The BeagleBone Black is basically a regular BeagleBone with eMMC and
HDMI added, so create a common dtsi both can use.

IMPORTANT: booting the existing am335x-bone.dts will blow up the HDMI
transceiver after a dozen boots with an uSD card inserted because LDO
will be at 3.3V instead of 1.8.

MMC support for AM335x still isn't in, so only the LDO change has been
added.

Signed-off-by: Koen Kooi <koen@dominion.thruhere.net>
Tested-by: Tom Rini <trini@ti.com>
Tested-by: Matt Porter <matt.porter@linaro.org>
Acked-by: Kevin Hilman <khilman@linaro.org>
Tested-by: Kevin Hilman <khilman@linaro.org>
Tested-by: Joel Fernandes <joelf@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>

Add support for the imx6q wanboard variant.

Since imx6q/dl are pin to pin compatible, introduce the imx6qdl-wandboard.dtsi
file that contains the common peripheral nodes.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

Board files for Phytec phyCARD-S "System on Module" and "Rapid
Development Kit".

Based on patches from:

Steffen Trumtrar <s.trumtrar@pengutronix.de>:
 - Original patch
 - ARM: dts: Set partition offsets for phycard
 - ARM: dts: Use CSPI1 instead of CSPI2 on phycard pca100
 - ARM: imx27-phytec-phycard-S.dts: resize nand partitions

Jan Luebbe <jlu@pengutronix.de>:
 - ARM: dts: Enable bad block table in NAND

Cc: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Cc: Jan Luebbe <jlu@pengutronix.de>
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

The Cubieboard2 is the successor of the first Cubieboard, and shares the
same hardware, except that the Allwinner A10 found initially has been
replaced by an Allwinner A20.

Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

The Olimex A20-Olinuxino is an open-hardware board based on the
Allwinner A20 SoC, with most of the pins exported on headers, a 10/100M
ethernet port, SATA, SD and uSD slots, etc.

Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

This platform from WITS is the evaluation board for the Allwinner A31.
It features a quad-Cortex A7, 2048MB of RAM, NAND, USB, MMC, several
UART, HDMI, a 2048 x 1536 10" screen, powered by a PowerVR, etc.

Of course, most of these peripherals aren't supported yet, but support
for those will come eventually.

Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

The CFA-10058 is a breakout board for the CFA-10036 that has Ethernet, USB and a
5" LCD screen on it.

Signed-off-by: Brian Lilly <brian@crystalfontz.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

The CFA-10056 is a breakout board for the CFA-10036, and is
basically a CFA-10037, with a 4.3" screen.

Signed-off-by: Brian Lilly <brian@crystalfontz.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

The patch set beginning with commit:
"ARM: ux500: Apply a ste-* prefix onto snowball.dts"
thru commit:
"ARM: ux500: Remove u9540.dts as it's been replaced"
altered the names of the ux500 device tree files but forgot
to:

- Rename the ccu8540-pinctrl.dtsi file

- Update #include statements from files using these
  files, so the build broke.

- Update the Makefile for the device trees so the build
  broke.

Fix it up so we can build them all again.

Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>

This adds a device tree usable on Mele A1000 (and A2000, as it
apparently is the same device except for the case). This device features
one UART port, Ethernet, an AXP209 PMU on i2c0 and two user configurable
LEDs.

Signed-off-by: Emilio López <emilio@elopez.com.ar>
[maxime: fixed the soc node address]
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

This adds an initial DT file for the Globalscale D2Plug with Dove SoC.
Currently, one LED is missing and I have not been able to get SD8787 driver
working. Those will be taken care of later.

Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>

There are a number of variants of the ZyXEL NSA310, with slightly
different LEDs, buttons and i2c devices. Add a DTS file to support one
more of these variants.

Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Tibor Hársszegi <tibor@harsszegi.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>

The AXP WiFi AP board is a Marvell platform based on the Armada XP
MV78230 SoC. It has two mini-PCIe connectors, one USB 3.0 port powered
by a USB 3.0 controller on PCIe, two Ethernet ports, 1 GB of RAM, 1 GB
of NAND, 16 MB of SPI flash, one SATA port and one button, two UARTs

Successfully tested: USB 3.0 port, the mini-PCIe connectors, SPI
flash, Ethernet ports, SATA port, button, UART.

Untested: NAND flash, due to lack of mainline support for the Armada
370/XP NAND controller for now.

Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Tested-by: Seif Mazareeb <seif@marvell.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>

Add support for the BCM28155 AP board.

Signed-off-by: Markus Mayer <markus.mayer@linaro.org>
Acked-by: Christian Daudt <csd@broadcom.com>

This commit converts the mv88f6281gtw_ge Kirkwood board to use a
Device Tree representation, except for the Ethernet devices and the
DSA switch. Even though the mv643xx_eth driver has a DT binding,
converting this board to use it is for now left on the side because it
doesn't use a simple PHY, but a DSA switch instead.

Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>

All hardware parts of the (Armada 370 based) NETGEAR ReadyNAS 102 are
supported by mainline kernel (USB 3.0 rear ports, USB 2.0 front port,
Gigabit controller and PHY, serial port, leds, buttons, SATA ports,
G762 fan controller) except for:

 - the Intersil ISL12057 I2C RTC Chip,
 - the Armada NAND controller.

Support for both of those is currently work in progress and does not
prevent boot.

Signed-off-by: Arnaud Ebalard <arno@natisbad.org>
Acked-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>

This is in preparation for converting the marzen board to
use DT_MACHINE_START.

Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

This patch adds a sample DT-based Bock-W "reference" implementation.
The use of platform-specific C-code should be avoided
with this configuration as much as possible.

This patch adds new r8a7778_add_dt_devices() which was same stance
of r8a7790_add_dt_devices()

Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

This patch introduces device tree sources for Samsung Trats 2 board
based on Exynos4412 SoC.

Currently support includes:
 - eMMC,
 - main PMIC (max77686),
 - serial ports,
 - GPIO keys,
 - touchscreen.

Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>

Re-ordering in alphabetical.

Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>

Enable build of EMEV2 and KZM9D DT Reference in
case of ARCH_MULTIPLATFORM and ARCH_SHMOBILE_MULTI.

IS_ENABLED() is leaves the clock-emev2.c file out
in case of COMMON_CLK=y.

Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

This is sufficient to allow boot of the Lager board with
a console without boards-lager.c compiled into the kernel.
This is an example of a minimal but still useful initialisation
of the board using DT as much as possible.

As such it is the same as the boot of Lager that can be achieved
without a board file. The intention of adding this file
is to facilitate further work to allow board specific devices to be
initialised via DT.

Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

This patch adds a sample DT-based APE6EVM "reference" implementation. The
use of platform-specific C-code should be avoided with this configuration
as much as possible.

Signed-off-by: Guennadi Liakhovetski <g.liakhovetski+renesas@gmail.com>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Add a DT reference implementation for the KZM9D board.

Only DT devices are used in this case. UART, STI, GPIO
and SMP / GIC are all provided by emev2.dtsi.

There is still a board specific C file used for enabling
legacy SH clocks. This file will be removed after we have
moved over to common clocks.

Signed-off-by: Magnus Damm <damm@opensource.se>
[horms+renesas@verge.net.au: Do not include trailing blank line in
 board-kzm9d-reference.c ]
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Early upstream work on Tegra114 was performed on the Pluto board.
However, it's not used any more, and the DT doesn't contain anything
beyond a serial port, so the file isn't useful either. Remove it.

Signed-off-by: Stephen Warren <swarren@nvidia.com>

B2020 ADI board is reference board for STIH415/416 SOCs, it has 2 x
UART, 4x USB, 1 x Ethernet, 1 x SATA, 1 x PCIe, and 2GB RAM  with
standard set-top box IPs.

This patch adds initial support to B2020 with STiH415/416 with SBC_UART1
as console and a heard beat LED.

Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@st.com>
CC: Stephen Gallimore <stephen.gallimore@st.com>
CC: Stuart Menefy <stuart.menefy@st.com>
CC: Arnd Bergmann <arnd@arndb.de>

Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@st.com>
Signed-off-by: Olof Johansson <olof@lixom.net>

B2000 board is reference board for STIH415/416 SOCs, it has
2 x UART, 4x USB, 2 x Ethernet, 1 x SATA, 1 x PCIe, and 1GB RAM.

This patch add initial support to b2000 with STiH415/416 with UART2 as
console and a heard beat LED.

Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@st.com>
CC: Stephen Gallimore <stephen.gallimore@st.com>
CC: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Olof Johansson <olof@lixom.net>

This patch adds device trees for describing the TI-Nspire hardware.

Changes between v1 and v2:
* Change "keymap" binding to the standard "linux,keymap" binding.

Signed-off-by: Daniel Tang <dt.tangr@gmail.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>

Add AM43x ePOS EVM minimal DT source - this is a minimal one to get
it booting. Also include it in omap2plus dtbs and document bindings.
The hardware is under development.

Signed-off-by: Afzal Mohammed <afzal@ti.com>
Signed-off-by: Benoit Cousson <benoit.cousson@linaro.org>

Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Tested-by: Emilio López <emilio@elopez.com.ar>
Acked-by: Emilio López <emilio@elopez.com.ar>

The uevm is the only official board supported for the OMAP5 soc
in mainline. The existent sevm platform will no more be supported.
Hence cleaning up the board dts file to have only the data
required for uevm.

Renaming the board dts file and adding the following cleanups.

 * There are no devices connected on I2C 2,3,4 buses. So remove
   the pinmux data for the same.

 * OMAP5432 and DDR3 memory is used in the uevm. Temperature polling
   is not supported with DDR3 memories. Because of DDR3 phy limitation
   the voltage change across DVFS and all shadow registers for DVFS on
   DDR3 is not supported. Hence the emif kernel driver is not required,
   so removing the DDR3 device file and emif nodes for uevm.

 * Keypad is not supported on uevm. So remove the device node.

Signed-off-by: Sricharan R <r.sricharan@ti.com>
Signed-off-by: Benoit Cousson <benoit.cousson@linaro.org>

When making the dtbs target on OMAP/AM35xx, some trees are not
built.

Signed-off-by: Florian Vaussard <florian.vaussard@epfl.ch>
Signed-off-by: Benoit Cousson <benoit.cousson@linaro.org>

Add initial device tree nodes for EXYNOS5420 SoC and SMDK5420 board.

Signed-off-by: Chander Kashyap <chander.kashyap@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>

Add a DT fragment for the Zed Zynq platform and a corresponding
target to the Makefile

Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Reviewed-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>

Add a DT fragment for the zc706 Zynq platform and a corresponding
target to the Makefile.

Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Reviewed-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>

Add support for imx6q Phytec phyFLEX-i.MX6 Quad (aka pfla02 and pbab01).
 - Module pfla02
 - Carrier-Board pbab01

Signed-off-by: Christian Hemp <c.hemp@phytec.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

Patch adds initial dts for Phytec PCM970 Rapid development kit.
- Added definition for UART0 and UART1.
- Added additional SPI chipselect which used on RDK for ZegBee module.

Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

PCM038 dts can be used as base for development kit board or any
custom PCB designs. Renames this file to match functionality.

Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

Add initial Freescale Vybrid VF610 Tower board support
with uart and fec enabled.

Signed-off-by: Jingchang Lu <b35083@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

Add initial imx6sl-evk board support with uart, usdhc and fec enabled.

Signed-off-by: Shawn Guo <shawn.guo@linaro.org>