- Jun 10, 2019
-
-
Tony Lindgren authored
Some older interconnect target modules need module internal clock toggling quirks to reset properly. We've been doing this in the platform code earlier, but need to be able to it directly in the ti-sysc driver when we no longer rely on on the platform code. Let's add reset handling for 1-wire, i2c and watchdog. Later on we can add more modules like msdi and dss as they get tested. For dra7 pcie, we should be able to just use the rstctrl reset driver when available. Signed-off-by:
Tony Lindgren <tony@atomide.com>
-
- May 28, 2019
-
-
Tony Lindgren authored
Looks like we currently only detect UART on omap36xx, let's also add support for omap34xx. And let's also fix the SWSUP mode, it should be SWSUP_SIDLE for omap3, not SWSUP_SIDLE_ACT like for omap4 and later. Note that we are still booting omap3 for most part without ti-sysc, so no need to treat this change as a fix. Tested-by:
Keerthy <j-keerthy@ti.com> Signed-off-by:
Tony Lindgren <tony@atomide.com>
-
Tony Lindgren authored
We need to deassert rstctrl resets before enabling clocks to avoid clock "failed to enable" errors. For asserting rstctrl reset, the clocks need to be enabled. As the reset controller status is not available for arrays, let's use devm_reset_control_get_optional() so we can get the status after reset. Note that depends on a proper PRM rstctrl driver, so far I've only tested this with earlier reset-simple patches. Tested-by:
Keerthy <j-keerthy@ti.com> Signed-off-by:
Tony Lindgren <tony@atomide.com>
-
Tony Lindgren authored
We must not assert reset for modules with no child device drivers until in runtime_suspend. Otherwise register access will fail without legacy mode helping us. Let's add a flag for disable_on_idle and move the reset driver handling to runtime suspend and resume. We can then also use the disable_on_idle flag to reconfigure sysconfig register for PM modes requesting it. Let's also make the other flags use bitfield while at it instead of bool. Tested-by:
Keerthy <j-keerthy@ti.com> Signed-off-by:
Tony Lindgren <tony@atomide.com>
-
Tony Lindgren authored
Some modules have ENAWAKEUP bit that we need to configure when not relying on platform data callbacks. Tested-by:
Keerthy <j-keerthy@ti.com> Signed-off-by:
Tony Lindgren <tony@atomide.com>
-
Tony Lindgren authored
Some modules have idlemodes wired, but not completely functional. We have quirks for SWSUP_SIDLE and SWSUP_SIDLE_ACT to manage interconnect target modules without hardware support, but we've been only using them so far in legacy mode. Let's add support for SWSUP quirks in non-legacy mode too. Tested-by:
Keerthy <j-keerthy@ti.com> Signed-off-by:
Tony Lindgren <tony@atomide.com>
-
Tony Lindgren authored
Modules with clockactivity need it configured during enable. Tested-by:
Keerthy <j-keerthy@ti.com> Signed-off-by:
Tony Lindgren <tony@atomide.com>
-
Tony Lindgren authored
For interconnect target modules with autoidle bit wired, we need to manage it for enable and disable. Tested-by:
Keerthy <j-keerthy@ti.com> Signed-off-by:
Tony Lindgren <tony@atomide.com>
-
Tony Lindgren authored
We need to specify QUIRK_LEGACY_IDLE for device drivers that still have pm_runtime_irq_safe() set like 8250. Tested-by:
Keerthy <j-keerthy@ti.com> Signed-off-by:
Tony Lindgren <tony@atomide.com>
-
Tony Lindgren authored
We've had minimal OCP softreset support in ti-sysc interconnect target module driver only used for MCAN driver so far. But it turns out that MCAN has the sysstatus register resetdone bit inverted compared to most other modules. Let's make OCP softreset work for other typical cases with reset status in sysstatus or sysconfig register so we can use the new functions for sysc_enable_module() and sysc_disable_module() without "ti,hwmods" property in the following patches. Tested-by:
Keerthy <j-keerthy@ti.com> Signed-off-by:
Tony Lindgren <tony@atomide.com>
-
Tony Lindgren authored
We need to also support 16-bit writes for i2c in addition to the reads when we start configuring the sysconfig register for reset and idle modes. Note that only i2c revision register has LO and HI registers, so let's add a check also for 16-bit register read. This change is currently cosmetic and does not affect anything until we enable the module specific quirk handling for i2c reset and enable later on. Signed-off-by:
Tony Lindgren <tony@atomide.com>
-
Tony Lindgren authored
We need to let ti-sysc driver manage clockdomain autoidle for the duration of of reset, enable and idle. And we need to do it before we enable the clock and after we disable it. Currently we are still relying on platform callbacks indirectly managing clockdomain autoidle. But I noticed that for device tree only probed drivers it now happens only after we enabling the clocks and before we disable the clocks, while it should be the other way around. So far I have not noticed any issues with this though. Let's add new ti_sysc_clkdm_deny_idle() and ti_sysc_clkdm_allow_idle() functions for ti-sysc driver to use to manage clockdomains directly via platform data callbacks. Note that we can implement the clockdomain functions in pdata-quirks.c as for probing devices without "ti,hwmods" custom property we don't need to use the other platform data callbacks. Let's do this in one patch as there's is still an unlikely chance we may need to apply this as a fix for v5.2 for dropping legacy platform data for some devices. We also do have the option of adding back the platform data if needed in case of trouble. Tested-by:
Keerthy <j-keerthy@ti.com> Signed-off-by:
Tony Lindgren <tony@atomide.com>
-
- May 20, 2019
-
-
Tony Lindgren authored
-
Tony Lindgren authored
-
Keerthy authored
usb4_tm is unsed on dra71 and accessing the module with ti,sysc is causing a boot crash hence disable its target module. Fixes: 549fce06 ("ARM: dts: dra7: Add l4 interconnect hierarchy and ti-sysc data") Signed-off-by:
Keerthy <j-keerthy@ti.com> Signed-off-by:
Tony Lindgren <tony@atomide.com>
-
Keerthy authored
Introduce dra71x.dtsi to include dra71x specific changes. rtc is fused out on dra71 and accessing target module register is causing a boot crash hence disable it. Fixes: 549fce06 ("ARM: dts: dra7: Add l4 interconnect hierarchy and ti-sysc data") Signed-off-by:
Keerthy <j-keerthy@ti.com> Signed-off-by:
Tony Lindgren <tony@atomide.com>
-
Keerthy authored
usb4_tm is unsed on dra76 and accessing the module with ti,sysc is causing a boot crash hence disable its target module. Fixes: 549fce06 ("ARM: dts: dra7: Add l4 interconnect hierarchy and ti-sysc data") Signed-off-by:
Keerthy <j-keerthy@ti.com> Signed-off-by:
Tony Lindgren <tony@atomide.com>
-
Keerthy authored
rtc is fused out on dra76 and accessing target module register is causing a boot crash hence disable it. Fixes: 549fce06 ("ARM: dts: dra7: Add l4 interconnect hierarchy and ti-sysc data") Signed-off-by:
Keerthy <j-keerthy@ti.com> Signed-off-by:
Tony Lindgren <tony@atomide.com>
-
Linus Torvalds authored
-
git://git.kernel.org/pub/scm/linux/kernel/git/rw/ubifsLinus Torvalds authored
Pull UBIFS fixes from Richard Weinberger: - build errors wrt xattrs - mismerge which lead to a wrong Kconfig ifdef - missing endianness conversion * tag 'upstream-5.2-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/rw/ubifs: ubifs: Convert xattr inum to host order ubifs: Use correct config name for encryption ubifs: Fix build error without CONFIG_UBIFS_FS_XATTR
-
Linus Torvalds authored
Merge yet more updates from Andrew Morton: "A few final bits: - large changes to vmalloc, yielding large performance benefits - tweak the console-flush-on-panic code - a few fixes" * emailed patches from Andrew Morton <akpm@linux-foundation.org>: panic: add an option to replay all the printk message in buffer initramfs: don't free a non-existent initrd fs/writeback.c: use rcu_barrier() to wait for inflight wb switches going into workqueue when umount mm/compaction.c: correct zone boundary handling when isolating pages from a pageblock mm/vmap: add DEBUG_AUGMENT_LOWEST_MATCH_CHECK macro mm/vmap: add DEBUG_AUGMENT_PROPAGATE_CHECK macro mm/vmalloc.c: keep track of free blocks for vmap allocation
-
git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuildLinus Torvalds authored
Pull more Kbuild updates from Masahiro Yamada: - remove unneeded use of cc-option, cc-disable-warning, cc-ldoption - exclude tracked files from .gitignore - re-enable -Wint-in-bool-context warning - refactor samples/Makefile - stop building immediately if syncconfig fails - do not sprinkle error messages when $(CC) does not exist - move arch/alpha/defconfig to the configs subdirectory - remove crappy header search path manipulation - add comment lines to .config to clarify the end of menu blocks - check uniqueness of module names (adding new warnings intentionally) * tag 'kbuild-v5.2-2' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild: (24 commits) kconfig: use 'else ifneq' for Makefile to improve readability kbuild: check uniqueness of module names kconfig: Terminate menu blocks with a comment in the generated config kbuild: add LICENSES to KBUILD_ALLDIRS kbuild: remove 'addtree' and 'flags' magic for header search paths treewide: prefix header search paths with $(srctree)/ media: prefix header search paths with $(srctree)/ media: remove unneeded header search paths alpha: move arch/alpha/defconfig to arch/alpha/configs/defconfig kbuild: terminate Kconfig when $(CC) or $(LD) is missing kbuild: turn auto.conf.cmd into a mandatory include file .gitignore: exclude .get_maintainer.ignore and .gitattributes kbuild: add all Clang-specific flags unconditionally kbuild: Don't try to add '-fcatch-undefined-behavior' flag kbuild: add some extra warning flags unconditionally kbuild: add -Wvla flag unconditionally arch: remove dangling asm-generic wrappers samples: guard sub-directories with CONFIG options kbuild: re-enable int-in-bool-context warning MAINTAINERS: kbuild: Add pattern for scripts/*vmlinux* ...
-
git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linuxLinus Torvalds authored
Pull i2c updates from Wolfram Sang: "Some I2C core API additions which are kind of simple but enhance error checking for users a lot, especially by returning errno now. There are wrappers to still support the old API but it will be removed once all users are converted" * 'i2c/for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: i2c: core: add device-managed version of i2c_new_dummy i2c: core: improve return value handling of i2c_new_device and i2c_new_dummy
-
git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4Linus Torvalds authored
Pull ext4 fixes from Ted Ts'o: "Some bug fixes, and an update to the URL's for the final version of Unicode 12.1.0" * tag 'ext4_for_linus_stable' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4: ext4: avoid panic during forced reboot due to aborted journal ext4: fix block validity checks for journal inodes using indirect blocks unicode: update to Unicode 12.1.0 final unicode: add missing check for an error return from utf8lookup() ext4: fix miscellaneous sparse warnings ext4: unsigned int compared against zero ext4: fix use-after-free in dx_release() ext4: fix data corruption caused by overlapping unaligned and aligned IO jbd2: fix potential double free ext4: zero out the unused memory region in the extent tree block
-
git://git.samba.org/sfrench/cifs-2.6Linus Torvalds authored
Pull cifs fixes from Steve French: "Minor cleanup and fixes, one for stable, four rdma (smbdirect) related. Also adds SEEK_HOLE support" * tag '5.2-rc-smb3-fixes' of git://git.samba.org/sfrench/cifs-2.6: cifs: add support for SEEK_DATA and SEEK_HOLE Fixed https://bugzilla.kernel.org/show_bug.cgi?id=202935 allow write on the same file cifs: Allocate memory for all iovs in smb2_ioctl cifs: Don't match port on SMBDirect transport cifs:smbd Use the correct DMA direction when sending data cifs:smbd When reconnecting to server, call smbd_destroy() after all MIDs have been called cifs: use the right include for signal_pending() smb3: trivial cleanup to smb2ops.c cifs: cleanup smb2ops.c and normalize strings smb3: display session id in debug data
-
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tipLinus Torvalds authored
Pull perf tooling updates from Ingo Molnar: "perf.data: - Streaming compression of perf ring buffer into PERF_RECORD_COMPRESSED user space records, resulting in ~3-5x perf.data file size reduction on variety of tested workloads what saves storage space on larger server systems where perf.data size can easily reach several tens or even hundreds of GiBs, especially when profiling with DWARF-based stacks and tracing of context switches. perf record: - Improve -user-regs/intr-regs suggestions to overcome errors perf annotate: - Remove hist__account_cycles() from callback, speeding up branch processing (perf record -b) perf stat: - Add a 'percore' event qualifier, e.g.: -e cpu/event=0,umask=0x3,percore=1/, that sums up the event counts for both hardware threads in a core. We can already do this with --per-core, but it's often useful to do this together with other metrics that are collected per hardware thread. I.e. now its possible to do this per-event, and have it mixed with other events not aggregated by core. arm64: - Map Brahma-B53 CPUID to cortex-a53 events. - Add Cortex-A57 and Cortex-A72 events. csky: - Add DWARF register mappings for libdw, allowing --call-graph=dwarf to work on the C-SKY arch. x86: - Add support for recording and printing XMM registers, available, for instance, on Icelake. - Add uncore_upi (Intel's "Ultra Path Interconnect" events) JSON support. UPI replaced the Intel QuickPath Interconnect (QPI) in Xeon Skylake-SP. Intel PT: - Fix instructions sampling rate. - Timestamp fixes. - Improve exported-sql-viewer GUI, allowing, for instance, to copy'n'paste the trees, useful for e-mailing" * 'perf-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (73 commits) perf stat: Support 'percore' event qualifier perf stat: Factor out aggregate counts printing perf tools: Add a 'percore' event qualifier perf docs: Add description for stderr perf intel-pt: Fix sample timestamp wrt non-taken branches perf intel-pt: Fix improved sample timestamp perf intel-pt: Fix instructions sampling rate perf regs x86: Add X86 specific arch__intr_reg_mask() perf parse-regs: Add generic support for arch__intr/user_reg_mask() perf parse-regs: Split parse_regs perf vendor events arm64: Add Cortex-A57 and Cortex-A72 events perf vendor events arm64: Map Brahma-B53 CPUID to cortex-a53 events perf vendor events arm64: Remove [[:xdigit:]] wildcard perf jevents: Remove unused variable perf test zstd: Fixup verbose mode output perf tests: Implement Zstd comp/decomp integration test perf inject: Enable COMPRESSED record decompression perf report: Implement perf.data record decompression perf record: Implement -z,--compression_level[=<n>] option perf report: Add stub processing of compressed events for -D ...
-
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tipLinus Torvalds authored
Pull clocksource updates from Ingo Molnar: "Misc clocksource/clockevent driver updates that came in a bit late but are ready for v5.2" * 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: misc: atmel_tclib: Do not probe already used TCBs clocksource/drivers/timer-atmel-tcb: Convert tc_clksrc_suspend|resume() to static clocksource/drivers/tcb_clksrc: Rename the file for consistency clocksource/drivers/timer-atmel-pit: Rework Kconfig option clocksource/drivers/tcb_clksrc: Move Kconfig option ARM: at91: Implement clocksource selection clocksource/drivers/tcb_clksrc: Use tcb as sched_clock clocksource/drivers/tcb_clksrc: Stop depending on atmel_tclib ARM: at91: move SoC specific definitions to SoC folder clocksource/drivers/timer-milbeaut: Cleanup common register accesses clocksource/drivers/timer-milbeaut: Add shutdown function clocksource/drivers/timer-milbeaut: Fix to enable one-shot timer clocksource/drivers/tegra: Rework for compensation of suspend time clocksource/drivers/sp804: Add COMPILE_TEST to CONFIG_ARM_TIMER_SP804 clocksource/drivers/sun4i: Add a compatible for suniv dt-bindings: timer: Add Allwinner suniv timer
-
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tipLinus Torvalds authored
Pull IRQ chip updates from Ingo Molnar: "A late irqchips update: - New TI INTR/INTA set of drivers - Rewrite of the stm32mp1-exti driver as a platform driver - Update the IOMMU MSI mapping API to be RT friendly - A number of cleanups and other low impact fixes" * 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (34 commits) iommu/dma-iommu: Remove iommu_dma_map_msi_msg() irqchip/gic-v3-mbi: Don't map the MSI page in mbi_compose_m{b, s}i_msg() irqchip/ls-scfg-msi: Don't map the MSI page in ls_scfg_msi_compose_msg() irqchip/gic-v3-its: Don't map the MSI page in its_irq_compose_msi_msg() irqchip/gicv2m: Don't map the MSI page in gicv2m_compose_msi_msg() iommu/dma-iommu: Split iommu_dma_map_msi_msg() in two parts genirq/msi: Add a new field in msi_desc to store an IOMMU cookie arm64: arch_k3: Enable interrupt controller drivers irqchip/ti-sci-inta: Add msi domain support soc: ti: Add MSI domain bus support for Interrupt Aggregator irqchip/ti-sci-inta: Add support for Interrupt Aggregator driver dt-bindings: irqchip: Introduce TISCI Interrupt Aggregator bindings irqchip/ti-sci-intr: Add support for Interrupt Router driver dt-bindings: irqchip: Introduce TISCI Interrupt router bindings gpio: thunderx: Use the default parent apis for {request,release}_resources genirq: Introduce irq_chip_{request,release}_resource_parent() apis firmware: ti_sci: Add helper apis to manage resources firmware: ti_sci: Add RM mapping table for am654 firmware: ti_sci: Add support for IRQ management firmware: ti_sci: Add support for RM core ops ...
-
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tipLinus Torvalds authored
Pull EFI fix from Ingo Molnar: "Fix an EFI-fb regression that affects certain x86 systems" * 'efi-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: fbdev/efifb: Ignore framebuffer memmap entries that lack any memory types
-
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tipLinus Torvalds authored
Pull core fixes from Ingo Molnar: "This fixes a particularly thorny munmap() bug with MPX, plus fixes a host build environment assumption in objtool" * 'core-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: objtool: Allow AR to be overridden with HOSTAR x86/mpx, mm/core: Fix recursive munmap() corruption
-
git://git.kernel.org/pub/scm/linux/kernel/git/soc/socLinus Torvalds authored
Pull ARM SoC late updates from Olof Johansson: "This is some material that we picked up into our tree late. Most of it are smaller fixes and additions, some defconfig updates due to recent development, etc. Code-wise the largest portion is a series of PM updates for the at91 platform, and those have been in linux-next a while through the at91 tree before we picked them up" * tag 'armsoc-late' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (29 commits) arm64: dts: sprd: Add clock properties for serial devices Opt out of scripts/get_maintainer.pl ARM: ixp4xx: Remove duplicated include from common.c soc: ixp4xx: qmgr: Fix an NULL vs IS_ERR() check in probe arm64: tegra: Disable XUSB support on Jetson TX2 arm64: tegra: Enable SMMU translation for PCI on Tegra186 arm64: tegra: Fix insecure SMMU users for Tegra186 arm64: tegra: Select ARM_GIC_PM amba: tegra-ahb: Mark PM functions as __maybe_unused ARM: dts: logicpd-som-lv: Fix MMC1 card detect ARM: mvebu: drop return from void function ARM: mvebu: prefix coprocessor operand with p ARM: mvebu: drop unnecessary label ARM: mvebu: fix a leaked reference by adding missing of_node_put ARM: socfpga_defconfig: enable LTC2497 ARM: mvebu: kirkwood: remove error message when retrieving mac address ARM: at91: sama5: make ov2640 as a module ARM: OMAP1: ams-delta: fix early boot crash when LED support is disabled ARM: at91: remove HAVE_FB_ATMEL for sama5 SoC as they use DRM soc/fsl/qe: Fix an error code in qe_pin_request() ...
-
git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linuxLinus Torvalds authored
Pull powerpc fixes from Michael Ellerman: "One fix going back to stable, for a bug on 32-bit introduced when we added support for THREAD_INFO_IN_TASK. A fix for a typo in a recent rework of our hugetlb code that leads to crashes on 64-bit when using hugetlbfs with a 4K PAGE_SIZE. Two fixes for our recent rework of the address layout on 64-bit hash CPUs, both only triggered when userspace tries to access addresses outside the user or kernel address ranges. Finally a fix for a recently introduced double free in an error path in our cacheinfo code. Thanks to: Aneesh Kumar K.V, Christophe Leroy, Sachin Sant, Tobin C. Harding" * tag 'powerpc-5.2-2' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux: powerpc/cacheinfo: Remove double free powerpc/mm/hash: Fix get_region_id() for invalid addresses powerpc/mm: Drop VM_BUG_ON in get_region_id() powerpc/mm: Fix crashes with hugepages & 4K pages powerpc/32s: fix flush_hash_pages() on SMP
-
git://git.kernel.org/pub/scm/linux/kernel/git/mips/linuxLinus Torvalds authored
Pull a few more MIPS updates from Paul Burton: "Some SGI IP27 specific PCI rework and a batch of fixes: - A build fix for BMIPS5000 configurations with CONFIG_HW_PERF_EVENTS=y, which also neatly removes some #ifdefery. - A fix to report supported ISAs correctly on older Ingenic SoCs which incorrectly indicate MIPSr2 support in their cop0 Config register. - Some PCI modernization for SGI IP27 systems as part of ongoing work to support some other SGI systems. - A fix allowing use of appended DTB files with generic kernels. - DMA mask fixes for SGI IP22 & Alchemy systems" * tag 'mips_5.2_2' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux: MIPS: Alchemy: add DMA masks for on-chip ethernet MIPS: SGI-IP22: provide missing dma_mask/coherent_dma_mask generic: fix appended dtb support MIPS: SGI-IP27: abstract chipset irq from bridge MIPS: SGI-IP27: use generic PCI driver MIPS: Fix Ingenic SoCs sometimes reporting wrong ISA MIPS: perf: Fix build with CONFIG_CPU_BMIPS5000 enabled
-
Linus Torvalds authored
Merge tag 'riscv-for-linus-5.2-mw2' of git://git.kernel.org/pub/scm/linux/kernel/git/palmer/riscv-linux Pull RISC-V updates from Palmer Dabbelt: "This contains an assortment of RISC-V related patches that I'd like to target for the 5.2 merge window. Most of the patches are cleanups, but there are a handful of user-visible changes: - The nosmp and nr_cpus command-line arguments are now supported, which work like normal. - The SBI console no longer installs itself as a preferred console, we rely on standard mechanisms (/chosen, command-line, hueristics) instead. - sfence_remove_sfence_vma{,_asid} now pass their arguments along to the SBI call. - Modules now support BUG(). - A missing sfence.vma during boot has been added. This bug only manifests during boot. - The arch/riscv support for SiFive's L2 cache controller has been merged, which should un-block the EDAC framework work. I've only tested this on QEMU again, as I didn't have time to get things running on the Unleashed. The latest master from this morning merges in cleanly and passes the tests as well" * tag 'riscv-for-linus-5.2-mw2' of git://git.kernel.org/pub/scm/linux/kernel/git/palmer/riscv-linux: (31 commits) riscv: fix locking violation in page fault handler RISC-V: sifive_l2_cache: Add L2 cache controller driver for SiFive SoCs RISC-V: Add DT documentation for SiFive L2 Cache Controller RISC-V: Avoid using invalid intermediate translations riscv: Support BUG() in kernel module riscv: Add the support for c.ebreak check in is_valid_bugaddr() riscv: support trap-based WARN() riscv: fix sbi_remote_sfence_vma{,_asid}. riscv: move switch_mm to its own file riscv: move flush_icache_{all,mm} to cacheflush.c tty: Don't force RISCV SBI console as preferred console RISC-V: Access CSRs using CSR numbers RISC-V: Add interrupt related SCAUSE defines in asm/csr.h RISC-V: Use tabs to align macro values in asm/csr.h RISC-V: Fix minor checkpatch issues. RISC-V: Support nr_cpus command line option. RISC-V: Implement nosmp commandline option. RISC-V: Add RISC-V specific arch_match_cpu_phys_id riscv: vdso: drop unnecessary cc-ldoption riscv: call pm_power_off from machine_halt / machine_power_off ...
-
- May 19, 2019
-
-
Masahiro Yamada authored
'ifeq ... else ifneq ... endif' notation is supported by GNU Make 3.81 or later, which is the requirement for building the kernel since commit 37d69ee3 ("docs: bump minimal GNU Make version to 3.81"). Use it to improve the readability. Signed-off-by:
Masahiro Yamada <yamada.masahiro@socionext.com>
-
Feng Tang authored
Currently on panic, kernel will lower the loglevel and print out pending printk msg only with console_flush_on_panic(). Add an option for users to configure the "panic_print" to replay all dmesg in buffer, some of which they may have never seen due to the loglevel setting, which will help panic debugging . [feng.tang@intel.com: keep the original console_flush_on_panic() inside panic()] Link: http://lkml.kernel.org/r/1556199137-14163-1-git-send-email-feng.tang@intel.com [feng.tang@intel.com: use logbuf lock to protect the console log index] Link: http://lkml.kernel.org/r/1556269868-22654-1-git-send-email-feng.tang@intel.com Link: http://lkml.kernel.org/r/1556095872-36838-1-git-send-email-feng.tang@intel.com Signed-off-by:
Feng Tang <feng.tang@intel.com> Reviewed-by:
Petr Mladek <pmladek@suse.com> Cc: Aaro Koskinen <aaro.koskinen@nokia.com> Cc: Petr Mladek <pmladek@suse.com> Cc: Steven Rostedt <rostedt@goodmis.org> Cc: Sergey Senozhatsky <sergey.senozhatsky.work@gmail.com> Cc: Kees Cook <keescook@chromium.org> Cc: Borislav Petkov <bp@suse.de> Signed-off-by:
Andrew Morton <akpm@linux-foundation.org> Signed-off-by:
Linus Torvalds <torvalds@linux-foundation.org>
-
Steven Price authored
Since commit 54c7a891 ("initramfs: free initrd memory if opening /initrd.image fails"), the kernel has unconditionally attempted to free the initrd even if it doesn't exist. In the non-existent case this causes a boot-time splat if CONFIG_DEBUG_VIRTUAL is enabled due to a call to virt_to_phys() with a NULL address. Instead we should check that the initrd actually exists and only attempt to free it if it does. Link: http://lkml.kernel.org/r/20190516143125.48948-1-steven.price@arm.com Fixes: 54c7a891 ("initramfs: free initrd memory if opening /initrd.image fails") Signed-off-by:
Steven Price <steven.price@arm.com> Reported-by:
Mark Rutland <mark.rutland@arm.com> Tested-by:
Mark Rutland <mark.rutland@arm.com> Reviewed-by:
Mike Rapoport <rppt@linux.ibm.com> Cc: Christoph Hellwig <hch@lst.de> Signed-off-by:
Andrew Morton <akpm@linux-foundation.org> Signed-off-by:
Linus Torvalds <torvalds@linux-foundation.org>
-
Jiufei Xue authored
synchronize_rcu() didn't wait for call_rcu() callbacks, so inode wb switch may not go to the workqueue after synchronize_rcu(). Thus previous scheduled switches was not finished even flushing the workqueue, which will cause a NULL pointer dereferenced followed below. VFS: Busy inodes after unmount of vdd. Self-destruct in 5 seconds. Have a nice day... BUG: unable to handle kernel NULL pointer dereference at 0000000000000278 evict+0xb3/0x180 iput+0x1b0/0x230 inode_switch_wbs_work_fn+0x3c0/0x6a0 worker_thread+0x4e/0x490 ? process_one_work+0x410/0x410 kthread+0xe6/0x100 ret_from_fork+0x39/0x50 Replace the synchronize_rcu() call with a rcu_barrier() to wait for all pending callbacks to finish. And inc isw_nr_in_flight after call_rcu() in inode_switch_wbs() to make more sense. Link: http://lkml.kernel.org/r/20190429024108.54150-1-jiufei.xue@linux.alibaba.com Signed-off-by:
Jiufei Xue <jiufei.xue@linux.alibaba.com> Acked-by:
Tejun Heo <tj@kernel.org> Suggested-by:
Tejun Heo <tj@kernel.org> Cc: <stable@vger.kernel.org> Signed-off-by:
Andrew Morton <akpm@linux-foundation.org> Signed-off-by:
Linus Torvalds <torvalds@linux-foundation.org>
-
Mel Gorman authored
syzbot reported the following error from a tree with a head commit of baf76f0c ("slip: make slhc_free() silently accept an error pointer") BUG: unable to handle kernel paging request at ffffea0003348000 #PF error: [normal kernel read fault] PGD 12c3f9067 P4D 12c3f9067 PUD 12c3f8067 PMD 0 Oops: 0000 [#1] PREEMPT SMP KASAN CPU: 1 PID: 28916 Comm: syz-executor.2 Not tainted 5.1.0-rc6+ #89 Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011 RIP: 0010:constant_test_bit arch/x86/include/asm/bitops.h:314 [inline] RIP: 0010:PageCompound include/linux/page-flags.h:186 [inline] RIP: 0010:isolate_freepages_block+0x1c0/0xd40 mm/compaction.c:579 Code: 01 d8 ff 4d 85 ed 0f 84 ef 07 00 00 e8 29 00 d8 ff 4c 89 e0 83 85 38 ff ff ff 01 48 c1 e8 03 42 80 3c 38 00 0f 85 31 0a 00 00 <4d> 8b 2c 24 31 ff 49 c1 ed 10 41 83 e5 01 44 89 ee e8 3a 01 d8 ff RSP: 0018:ffff88802b31eab8 EFLAGS: 00010246 RAX: 1ffffd4000669000 RBX: 00000000000cd200 RCX: ffffc9000a235000 RDX: 000000000001ca5e RSI: ffffffff81988cc7 RDI: 0000000000000001 RBP: ffff88802b31ebd8 R08: ffff88805af700c0 R09: 0000000000000000 R10: 0000000000000000 R11: 0000000000000000 R12: ffffea0003348000 R13: 0000000000000000 R14: ffff88802b31f030 R15: dffffc0000000000 FS: 00007f61648dc700(0000) GS:ffff8880ae900000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: ffffea0003348000 CR3: 0000000037c64000 CR4: 00000000001426e0 Call Trace: fast_isolate_around mm/compaction.c:1243 [inline] fast_isolate_freepages mm/compaction.c:1418 [inline] isolate_freepages mm/compaction.c:1438 [inline] compaction_alloc+0x1aee/0x22e0 mm/compaction.c:1550 There is no reproducer and it is difficult to hit -- 1 crash every few days. The issue is very similar to the fix in commit 6b0868c8 ("mm/compaction.c: correct zone boundary handling when resetting pageblock skip hints"). When isolating free pages around a target pageblock, the boundary handling is off by one and can stray into the next pageblock. Triggering the syzbot error requires that the end of pageblock is section or zone aligned, and that the next section is unpopulated. A more subtle consequence of the bug is that pageblocks were being improperly used as migration targets which potentially hurts fragmentation avoidance in the long-term one page at a time. A debugging patch revealed that it's definitely possible to stray outside of a pageblock which is not intended. While syzbot cannot be used to verify this patch, it was confirmed that the debugging warning no longer triggers with this patch applied. It has also been confirmed that the THP allocation stress tests are not degraded by this patch. Link: http://lkml.kernel.org/r/20190510182124.GI18914@techsingularity.net Fixes: e332f741 ("mm, compaction: be selective about what pageblocks to clear skip hints") Signed-off-by:
Mel Gorman <mgorman@techsingularity.net> Reported-by:
<syzbot+d84c80f9fe26a0f7a734@syzkaller.appspotmail.com> Cc: Dmitry Vyukov <dvyukov@google.com> Cc: Andrey Ryabinin <aryabinin@virtuozzo.com> Cc: Qian Cai <cai@lca.pw> Cc: Michal Hocko <mhocko@suse.com> Cc: Vlastimil Babka <vbabka@suse.cz> Cc: <stable@vger.kernel.org> # v5.1+ Signed-off-by:
Andrew Morton <akpm@linux-foundation.org> Signed-off-by:
Linus Torvalds <torvalds@linux-foundation.org>
-
Uladzislau Rezki (Sony) authored
This macro adds some debug code to check that vmap allocations are happened in ascending order. By default this option is set to 0 and not active. It requires recompilation of the kernel to activate it. Set to 1, compile the kernel. [urezki@gmail.com: v4] Link: http://lkml.kernel.org/r/20190406183508.25273-4-urezki@gmail.com Link: http://lkml.kernel.org/r/20190402162531.10888-4-urezki@gmail.com Signed-off-by:
Uladzislau Rezki (Sony) <urezki@gmail.com> Reviewed-by:
Roman Gushchin <guro@fb.com> Cc: Ingo Molnar <mingo@elte.hu> Cc: Joel Fernandes <joelaf@google.com> Cc: Matthew Wilcox <willy@infradead.org> Cc: Michal Hocko <mhocko@suse.com> Cc: Oleksiy Avramchenko <oleksiy.avramchenko@sonymobile.com> Cc: Steven Rostedt <rostedt@goodmis.org> Cc: Tejun Heo <tj@kernel.org> Cc: Thomas Garnier <thgarnie@google.com> Cc: Thomas Gleixner <tglx@linutronix.de> Signed-off-by:
Andrew Morton <akpm@linux-foundation.org> Signed-off-by:
Linus Torvalds <torvalds@linux-foundation.org>
-