Raju Rangoju says:

====================
amd-xgbe: add support for 2.5GbE and rx-adaptation

This patch series adds support for 2.GbE in 10GBaseT mode and
rx-adaptation support for Yellow Carp devices.

1) Support for 2.5GbE:
   Add the necessary changes to the driver to fully recognize and enable
   2.5GbE speed in 10GBaseT mode.

2) Support for rx-adaptation:
   In order to support the 10G backplane mode without Auto-negotiation
   and to support the longer-length DAC cables, it requires PHY to
   perform RX Adaptation sequence as mentioned in the Synopsys databook.
   Add the necessary changes to Yellow Carp devices to ensure seamless
   RX Adaptation for 10G-SFI (LONG DAC), and 10G-KR modes without
   Auto-Negotiation (CL72 not present)
====================

Link: https://lore.kernel.org/r/20230201054932.212700-1-Raju.Rangoju@amd.com


Signed-off-by: Paolo Abeni <pabeni@redhat.com>

The existing implementation for non-Autonegotiation 10G speed modes does
not enable RX adaptation in the Driver and FW. The RX Equalization
settings (AFE settings alone) are manually configured and the existing
link-up sequence in the driver does not perform rx adaptation process as
mentioned in the Synopsys databook. There's a customer request for 10G
backplane mode without Auto-negotiation and for the DAC cables of more
significant length that follow the non-Autonegotiation mode. These modes
require PHY to perform RX Adaptation.

The proposed logic adds the necessary changes to Yellow Carp devices to
ensure seamless RX Adaptation for 10G-SFI (LONG DAC) and 10G-KR without
AN (CL72 not present). The RX adaptation core algorithm is executed by
firmware, however, to achieve that a new mailbox sub-command is required
to be sent by the driver.

Co-developed-by: Shyam Sundar S K <Shyam-sundar.S-k@amd.com>
Signed-off-by: Shyam Sundar S K <Shyam-sundar.S-k@amd.com>
Signed-off-by: Raju Rangoju <Raju.Rangoju@amd.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>

Add support to the driver to fully recognize and enable 2.5GbE speed in
10GBaseT mode.

Acked-by: Shyam Sundar S K <Shyam-sundar.S-k@amd.com>
Signed-off-by: Raju Rangoju <Raju.Rangoju@amd.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>

Pedro Tammela says:

====================
net/sched: transition act_pedit to rcu and percpu stats

The software pedit action didn't get the same love as some of the
other actions and it's still using spinlocks and shared stats.
Therefore, transition the action to rcu and percpu stats which
improves the action's performance.

We test this change with a very simple packet forwarding setup:

tc filter add dev ens2f0 ingress protocol ip matchall \
   action pedit ex munge eth src set b8:ce:f6:4b:68:35 pipe \
   action pedit ex munge eth dst set ac:1f:6b:e4:ff:93 pipe \
   action mirred egress redirect dev ens2f1
tc filter add dev ens2f1 ingress protocol ip matchall \
   action pedit ex munge eth src set b8:ce:f6:4b:68:34 pipe \
   action pedit ex munge eth dst set ac:1f:6b:e4:ff:92 pipe \
   action mirred egress redirect dev ens2f0

Using TRex with a http-like profile, in our setup with a 25G NIC
and a 26 cores Intel CPU, we observe the following in perf:
   before:
    11.59%  2.30%  [kernel]  [k] tcf_pedit_act
       2.55% tcf_pedit_act
             8.38% _raw_spin_lock
                       6.43% native_queued_spin_lock_slowpath
   after:
    1.46%  1.46%  [kernel]  [k] tcf_pedit_act

tdc results for pedit after the patch:
1..69
ok 1 319a - Add pedit action that mangles IP TTL
ok 2 7e67 - Replace pedit action with invalid goto chain
ok 3 377e - Add pedit action with RAW_OP offset u32
ok 4 a0ca - Add pedit action with RAW_OP offset u32 (INVALID)
ok 5 dd8a - Add pedit action with RAW_OP offset u16 u16
ok 6 53db - Add pedit action with RAW_OP offset u16 (INVALID)
ok 7 5c7e - Add pedit action with RAW_OP offset u8 add value
ok 8 2893 - Add pedit action with RAW_OP offset u8 quad
ok 9 3a07 - Add pedit action with RAW_OP offset u8-u16-u8
ok 10 ab0f - Add pedit action with RAW_OP offset u16-u8-u8
ok 11 9d12 - Add pedit action with RAW_OP offset u32 set u16 clear u8 invert
ok 12 ebfa - Add pedit action with RAW_OP offset overflow u32 (INVALID)
ok 13 f512 - Add pedit action with RAW_OP offset u16 at offmask shift set
ok 14 c2cb - Add pedit action with RAW_OP offset u32 retain value
ok 15 1762 - Add pedit action with RAW_OP offset u8 clear value
ok 16 bcee - Add pedit action with RAW_OP offset u8 retain value
ok 17 e89f - Add pedit action with RAW_OP offset u16 retain value
ok 18 c282 - Add pedit action with RAW_OP offset u32 clear value
ok 19 c422 - Add pedit action with RAW_OP offset u16 invert value
ok 20 d3d3 - Add pedit action with RAW_OP offset u32 invert value
ok 21 57e5 - Add pedit action with RAW_OP offset u8 preserve value
ok 22 99e0 - Add pedit action with RAW_OP offset u16 preserve value
ok 23 1892 - Add pedit action with RAW_OP offset u32 preserve value
ok 24 4b60 - Add pedit action with RAW_OP negative offset u16/u32 set value
ok 25 a5a7 - Add pedit action with LAYERED_OP eth set src
ok 26 86d4 - Add pedit action with LAYERED_OP eth set src & dst
ok 27 f8a9 - Add pedit action with LAYERED_OP eth set dst
ok 28 c715 - Add pedit action with LAYERED_OP eth set src (INVALID)
ok 29 8131 - Add pedit action with LAYERED_OP eth set dst (INVALID)
ok 30 ba22 - Add pedit action with LAYERED_OP eth type set/clear sequence
ok 31 dec4 - Add pedit action with LAYERED_OP eth set type (INVALID)
ok 32 ab06 - Add pedit action with LAYERED_OP eth add type
ok 33 918d - Add pedit action with LAYERED_OP eth invert src
ok 34 a8d4 - Add pedit action with LAYERED_OP eth invert dst
ok 35 ee13 - Add pedit action with LAYERED_OP eth invert type
ok 36 7588 - Add pedit action with LAYERED_OP ip set src
ok 37 0fa7 - Add pedit action with LAYERED_OP ip set dst
ok 38 5810 - Add pedit action with LAYERED_OP ip set src & dst
ok 39 1092 - Add pedit action with LAYERED_OP ip set ihl & dsfield
ok 40 02d8 - Add pedit action with LAYERED_OP ip set ttl & protocol
ok 41 3e2d - Add pedit action with LAYERED_OP ip set ttl (INVALID)
ok 42 31ae - Add pedit action with LAYERED_OP ip ttl clear/set
ok 43 486f - Add pedit action with LAYERED_OP ip set duplicate fields
ok 44 e790 - Add pedit action with LAYERED_OP ip set ce, df, mf, firstfrag, nofrag fields
ok 45 cc8a - Add pedit action with LAYERED_OP ip set tos
ok 46 7a17 - Add pedit action with LAYERED_OP ip set precedence
ok 47 c3b6 - Add pedit action with LAYERED_OP ip add tos
ok 48 43d3 - Add pedit action with LAYERED_OP ip add precedence
ok 49 438e - Add pedit action with LAYERED_OP ip clear tos
ok 50 6b1b - Add pedit action with LAYERED_OP ip clear precedence
ok 51 824a - Add pedit action with LAYERED_OP ip invert tos
ok 52 106f - Add pedit action with LAYERED_OP ip invert precedence
ok 53 6829 - Add pedit action with LAYERED_OP beyond ip set dport & sport
ok 54 afd8 - Add pedit action with LAYERED_OP beyond ip set icmp_type & icmp_code
ok 55 3143 - Add pedit action with LAYERED_OP beyond ip set dport (INVALID)
ok 56 815c - Add pedit action with LAYERED_OP ip6 set src
ok 57 4dae - Add pedit action with LAYERED_OP ip6 set dst
ok 58 fc1f - Add pedit action with LAYERED_OP ip6 set src & dst
ok 59 6d34 - Add pedit action with LAYERED_OP ip6 dst retain value (INVALID)
ok 60 94bb - Add pedit action with LAYERED_OP ip6 traffic_class
ok 61 6f5e - Add pedit action with LAYERED_OP ip6 flow_lbl
ok 62 6795 - Add pedit action with LAYERED_OP ip6 set payload_len, nexthdr, hoplimit
ok 63 1442 - Add pedit action with LAYERED_OP tcp set dport & sport
ok 64 b7ac - Add pedit action with LAYERED_OP tcp sport set (INVALID)
ok 65 cfcc - Add pedit action with LAYERED_OP tcp flags set
ok 66 3bc4 - Add pedit action with LAYERED_OP tcp set dport, sport & flags fields
ok 67 f1c8 - Add pedit action with LAYERED_OP udp set dport & sport
ok 68 d784 - Add pedit action with mixed RAW/LAYERED_OP #1
ok 69 70ca - Add pedit action with mixed RAW/LAYERED_OP #2
====================

Link: https://lore.kernel.org/r/20230131190512.3805897-1-pctammela@mojatatu.com


Signed-off-by: Paolo Abeni <pabeni@redhat.com>

Remove the check for a negative number of keys as
this cannot ever happen

Reviewed-by: Jamal Hadi Salim <jhs@mojatatu.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Pedro Tammela <pctammela@mojatatu.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>

The software pedit action didn't get the same love as some of the
other actions and it's still using spinlocks and shared stats in the
datapath.
Transition the action to rcu and percpu stats as this improves the
action's performance dramatically on multiple cpu deployments.

Reviewed-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: Pedro Tammela <pctammela@mojatatu.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>

David Howells says:

====================
Here's the fifth part of patches in the process of moving rxrpc from doing
a lot of its stuff in softirq context to doing it in an I/O thread in
process context and thereby making it easier to support a larger SACK
table.

The full description is in the description for the first part[1] which is
now upstream.  The second and third parts are also upstream[2].  A subset
of the original fourth part[3] got applied as a fix for a race[4].

The fifth part includes some cleanups:

 (1) Miscellaneous trace header cleanups: fix a trace string, display the
     security index in rx_packet rather than displaying the type twice,
     remove some whitespace to make checkpatch happier and remove some
     excess tabulation.

 (2) Convert ->recvmsg_lock to a spinlock as it's only ever locked
     exclusively.

 (3) Make ->ackr_window and ->ackr_nr_unacked non-atomic as they're only
     used in the I/O thread.

 (4) Don't use call->tx_lock to access ->tx_buffer as that is only accessed
     inside the I/O thread.  sendmsg() loads onto ->tx_sendmsg and the I/O
     thread decants from that to the buffer.

 (5) Remove local->defrag_sem as DATA packets are transmitted serially by
     the I/O thread.

 (6) Remove the service connection bundle is it was only used for its
     channel_lock - which has now gone.

And some more significant changes:

 (7) Add a debugging option to allow a delay to be injected into packet
     reception to help investigate the behaviour over longer links than
     just a few cm.

 (8) Generate occasional PING ACKs to probe for RTT information during a
     receive heavy call.

 (9) Simplify the SACK table maintenance and ACK generation.  Now that both
     parts are done in the same thread, there's no possibility of a race
     and no need to try and be cunning to avoid taking a BH spinlock whilst
     copying the SACK table (which in the future will be up to 2K) and no
     need to rotate the copy to fit the ACK packet table.

(10) Use SKB_CONSUMED when freeing received DATA packets (stop dropwatch
     complaining).

* tag 'rxrpc-next-20230131' of git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-fs:
  rxrpc: Kill service bundle
  rxrpc: Change rx_packet tracepoint to display securityIndex not type twice
  rxrpc: Show consumed and freed packets as non-dropped in dropwatch
  rxrpc: Remove local->defrag_sem
  rxrpc: Don't lock call->tx_lock to access call->tx_buffer
  rxrpc: Simplify ACK handling
  rxrpc: De-atomic call->ackr_window and call->ackr_nr_unacked
  rxrpc: Generate extra pings for RTT during heavy-receive call
  rxrpc: Allow a delay to be injected into packet reception
  rxrpc: Convert call->recvmsg_lock to a spinlock
  rxrpc: Shrink the tabulation in the rxrpc trace header a bit
  rxrpc: Remove whitespace before ')' in trace header
  rxrpc: Fix trace string
====================

Link: https://lore.kernel.org/all/20230131171227.3912130-1-dhowells@redhat.com/


Signed-off-by: Paolo Abeni <pabeni@redhat.com>

NPC exact match feature is supported only on one silicon
variant, removed debug messages which print that this
feature is not available on all other silicon variants.

Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: Ratheesh Kannoth <rkannoth@marvell.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Link: https://lore.kernel.org/r/20230201040301.1034843-1-rkannoth@marvell.com


Signed-off-by: Jakub Kicinski <kuba@kernel.org>

When the single-buffer xdp is loaded and after xdp_linearize_page()
is called, *num_buf becomes 0 and (*num_buf - 1) may overflow into
a large integer in virtnet_build_xdp_buff_mrg(), resulting in
unexpected packet dropping.

Fixes: ef75cb51 ("virtio-net: build xdp_buff with multi buffers")
Signed-off-by: Heng Qi <hengqi@linux.alibaba.com>
Reviewed-by: Xuan Zhuo <xuanzhuo@linux.alibaba.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Link: https://lore.kernel.org/r/20230131085004.98687-1-hengqi@linux.alibaba.com


Signed-off-by: Jakub Kicinski <kuba@kernel.org>

In netdev common pattern, extack pointer is forwarded to the drivers
to be filled with error message. However, the caller can easily
overwrite the filled message.

Instead of adding multiple "if (!extack->_msg)" checks before any
NL_SET_ERR_MSG() call, which appears after call to the driver, let's
add new macro to common code.

[1] https://lore.kernel.org/all/Y9Irgrgf3uxOjwUm@unreal


Reviewed-by: Simon Horman <simon.horman@corigine.com>
Reviewed-by: Nikolay Aleksandrov <razor@blackwall.org>
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Link: https://lore.kernel.org/r/6993fac557a40a1973dfa0095107c3d03d40bec1.1675171790.git.leon@kernel.org


Signed-off-by: Jakub Kicinski <kuba@kernel.org>

When set to zero, the neighbor sysctl proxy_delay value
does not cause an immediate reply for ARP/ND requests
as expected, it instead causes a random delay between
[0, U32_MAX). Looking at this comment from
__get_random_u32_below() explains the reason:

/*
 * This function is technically undefined for ceil == 0, and in fact
 * for the non-underscored constant version in the header, we build bug
 * on that. But for the non-constant case, it's convenient to have that
 * evaluate to being a straight call to get_random_u32(), so that
 * get_random_u32_inclusive() can work over its whole range without
 * undefined behavior.
 */

Added helper function that does not call get_random_u32_below()
if proxy_delay is zero and just uses the current value of
jiffies instead, causing pneigh_enqueue() to respond
immediately.

Also added definition of proxy_delay to ip-sysctl.txt since
it was missing.

Signed-off-by: Brian Haley <haleyb.dev@gmail.com>
Link: https://lore.kernel.org/r/20230130171428.367111-1-haleyb.dev@gmail.com


Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Xin Long says:

====================
net: support ipv4 big tcp

This is similar to the BIG TCP patchset added by Eric for IPv6:

  https://lwn.net/Articles/895398/

Different from IPv6, IPv4 tot_len is 16-bit long only, and IPv4 header
doesn't have exthdrs(options) for the BIG TCP packets' length. To make
it simple, as David and Paolo suggested, we set IPv4 tot_len to 0 to
indicate this might be a BIG TCP packet and use skb->len as the real
IPv4 total length.

This will work safely, as all BIG TCP packets are GSO/GRO packets and
processed on the same host as they were created; There is no padding
in GSO/GRO packets, and skb->len - network_offset is exactly the IPv4
packet total length; Also, before implementing the feature, all those
places that may get iph tot_len from BIG TCP packets are taken care
with some new APIs:

Patch 1 adds some APIs for iph tot_len setting and getting, which are
used in all these places where IPv4 BIG TCP packets may reach in Patch
2-7, Patch 8 adds a GSO_TCP tp_status for af_packet users, and Patch 9
add new netlink attributes to make IPv4 BIG TCP independent from IPv6
BIG TCP on configuration, and Patch 10 implements this feature.

Note that the similar change as in Patch 2-6 are also needed for IPv6
BIG TCP packets, and will be addressed in another patchset.

The similar performance test is done for IPv4 BIG TCP with 25Gbit NIC
and 1.5K MTU:

No BIG TCP:
for i in {1..10}; do netperf -t TCP_RR -H 192.168.100.1 -- -r80000,80000 -O MIN_LATENCY,P90_LATENCY,P99_LATENCY,THROUGHPUT|tail -1; done
168          322          337          3776.49
143          236          277          4654.67
128          258          288          4772.83
171          229          278          4645.77
175          228          243          4678.93
149          239          279          4599.86
164          234          268          4606.94
155          276          289          4235.82
180          255          268          4418.95
168          241          249          4417.82

Enable BIG TCP:
ip link set dev ens1f0np0 gro_ipv4_max_size 128000 gso_ipv4_max_size 128000
for i in {1..10}; do netperf -t TCP_RR -H 192.168.100.1 -- -r80000,80000 -O MIN_LATENCY,P90_LATENCY,P99_LATENCY,THROUGHPUT|tail -1; done
161          241          252          4821.73
174          205          217          5098.28
167          208          220          5001.43
164          228          249          4883.98
150          233          249          4914.90
180          233          244          4819.66
154          208          219          5004.92
157          209          247          4999.78
160          218          246          4842.31
174          206          217          5080.99

Thanks for the feedback from Eric and David Ahern.
====================

Link: https://lore.kernel.org/r/cover.1674921359.git.lucien.xin@gmail.com


Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Similar to Eric's IPv6 BIG TCP, this patch is to enable IPv4 BIG TCP.

Firstly, allow sk->sk_gso_max_size to be set to a value greater than
GSO_LEGACY_MAX_SIZE by not trimming gso_max_size in sk_trim_gso_size()
for IPv4 TCP sockets.

Then on TX path, set IP header tot_len to 0 when skb->len > IP_MAX_MTU
in __ip_local_out() to allow to send BIG TCP packets, and this implies
that skb->len is the length of a IPv4 packet; On RX path, use skb->len
as the length of the IPv4 packet when the IP header tot_len is 0 and
skb->len > IP_MAX_MTU in ip_rcv_core(). As the API iph_set_totlen() and
skb_ip_totlen() are used in __ip_local_out() and ip_rcv_core(), we only
need to update these APIs.

Also in GRO receive, add the check for ETH_P_IP/IPPROTO_TCP, and allows
the merged packet size >= GRO_LEGACY_MAX_SIZE in skb_gro_receive(). In
GRO complete, set IP header tot_len to 0 when the merged packet size
greater than IP_MAX_MTU in iph_set_totlen() so that it can be processed
on RX path.

Note that by checking skb_is_gso_tcp() in API iph_totlen(), it makes
this implementation safe to use iph->len == 0 indicates IPv4 BIG TCP
packets.

Signed-off-by: Xin Long <lucien.xin@gmail.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

This patch introduces gso_ipv4_max_size and gro_ipv4_max_size
per device and adds netlink attributes for them, so that IPV4
BIG TCP can be guarded by a separate tunable in the next patch.

To not break the old application using "gso/gro_max_size" for
IPv4 GSO packets, this patch updates "gso/gro_ipv4_max_size"
in netif_set_gso/gro_max_size() if the new size isn't greater
than GSO_LEGACY_MAX_SIZE, so that nothing will change even if
userspace doesn't realize the new netlink attributes.

Signed-off-by: Xin Long <lucien.xin@gmail.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Introduce TP_STATUS_GSO_TCP tp_status flag to tell the af_packet user
that this is a TCP GSO packet. When parsing IPv4 BIG TCP packets in
tcpdump/libpcap, it can use tp_len as the IPv4 packet len when this
flag is set, as iph tot_len is set to 0 for IPv4 BIG TCP packets.

Signed-off-by: Xin Long <lucien.xin@gmail.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

ipvlan devices calls netif_inherit_tso_max() to get the tso_max_size/segs
from the lower device, so when lower device supports BIG TCP, the ipvlan
devices support it too. We also should consider its iph tot_len accessing.

Signed-off-by: Xin Long <lucien.xin@gmail.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

It may process IPv4 TCP GSO packets in cipso_v4_skbuff_setattr(), so
the iph->tot_len update should use iph_set_totlen().

Note that for these non GSO packets, the new iph tot_len with extra
iph option len added may become greater than 65535, the old process
will cast it and set iph->tot_len to it, which is a bug. In theory,
iph options shouldn't be added for these big packets in here, a fix
may be needed here in the future. For now this patch is only to set
iph->tot_len to 0 when it happens.

Signed-off-by: Xin Long <lucien.xin@gmail.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

There are also quite some places in netfilter that may process IPv4 TCP
GSO packets, we need to replace them too.

In length_mt(), we have to use u_int32_t/int to accept skb_ip_totlen()
return value, otherwise it may overflow and mismatch. This change will
also help us add selftest for IPv4 BIG TCP in the following patch.

Note that we don't need to replace the one in tcpmss_tg4(), as it will
return if there is data after tcphdr in tcpmss_mangle_packet(). The
same in mangle_contents() in nf_nat_helper.c, it returns false when
skb->len + extra > 65535 in enlarge_skb().

Signed-off-by: Xin Long <lucien.xin@gmail.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

There are 1 action and 1 qdisc that may process IPv4 TCP GSO packets
and access iph->tot_len, replace them with skb_ip_totlen() and
iph_totlen() accordingly.

Note that we don't need to replace the one in tcf_csum_ipv4(), as it
will return for TCP GSO packets in tcf_csum_ipv4_tcp().

Signed-off-by: Xin Long <lucien.xin@gmail.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

IPv4 GSO packets may get processed in ovs_skb_network_trim(),
and we need to use skb_ip_totlen() to get iph totlen.

Signed-off-by: Xin Long <lucien.xin@gmail.com>
Reviewed-by: Aaron Conole <aconole@redhat.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

These 3 places in bridge netfilter are called on RX path after GRO
and IPv4 TCP GSO packets may come through, so replace iph tot_len
accessing with skb_ip_totlen() in there.

Signed-off-by: Xin Long <lucien.xin@gmail.com>
Reviewed-by: Nikolay Aleksandrov <razor@blackwall.org>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

This patch adds three APIs to replace the iph->tot_len setting
and getting in all places where IPv4 BIG TCP packets may reach,
they will be used in the following patches.

Note that iph_totlen() will be used when iph is not in linear
data of the skb.

Signed-off-by: Xin Long <lucien.xin@gmail.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Laurent Vivier says:

====================
virtio_net: vdpa: update MAC address when it is generated by virtio-net

When the MAC address is not provided by the vdpa device virtio_net
driver assigns a random one without notifying the device.
The consequence, in the case of mlx5_vdpa, is the internal routing
tables of the device are not updated and this can block the
communication between two namespaces.

To fix this problem, use virtnet_send_command(VIRTIO_NET_CTRL_MAC)
to set the address from virtnet_probe() when the MAC address is
not provided by the device.
====================

Link: https://lore.kernel.org/r/20230127204500.51930-1-lvivier@redhat.com


Signed-off-by: Jakub Kicinski <kuba@kernel.org>

In virtnet_probe(), if the device doesn't provide a MAC address the
driver assigns a random one.
As we modify the MAC address we need to notify the device to allow it
to update all the related information.

The problem can be seen with vDPA and mlx5_vdpa driver as it doesn't
assign a MAC address by default. The virtio_net device uses a random
MAC address (we can see it with "ip link"), but we can't ping a net
namespace from another one using the virtio-vdpa device because the
new MAC address has not been provided to the hardware:
RX packets are dropped since they don't go through the receive filters,
TX packets go through unaffected.

Signed-off-by: Laurent Vivier <lvivier@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

failover relies on the MAC address to pair the primary and the standby
devices:

  "[...] the hypervisor needs to enable VIRTIO_NET_F_STANDBY
   feature on the virtio-net interface and assign the same MAC address
   to both virtio-net and VF interfaces."

  Documentation/networking/net_failover.rst

This patch disables the STANDBY feature if the MAC address is not
provided by the hypervisor.

Signed-off-by: Laurent Vivier <lvivier@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

This patch corrects two oversights relating to releasing resources
and DCB initialisation.

1. If mapping of the dcbcfg_tbl area fails: an error should be
   propagated, allowing partial initialisation (probe) to be unwound.

2. Conversely, if where dcbcfg_tbl is successfully mapped: it should
   be unmapped in nfp_nic_dcb_clean() which is called via various error
   cleanup paths, and shutdown or removal of the PCIE device.

Fixes: 9b7fe804 ("nfp: add DCB IEEE support")
Signed-off-by: Huayu Chen <huayu.chen@corigine.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund@corigine.com>
Signed-off-by: Simon Horman <simon.horman@corigine.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Link: https://lore.kernel.org/r/20230131163033.981937-1-simon.horman@corigine.com


Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Swap is a function interface that provides exchange function. To avoid
code duplication, we can use swap function.

./net/ipv6/icmp.c:344:25-26: WARNING opportunity for swap().

Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Link: https://bugzilla.openanolis.cn/show_bug.cgi?id=3896


Signed-off-by: Jiapeng Chong <jiapeng.chong@linux.alibaba.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Link: https://lore.kernel.org/r/20230131063456.76302-1-jiapeng.chong@linux.alibaba.com


Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Jiri Pirko says:

====================
devlink: trivial names cleanup

This is a follow-up to Jakub's devlink code split and dump iteration
helper patchset. No functional changes, just couple of renames to makes
things consistent and perhaps easier to follow.
====================

Link: https://lore.kernel.org/r/20230131090613.2131740-1-jiri@resnulli.us


Signed-off-by: Jakub Kicinski <kuba@kernel.org>

In order to maintain naming consistency, rename and reorder all usages
of struct struct devlink_cmd in the following way:
1) Remove "gen" and replace it with "cmd" to match the struct name
2) Order devl_cmds[] and the header file to match the order
   of enum devlink_command
3) Move devl_cmd_rate_get among the peers
4) Remove "inst" for DEVLINK_CMD_GET
5) Add "_get" suffix to all to match DEVLINK_CMD_*_GET (only rate had it
   done correctly)

Signed-off-by: Jiri Pirko <jiri@nvidia.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

No need to have "gen" inside name of the structure for devlink commands.
Remove it.

Signed-off-by: Jiri Pirko <jiri@nvidia.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

To have the name of the function consistent with the struct cb name,
rename devlink_nl_instance_iter_dump() to
devlink_nl_instance_iter_dumpit().

Signed-off-by: Jiri Pirko <jiri@nvidia.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Alex Elder says:

====================
net: ipa: remaining IPA v5.0 support

This series includes almost all remaining IPA code changes required
to support IPA v5.0.  IPA register definitions and configuration
data for IPA v5.0 will be sent later (soon).  Note that the GSI
register definitions still require work.  GSI for IPA v5.0 supports
up to 256 (rather than 32) channels, and this changes the way GSI
register offsets are calculated.  A few GSI register fields also
change.

The first patch in this series increases the number of IPA endpoints
supported by the driver, from 32 to 36.  The next updates the width
of the destination field for the IP_PACKET_INIT immediate command so
it can represent up to 256 endpoints rather than just 32.  The next
adds a few definitions of some IPA registers and fields that are
first available in IPA v5.0.

The next two patches update the code that handles router and filter
table caches.  Previously these were referred to as "hashed" tables,
and the IPv4 and IPv6 tables are now combined into one "unified"
table.  The sixth and seventh patches add support for a new pulse
generator, which allows time periods to be specified with a wider
range of clock resolution.  And the last patch just defines two new
memory regions that were not previously used.
====================

Link: https://lore.kernel.org/r/20230130210158.4126129-1-elder@linaro.org


Signed-off-by: Jakub Kicinski <kuba@kernel.org>

IPA v5.0 uses two memory regions not previously used.  Define them
and treat them as valid only for IPA v5.0.

Signed-off-by: Alex Elder <elder@linaro.org>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

The AP has third pulse generator available starting with IPA v5.0.
Redefine ipa_qtime_val() to support that possibility.  Pass the IPA
pointer as an argument so the version can be determined.  And stop
using the sign of the returned tick count to indicate which of two
pulse generators to use.

Instead, have the caller provide the address of a variable that will
hold the selected pulse generator for the Qtime value.  And for
version 5.0, check whether the third pulse generator best represents
the time period.

Add code in ipa_qtime_config() to configure the fourth pulse
generator for IPA v5.0+; in that case configure both the third and
fourth pulse generators to use 10 msec granularity.

Consistently use "ticks" for local variables that represent a tick
count.

Signed-off-by: Alex Elder <elder@linaro.org>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Starting with IPA v5.0, the head-of-line blocking timer has more
than two pulse generators available to define timer granularity.
To prepare for that, change the way the field value is encoded
to use ipa_reg_encode() rather than ipa_reg_bit().

The aggregation granularity selection could (in principle) also use
an additional pulse generator starting with IPA v5.0.  Encode the
AGGR_GRAN_SEL field differently to allow that as well.

Signed-off-by: Alex Elder <elder@linaro.org>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

IPA v5.0+ separates the configuration of entries in the cached
(previously "hashed") routing and filtering tables into distinct
registers.  Previously a single "filter and router" register updated
entries in both tables at once; now the routing and filter table
caches have separate registers that define their content.

This patch updates the code that zeroes entries in the cached filter
and router tables to support IPA versions including v5.0+.

Signed-off-by: Alex Elder <elder@linaro.org>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Update the code that causes filter and router table caches to be
flushed so that it supports IPA versions 5.0+.  It adds a comment in
ipa_hardware_config_hashing() that explains that cacheing does not
need to be enabled, just as before, because it's enabled by default.
(For the record, the FILT_ROUT_CACHE_CFG register would have been
used if we wanted to explicitly enable these.)

Signed-off-by: Alex Elder <elder@linaro.org>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Define some new registers that appear starting with IPA v5.0, along
with enumerated types identifying their fields.  Code that uses
these will be added by upcoming patches.

Most of the new registers are related to filter and routing tables,
and in particular, their "hashed" variant.  These tables are better
described as "cached", where a hash value determines which entries
are cached.  From now on, naming related to this functionality will
use "cache" instead of "hash", and that is reflected in these new
register names.  Some registers for managing these caches and their
contents have changed as well.

A few other new field definitions for registers (unrelated to table
caches) are also defined.

Signed-off-by: Alex Elder <elder@linaro.org>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

The IP_PACKET_INIT immediate command defines the destination
endpoint to which a packet should be sent.  Prior to IPA v5.0, a
5 bit field in that command represents the endpoint, but starting
with IPA v5.0, the field is extended to 8 bits to support more than
32 endpoints.

Signed-off-by: Alex Elder <elder@linaro.org>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Increase the number of endpoints supported by the driver to 36,
which IPA v5.0 supports.  This makes it impossible to check at build
time whether the supported number is too big to fit within the
(5-bit) PACKET_INIT destination endpoint field.  Instead, convert
the build time check to compare against what fits in 8 bits.

Add a check in ipa_endpoint_config() to also ensure the hardware
reports an endpoint count that's in the expected range.  Just
open-code 32 as the limit (the PACKET_INIT field mask is not
available where we'd want to use it).

Signed-off-by: Alex Elder <elder@linaro.org>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>