMAP_NUM_CRTCS config option.

* tag 'omapdrm-4.12' of git://git.kernel.org/pub/scm/linux/kernel/git/tomba/linux: (34 commits)
  drm/omap: Major omap_modeset_init() cleanup
  drm/omap: Remove the obsolete #define omap_plane _omap_plane hack
  drm/omap: Fix one ugly indentation style break left by coccinelle
  drm/omap: Rename enum omap_plane to enum omap_plane_id
  drm/omap: Get rid of DRM_OMAP_NUM_CRTCS config option
  drm/omap: fix crash on module unload
  drm/omap: use drm_atomic_helper_shutdown()
  drm/omap: fix display SYNC/DE flags
  drm/omap: dispc: improve debug print of display flags
  drm/omap: displays: panel-dpi: Support for handling backlight devices
  drm/omap: poll only connectors where the connect/disconnect can be checked
  drm/omap: display: Add displays in sorted order to the panel_list
  drm/omap: Use omapdss_stack_is_ready() to check that the display stack is up
  drm/omap: dss: Support for detecting display stack readiness
  drm/omap: dss: Functions to check components in the display/output list
  drm/omap: fix replication logic
  drm/omap: remove unused dispc_wb_enable & dispc_wb_is_enabled
  drm/omap: remove all EXPORT_SYMBOLs from dispc.c
  drm/omap: use dispc_ops
  drm/omap: fill dispc_ops
  ...

Cleanup overly complex omap_modeset_init(). The function is trying to
support many unusual configuration, that have never been tested and
are not supported by other parts of the dirver.

After cleanup the init function creates exactly one connector,
encoder, crtc, and primary plane per each connected dss-device. Each
connector->encoder->crtc chain is expected to be separate and each
crtc is connect to a single dss-channel. If the configuration does not
match the expectations or exceeds the available resources, the
configuration is rejected.

Signed-off-by: Jyri Sarha <jsarha@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>

Remove the obsolete "#define omap_plane _omap_plane" hack and other
related hacks to get around the enum omap_plane colliding with struct
omap_plane.

Signed-off-by: Jyri Sarha <jsarha@ti.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>

Fix one ugly indentation style break left by the previous coccilnelle
patch.

Signed-off-by: Jyri Sarha <jsarha@ti.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>

The enum omap_plane conflicted with the same struct name for omapdrm
plane private data. This rename should solve the conflict.

The rename was implement with this very simple coccinelle patch:
------------------------
@@
@@
enum
-omap_plane
+omap_plane_id
------------------------
The patch was applied like this:
spatch --sp-file <cocci_file> --all-includes --in-place --dir drivers/gpu/drm/omapdrm

The above patch did not rename the actual enum definition. That was
added manually on top of the spatch changes.

Signed-off-by: Jyri Sarha <jsarha@ti.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>

Allocate one CRTC for each connected output and get rid of
DRM_OMAP_NUM_CRTCS config option. We still can not create more CRTCs
than we have DSS display managers. We also reserve one overlay per
CRTC for primary plane so we can not have more CRTCs than we have
overlays either.

Signed-off-by: Jyri Sarha <jsarha@ti.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>

When unloading omapdrm we get a NULL pointer deref in
omap_drm_irq_uninstall(). This is caused by:

967dd484

 ("drm: remove
drm_vblank_no_hw_counter assignment from driver code")

We shut down all the crtcs at unload time before calling
omap_drm_irq_uninstall, so the code in omap_drm_irq_uninstall() is
unnecessary and can be removed.

Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>

Use drm_atomic_helper_shutdown() to ensure that all crtcs are disabled
when unloading the driver.

Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>

At the moment VSYNC/HSYNC/DE high/low flags set by the panel/encoder
drivers get lost when the videotimings are translated to DRM's
videomode, as DRM's mode does not have corresponding flags.

DRM has bus-flags for this purpose, and while it lacks a few flags at
the moment, it should be used here. However, until we rewrite omapdrm's
device model, using bus-flags is rather difficult.

As a short term fix, this patch makes sure that every time the videomode
is set in omap_crtc_mode_set_nofb(), the driver asks for the SYNC/DE
flags from the panel/encoder drivers, and thus we get the correct flags
into use.

Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>

Instead of printing 0/1 for display flags like vsync high/low, use a
tri-state print (-1/0/1) to indicate the "undefined" state.

Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>

The associated backlight device can be configured via DT by providing the
phandle to the device.

If the backlight device is configured, the driver can manage the backligt
along with the panel's power state, iow it can turn on the backlight when
the panel is enabled and turn it off when the panel is disabled.

Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>

When the connector associated detect callback is not provided, we can not
detect if the display is connected or disconnected. These displays do not
support hot plug, they are always connected. Let DRM know that connectors
w/o detect callback should not be polled.

Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>

Keep the panel_list ordered according to aliases. The DRM connectors will
be created following the panel_list. By keeping the list ordered the DRM
connectors will be created in the same order regardless of the driver
probe order.

Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>

Instead of 'guessing' based on aliases of the status of the DSS drivers,
use the new interface to check that all needed drivers are loaded.
In this way we can be sure that all needed drivers are loaded so it is
safe to continue the probing of omapdrm.
This method will allow the omapdrm to be probed 'headless', without
outputs.

Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>

When omapdss is loaded (all core components are in place) create a list of
devices used in the display graph. This list later can be used by omapdrm
via the omapdss_stack_is_ready() function to check that these components
are loaded. Based on this information, omapdrm can defer probe in case when
the omapdss stack is not ready yet.

Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>

The functions can be used to check a component (by it's of_node) if it is
part of the omapdss display or output list. If the component is found, it
means that the driver is loaded.

Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>

DSS uses "replication logic" to convert color components from smaller
bit widths to bigger bit widths. Without replication logic, the color
component would be shifted and the least significant bits would be left
at 0, whereas with replication logic, the least significat bits will be
filled with the most significant bit.

For some reason omapdrm leaves replication logic always to off, which,
in the most common case, means that showing 16-bit RGB colors on 24-bit
display gives a bit darker colors than expected.

The reset value of the replication logic bit is enabled, and it should
always be set, as there's no practical reason to disable it. This patch
removes the option to disable it from omapdrm, and always sets it to
enabled in dispc.

Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>

Remove two unused WB functions.

Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>

omapdrm now uses dispc_ops instead of direct function calls so we can
remove all EXPORT_SYMBOLs from dispc. Most of the functions can also be
made static, but a few are used outside dispc.c.

Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>