fixes unused variable warning.

Reported-by: Eric Biggers <ebiggers@kernel.org>
Acked-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Mikita Lipski <mikita.lipski@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Make the fw_write_wait default case true since presumably all new
gfx9 asics will have updated firmware. That is using unique WAIT_REG_MEM
packet with opration=1.

Signed-off-by: Aaron Liu <aaron.liu@amd.com>
Tested-by: Aaron Liu <aaron.liu@amd.com>
Tested-by: Yuxian Dai <Yuxian.Dai@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Acked-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org

For Arcturus, forcing clock to some specific level is not supported
with 54.18 and onwards SMU firmware. As according to firmware team,
they adopt new gfx dpm tuned parameters which can cover all the use
case in a much smooth way. Thus setting through driver interface
is not needed and maybe do a disservice.

Signed-off-by: Evan Quan <evan.quan@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

The system will be hang up during S3 suspend because of SMU is pending
for GC not respose the register CP_HQD_ACTIVE access request.This issue
root cause of accessing the GC register under enter GFX CGGPG and can
be fixed by disable GFX CGPG before perform suspend.

v2: Use disable the GFX CGPG instead of RLC safe mode guard.

Signed-off-by: Prike Liang <Prike.Liang@amd.com>
Tested-by: Mengbing Wang <Mengbing.Wang@amd.com>
Reviewed-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org

[WHY]
In cases where a clock table is malformed such that fclk entries have
frequencies but not voltages listed, we don't catch the error and set
clocks to 0 instead of using hardcoded values as we should.

[HOW]
Add check for clock tables fclk entry's voltage as well

Signed-off-by: Michael Strauss <michael.strauss@amd.com>
Reviewed-by: Eric Yang <eric.yang2@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org

[Why]
If dc->clk_mgr->funcs->are_clock_states_equal is set, then
wm_optimized_required is never checked. In that case, when going from a
higher mode to a lower mode, wm_optimized_required remains true until
the next mode change.

[How]
 - move from else-if to unconditional or

Signed-off-by: Joshua Aberback <joshua.aberback@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Reviewed-by: Yongqiang Sun <yongqiang.sun@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

[Why]
In some usecases, like tiled display, the stream and plane configuration
can be setup in a way where the caller expects DAL to perform the
clipping, eg:

P0:
src_rect(0, 0, w, h)
dst_rect(0, 0, w, h)

P1:
src_rect(w, 0, w, h)
dst_rect(0, 0, w, h)

Cursor is enabled on both streams with the same position.

This can result in double cursor on tiled display, even though this
behavior is technically correct from the DC interface point of view.

We need a mechanism to control this dynamically.

[How]
This is something that should live in the DM layer based on detection
of the specified configuration but it's not something that we really
have enough information to deal with today.

Add a flag to the cursor position state that specifies whether we
want DC to do the translation or not and make it opt-in and let
the DM decide when to do it.

Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

[Why]
If a plane isn't being actively enabled or disabled then DC won't
always recalculate scaling rects and ratios for the primary plane.

This results in only a partial or corrupted rect being displayed on
the screen instead of scaling to fit the screen.

[How]
Add back the logic to recalculate the scaling rects into
dc_commit_updates_for_stream since this is the expected place to
do it in DC.

This was previously removed a few years ago to fix an underscan issue
but underscan is still functional now with this change - and it should
be, since this is only updating to the latest plane state getting passed
in.

Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

[Why]
For medium updates that change nothing but the source rect position
the viewport doesn't change on DCN20.

We're missing the check for the position update bit that was there in
the DCN10 hardware sequencer.

[How]
Check the position bit along with the scaling bit like we were doing
with DCN20.

We shouldn't actually hit a case where context != current_state in
our programming/commit model but guard against it anyway since it was
guarded for the other bits.

Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Zhan Liu <Zhan.Liu@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

[Why]
Cursor pos is correctly adjusted from DC side for source rect offset
on DCN ASIC, but only on the overlay.

This is because DM places offsets the cursor for primary planes only
to workaround missing code in DCE for the adjustment we're now correctly
doing in DC for DCN ASIC.

[How]
Drop the adjustment for source rect from the DM side of things and put
the code where it actually belongs - in DC on the pipe level.

This matches what we do for DCN now.

Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Zhan Liu <Zhan.Liu@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

[Why]
Changing policy to dynamic will allow 4k multi display configs
to be supported at DPM0

Signed-off-by: Eric Yang <Eric.Yang2@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

[Why]
Cursor is drawn as part of the framebuffer for a plane on AMD hardware.
The cursor position on the framebuffer does not change even if the
source rect viewport for the cursor does. This causes the cursor to be
clipped.

The following IGT tests fail as a result of this issue:

- kms_plane_cursor@pipe-*-viewport-size-*

[How]
Offset cursor position by plane source rect viewport. If the viewport
is unscaled then the cursor is now correctly positioned on any
plane - primary or overlay.

There is still a hardware limitation for dealing with the cursor size
being incorrectly scaled but that's not something we can address.

Add some documentation explaining some of this in the code while we're
at it.

Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Zhan Liu <Zhan.Liu@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

[Why]
After v_total_min and max are updated in vrr structure, the changes are
not reflected in stream adjust. When these values are read from stream
adjust it does not reflect the actual state of the system.

[How]
Set stream adjust values equal to vrr adjust values after vrr adjust
values are updated.

Signed-off-by: Isabel Zhang <isabel.zhang@amd.com>
Reviewed-by: Alvin Lee <Alvin.Lee2@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

[Why]
Prop are created at boot stage, and not allowed to create new prop
after device registration.

[How]
Reuse the connector property from SST if exist.

Signed-off-by: Jerry (Fangzhi) Zuo <Jerry.Zuo@amd.com>
Reviewed-by: Hersen Wu <hersenxs.wu@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Replace dev_warn() with dev_info() and note that they are
optional to avoid confusing users.

The RAS TAs only exist on server boards and the HDCP and DTM
TAs only exist on client boards.  They are optional either way.

Acked-by: Nirmoy Das <nirmoy.das@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

prefix RAS error related dmesg print with pci device info

Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: John Clements <john.clements@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

upon receiving uncorrectable error, query every GPU node for ras errors

Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: John Clements <john.clements@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Incorrect CG sequence will cause gfx timedout,
if we keep switching power profile mode
(enter profile mod such as PEAK will disable CG,
exit profile mode EXIT will enable CG)
when run Vulkan test case(case used for test: vkexample).

Signed-off-by: Chengming Gui <Jack.Gui@amd.com>
Reviewed-by: Kenneth Feng <kenneth.feng@amd.com>
Acked-by: Evan Quan <evan.quan@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

On ARCTURUS and RENOIR, powerplay is not supported yet.
When plug in or unplug power jack, ACPI event will issue.
Then kernel NULL pointer BUG will be triggered.
Check for NULL pointers before calling.

Signed-off-by: Aaron Ma <aaron.ma@canonical.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org

Change SH_MEM_CONFIG Alignment mode to Automatic, as:
1)OGL fn_amd_compute_shader will failed with unaligned mode.
2)The default alignment mode was defined to automatic on gfx10
specification.

Signed-off-by: Likun Gao <Likun.Gao@amd.com>
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

hwmgr->pm_en is initialized at hwmgr_hw_init.
during amdgpu_device_init, there is amdgpu_asic_reset that calls to
pp_get_asic_baco_capability, while hwmgr->pm_en has not yet been initialized.

so avoid using pm_en in pp_get_asic_baco_capability.

Reviewed-by: Emily Deng <Emily.Deng@amd.com>
Signed-off-by: Tiecheng Zhou <Tiecheng.Zhou@amd.com>
Signed-off-by: Yintian Tao <yttao@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

As the pmfw hasn't exported the interface of SMU feature
mask to APU SKU so just force on all the features to driver
inquired interface at early initial stage.

Signed-off-by: Prike Liang <Prike.Liang@amd.com>
Reviewed-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org

Fixes build error of:
"use of undeclared identifier 'RENOIR_A0'"

To fix the same, this patch re-orders the
ASIC declarations accordingly.

Fixes: 41ef3dcd

 ("drm/amd/display: Fix RV2 Variant Detection")
Signed-off-by: Shirish S <shirish.s@amd.com>
Reviewed-by: Zhan Liu <zhan.liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

1.Using the FCLK DPM table to set the MCLK for DPM states consist of
three entities:
 FCLK
 UCLK
 MEMCLK
All these three clk change together, MEMCLK from FCLK, so use the fclk
frequency.
2.we should show the current working clock freqency from clock table metric

Signed-off-by: Yuxian Dai <Yuxian.Dai@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Huang Rui <ray.huang@amd.com>
Reviewed-by: Kevin Wang <Kevin1.Wang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org

Originally, it kfrees the wrong pointer for mem_obj.
It would cause memory leak under stress test.

Signed-off-by: Jack Zhang <Jack.Zhang1@amd.com>
Acked-by: Nirmoy Das <nirmoy.das@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

[Why]
Some displays have an issue where the hdcp chips are initialized after the
display has already lit up. This means we can sometimes authentication too early
and cause authentication failures.

This happens when HDCP is enabled and the display is power cycled. Normally we
will authenticate 2 seconds after the display is lit, but some displays need a
bit more time.

[How]
Increase delay to 3 second before we start authentication.

Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

[Why]
-We need to cancel future callbacks/watchdogs events when a callback/watchdog event happens

[How]
-fix typo in event_callback()
	-cancel callback, not watchdog
-cancel watchdog events in event_watchdog_timer().

Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

[Why]
When content type property is set to 1. We should enable hdcp2.2 and if we cant
then stop. Currently the way it works in DC is that if we fail hdcp2, we will
try hdcp1 after.

[How]
Use link config to force disable hdcp1.4 when type1 is set.

Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

This is ASIC specific and should be placed in _ppt.c of each ASIC.

Signed-off-by: Evan Quan <evan.quan@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

This is already done in soc15.c. And this is really ASIC specific
and should not be placed here.

Signed-off-by: Evan Quan <evan.quan@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

[Why]
DML expects num_states to exclude the duplicate state.

[How]
Set num_states to correct value to prevent array off-by-one error.  Also
refactor max clock level code for diags.

Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Signed-off-by: George Shen <george.shen@amd.com>
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

[Why]
BT2020 is not supported in COLOR_ENCODING property of planes.  Only
BT601 and BT709 was available.

[How]
Allow BT2020 as legit value in setting COLOR_ENCODING property.

Signed-off-by: Stylon Wang <stylon.wang@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

[Why]
Nominal pixel clock and EDID information differ in precision so although
monitor reports maximum refresh is 2x minimum, LFC was not being
enabled.

[How]
Use minimum refresh rate as nominal/2 when EDID dictates that min
refresh = max refresh/2.

v2: squash in 64 bit divide fix

Signed-off-by: Aric Cyr <aric.cyr@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

[Why]
CTM was only supported at CRTC level and we need color space conversion
in linear space at plane level.

[How]
- Add plane-level CTM to dc interface
- Program plane-level CTM in DCN

Signed-off-by: Stylon Wang <stylon.wang@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

[Why]
Change is causing a regression where the OPC app no longer functions
properly.

[How]
Revert the changelist causing the issue.

Signed-off-by: Isabel Zhang <isabel.zhang@amd.com>
Reviewed-by: Yongqiang Sun <yongqiang.sun@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

[Why]
In some scenario like 1366x768 VSR enabled connected with a 4K monitor
and playing 4K video in clone mode, underflow will be observed due to
decrease dppclk when previouse surface scan isn't finished

[How]
In this use case, surface flip is switching between 4K and 1366x768,
1366x768 needs smaller dppclk, and when decrease the clk and previous
surface scan is for 4K and scan isn't done, underflow will happen.  Not
doing optimize bandwidth in case of flip pending.

Signed-off-by: Yongqiang Sun <yongqiang.sun@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

[Why]
For some monitors extreme flickering can occur while using LFC for if
we're not doing the DRR timing update for V_TOTAL_MIN / V_TOTAL_MAX at
the DP start of frame.

Hardware can default to any time in the frame which isn't the behavior
we want.

[How]
Add a new function for setting the double buffering mode for DRR timing.

Default to DP start of frame double buffering on timing generator init.

Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

[Why]
P010 pixel format is not declared as supported in DRM and DM.

[How]
Add P010 format to the support list presented to DRM and checked in DM

Signed-off-by: Stylon Wang <stylon.wang@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

[Why]
Diagnostics scaling test failing to set required number of vertical taps
in 4:2:0 surface case

[How]
In dpp3_get_optimal_number_of_taps() need to use LB_MEMORY_CONFIG_3 for
4:2:0 surface case. In resource_build_scaling_params() make sure to also
set plane res alpha enable based on updated surface state

Signed-off-by: Eric Bernstein <eric.bernstein@amd.com>
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

the HPD bo size calculation error.
the "mem.size" can't present actual BO size all time.

Signed-off-by: Kevin Wang <kevin1.wang@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Acked-by: Christian König <Christian.Koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>