This results in a nice cleanup :)

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

The ehci1/ohci1 pair on the ba10-tv-box is connected to an USB-2 wifi
module soldered on the PCB, so there enabling ohci1 is not necessary.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

The polaroid-mid2809 tablet has an esp8089 wifi chip,
add a dt node describing it.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

The polaroid-mid2407 tablet has an esp8089 wifi chip,
add a dt node describing it.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

A23/A33 has a NAND controller which can now be used properly.

Add a device node for it.

The DMA function cannot work because of changed DMA IP block, so it's
temporarily removed in the device node. However, with PIO mode it can still
work.

Tested on an Aoson M751s tablet with Boris Brezillon's "mtd: nand: allow
vendor specific detection/initialization" patchset, which is needed for the
large-block MLC chip to be recognized correctly.
( http://lists.infradead.org/pipermail/linux-mtd/2016-June/068198.html

 )

Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

Add a dts file for tablets using the generic inet-q972 PCB.

Tablets with this PCB feature a mini-hdmi output, micro-usb usb-host,
micro-usb usb-otg, 3.5mm headphone jack, a micro sd slot,
(mini) power-barrel and an usb wifi module.

This has been tested on a 9.7" 1024x768 qware qw tb9718-qhd tablet.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

Just like with a13/a23/a33 most a31 tablets are derived from the same
reference design. Add a .dtsi file with all the common bits to avoid
endless copy and pasting of these.

The sun6i-reference-design-tablet.dtsi this commit adds is a copy
of sun6i-a31s-colorfly-e708-q1.dts with a few tablet specific bits
removed / left in sun6i-a31s-colorfly-e708-q1.dts.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

The presence of the mma8452_int_e708_q1 node is a copy and paste
error, remove it.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

The 32.768 kHz clock inside the A80 SoC is fed from an external source,
typically the AC100 RTC module.

Make the osc32k placeholder a fixed-factor clock so board dts files can
specify its source.

Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

Almost all sun8i tablets use a gsl1680 touchscreen controller, so add
a node describing it to reference-design-tablet.dtsi.

Almost all, but not all, so mark it as disabled by default (dts files
will also need to supply a firmware-name and resolution info).

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

The ga10h tablet has a rtl8703as wifi chip, add a dt node describing it.

This enables usage of wifi on this tablet (together with the out of
tree rtl8732bs driver).

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

This results in quite a nice cleanup for this dts file.

As an added bonus this also enables full otg support. I've tested that
this works as advertised.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

The Orange Pi Lite SBC is a small H3 based SBC, with 512MB RAM,
micro-sd slot, HDMI out, 2 USB-A connectors, 1 micro-USB connector,
sdio attached rtl8189ftv wifi and an ir receiver.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

A33-OLinuXino is A33 development board designed by Olimex LTD.

It has AXP223 PMU, 1GB DRAM, a micro SD card, one USB-OTG connector,
headphone and mic jacks, connector for LiPo battery and optional
4GB NAND Flash.

It has two 40-pin headers. One for LCD panel, and one for
additional modules. Also there is CSI/DSI connector.

Signed-off-by: Stefan Mavrodiev <stefan.mavrodiev@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

The CHIP has a status LED connected to one of the AXP GPIOs. Add the
gpio-leds node to be able to use the proper LED framework to control it.

Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

Add the AXP209 GPIO node to our AXP209 DTSI so that boards can use it.

Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>

This will allow u-boot to fill in a mac-address for Orange Pi 2
variants which use an sdio wifi without an eeprom for the mac.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

There is a new Orange Pi PC *Plus* version available now,
this is an extended version of the regular Orange Pi PC
with sdio wifi and an eMMC.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
[Maxime: Fix model and compatible]
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

Now that we've all the necessary bits in place we can enable
full otg support on these tablets.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

This commit adds definition for cpu_on, cpu_off and cpu_suspend
commands.  These definitions must match the corresponding PSCI
definitions in boot monitor.

Having those command and corresponding PSCI support in boot monitor
allows run time CPU hot plugin.

Link: http://lkml.kernel.org/r/E1b8koV-0004Hf-2j@rmk-PC.armlinux.org.uk


Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Vitaly Andrianov <vitalya@ti.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Cc: Pratyush Anand <panand@redhat.com>
Cc: Eric Biederman <ebiederm@xmission.com>
Cc: Dave Young <dyoung@redhat.com>
Cc: Baoquan He <bhe@redhat.com>
Cc: Vivek Goyal <vgoyal@redhat.com>
Cc: Simon Horman <horms@verge.net.au>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Replace the non-standard vendor prefix stm with st for
STMicroelectronics. The drivers do not specify the vendor prefixes
since the I2C Core strips them away from the DT provided compatible
string. Therefore, changing existing device trees does not have any
impact on device detection.

Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Rob Herring <robh@kernel.org>

The inet86dz board is a board used in 7" tablets from various oems.

These tablets are a23 based 7" tablets featuring a 1024x600 LCD,
512MB RAM, 4G NAND, rtl8188etv usb wifi, gsl1680 touchschreen,
micro-sd slot, 3.5mm headphone jack and a micro-usb otg connector
which doubles as charging port.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

The Polaroid MID2407PXE03 is an a23 based 7" tablet based on a M86_MB V2.0
PCB, featuring a 800x480 LCD, 512MB RAM, 4G NAND, esp8089 wifi, gsl1680
touchschreen, micro-sd slot, 3.5mm headphone jack and a micro-usb otg
connector which doubles as charging port.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

This results in quite a nice cleanup for this dts file.

As an added bonus this also enables backlight, regulator and full otg
support. I've tested that all these works as advertised.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

This results in quite a nice cleanup for this dts file.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

Add a drivevbus-supply property so that the drivevbus regulator
reports the right voltage value.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

Copy sun8i-q8-common.dtsi to sun8i-reference-design-tablet.dtsi. This
is part of renaming all the sun?i-q8-common.dtsi files to
sun?i-reference-design-tablet.dtsi since most of the hw-config in there
is shared by all sunxi tablets.

Note that in this case we keep sun5i-q8-common.dtsi as it is shared
between a23 / a33 q8 tablets. Also we leave the usb-wifi config in
there (rather then in sun8i-reference-design-tablet.dtsi) as most
sun8i tablets use sdio wifi rather then usb wifi.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

This results in a nice cleanup for this dts file.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

This results in quite a nice cleanup for this dts file.

Note as a side-effect this also enables the on board speaker / headphones
out. I've tested that this works as advertised.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

Remove all mention of q8 from sun5i-reference-design-tablet.dtsi.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

Set lradc vref to the actual avcc ldo, rather then to the fixed 3v0
regulator from common-regulators.dtsi.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

Rename sun5i-q8-common.dtsi to sun5i-reference-design-tablet.dtsi. This
is part of renaming all the sun?i-q8-common.dtsi files to
sun?i-reference-design-tablet.dtsi since most of the hw-config in there
is shared by all sunxi tablets.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

This is a preparation patch for renaming sun5i-q8-common.dtsi to
sun5i-reference-design-tablet.dtsi and sharing it between all
the A13 tablet dts files.

Since we only have a panel config for the 18 tablets (for now) move
this to the q8 specific dts file.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

Rename sunxi-q8-common.dtsi to sunxi-reference-design-tablet.dtsi. This
is part of renaming all the sun?i-q8-common.dtsi files to
sun?i-reference-design-tablet.dtsi since most of the hw-config in there
is shared by all sunxi tablets.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

Commit 0dfd582e

 ("watchdog: qcom: use timer devicetree
binding") moved to use the watchdog as a subset timer
register block. Some devices have the watchdog completely
standalone with slightly different register offsets as
well so let's account for the differences here.

The existing "kpss-standalone" compatible string doesn't
make it entirely clear exactly what the device is so
rename to "kpss-wdt" to reflect watchdog timer
functionality. Also update ipq4019 DTS with an SoC
specific compatible.

Signed-off-by: Matthew McClintock <mmcclint@codeaurora.org>
Signed-off-by: Thomas Pedersen <twp@codeaurora.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>

Update the compatible string to align with driver and also
add SoC specific string to DTS.

CC: linux-watchdog@vger.kernel.org
Signed-off-by: Matthew McClintock <mmcclint@codeaurora.org>
Signed-off-by: Thomas Pedersen <twp@codeaurora.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>

Building both ARMv4 and ARMv5 dtbs when SOC_SAM_V4_V5 is an issue for
kernelci because it will then attempt to boot ARMv4 kernels on at91sam9
which doesn't work.

Use CONFIG_SOC_AT91RM9200 and CONFIG_SOC_AT91SAM9 instead.

Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>

Separate the definitions for the emac and the gmac in different files and
include them in the final board dts that uses them.

Solves:
Warning (unit_address_vs_reg): Node /ahb/apb/ethernet@f0028000 has a unit name, but no reg property
Warning (unit_address_vs_reg): Node /ahb/apb/ethernet@f802c000 has a unit name, but no reg property

Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>