SCMIv2.0 adds a new Reset Management Protocol to manage various reset
states a given device or domain can enter. Extend the existing SCMI
bindings to add reset protocol support by re-using the reset bindings
for both reset providers and consumers.

Cc: Philipp Zabel <p.zabel@pengutronix.de>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: devicetree@vger.kernel.org
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>

SCMI v2.0 adds support for "FastChannel" which do not use a message
header as they are specialized for a single message.

Only PERFORMANCE_LIMITS_{SET,GET} and PERFORMANCE_LEVEL_{SET,GET}
commands are supported over fastchannels. As they are optional, they
need to be discovered by PERFORMANCE_DESCRIBE_FASTCHANNEL command.
Further {LIMIT,LEVEL}_SET commands can have optional doorbell support.

Add support for making use of these fastchannels.

Cc: Ionela Voinescu <Ionela.Voinescu@arm.com>
Cc: Chris Redpath <Chris.Redpath@arm.com>
Cc: Quentin Perret <Quentin.Perret@arm.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>

SCMI v2.0 adds support for "FastChannel", a lightweight unidirectional
channel that is dedicated to a single SCMI message type for controlling
a specific platform resource. They do not use a message header as they
are specialized for a single message.

Only PERFORMANCE_LIMITS_{SET,GET} and PERFORMANCE_LEVEL_{SET,GET}
commands are supported over fastchannels. As they are optional, they
need to be discovered by PERFORMANCE_DESCRIBE_FASTCHANNEL command.
Further {LIMIT,LEVEL}_SET commands can have optional doorbell support.

Add support for discovery of these fastchannels.

Cc: Ionela Voinescu <Ionela.Voinescu@arm.com>
Cc: Chris Redpath <Chris.Redpath@arm.com>
Cc: Quentin Perret <Quentin.Perret@arm.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>

Instead of type-casting the {tx,rx}.buf all over the place while
accessing them to read/write __le{32,64} from/to the firmware, let's
use the existing {get,put}_unaligned_le{32,64} accessors to hide all
the type cast ugliness.

Suggested-by: Philipp Zabel <p.zabel@pengutronix.de>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>

CLOCK_PROTOCOL_ATTRIBUTES provides attributes to indicate the maximum
number of pending asynchronous clock rate changes supported by the
platform. If it's non-zero, then we should be able to use asynchronous
clock rate set for any clocks until the maximum limit is reached.

Tracking the current count of pending asynchronous clock set rate
requests, we can decide if the incoming/new request for clock set rate
can be handled asynchronously or not until the maximum limit is
reached.

Cc: linux-clk@vger.kernel.org
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>

CLOCK_PROTOCOL_ATTRIBUTES provides attributes to indicate the maximum
number of pending asynchronous clock rate changes supported by the
platform. If it's non-zero, then we should be able to use asynchronous
clock rate set for any clocks until the maximum limit is reached.

In order to add that support, let's drop the config flag passed to
clk_ops->rate_set and handle the asynchronous requests dynamically.

Cc: Stephen Boyd <sboyd@kernel.org>
Cc: linux-clk@vger.kernel.org
Acked-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>

SENSOR_DESCRIPTION_GET provides attributes to indicate if the sensor
supports asynchronous read. We can read that flag and use asynchronous
reads for any sensors with that attribute set.

Let's use the new scmi_do_xfer_with_response to support asynchronous
sensor reads.

Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>

SENSOR_DESCRIPTION_GET provides attributes to indicate if the sensor
supports asynchronous read. Ideally we should be able to read that flag
and use asynchronous reads for any sensors with that attribute set.

In order to add that support, let's drop the async flag passed to
sensor_ops->reading_get and dynamically switch between sync and async
flags based on the attributes as provided by the firmware.

Cc: linux-hwmon@vger.kernel.org
Acked-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>

Messages that are sent to platform, also known as commands and can be:

1. Synchronous commands that block the channel until the requested work
has been completed. The platform responds to these commands over the
same channel and hence can't be used to send another command until the
previous command has completed.

2. Asynchronous commands on the other hand, the platform schedules the
requested work to complete later in time and returns almost immediately
freeing the channel for new commands. The response indicates the success
or failure in the ability to schedule the requested work. When the work
has completed, the platform sends an additional delayed response message.

Using the same transmit buffer used for sending the asynchronous command
even for the delayed response corresponding to it simplifies handling of
the delayed response. It's the caller of asynchronous command that is
responsible for allocating the completion flag that scmi driver can
complete to indicate the arrival of delayed response.

Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>

In order to identify the message type when a response arrives, we need
a mechanism to unpack the message header similar to packing. Let's
add one.

Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>

Currently we pre-allocate transmit buffers only and use the first free
slot in that pre-allocated buffer for transmitting any new message that
are generally originated from OS to the platform firmware.

Notifications or the delayed responses on the other hand are originated
from the platform firmware and consumes by the OS. It's better to have
separate and dedicated pre-allocated buffers to handle the notifications.
We can still use the transmit buffers for the delayed responses.

In addition, let's prepare existing scmi_xfer_{get,put} for acquiring
and releasing a slot to identify the right(tx/rx) buffers.

Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>

With scmi_mbox_chan_setup enabled to identify and setup both Tx and Rx,
let's consolidate setting up of both the channels under the function
scmi_mbox_txrx_setup.

Since some platforms may opt not to support notifications or delayed
response, they may not need support for Rx. Hence Rx is optional and
failure of setting one up is not considered fatal.

Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>

The transmit(Tx) channels are specified as the first entry and the
receive(Rx) channels are the second entry as per the device tree
bindings. Since we currently just support Tx, index 0 is hardcoded at
all required callsites.

In order to prepare for adding Rx support, let's remove those hardcoded
index and add boolean parameter to identify Tx/Rx channels when setting
them up.

Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>

Re-shuffling few functions to keep definitions and their usages close.
This is also needed to avoid too many unnecessary forward declarations
while adding new features(delayed response and notifications).

Keeping this separate to avoid mixing up of these trivial change that
doesn't affect functionality into the ones that does.

Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>

Sometimes platfom may take too long to respond to the command and OS
might timeout before platform transfer the ownership of the shared
memory region to the OS with the response.

Since the mailbox channel associated with the channel is freed and new
commands are dispatch on the same channel, OS needs to wait until it
gets back the ownership. If not, either OS may end up overwriting the
platform response for the last command(which is fine as OS timed out
that command) or platform might overwrite the payload for the next
command with the response for the old.

The latter is problematic as platform may end up interpretting the
response as the payload. In order to avoid such race, let's wait until
the OS gets back the ownership before we prepare the shared memory with
the payload for the next command.

Reported-by: Jim Quinlan <james.quinlan@broadcom.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>

In preparation to adding support for other two types of messages that
SCMI specification mentions, let's replace the term 'command' with the
correct term 'message'.

As per the specification the messages are of 3 types:
commands(synchronous or asynchronous), delayed responses and notifications.

Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>

While adding new comments found couple of typos that are better fixed.

s/informfation/information/
s/statues/status/

Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>

scmi_xfer_get_init ensures both transmit and receive buffer lengths are
within the maximum limits. If receive buffer length is not supplied by
the caller, it's set to the maximum limit value. Receive buffer length
is never modified after that. So there's no need for the extra check
when receive transmit completion for a command essage.

Further, if the response header length is greater than the prescribed
receive buffer length, the response buffer is truncated to the latter.

Reported-by: Jim Quinlan <james.quinlan@broadcom.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>

Looks like more code developed during the draft versions of the
specification slipped through and they don't match the final
released version. This seem to have happened only with sensor
protocol.

Renaming few command and function names here to match exactly with
the released version of SCMI specification for ease of maintenance.

Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>

Fix to correct the SPDX License Identifier style in header file related
to firmware frivers for ARM SCMI message protocol.

For C header files Documentation/process/license-rules.rst mandates
C-like comments(opposed to C source files where C++ style should be
used).

While at it, change GPL-2.0 to GPL-2.0-only similar to the ones in
psci.h and scpi_protocol.h

Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>

Pull Devicetree fixes from Rob Herring:
 "Fix several warnings/errors in validation of binding schemas"

* tag 'devicetree-fixes-for-5.3' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux:
  dt-bindings: pinctrl: stm32: Fix missing 'clocks' property in examples
  dt-bindings: iio: ad7124: Fix dtc warnings in example
  dt-bindings: iio: avia-hx711: Fix avdd-supply typo in example
  dt-bindings: pinctrl: aspeed: Fix AST2500 example errors
  dt-bindings: pinctrl: aspeed: Fix 'compatible' schema errors
  dt-bindings: riscv: Limit cpus schema to only check RiscV 'cpu' nodes
  dt-bindings: Ensure child nodes are of type 'object'

Pull vfs documentation typo fix from Al Viro.

* 'work.misc' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
  typo fix: it's d_make_root, not d_make_inode...

Pull cifs fixes from Steve French:
 "Two fixes for stable, one that had dependency on earlier patch in this
  merge window and can now go in, and a perf improvement in SMB3 open"

* tag '5.3-smb3-fixes' of git://git.samba.org/sfrench/cifs-2.6:
  cifs: update internal module number
  cifs: flush before set-info if we have writeable handles
  smb3: optimize open to not send query file internal info
  cifs: copy_file_range needs to strip setuid bits and update timestamps
  CIFS: fix deadlock in cached root handling

The commit b3aa14f0 ("iommu: remove the mapping_error dma_map_ops
method") incorrectly changed the checking from dma_ops_alloc_iova() in
map_sg() causes a crash under memory pressure as dma_ops_alloc_iova()
never return DMA_MAPPING_ERROR on failure but 0, so the error handling
is all wrong.

   kernel BUG at drivers/iommu/iova.c:801!
    Workqueue: kblockd blk_mq_run_work_fn
    RIP: 0010:iova_magazine_free_pfns+0x7d/0xc0
    Call Trace:
     free_cpu_cached_iovas+0xbd/0x150
     alloc_iova_fast+0x8c/0xba
     dma_ops_alloc_iova.isra.6+0x65/0xa0
     map_sg+0x8c/0x2a0
     scsi_dma_map+0xc6/0x160
     pqi_aio_submit_io+0x1f6/0x440 [smartpqi]
     pqi_scsi_queue_command+0x90c/0xdd0 [smartpqi]
     scsi_queue_rq+0x79c/0x1200
     blk_mq_dispatch_rq_list+0x4dc/0xb70
     blk_mq_sched_dispatch_requests+0x249/0x310
     __blk_mq_run_hw_queue+0x128/0x200
     blk_mq_run_work_fn+0x27/0x30
     process_one_work+0x522/0xa10
     worker_thread+0x63/0x5b0
     kthread+0x1d2/0x1f0
     ret_from_fork+0x22/0x40

Fixes: b3aa14f0

 ("iommu: remove the mapping_error dma_map_ops method")
Signed-off-by: Qian Cai <cai@lca.pw>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

The hexagon implementation pte_alloc_one(), pte_alloc_one_kernel(),
pte_free_kernel() and pte_free() is identical to the generic except of
lack of __GFP_ACCOUNT for the user PTEs allocation.

Switch hexagon to use generic version of these functions.

Signed-off-by: Mike Rapoport <rppt@linux.ibm.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull NTB updates from Jon Mason:
 "New feature to add support for NTB virtual MSI interrupts, the ability
  to test and use this feature in the NTB transport layer.

  Also, bug fixes for the AMD and Switchtec drivers, as well as some
  general patches"

* tag 'ntb-5.3' of git://github.com/jonmason/ntb: (22 commits)
  NTB: Describe the ntb_msi_test client in the documentation.
  NTB: Add MSI interrupt support to ntb_transport
  NTB: Add ntb_msi_test support to ntb_test
  NTB: Introduce NTB MSI Test Client
  NTB: Introduce MSI library
  NTB: Rename ntb.c to support multiple source files in the module
  NTB: Introduce functions to calculate multi-port resource index
  NTB: Introduce helper functions to calculate logical port number
  PCI/switchtec: Add module parameter to request more interrupts
  PCI/MSI: Support allocating virtual MSI interrupts
  ntb_hw_switchtec: Fix setup MW with failure bug
  ntb_hw_switchtec: Skip unnecessary re-setup of shared memory window for crosslink case
  ntb_hw_switchtec: Remove redundant steps of switchtec_ntb_reinit_peer() function
  NTB: correct ntb_dev_ops and ntb_dev comment typos
  NTB: amd: Silence shift wrapping warning in amd_ntb_db_vector_mask()
  ntb_hw_switchtec: potential shift wrapping bug in switchtec_ntb_init_sndev()
  NTB: ntb_transport: Ensure qp->tx_mw_dma_addr is initaliazed
  NTB: ntb_hw_amd: set peer limit register
  NTB: ntb_perf: Clear stale values in doorbell and command SPAD register
  NTB: ntb_perf: Disable NTB link after clearing peer XLAT registers
  ...

Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>

Now that examples are validated against the DT schema, an error with
required 'clocks' property missing is exposed:

Documentation/devicetree/bindings/pinctrl/st,stm32-pinctrl.example.dt.yaml: \
pinctrl@40020000: gpio@0: 'clocks' is a required property
Documentation/devicetree/bindings/pinctrl/st,stm32-pinctrl.example.dt.yaml: \
pinctrl@50020000: gpio@1000: 'clocks' is a required property
Documentation/devicetree/bindings/pinctrl/st,stm32-pinctrl.example.dt.yaml: \
pinctrl@50020000: gpio@2000: 'clocks' is a required property

Add the missing 'clocks' properties to the examples to fix the errors.

Fixes: 2c9239c1

 ("dt-bindings: pinctrl: Convert stm32 pinctrl bindings to json-schema")
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: linux-gpio@vger.kernel.org
Cc: linux-stm32@st-md-mailman.stormreply.com
Acked-by: Alexandre TORGUE <alexandre.torgue@st.com>
Signed-off-by: Rob Herring <robh@kernel.org>

With the conversion to DT schema, the examples are now compiled with
dtc. The ad7124 binding example has the following warning:

Documentation/devicetree/bindings/iio/adc/adi,ad7124.example.dts:19.11-21: \
Warning (reg_format): /example-0/adc@0:reg: property has invalid length (4 bytes) (#address-cells == 1, #size-cells == 1)

There's a default #size-cells and #address-cells values of 1 for
examples. For examples needing different values such as this one on a
SPI bus, they need to provide a SPI bus parent node.

Fixes: 26ae15e6

 ("Convert AD7124 bindings documentation to YAML format.")

Cc: Jonathan Cameron <jic23@kernel.org>
Cc: linux-iio@vger.kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>

Now that examples are validated against the DT schema, a typo in
avia-hx711 example generates a warning:

Documentation/devicetree/bindings/iio/adc/avia-hx711.example.dt.yaml: weight: 'avdd-supply' is a required property

Fix the typo.

Fixes: 5150ec3f

 ("avia-hx711.yaml: transform DT binding to YAML")
Cc: Andreas Klinger <ak@it-klinger.de>
Cc: Jonathan Cameron <jic23@kernel.org>
Cc: linux-iio@vger.kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>

The schema examples are now validated against the schema itself. The
AST2500 pinctrl schema has a couple of errors:

Documentation/devicetree/bindings/pinctrl/aspeed,ast2500-pinctrl.example.dt.yaml: \
example-0: $nodename:0: 'example-0' does not match '^(bus|soc|axi|ahb|apb)(@[0-9a-f]+)?$'
Documentation/devicetree/bindings/pinctrl/aspeed,ast2500-pinctrl.example.dt.yaml: \
pinctrl: aspeed,external-nodes: [[1, 2]] is too short

Fixes: 0a617de1

 ("dt-bindings: pinctrl: aspeed: Convert AST2500 bindings to json-schema")
Cc: Andrew Jeffery <andrew@aj.id.au>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Joel Stanley <joel@jms.id.au>
Cc: linux-aspeed@lists.ozlabs.org
Cc: linux-gpio@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org
Acked-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Rob Herring <robh@kernel.org>

The Aspeed pinctl schema have errors in the 'compatible' schema:

Documentation/devicetree/bindings/pinctrl/aspeed,ast2400-pinctrl.yaml: \
properties:compatible:enum: ['aspeed', 'ast2400-pinctrl', 'aspeed', 'g4-pinctrl'] has non-unique elements
Documentation/devicetree/bindings/pinctrl/aspeed,ast2500-pinctrl.yaml: \
properties:compatible:enum: ['aspeed', 'ast2500-pinctrl', 'aspeed', 'g5-pinctrl'] has non-unique elements

Flow style sequences have to be quoted if the vales contain ','. Fix
this by using the more common one line per entry formatting.

Fixes: 0a617de1 ("dt-bindings: pinctrl: aspeed: Convert AST2500 bindings to json-schema")
Fixes: 07457937

 ("dt-bindings: pinctrl: aspeed: Convert AST2400 bindings to json-schema")
Cc: Andrew Jeffery <andrew@aj.id.au>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Joel Stanley <joel@jms.id.au>
Cc: linux-aspeed@lists.ozlabs.org
Cc: linux-gpio@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org
Acked-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Rob Herring <robh@kernel.org>

Matching on the 'cpus' node was a bad choice because the schema is
incorrectly applied to non-RiscV cpus nodes. As we now have a common cpus
schema which checks the general structure, it is also redundant to do so
in the Risc-V CPU schema.

The downside is one could conceivably mix different architecture's cpu
nodes or have typos in the compatible string. The latter problem pretty
much exists for every schema.

Acked-by: Paul Walmsley <paul.walmsley@sifive.com>
Signed-off-by: Rob Herring <robh@kernel.org>

Properties which are child node definitions need to have an explict
type. Otherwise, a matching (DT) property can silently match when an
error is desired. Fix this up tree-wide. Once this is fixed, the
meta-schema will enforce this on any child node definitions.

Cc: Chen-Yu Tsai <wens@csie.org>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Brian Norris <computersforpeace@gmail.com>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Vignesh Raghavendra <vigneshr@ti.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: linux-mtd@lists.infradead.org
Cc: linux-gpio@vger.kernel.org
Cc: linux-stm32@st-md-mailman.stormreply.com
Cc: linux-spi@vger.kernel.org
Acked-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Mark Brown <broonie@kernel.org>
Acked-by: Alexandre TORGUE <alexandre.torgue@st.com>
Signed-off-by: Rob Herring <robh@kernel.org>

Pull more input updates from Dmitry Torokhov:

 - Apple SPI keyboard and trackpad driver for newer Macs

 - ALPS driver will ignore trackpoint-only devices to give the
   trackpoint driver a chance to handle them properly

 - another Lenovo is switched over to SMbus from PS/2

 - assorted driver fixups.

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
  Input: alps - fix a mismatch between a condition check and its comment
  Input: psmouse - fix build error of multiple definition
  Input: applespi - remove set but not used variables 'sts'
  Input: add Apple SPI keyboard and trackpad driver
  Input: alps - don't handle ALPS cs19 trackpoint-only device
  Input: hyperv-keyboard - remove dependencies on PAGE_SIZE for ring buffer
  Input: adp5589 - initialize GPIO controller parent device
  Input: iforce - remove empty multiline comments
  Input: synaptics - fix misuse of strlcpy
  Input: auo-pixcir-ts - switch to using  devm_add_action_or_reset()
  Input: gtco - bounds check collection indent level
  Input: mtk-pmic-keys - add of_node_put() before return
  Input: sun4i-lradc-keys - add of_node_put() before return
  Input: synaptics - whitelist Lenovo T580 SMBus intertouch

Pull dma-mapping fixes from Christoph Hellwig:
 "Fix various regressions:

   - force unencrypted dma-coherent buffers if encryption bit can't fit
     into the dma coherent mask (Tom Lendacky)

   - avoid limiting request size if swiotlb is not used (me)

   - fix swiotlb handling in dma_direct_sync_sg_for_cpu/device (Fugang
     Duan)"

* tag 'dma-mapping-5.3-1' of git://git.infradead.org/users/hch/dma-mapping:
  dma-direct: correct the physical addr in dma_direct_sync_sg_for_cpu/device
  dma-direct: only limit the mapping size if swiotlb could be used
  dma-mapping: add a dma_addressing_limited helper
  dma-direct: Force unencrypted DMA under SME for certain DMA masks

Pull x86 fixes from Thomas Gleixner:
 "A set of x86 specific fixes and updates:

   - The CR2 corruption fixes which store CR2 early in the entry code
     and hand the stored address to the fault handlers.

   - Revert a forgotten leftover of the dropped FSGSBASE series.

   - Plug a memory leak in the boot code.

   - Make the Hyper-V assist functionality robust by zeroing the shadow
     page.

   - Remove a useless check for dead processes with LDT

   - Update paravirt and VMware maintainers entries.

   - A few cleanup patches addressing various compiler warnings"

* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/entry/64: Prevent clobbering of saved CR2 value
  x86/hyper-v: Zero out the VP ASSIST PAGE on allocation
  x86, boot: Remove multiple copy of static function sanitize_boot_params()
  x86/boot/compressed/64: Remove unused variable
  x86/boot/efi: Remove unused variables
  x86/mm, tracing: Fix CR2 corruption
  x86/entry/64: Update comments and sanity tests for create_gap
  x86/entry/64: Simplify idtentry a little
  x86/entry/32: Simplify common_exception
  x86/paravirt: Make read_cr2() CALLEE_SAVE
  MAINTAINERS: Update PARAVIRT_OPS_INTERFACE and VMWARE_HYPERVISOR_INTERFACE
  x86/process: Delete useless check for dead process with LDT
  x86: math-emu: Hide clang warnings for 16-bit overflow
  x86/e820: Use proper booleans instead of 0/1
  x86/apic: Silence -Wtype-limits compiler warnings
  x86/mm: Free sme_early_buffer after init
  x86/boot: Fix memory leak in default_get_smp_config()
  Revert "x86/ptrace: Prevent ptrace from clearing the FS/GS selector" and fix the test

Pull perf tooling updates from Thomas Gleixner:
 "A set of perf improvements and fixes:

  perf db-export:
   - Improvements in how COMM details are exported to databases for post
     processing and use in the sql-viewer.py UI.

   - Export switch events to the database.

  BPF:
   - Bump rlimit(MEMLOCK) for 'perf test bpf' and 'perf trace', just
     like selftests/bpf/bpf_rlimit.h do, which makes errors due to
     exhaustion of this limit, which are kinda cryptic (EPERM sometimes)
     less frequent.

  perf version:
   - Fix segfault due to missing OPT_END(), noticed on PowerPC.

  perf vendor events:
   - Add JSON files for IBM s/390 machine type 8561.

  perf cs-etm (ARM):
   - Fix two cases of error returns not bing done properly: Invalid
     ERR_PTR() use and loss of propagation error codes"

* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (28 commits)
  perf version: Fix segfault due to missing OPT_END()
  perf vendor events s390: Add JSON files for machine type 8561
  perf cs-etm: Return errcode in cs_etm__process_auxtrace_info()
  perf cs-etm: Remove errnoeous ERR_PTR() usage in cs_etm__process_auxtrace_info
  perf scripts python: export-to-postgresql.py: Export switch events
  perf scripts python: export-to-sqlite.py: Export switch events
  perf db-export: Export switch events
  perf db-export: Factor out db_export__threads()
  perf script: Add scripting operation process_switch()
  perf scripts python: exported-sql-viewer.py: Use new 'has_calls' column
  perf scripts python: exported-sql-viewer.py: Remove redundant semi-colons
  perf scripts python: export-to-postgresql.py: Add has_calls column to comms table
  perf scripts python: export-to-sqlite.py: Add has_calls column to comms table
  perf db-export: Also export thread's current comm
  perf db-export: Factor out db_export__comm()
  perf scripts python: export-to-postgresql.py: Export comm details
  perf scripts python: export-to-sqlite.py: Export comm details
  perf db-export: Export comm details
  perf db-export: Fix a white space issue in db_export__sample()
  perf db-export: Move export__comm_thread into db_export__sample()
  ...

Pull core fixes from Thomas Gleixner:

 - A collection of objtool fixes which address recent fallout partially
   exposed by newer toolchains, clang, BPF and general code changes.

 - Force USER_DS for user stack traces

[ Note: the "objtool fixes" are not all to objtool itself, but for
  kernel code that triggers objtool warnings.

  Things like missing function size annotations, or code that confuses
  the unwinder etc.   - Linus]

* 'core-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (27 commits)
  objtool: Support conditional retpolines
  objtool: Convert insn type to enum
  objtool: Fix seg fault on bad switch table entry
  objtool: Support repeated uses of the same C jump table
  objtool: Refactor jump table code
  objtool: Refactor sibling call detection logic
  objtool: Do frame pointer check before dead end check
  objtool: Change dead_end_function() to return boolean
  objtool: Warn on zero-length functions
  objtool: Refactor function alias logic
  objtool: Track original function across branches
  objtool: Add mcsafe_handle_tail() to the uaccess safe list
  bpf: Disable GCC -fgcse optimization for ___bpf_prog_run()
  x86/uaccess: Remove redundant CLACs in getuser/putuser error paths
  x86/uaccess: Don't leak AC flag into fentry from mcsafe_handle_tail()
  x86/uaccess: Remove ELF function annotation from copy_user_handle_tail()
  x86/head/64: Annotate start_cpu0() as non-callable
  x86/entry: Fix thunk function ELF sizes
  x86/kvm: Don't call kvm_spurious_fault() from .fixup
  x86/kvm: Replace vmx_vmenter()'s call to kvm_spurious_fault() with UD2
  ...