This results in a nice cleanup :)

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

The ehci1/ohci1 pair on the ba10-tv-box is connected to an USB-2 wifi
module soldered on the PCB, so there enabling ohci1 is not necessary.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

The polaroid-mid2809 tablet has an esp8089 wifi chip,
add a dt node describing it.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

The polaroid-mid2407 tablet has an esp8089 wifi chip,
add a dt node describing it.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

A23/A33 has a NAND controller which can now be used properly.

Add a device node for it.

The DMA function cannot work because of changed DMA IP block, so it's
temporarily removed in the device node. However, with PIO mode it can still
work.

Tested on an Aoson M751s tablet with Boris Brezillon's "mtd: nand: allow
vendor specific detection/initialization" patchset, which is needed for the
large-block MLC chip to be recognized correctly.
( http://lists.infradead.org/pipermail/linux-mtd/2016-June/068198.html

 )

Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

Add a dts file for tablets using the generic inet-q972 PCB.

Tablets with this PCB feature a mini-hdmi output, micro-usb usb-host,
micro-usb usb-otg, 3.5mm headphone jack, a micro sd slot,
(mini) power-barrel and an usb wifi module.

This has been tested on a 9.7" 1024x768 qware qw tb9718-qhd tablet.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

Just like with a13/a23/a33 most a31 tablets are derived from the same
reference design. Add a .dtsi file with all the common bits to avoid
endless copy and pasting of these.

The sun6i-reference-design-tablet.dtsi this commit adds is a copy
of sun6i-a31s-colorfly-e708-q1.dts with a few tablet specific bits
removed / left in sun6i-a31s-colorfly-e708-q1.dts.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

The presence of the mma8452_int_e708_q1 node is a copy and paste
error, remove it.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

The 32.768 kHz clock inside the A80 SoC is fed from an external source,
typically the AC100 RTC module.

Make the osc32k placeholder a fixed-factor clock so board dts files can
specify its source.

Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

Almost all sun8i tablets use a gsl1680 touchscreen controller, so add
a node describing it to reference-design-tablet.dtsi.

Almost all, but not all, so mark it as disabled by default (dts files
will also need to supply a firmware-name and resolution info).

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

The ga10h tablet has a rtl8703as wifi chip, add a dt node describing it.

This enables usage of wifi on this tablet (together with the out of
tree rtl8732bs driver).

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

This results in quite a nice cleanup for this dts file.

As an added bonus this also enables full otg support. I've tested that
this works as advertised.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

The Orange Pi Lite SBC is a small H3 based SBC, with 512MB RAM,
micro-sd slot, HDMI out, 2 USB-A connectors, 1 micro-USB connector,
sdio attached rtl8189ftv wifi and an ir receiver.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

A33-OLinuXino is A33 development board designed by Olimex LTD.

It has AXP223 PMU, 1GB DRAM, a micro SD card, one USB-OTG connector,
headphone and mic jacks, connector for LiPo battery and optional
4GB NAND Flash.

It has two 40-pin headers. One for LCD panel, and one for
additional modules. Also there is CSI/DSI connector.

Signed-off-by: Stefan Mavrodiev <stefan.mavrodiev@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

The CHIP has a status LED connected to one of the AXP GPIOs. Add the
gpio-leds node to be able to use the proper LED framework to control it.

Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

Add the AXP209 GPIO node to our AXP209 DTSI so that boards can use it.

Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>

This will allow u-boot to fill in a mac-address for Orange Pi 2
variants which use an sdio wifi without an eeprom for the mac.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

There is a new Orange Pi PC *Plus* version available now,
this is an extended version of the regular Orange Pi PC
with sdio wifi and an eMMC.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
[Maxime: Fix model and compatible]
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

Now that we've all the necessary bits in place we can enable
full otg support on these tablets.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

Signed-off-by: Rich Felker <dalias@libc.org>

This defconfig is intended not to be specific to a particular board;
it enables drivers for all currently-supported hardware, and should be
updated to include additional drivers as they are added.

Signed-off-by: Rich Felker <dalias@libc.org>

Enable common clk framework for DT-based boards and disable code that
depends on the legacy sh clk framework when common clk is enabled.
Once legacy drivers are converted over, the old code can be removed
entirely.

Signed-off-by: Rich Felker <dalias@libc.org>

Signed-off-by: Yoshinori Sato <ysato@users.sourceforge.jp>
Signed-off-by: Rich Felker <dalias@libc.org>

The mempool_destroy() function tests whether its argument is NULL
and then returns immediately. Thus the test around the calls is not needed.

This issue was detected by using the Coccinelle software.

Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Rich Felker <dalias@libc.org>

Signed-off-by: Rich Felker <dalias@libc.org>

Support is hooked up via a cpu start method specified in the device
tree, and also depends on DT nodes that describe the interfaces for
performing IPI and identifying which cpu execution is taking place on.
The currently used method is a form of spin table, where secondary
cpus are unblocked by writing to a special address.

Signed-off-by: Rich Felker <dalias@libc.org>

The SH2 version of entry.S uses global variables, which need to be
cpu-local in order to work with SMP. For ease of access from asm,
simply use arrays indexed by cpu number, and require the availability
of an address (mmio register or properly setup per-cpu memory) from
which the current cpu's index can be read.

Signed-off-by: Rich Felker <dalias@libc.org>

The version of futex.h in asm-generic should really be adapted to do
the same thing so that this hideous code does not have to be
duplicated per-arch.

Signed-off-by: Rich Felker <dalias@libc.org>

Signed-off-by: Rich Felker <dalias@libc.org>

The J-Core cpu has, as an ISA extension, an atomic compare-and-swap
instruction cas.l which applications need to use (instead the imask or
gusa atomic models, which are fundamentally limited to UP) for
synchronization in order to be compatible with SMP systems. Provide a
hwcap flag so that it's possible to do runtime selection and support
both.

Signed-off-by: Rich Felker <dalias@libc.org>

At the CPU/ISA level, the J2 is compatible with SH-2, and thus the
changes to add J2 support build on existing SH-2 support. However, J2
does not duplicate the memory-mapped SH-2 features like the cache
interface. Instead, the cache interfaces is described in the device
tree, and new code is added to be able to access the flat device tree
at early boot before it is unflattened.

Support is also added for receiving interrupts on trap numbers in the
range 16 to 31, since the J-Core aic1 interrupt controller generates
these traps. This range was unused but nominally for hardware
exceptions on SH-2, and a few values in this range were used for
exceptions on SH-2A, but SH-2A has its own version of the relevant
code.

No individual cpu subtypes are added for J2 since the intent moving
forward is to represent SoCs with device tree rather than as
hard-coded subtypes in the kernel. The CPU_SUBTYPE_J2 Kconfig item
exists only to fit into the existing cpu selection mechanism until it
is overhauled.

Signed-off-by: Rich Felker <dalias@libc.org>

We should set the error code here rather than incorrectly returning 0.
Otherwise static checkers complain.

Link: http://lkml.kernel.org/r/20160804053525.GM775@mwanda


Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Alexandre Bounine <alexandre.bounine@idt.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

The LNKGET based atomic sequence in __cmpxchg_u32 has slightly incorrect
constraints for the return value which under certain circumstances can
allow an address unit register to be used as the first operand of a CMP
instruction. This isn't a valid instruction however as the encodings
only allow a data unit to be specified. This would result in an
assembler error like the following:

  Error: failed to assemble instruction: "CMP A0.2,D0Ar6"

Fix by changing the constraint from "=&da" (assigned, early clobbered,
data or address unit register) to "=&d" (data unit register only).

The constraint for the second operand, "bd" (an op2 register where op1
is a data unit register and the instruction supports O2R) is already
correct assuming the first operand is a data unit register.

Other cases of CMP in inline asm have had their constraints checked, and
appear to all be fine.

Fixes: 6006c0d8

 ("metag: Atomics, locks and bitops")
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: linux-metag@vger.kernel.org
Cc: <stable@vger.kernel.org> # 3.9.x-

The jump table can reference text found in an __exit section.  Thus,
instead of discarding it at build time, include EXIT_TEXT as part of
__init and it will be released when the system boots.

Link: http://lkml.kernel.org/r/60284113bb759121e8ae3e99af1535647e52123f.1467837322.git.jbaron@akamai.com


Signed-off-by: Jason Baron <jbaron@akamai.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Chris Metcalf <cmetcalf@mellanox.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Joe Perches <joe@perches.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Previously, all the __exit sections were just dropped by the link phase.
However, if there are static_key (jump label) constructs in __exit
sections that are not modules, the link fails with the message:

   `.exit.text' referenced in section `__jump_table' of xxx.o:
   defined in discarded section `.exit.text' of xxx.o

Support this usage by keeping the .exit.text sections in the final image
if JUMP_LABEL is defined, then discarding them once initialization is
complete.

Link: http://lkml.kernel.org/r/bfd7c107c610c30e992868ebfe2a5d796a097464.1467837322.git.jbaron@akamai.com


Signed-off-by: Jason Baron <jbaron@akamai.com>
Signed-off-by: Chris Metcalf <cmetcalf@mellanox.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Joe Perches <joe@perches.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

The jump table can reference text found in an __exit section.  Thus,
instead of discarding it at build/link time, include EXIT_TEXT as part
of __init and release it at system boot time.

Without this patch the link fails with:

    `.exit.text' referenced in section `__jump_table' of xxx.o:
    defined in discarded section `.exit.text' of xxx.o

Link: http://lkml.kernel.org/r/d822da427ab07a02a394602eca687104ff682f83.1467837322.git.jbaron@akamai.com


Signed-off-by: Jason Baron <jbaron@akamai.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Chris Metcalf <cmetcalf@mellanox.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Joe Perches <joe@perches.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

The stringify_in_c() macro may not be included. Make the dependency
explicit.

Link: http://lkml.kernel.org/r/564720c5328edd53c9d56db325be7215440eec3e.1467837322.git.jbaron@akamai.com


Signed-off-by: Jason Baron <jbaron@akamai.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Joe Perches <joe@perches.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Chris Metcalf <cmetcalf@mellanox.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Joe Perches <joe@perches.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

The dma-mapping core and the implementations do not change the DMA
attributes passed by pointer.  Thus the pointer can point to const data.
However the attributes do not have to be a bitfield.  Instead unsigned
long will do fine:

1. This is just simpler.  Both in terms of reading the code and setting
   attributes.  Instead of initializing local attributes on the stack
   and passing pointer to it to dma_set_attr(), just set the bits.

2. It brings safeness and checking for const correctness because the
   attributes are passed by value.

Semantic patches for this change (at least most of them):

    virtual patch
    virtual context

    @r@
    identifier f, attrs;

    @@
    f(...,
    - struct dma_attrs *attrs
    + unsigned long attrs
    , ...)
    {
    ...
    }

    @@
    identifier r.f;
    @@
    f(...,
    - NULL
    + 0
     )

and

    // Options: --all-includes
    virtual patch
    virtual context

    @r@
    identifier f, attrs;
    type t;

    @@
    t f(..., struct dma_attrs *attrs);

    @@
    identifier r.f;
    @@
    f(...,
    - NULL
    + 0
     )

Link: http://lkml.kernel.org/r/1468399300-5399-2-git-send-email-k.kozlowski@samsung.com


Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Acked-by: Vineet Gupta <vgupta@synopsys.com>
Acked-by: Robin Murphy <robin.murphy@arm.com>
Acked-by: Hans-Christian Noren Egtvedt <egtvedt@samfundet.no>
Acked-by: Mark Salter <msalter@redhat.com> [c6x]
Acked-by: Jesper Nilsson <jesper.nilsson@axis.com> [cris]
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch> [drm]
Reviewed-by: Bart Van Assche <bart.vanassche@sandisk.com>
Acked-by: Joerg Roedel <jroedel@suse.de> [iommu]
Acked-by: Fabien Dessenne <fabien.dessenne@st.com> [bdisp]
Reviewed-by: Marek Szyprowski <m.szyprowski@samsung.com> [vb2-core]
Acked-by: David Vrabel <david.vrabel@citrix.com> [xen]
Acked-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com> [xen swiotlb]
Acked-by: Joerg Roedel <jroedel@suse.de> [iommu]
Acked-by: Richard Kuo <rkuo@codeaurora.org> [hexagon]
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org> [m68k]
Acked-by: Gerald Schaefer <gerald.schaefer@de.ibm.com> [s390]
Acked-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Acked-by: Hans-Christian Noren Egtvedt <egtvedt@samfundet.no> [avr32]
Acked-by: Vineet Gupta <vgupta@synopsys.com> [arc]
Acked-by: Robin Murphy <robin.murphy@arm.com> [arm64 and dma-iommu]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>