sirf uart and usp-based uart driver with full dma support has
hit 3.12, here we fix the fifosize, dma channels for some HW
prop.

Signed-off-by: Qipan Li <Qipan.Li@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Olof Johansson <olof@lixom.net>

This fixes a compile error where CONFIG_PCI is disabled:

  LD      init/built-in.o
arch/arm/mach-integrator/built-in.o: In function `ap_map_io':
integrator_cp.c:(.init.text+0x570): undefined reference to `pci_v3_early_init'
make[1]: *** [vmlinux] Error 1
make: *** [sub-make] Error 2

Cc: stable@vger.kernel.org
Signed-off-by: Joerg Roedel <joro@8bytes.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>

There appears to be an error in the second address of the second XOR
engine in the Kirkwood SoC device tree, which is specified as 0xd0b00
but should be 0x60b00.

For confirmation of address see table 581 page 658 of:

http://www.marvell.com/embedded-processors/kirkwood/assets/FS_88F6180_9x_6281_OpenSource.pdf



Also see definition of XOR1_HIGH_PHYS_BASE in
arch/arm/mach-kirkwood/include/mach/kirkwood.h

Signed-off-by: Quentin Armitage <quentin@armitage.org.uk>
Reviewed-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>

This flag is a NOOP since 2.6.36 and can be removed.

This is an update for 3.11 of a patch already sent for 3.10

Signed-off-by: Michael Opdenacker <michael.opdenacker@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>

Reported-by: Jiri Prchal <jiri.prchal@aksignal.cz>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>

Replace pinctrl_usart2_rts and pinctrl_usart2_cts istead of pinctrl_uart2_*.

Signed-off-by: Jiri Prchal <jiri.prchal@aksignal.cz>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>

If neither CONFIG_SND_DM365_AIC3X_CODEC nor CONFIG_SND_DM365_VOICE_CODEC
are defined, we may get warnings like:

    arch/arm/mach-davinci/board-dm365-evm.c:179:33: warning: 'dm365_evm_snd_data' defined but not used [-Wunused-variable]

To fix this, just mark the struct as __maybe_unused.

Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Cc: Sekhar Nori <nsekhar@ti.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Cc: Russell King <linux@arm.linux.org.uk>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>

commit fcf7157b

 ("ARM: davinci: serial: get rid of davinci_uart_config")
introduced build breakage because of a misplaced
header file include which cause a bunch of errors when
the file is included in assembly code (like debug-macro.S)

Fix the build breakage.

Reported-by: Alexander Holler <holler@ahsoftware.de>
Tested-by: Alexander Holler <holler@ahsoftware.de>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>

This is just a standard board for the Ux500, include it in the
v7 multiplatform defconfig.

Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>

Fix trivial typo in name.

Signed-off-by: Phil Carmody <phil.carmody@partner.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Corrected the functions spelling mistake in the OMAP4 SMP source file.

Signed-off-by: Anoop Thomas Mathew <atm@profoundis.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

We call cpu_cluster_pm_enter for dev->cpu == 0 only, but
cpu_cluster_pm_exit called without that check.

Because of that unhandled page fault may happen:

[    3.803405] Unable to handle kernel paging request at virtual address 00002500
[    3.810974] pgd = c0004000
[    3.813812] [00002500] *pgd=00000000
[    3.817596] Internal error: Oops: 5 [#1] SMP ARM
[    3.822418] Modules linked in:
[    3.825653] CPU: 1 PID: 0 Comm: swapper/1 Not tainted 3.11.0-rc6+ #21
[    3.832397] task: ed86ef40 ti: ed896000 task.ti: ed896000
[    3.838073] PC is at irq_notifier+0x234/0x25c
[    3.842651] LR is at irq_notifier+0x218/0x25c
[    3.847229] pc : [<c0029ed8>]    lr : [<c0029ebc>]    psr: 80000193
[    3.847229] sp : ed897ee8  ip : 00000005  fp : 00000001
[    3.859283] r10: c0b395f0  r9 : c0b30594  r8 : c0b8c2ac
[    3.864776] r7 : ffffffff  r6 : 00000000  r5 : 00000005  r4 : 00000000
[    3.871643] r3 : 00002500  r2 : 00000000  r1 : 00000005  r0 : 44302244
[    3.878479] Flags: Nzcv  IRQs off  FIQs on  Mode SVC_32  ISA ARM  Segment kernel
[    3.886260] Control: 10c5387d  Table: 8000404a  DAC: 00000015
[    3.892272] Process swapper/1 (pid: 0, stack limit = 0xed896240)
[    3.898590] Stack: (0xed897ee8 to 0xed898000)
[    3.903167] 7ee0:                   c0979c3a 00000001 ed897ef8 ed896000 c0014f7c 00000000
[    3.911743] 7f00: 00000005 00000000 ffffffff c0b8c2ac c0b395f0 c077c04c c0c94b48 c0b3953c
[    3.920318] 7f20: c0bcd928 00000002 c0b39524 c00cfad8 00000000 ffffffff 00000000 c00cfb10
[    3.928924] 7f40: c14e62c0 c002c1c8 c002c0ac c14e62c0 00000002 e251c37d 00000000 c0b39548
[    3.937499] 7f60: c0b395f0 c05a1bc4 e251c37d 00000000 00000005 c05a3870 edc90380 edc90380
[    3.946105] 7f80: edc90394 c14e62c0 c0b39548 00000002 c0784064 c05a3c78 c0b395e0 c14e62c0
[    3.954681] 7fa0: 00000002 c0b39548 c0bc9db8 00000000 00000001 c05a1dc0 ed896000 00000015
[    3.963287] 7fc0: c0bc9db8 ed896000 8000406a c0b30594 c0784064 c000e504 00000746 c007a528
[    3.971862] 7fe0: 00000001 0000001d 600001d3 c0bcc004 00000000 800086c4 ee0aa6a7 d2aabaa9
[    3.980499] [<c0029ed8>] (irq_notifier+0x234/0x25c) from [<c077c04c>] (notifier_call_chain+0x38/0x68)
[    3.990173] [<c077c04c>] (notifier_call_chain+0x38/0x68) from [<c00cfad8>] (cpu_pm_notify+0x20/0x38)
[    3.999786] [<c00cfad8>] (cpu_pm_notify+0x20/0x38) from [<c00cfb10>] (cpu_cluster_pm_exit+0x20/0x50)
[    4.009399] [<c00cfb10>] (cpu_cluster_pm_exit+0x20/0x50) from [<c002c1c8>] (omap_enter_idle_coupled+0x11c/0x14c)
[    4.020111] [<c002c1c8>] (omap_enter_idle_coupled+0x11c/0x14c) from [<c05a1bc4>] (cpuidle_enter_state+0x40/0xec)
[    4.030822] [<c05a1bc4>] (cpuidle_enter_state+0x40/0xec) from [<c05a3c78>] (cpuidle_enter_state_coupled+0x1f4/0x240)
[    4.041870] [<c05a3c78>] (cpuidle_enter_state_coupled+0x1f4/0x240) from [<c05a1dc0>] (cpuidle_idle_call+0x150/0x228)
[    4.052947] [<c05a1dc0>] (cpuidle_idle_call+0x150/0x228) from [<c000e504>] (arch_cpu_idle+0x8/0x38)
[    4.062499] [<c000e504>] (arch_cpu_idle+0x8/0x38) from [<c007a528>] (cpu_startup_entry+0x178/0x1e4)
[    4.071990] [<c007a528>] (cpu_startup_entry+0x178/0x1e4) from [<800086c4>] (0x800086c4)
[    4.080383] Code: e5922288 03a03b0a 13a03c25 e0823003 (e5932000)
[    4.086791] ---[ end trace d83954a84a6fa69e ]---

It is supposed that sar_base is initialized in irq_save_context, which
is called on CPU_CLUSTER_PM_ENTER notification. If this notification
has been missed and CPU_CLUSTER_PM_EXIT is received sar_base is NULL.

Fix it by calling CPU_CLUSTER_PM_{ENTER,EXIT} under the same condition.

Signed-off-by: Vladimir Murzin <murzin.v@gmail.com>
Acked-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>

When CONFIG_ARM_LPAE=y the following build warning is generated:

arch/arm/mach-omap2/gpmc.c:1495:4: warning: format '%x' expects argument of type 'unsigned int', but argument 4 has type 'resource_size_t' [-Wformat]

According to Documentation/printk-formats.txt '%pa' can be used to properly
print 'resource_size_t'.

Reported-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>

In case of error, the function omap_device_alloc() returns ERR_PTR()
and never returns NULL. The NULL test in the return value check
should be replaced with IS_ERR().

Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Acked-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Looks like we still have the legacy clock alias name for
omap4 GPMC (General Purpose Memory Controller), so let's
fix it for the device tree naming. There's no need to keep
the legacy naming as omap4 is DT only nowadays.

Without this fix we get the following error while booting:

[    0.440399] omap-gpmc 50000000.gpmc: error: clk_get

Reported-by: Olof Johansson <olof@lixom.net>
Cc: stable@vger.kernel.org # v3.11
Signed-off-by: Tony Lindgren <tony@atomide.com>

With the addition of the Armada XP reference clock, we can now model
accurately the available clock inputs for the timer: namely, nbclk
and refclk. For each of this clock inputs we assign a name, for the
driver to select as appropriate.

Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Reviewed-by: Mike Turquette <mturquette@linaro.org>
Acked-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>

The Armada XP SoC has a reference 25 MHz fixed-clock that is used in
some controllers such as the timer and the watchdog. This commit adds
a DT representation of this clock through a fixed-clock compatible node.

Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Reviewed-by: Mike Turquette <mturquette@linaro.org>
Acked-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>

The kirkwood.dtsi cpu@0 node is missing the mandatory reg property.
This causes of_get_cpu_node() to fail to find the node and as a result
the cpufreq driver fails in its probe function.

Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>

Add of_node_put to properly decrement the refcount when we are
done using a given node.

Signed-off-by: Jisheng Zhang <jszhang@marvell.com>
Reviewed-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>

Conflicts:
	arch/arm/mach-mvebu/armada-370-xp.c
	arch/arm/mach-mvebu/platsmp.c

Zaurus collie contains 2 LH28F640BFHE-PTTL90 (64M 4Mx16) and
at the moment cfi will not detect the collie NOR.
In the meanwhile we can revert to the jedec-probe map which has been
fixed with following commit:

mtd: jedec_probe: fix LH28F640BF definition
fe2f4c8e



Somehow this is unsatisfactory because the flash is mounted READ ONLY
(as from factory, with a RO cramfs)

Signed-off-by: Andrea Adami <andrea.adami@gmail.com>
Signed-off-by: Olof Johansson <olof@lixom.net>

Right now the U300 submenus are showcased for everyone even if
we're not on v5 multiplatforms. Hide this in the multiplatform
configuration properly.

Cc: arm@kernel.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>

Add pinmux configuration for MCBSP2 connected to the TDM interface.
With this configuration the Headset modules works as expected.

Signed-off-by: Enric Balletbo i Serra <eballetbo@gmail.com>
Acked-by: Javier Martinez Canillas <javier@dowhile0.org>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>

Commit 76787b3b

 (ARM: OMAP2+: Remove board-4430sdp.c)
removed legacy booting in favor of device tree based booting
for 4430sdp. That caused the WLAN to stop working as the
related .dts entries fell through the cracks.

I don't have the "1283 PG 2.21 connectivity device" on my 4430sdp,
but the earlier version of this patch was tested by Luciano
Coelho. This version has left out the input logic for MMC CLK
line compared to the earlier version as that is not bidirectional,
and should be safe to do.

Cc: Rajendra Nayak <rnayak@ti.com>
Cc: Luciano Coelho <luca@coelho.fi>
Cc: Ruslan Bilovol <ruslan.bilovol@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>

Commit b42b9181

 (ARM: OMAP2+: Remove board-omap4panda.c)
removed legacy booting in favor of device tree based booting
for pandaboard. That caused the WLAN to stop working as the
related .dts entries fell through the cracks.

The legacy muxing was setting pulls for GPIO 48 and 49, so let's
keep that behaviour for now to avoid further regressions for
BT and FM. Also input logic was enabled for MMC CLK line, but
I've verified that the input logic we don't need enabled for
CLK line as it's not bidirectional.

Also, we want to use non-removable instead of ti,non-removable
as the ti,non-removable also sets no_regulator_off_init which
is really not what we want as then wl12xx won't get powered
up and down which is needed for resetting it.

Note that looks like the WLAN interface fails to come up after
a warm reset, but that most likely was also happening with
the legacy booting and needs a separate fix.

Cc: Paolo Pisati <p.pisati@gmail.com>
Cc: Rajendra Nayak <rnayak@ti.com>
Cc: Luciano Coelho <luca@coelho.fi>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>

Without this, legacy platforms that can boot with a multiplatform
kernel but that need the DTB to be appended, won't have a way to pass
firmware-set bootargs to the kernel.

This is needed to boot multi_v7_defconfig on snowball, for instance.

Signed-off-by: Olof Johansson <olof@lixom.net>

This fixes a multiplatform regression on the Ux500.

When compiling the Ux500 platforms in multiplatform configurations
both PL310_ERRATA_588369 and PL310_ERRATA_727915 would crash the
platform when trying to launch the init process.

The Ux500 cannot access the debug registers of the PL310, it will
just crash if you try this. So disable this by setting the debug
callback to NULL when initializing the l2x0 on this platform.

Cc: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>

Fix the DTS data for ocp2scp node by adding the
missing reg property.

Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>

USB3 block has a 64KiB space, another 64KiB is
used for the wrapper.

Without this change, resource_size() will get
confused and driver won't probe because size
will be negative.

Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>

The BeagleBone Black is basically a regular BeagleBone with eMMC and
HDMI added, so create a common dtsi both can use.

IMPORTANT: booting the existing am335x-bone.dts will blow up the HDMI
transceiver after a dozen boots with an uSD card inserted because LDO
will be at 3.3V instead of 1.8.

MMC support for AM335x still isn't in, so only the LDO change has been
added.

Signed-off-by: Koen Kooi <koen@dominion.thruhere.net>
Tested-by: Tom Rini <trini@ti.com>
Tested-by: Matt Porter <matt.porter@linaro.org>
Acked-by: Kevin Hilman <khilman@linaro.org>
Tested-by: Kevin Hilman <khilman@linaro.org>
Tested-by: Joel Fernandes <joelf@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>

The beagle and beagle-xm entries were inside the same double quote.
Split them to have two distinct entries.

Signed-off-by: Robert Nelson <robertcnelson@gmail.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>

The patch "0b7a76aa

 ARM: dts: imx6q{dl}: add DTE pads for uart"
adds the DTE pads for uart. For PAD_EIM_D29, the offset of the
Pad Mux register should be 0x0c8, not 0x0c4.

This patch fixes it.

Signed-off-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

The L2 cache controller(PL310) version on the i.MX6D/Q is r3p1-50rel0
The L2 cache controller(PL310) version on the i.MX6DL/SOLO/SL is r3p2
But according to ARM PL310 errata: 752271
ID: 752271: Double linefill feature can cause data corruption
Fault Status: Present in: r3p0, r3p1, r3p1-50rel0. Fixed in r3p2
Workaround: The only workaround to this erratum is to disable the
double linefill feature. This is the default behavior.

without this patch, you will meet the following error when run the
memtester application at: http://pyropus.ca/software/memtester/



FAILURE: 0x00100000 != 0x00200000 at offset 0x01365664.
FAILURE: 0x00100000 != 0x00200000 at offset 0x01365668.
FAILURE: 0x00100000 != 0x00200000 at offset 0x0136566c.
FAILURE: 0x00100000 != 0x00200000 at offset 0x01365670.
FAILURE: 0x00100000 != 0x00200000 at offset 0x01365674.
FAILURE: 0x00100000 != 0x00200000 at offset 0x01365678.

Signed-off-by: Jason Liu <r64343@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

Commit 718a3500 (ARM: i.MX51: Add PATA support) adds pata support to the
imx51.dtsi file and is using clock 161. The problem is that the right
clock is 172, according to commit 5d530bb0

 (ARM: i.MX5: Add PATA and SRTC
clocks).  Using the clock 172 makes things work again (and kills a nasty
system freeze).

Tested-by: Steev Klimaszewski <steev@gentoo.org>
Signed-off-by: Arnaud Patard <arnaud.patard@rtp-net.org>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

Since commit beb2d1c1

 (ARM i.MX5: Add S/PDIF clocks), the following clock
error appears on mx51:

TrustZone Interrupt Controller (TZIC) initialized
i.MX51 clk 180: register failed with -17
i.MX5 clk 180: register failed with -17
sched_clock: 32 bits at 24MHz, resolution 41ns, wraps every 178956ms
CPU identified as i.MX51, silicon rev 3.0
...

Clock 180 corresponds to 'spdif1_podf' and this clock is getting registered
twice.

Fix it, by properly registering the 'spdif1_pred' clock, which should not
reference 'spdif1_podf'.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

The clk_init_data.flags of clk-fixup-mux is left there without
initialization.  It may hold some random data and cause clock framework
interpret the clock in an unexpected way.  At least on imx6sl, the
following division by zero error with sched_clock is seen because of it.

Division by zero in kernel.
CPU: 0 PID: 0 Comm: swapper/0 Not tainted 3.11.0-rc3+ #19
Backtrace:
[<80011af0>] (dump_backtrace+0x0/0x10c) from [<80011c90>] (show_stack+0x18/0x1c)
 r6:3b9aca00 r5:00000020 r4:00000000 r3:00000000
[<80011c78>] (show_stack+0x0/0x1c) from [<8055e02c>] (dump_stack+0x78/0x94)
[<8055dfb4>] (dump_stack+0x0/0x94) from [<80011924>] (__div0+0x18/0x20)
 r4:00000000 r3:00000000
[<8001190c>] (__div0+0x0/0x20) from [<8026c408>] (Ldiv0_64+0x8/0x18)
[<8006330c>] (clocks_calc_mult_shift+0x0/0xf8) from [<8072f604>] (setup_sched_clock+0x88/0x1f0)
[<8072f57c>] (setup_sched_clock+0x0/0x1f0) from [<8071ad48>] (mxc_timer_init+0xe8/0x17c)
[<8071ac60>] (mxc_timer_init+0x0/0x17c) from [<807290b0>] (imx6sl_clocks_init+0x1db8/0x1dc0)
 r8:807a9ca4 r7:00000000 r6:80777564 r5:8100c1f4 r4:c0820000
[<807272f8>] (imx6sl_clocks_init+0x0/0x1dc0) from [<807420ac>] (of_clk_init+0x40/0x6c)
[<8074206c>] (of_clk_init+0x0/0x6c) from [<807290cc>] (imx6sl_timer_init+0x14/0x18)
 r5:807a8e80 r4:ffffffff
[<807290b8>] (imx6sl_timer_init+0x0/0x18) from [<80716e1c>] (time_init+0x24/0x34)
[<80716df8>] (time_init+0x0/0x34) from [<80713738>] (start_kernel+0x1b0/0x310)
[<80713588>] (start_kernel+0x0/0x310) from [<80008074>] (0x80008074)
 r7:80770b08 r6:80754cd4 r5:8076c8c4 r4:10c53c7d
sched_clock: 32 bits at 0 Hz, resolution 0ns, wraps every 0ms

Fix the bug by initializing init.flags as zero.

Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

CSPI PER clock is per2clk (per2_gate id 60) instead of cspiX_ipg_gate.

Signed-off-by: Gwenhael Goavec-Merou <gwenhael.goavec-merou@armadeus.com>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

Commit 567b21e9


"mips: convert vpe_class to use dev_groups"

broke the build on MIPS since vpe_attrs should be an array
of 'struct device_attribute' pointers.

Fixes the following build problem:
arch/mips/kernel/vpe.c:1372:2: error: missing braces around initializer
[-Werror=missing-braces]
arch/mips/kernel/vpe.c:1372:2: error: (near initialization for 'vpe_attrs[0]')
[-Werror=missing-braces]

Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: John Crispin <blogic@openwrt.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/5819/


Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

After the last architecture switched to generic hard irqs the config
options HAVE_GENERIC_HARDIRQS & GENERIC_HARDIRQS and the related code
for !CONFIG_GENERIC_HARDIRQS can be removed.

Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>

The TCBIND register is only available if the core has MT support. It
should not be read otherwise. Secondly, the number of TCs (siblings)
are calculated differently depending on if the kernel is configured
as SMVP or SMTC.

Signed-off-by: Leonid Yegoshin <Leonid.Yegoshin@imgtec.com>
Signed-off-by: Steven J. Hill <Steven.Hill@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/5822/


Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

This change complements commit d0da7c002f7b2a93582187a9e3f73891a01d8ee4
and brings clear_ioasic_irq back, renaming it to clear_ioasic_dma_irq at
the same time, to make I/O ASIC DMA interrupts functional.

Unlike ordinary I/O ASIC interrupts DMA interrupts need to be deasserted
by software by writing 0 to the respective bit in I/O ASIC's System
Interrupt Register (SIR), similarly to how CP0.Cause.IP0 and CP0.Cause.IP1
bits are handled in the CPU (the difference is SIR DMA interrupt bits are
R/W0C so there's no need for an RMW cycle).  Otherwise the handler is
reentered over and over again.

The only current user is the DEC LANCE Ethernet driver and its extremely
uncommon DMA memory error handler that does not care when exactly the
interrupt is cleared.  Anticipating the use of DMA interrupts by the Zilog
SCC driver this change however exports clear_ioasic_dma_irq for device
drivers to choose the right application-specific sequence to clear the
request explicitly rather than calling it implicitly in the .irq_eoi
handler of `struct irq_chip'.  Previously these interrupts were cleared in
the .end handler of the said structure, before it was removed.

Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/5826/


Signed-off-by: Ralf Baechle <ralf@linux-mips.org>