Add the driver for the PEAK Systems USB CAN interface.

See: https://github.com/raspberrypi/linux/issues/4583



Signed-off-by: Phil Elwell <phil@raspberrypi.com>

Matches correct behaviour from DECODE and DEINTERLACE

Signed-off-by: Dom Cobley <popcornmix@gmail.com>

Adds another /dev/video node wrapping image_fx doing deinterlace.

Co-developed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Dom Cobley <popcornmix@gmail.com>

As we're wanting to wrap the image_fx component for deinterlacing,
add the deinterlace algorithm values to enum mmal_parameter_imagefx

Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>

If the client provides a bytesperline value in try_fmt/s_fmt then
validate it and correct if necessary.

Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>

The flags is a bitmask, so it's far easier to interpret as hex
data instead of decimal.

Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>

Should start_streaming fail, or buffers be queued during
stop_streaming, they should be returned to the core as QUEUED
and not (as currently) as ERROR.

Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>

Being YUV420 formats, the step size is always 2 to avoid part
chroma subsampling.

Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>

The video decoder can support decoding interlaced streams, so add
the required plumbing to signal this correctly.

The encoder and ISP do NOT support interlaced data, so trying to
configure an interlaced format on those nodes will be rejected.

Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>

Adds enum mmal_interlace_type and struct
mmal_parameter_video_interlace_type to allow for querying the
interlacing mode on decoders.

Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>

Add the buffer flags that the firmware uses to identify fields
on interlaced video

Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>

In order to effectively guarantee that a V4L2_EVENT_SOURCE_CHANGE
event occurs, adopt a default resolution of 32x32 so that it
is incredibly unlikely to be decoding a stream of that resolution
and therefore failing to note a "change" requiring the event.

Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>

The exit path of vc4_hdmi_encoder_pre_crtc_configure() is fairly hard to
maintain given its numerous error conditions.

Switch to a goto based approach to simplify it.

Signed-off-by: Maxime Ripard <maxime@cerno.tech>

Unlike pm_runtime_get_sync(), pm_runtime_resume_and_get() doesn't take a
reference on failure, so we don't need to call pm_runtime_put() on
failure.

Signed-off-by: Maxime Ripard <maxime@cerno.tech>

Our detect function calls pm_runtime_resume_and_get() and
pm_runtime_put() to make sure the device is properly powered before
trying to access the controller.

However, it also makes sure the HSM clock is properly enabled (and
disabled), which is redundant with what runtime_pm is doing already.
Let's just remove it.

Signed-off-by: Maxime Ripard <maxime@cerno.tech>

The older panel-raspberrypi-touchscreen driver had issues in
that it also controlled the power for the touchscreen without
having an appropriate hook for the touchscreen driver to control
that.

Mainline has now added a Toshiba TC358762 bridge driver, and
a regulator/backlight driver for the ATTiny microcontroller on
the board. That allows clean integration with the touchscreen
driver.

Switch the overlays over to using newer drivers.

Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>

Add the two newer drivers for the Pi 7" touchscreen to the defconfigs

Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>

We need independent control of the resets for the panel&bridge,
vs the touch controller.

Expose the reset lines that are on the Atmel's port C via the GPIO
API so that they can be controlled appropriately.

Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>

The Atmel was doing a load of automatic sequencing of
control lines, however it was combining the touch controller's
reset with the bridge/panel control.

Change to control the control signals directly rather than
through the automatic POWERON control.

Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>

The initial state of the Atmel is not defined, so ensure the
backlight PWM is set to 0 by default.

Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>

The driver was using the regmap lock to serialise the
individual accesses, but we really need to protect the
timings of enabling the regulators, including any communication
with the Atmel.

Use a mutex within the driver to control overall accesses to
the Atmel, instead of the regmap lock.

Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>

The Atmel is doing some things in the I2C ISR, during which
period it will not respond to further commands. This is
particularly true of the POWERON command.

Increase delays appropriately, and retry should I2C errors be
reported.

Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>

There's no reason why 2 Raspberry Pi DSI displays can't be
attached to a Pi Compute Module, so the backlight names need to
be unique.

Use the parent dev_name. It's not as readable, but is unique.

Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>

If no interrupt is defined then a timer and workqueue are used
to poll the controller.
On remove these were not being cleaned up correctly.

Fixes: ca61fdab

 "Input: edt-ft5x06: Poll the device if no interrupt is
configured."

Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>

The Raspberry Pi 7" 800x480 panel uses a Toshiba TC358762 DSI
to DPI bridge chip, so there is a requirement for the timings
to be specified for the end panel. Add such a definition.

Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>

rpi_touchscreen_i2c_read returns any errors from i2c_transfer,
or the 8 bit received value.
Check for error values before trying to process the data as
valid.

Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>

The panel has a prepare call which is before video starts, and an
enable call which is after.
The Toshiba bridge should be configured before video, so move
the relevant power and initialisation calls to prepare.

Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>

If a call to rpi_touchscreen_i2c_write from rpi_touchscreen_probe
fails before mipi_dsi_device_register_full is called, then
in trying to log the error message if uses ts->dsi->dev when
it is still NULL.

Use ts->i2c->dev instead, which is initialised earlier in probe.

Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>

The divider calculations tried to find the divider
just faster than the clock requested. However if
it required a divider of 7 then the for loop
aborted without handling the "error" case, and could
end up with a clock lower than requested.

Correct the loop so that we always have a clock greater
than requested.

Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>

On Pi0-3 the driver allocates a buffer and requests a DMA channel
because the ARM can't write to DSI1's registers directly.
However unbind and the error paths in bind don't release the buffer or
the DMA channel.

Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>

The HDMI block can repeat pixels for double clocked modes,
and the firmware is now configuring the block to do this as
the PV is doing it incorrectly when at 2pixels/clock.
If the kernel doesn't reset it then we end up with strange
modes.

Reset MISC_CONTROL.

Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>

The sysfs delay_ms value is calculated live, and it is possible for
the time left to appear to be negative briefly if the timer handling
hasn't completed. Ensure the displayed value never goes below zero,
for the sake of appearances.

Signed-off-by: Phil Elwell <phil@raspberrypi.com>

A module parameter "dpc_enable" is added to allow the control of the
sensor's on-board DPC (Defective Pixel Correction) function.

This is a global setting to be configured before using the sensor;
there is no intention that this would ever be changed on-the-fly.

Signed-off-by: David Plowman <david.plowman@raspberrypi.com>

Signed-off-by: Phil Elwell <phil@raspberrypi.com>

drm_connector_helper_hpd_irq_event() calls
drm_kms_helper_hotplug_event() with the mode-setting lock taken while
it's supposed to be called without that lock taken.

This results in a lockdep warning, and a deadlock if we were to wake up
a TV through CEC (and possibly other cases).

Signed-off-by: Maxime Ripard <maxime@cerno.tech>

Link: https://lore.kernel.org/r/20210906125449.756437409@linuxfoundation.org


Tested-by: Pavel Machek (CIP) <pavel@denx.de>
Tested-by: Fox Chen <foxhlchen@gmail.com>
Tested-by: Linux Kernel Functional Testing <lkft@linaro.org>
Tested-by: Hulk Robot <hulkrobot@huawei.com>
Tested-by: Sudip Mukherjee <sudip.mukherjee@codethink.co.uk>
Tested-by: Jon Hunter <jonathanh@nvidia.com>
Tested-by: Florian Fainelli <f.fainelli@gmail.com>
Tested-by: Shuah Khan <skhan@linuxfoundation.org>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Tested-by: Salvatore Bonaccorso <carnil@debian.org>

commit 514e9767 upstream.

My local syzbot instance hit memory leak in usb_set_configuration().
The problem was in unputted usb interface. In case of errors after
usb_get_intf() the reference should be putted to correclty free memory
allocated for this interface.

Fixes: ec16dae5

 ("V4L/DVB (7019): V4L: add support for Syntek DC1125 webcams")
Cc: stable@vger.kernel.org
Signed-off-by: Pavel Skripkin <paskripkin@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 15db1683

 upstream.

Server responds to LOOKUP and other ops (READDIRPLUS/CREATE/MKNOD/...)
with ourarg containing nodeid and generation.

If a fuse inode is found in inode cache with the same nodeid but different
generation, the existing fuse inode should be unhashed and marked "bad" and
a new inode with the new generation should be hashed instead.

This can happen, for example, with passhrough fuse filesystem that returns
the real filesystem ino/generation on lookup and where real inode numbers
can get recycled due to real files being unlinked not via the fuse
passthrough filesystem.

With current code, this situation will not be detected and an old fuse
dentry that used to point to an older generation real inode, can be used to
access a completely new inode, which should be accessed only via the new
dentry.

Note that because the FORGET message carries the nodeid w/o generation, the
server should wait to get FORGET counts for the nlookup counts of the old
and reused inodes combined, before it can free the resources associated to
that nodeid.

Stable backport notes:
* This is not a regression. The bug has been in fuse forever, but only
  a certain class of low level fuse filesystems can trigger this bug
* Because there is no way to check if this fix is applied in runtime,
  libfuse test_examples.py tests this fix with hardcoded check for
  kernel version >= 5.14
* After backport to stable kernel(s), the libfuse test can be updated
  to also check minimal stable kernel version(s)
* Depends on "fuse: fix bad inode" which is already applied to stable
  kernels v5.4.y and v5.10.y
* Required backporting helper inode_wrong_type()

Signed-off-by: Amir Goldstein <amir73il@gmail.com>
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/linux-fsdevel/CAOQ4uxi8DymG=JO_sAU+wS8akFdzh+PuXwW3Ebgahd2Nwnh7zA@mail.gmail.com/


Signed-off-by: Amir Goldstein <amir73il@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>