There are three pins can act as cif test clock for rk3399.
They're sourced from 24M and output 24M by default and some boards
may use them as camera 24M xvclk.

Signed-off-by: Shunqian Zheng <zhengsq@rock-chips.com>
Reviewed-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>

Correct the SPI Master node settings.

Signed-off-by: Thor Thayer <thor.thayer@linux.intel.com>
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>

The USB IP on the Stratix10 SoC needs the USB OCP(ecc) bit to get de-asserted
as well for the USB IP to work properly.

Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>

Enable USB on the Stratix10 devkit.

Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>

When replacing the cpm by cp0 and cps by cp1 [1] not only the label and
the alias were replaced but also the compatible string which was wrong.

Due to this the pinctrl driver was no more probed.

This patch fix it by reverting this change for the pinctrl compatible
string on Armada 8K.

[1]: "arm64: dts: marvell: replace cpm by cp0, cps by cp1"

Reviewed-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>

dtc complains about the lack of #coolin-cells properties for the
CPU nodes that are referred to as "cooling-device":

arch/arm64/boot/dts/mediatek/mt8173-evb.dtb: Warning (cooling_device_property): Missing property '#cooling-cells' in node /cpus/cpu@0 or bad phandle (referred from /thermal-zones/cpu_thermal/cooling-maps/map@0:cooling-device[0])
arch/arm64/boot/dts/mediatek/mt8173-evb.dtb: Warning (cooling_device_property): Missing property '#cooling-cells' in node /cpus/cpu@100 or bad phandle (referred from /thermal-zones/cpu_thermal/cooling-maps/map@1:cooling-device[0])

Apparently this property must be '<2>' to match the binding.

Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Tested-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Olof Johansson <olof@lixom.net>

The PMU node has no working interrupt, as shown by this dtc warning:

arch/arm64/boot/dts/altera/socfpga_stratix10_socdk.dtb: Warning (interrupts_property): Missing interrupt-parent for /pmu

This adds an interrupt-parent property so we can correct parse
that interrupt number.

Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Dinh Nguyen <dinguyen@kernel.org>
Signed-off-by: Olof Johansson <olof@lixom.net>

Use new binding about USB wakeup which now supports multi USB
wakeup glue layer between SSUSB and SPM.
Meanwhile remove dummy clocks of USB wakeup.

Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This is tested in the S400 dev board which use a RTL8211F PHY,
and the pins connect to the 'eth_rgmii_y_pins' group.

Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Yixun Lan <yixun.lan@amlogic.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>

Add DT info for the stmmac ethernet MAC which found in
the Amlogic's Meson-AXG SoC, also describe the ethernet
pinctrl & clock information here.

Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Yixun Lan <yixun.lan@amlogic.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>

Add DT info for the SPICC controller which found in
the Amlogic's Meson-AXG SoC.

Signed-off-by: Sunny Luo <sunny.luo@amlogic.com>
Signed-off-by: Yixun Lan <yixun.lan@amlogic.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>

Enable IR remote controller which found in Amlogic's Meson-AXG SoCs.

Signed-off-by: Yixun Lan <yixun.lan@amlogic.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>

Switch the uart_ao pclk to CLK81 since the clock driver is ready.

Signed-off-by: Yixun Lan <yixun.lan@amlogic.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>

This patch adds Ethernet aliases in the Marvell Armada 7040 DB, 8040 DB
and 8040 mcbin device trees so that the bootloader setup the MAC
addresses correctly.

Signed-off-by: Yan Markman <ymarkman@marvell.com>
[Antoine: commit message, small fixes]
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>

In preparation for the introduction of more than 2 CPs in upcoming
SoCs, it makes sense to move away from the "CP master" (cpm) and "CP
slave" (cps) naming, and use instead cp0/cp1.

This commit is the result of:

 sed 's%cpm%cp0g%' arch/arm64/boot/dts/marvell/*
 sed 's%cps%cp1g%' arch/arm64/boot/dts/marvell/*

So it is a purely mechaninal change.

Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Suggested-by: Hanna Hawa <hannah@marvell.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>

One concept of Marvell Armada 7K/8K SoCs is that they are made of HW
blocks composed of a variety of IPs (network, PCIe, SATA, XOR, SPI,
I2C, etc.), and those HW blocks can be duplicated several times within
a given SoC. The Armada 7K SoC has a single CP110 (so no duplication),
while the Armada 8K SoC has two CP110. In the future, SoCs with more
than 2 CP110s will be introduced.

In current kernel versions, the master CP110 is described in
armada-cp110-master.dtsi and the slave CP110 is described in
armada-cp110-slave.dtsi. Those files are basically exactly the same,
since they describe the same hardware. They only have a few
differences:

 - Base address of the registers is different for the "config-space"

 - Base address of the PCIe registers, MEM, CONF and IO areas were
   different

 - Labels (and phandles pointing to them) of the nodes were different
   ("cpm" prefix in the master CP, "cps" prefix in the slave CP)

This duplication issue has been discussed at the DT workshop [1] in
Prague last October, and we presented on this topic [2]. The solution
of using the C pre-processor to avoid this duplication has been
validated by the people present in this DT workshop, and this patch
simply implements what has been presented.

We handle differences between the master CP and slave CP description
using the C pre-processor, by defining a set of macros with different
values armada-cp110.dtsi is included to instantiate one of the master
or slave CP110.

There are a few aspects that deserve additional explanations:

 - PCIe needs to be handled separately because it is not part of the
   config-space {...} node, since it has registers outside of the
   range covered by config-space {...}.

 - We need to defined CP110_BASE, CP110_PCIEx_BASE without 0x, because
   they are used for the unit address part of some DT nodes. But since
   they are also used for the "reg" property of the same nodes, we
   have an ADDRESSIFY() macro that prepends 0x to those values.

We compared the resulting .dtb for armada-8040-db.dtb before and after
this patch is applied, and the result is exactly the same, except for
a few differences:

 - the SDHCI controller that was only described in the master CP110 is
   now also described in the slave CP110. Even though the SDHCI
   controller from the slave CP110 is indeed not usable (as it isn't
   wired to the outside world) it is technically part of the silicon,
   and therefore it is reasonable to also describe it to be part of
   the slave CP110. In addition, if we wanted to get this correct for
   the SDHCI controller, we should also do it for the NAND controller,
   for which the situation is even more complicated: in a single CP110
   configuration (Armada 7K), the usable NAND controller is in the
   master CP110, while in a dual CP110 configuration (Armada 8K), the
   usable NAND controller is in the slave CP110. Since that would add
   a lot of additional complexity for no good reason, and since the IP
   blocks are in fact really present in both CPs, we simply describe
   them in both CPs at the DT level.

 - the cp110-master and cp110-slave nodes are now named cpm and
   cps. We could have kept cp110-master and cp110-slave, but that
   would have required adding another CP110_xyz define, which didn't
   seem very useful.

Note that this commit also gets rid of the armada-cp110-master.dtsi
and armada-cp110-slave.dtsi files, as future SoCs will have more than
2 CPs. Instead, we instantiate the CPs directly from the SoC-specific
.dtsi files, i.e armada-70x0.dtsi and armada-80x0.dtsi.

[1] https://elinux.org/Device_tree_kernel_summit_2017_etherpad
[2] https://elinux.org/images/1/14/DTWorkshop2017-duplicate-data.pdf



[gregory.clement@free-electrons.com: add back the "ARM64: dts: marvell:
Fix clock resources for various node" commit]
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>

We are currently using the cell-index DT property to assign SPI bus
numbers. This property is specific to the spi-orion driver, and
requires each SPI controller to have a unique ID defined in the Device
Tree.

As we are about to merge armada-cp110-master.dtsi and
armada-cp110-slave.dtsi into a single file, those cell-index
properties that differ between the master CP110 and the slave CP110
are a difference that would have to be handled.

In order to avoid this, we switch to using the "aliases" DT node to
assign a unique number to each SPI controller. This is more generic,
and directly handled by the SPI core.

Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>

Back when the ICU Device Tree binding was introduced, we could not use
mvebu-icu.h from the Device Tree files, because the DT files and
mvebu-icu.h were following different merge routes towards Linus
tree. Now that both have been merged, we can switch the Marvell Armada
CP110 Device Tree files to use the mvebu-icu.h header instead of
duplicating the ICU_GRP_NSR definition.

Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>

The Armada CP110 slave NAND controller Device Tree description lists
the compatible string in the wrong order: marvell,armada-8k-nand
should come first. This commit alignes the slave CP110 description
with the master CP110 description from that respect.

Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>

Fix the same typo duplicated in both master and slave version of
armada-cp110-*.dtsi file: s/limiation/limitation/.

[gregory.clement@free-electrons.com: add the commit log]
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>

This fixes the following DTC warning:

  <stdout>: Warning (simple_bus_reg): Node /ap806/config-space@f0000000/thermal@6f808C simple-bus unit address format error, expected "6f808c"

Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>

This fixes the following DTC warning:

  Warning (simple_bus_reg): Node /ap806/config-space@f0000000/watchdog@600000 simple-bus unit address format error, expected "610000"

Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>

This patch adds a crypto node describing the EIP97 engine found in
Armada 37xx SoCs. The cryptographic engine is enabled by default.

Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>

On the CP modules we found on Armada 7K/8K, many IP block actually also
need a "functional" clock (from the bus). This patch add them which allows
to fix some issues hanging the kernel:

If Ethernet and sdhci driver are built as modules and sdhci was loaded
first then the kernel hang.

Fixes: bb16ea17

 ("mmc: sdhci-xenon: Fix clock resource by adding an
optional bus clock")
Cc: stable@vger.kernel.org
Reported-by: Riku Voipio <riku.voipio@linaro.org>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>

The added header inclusion broke the 'allmodconfig' build in
arm-soc, presumably since the file is added in a different tree:

In file included from arch/arm64/boot/dts/sprd/sp9860g-1h10.dts:11:0:
arch/arm64/boot/dts/sprd/sc9860.dtsi:10:10: fatal error: dt-bindings/clock/sprd,sc9860-clk.h: No such file or directory

It turns out we don't actually need to include it at all, so
I'm removing the line again to fix the build.

Fixes: 22f37a24

 ("arm64: dts: add clocks for SC9860")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>

Some clocks on SC9860 are in the same address area with syscon devices,
those are what have a property of 'sprd,syscon' which would refer to
syscon devices, others would have a reg property indicated their address
ranges.

Signed-off-by: Chunyan Zhang <chunyan.zhang@spreadtrum.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>

Some clocks on SC9860 are in the same address area with syscon
devices, the proper syscon node will be quoted under the
definitions of those clocks in DT.

Signed-off-by: Chunyan Zhang <chunyan.zhang@spreadtrum.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>

This is probably a copy-paste mistake.  The gpio-ranges of PXs3 is
different from that of LD20.

Fixes: 277b51e7

 ("arm64: dts: uniphier: add GPIO controller nodes")
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>

Replace GPL v2.0 license statements with SPDX license identifiers.

Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>

Fix typo in unit address of MSCL clock controller (the reg entry is
correct) of Exynso5433.

Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>

Convert all hex addresses in node unit addresses to lower case to
fix warnings like:
    arch/arm64/boot/dts/exynos/exynos5433-tm2e.dtb: Warning (simple_bus_reg):
      Node /soc/video-scaler@13C00000 simple-bus unit address format error, expected "13c00000"

Conversion was done using sed:
    $ sed -e 's/@\([a-zA-Z0-9_-]*\) {/@\L\1 {/' -i arch/arm64/boot/dts/exynos/*.dts*

Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>

This node was the only one that didn't have the same set of pins in
active and suspend mode.

Signed-off-by: Damien Riegel <damien.riegel@savoirfairelinux.com>
Signed-off-by: Andy Gross <andy.gross@linaro.org>

Nodes relative to the first sdhc node were interlaced with node of the
second sdhc. Move sdhc2_cd_pin with its siblings to prevent that. Also
rename the grouping node from sdhc2_cd_pin to pmx_sdc2_cd_pin, as
"pmx_sdc" is the prefix used by other nodes.

Signed-off-by: Damien Riegel <damien.riegel@savoirfairelinux.com>
Acked-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>

The QUP core can be used either for I2C or SPI, so the same IP is mapped
by a driver or the other. SPI bindings use a leading 0 for the start
address and a size of 0x600, I2C bindings don't have the leading 0 and
have a size 0x1000.

To make them more similar, add the leading 0 to I2C bindings and changes
the size to 0x500 for all of them, as this is the actual size of these
blocks. Also align the second entry of the clocks array.

Signed-off-by: Damien Riegel <damien.riegel@savoirfairelinux.com>
Acked-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>

These nodes reserve and configure some pins as GPIOs. They are not
generic pinctrls, they actually belong to board files but they are not
used by any other node, so just drop them altogether.

Signed-off-by: Damien Riegel <damien.riegel@savoirfairelinux.com>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>

Drop assignments to bias-disable as the documentation [1] states that
this property doesn't take a value. Other occurrences of this property
respect that.

[1] Documentation/devicetree/bindings/pinctrl/qcom,msm8916-pinctrl.txt

Signed-off-by: Damien Riegel <damien.riegel@savoirfairelinux.com>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>

Indentation did not respect kernel standards, so fix that for the usual
indent with tabs, align with spaces. While at it, remove some empty
lines before and after the closing parenthesis of this block.

Signed-off-by: Damien Riegel <damien.riegel@savoirfairelinux.com>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>

SMSM is not symmetrical, the incoming bits from WCNSS are available at
index 6, but the outgoing host id for WCNSS is 3. Further more, upstream
references the base of APCS (in contrast to downstream), so the register
offset of 8 must be included.

Fixes: 1fb47e0a

 ("arm64: dts: qcom: msm8916: Add smsm and smp2p nodes")
Cc: stable@vger.kernel.org
Reported-by: Ramon Fried <rfried@codeaurora.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>

Add a missing #phy-cells to the dsi-phy, to silence dtc warning.

Cc: Archit Taneja <architt@codeaurora.org>
Fixes: 305410ff

 ("arm64: dts: msm8916: Add display support")
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>

The serial pins of PXs3 SoC are not multiplexed with any other
functions.  Enable serial2 and serial3 on the PXs3 reference board
because I see the connectors on the board.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>