The TBS A711 is a tablet with an A83T, a modem, wifi/BT chip, an eMMC and a
1024x600 LVDS display.

Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

sun4i-a10.dtsi was missing i2s0 block. Add it.

Signed-off-by: Priit Laes <plaes@plaes.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

Add the new DAI blocks to the device tree.

Signed-off-by: Marcus Cooper <codekipper@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

The A83T has an UART1 controller, with the RTS and CTS pins routed so it
can be used for devices with hardware flow control, like a bluetooth chip.

Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

Add the pinctrl definitions for the A83t MMC1 controller.

Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

Those nodes are useless, remove them.

Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

From revision J the board uses new phy chip LAN8710. Compared
with RTL8201, RA17 pin is TXERR. It has pullup which causes phy
not to work. To fix this PA17 is muxed with GMAC function. This
makes the pin output-low.

This patch is compatible with earlier board revisions, since this
pin wasn't connected to phy.

Signed-off-by: Stefan Mavrodiev <stefan@olimex.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

The BT side of the AP6212 WiFi/BT combo module is connected to
uart3.

Enable BT on this board by enabling uart3 with using additionally
the cts and rts pins.

Signed-off-by: Philipp Rossak <embed3d@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

This node adds the definition for the UART3 RTS and CTS Pins

That makes it able to use UART3 with RTS and CTS.

Signed-off-by: Philipp Rossak <embed3d@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

The Nanopi M1 Plus has an onboard IR receiver.
This enables the onboard IR receiver subnode.

Signed-off-by: Philipp Rossak <embed3d@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

The Nanopi M1 has an onboard IR receiver.
This enables the onboard IR receiver subnode.

Signed-off-by: Philipp Rossak <embed3d@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

The axp209.dtsi defines nodes for ac, usb and battery supplies for a
while now. This patch enables these nodes for the A20-Olinuxino-Micro,
which has connectors for all three of them.

The patch was run-tested against linux-next-20170825.

Signed-off-by: Harald Geyer <harald@ccbib.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

A20-OLinuXino-MICRO has option with onboard eMMC chip. For
now it's only shipped with 4BG chip, but in the future this
may change.

Signed-off-by: Stefan Mavrodiev <stefan@olimex.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

Convert sun4i-a10.dtsi to new CCU driver.

Tested on Gemei G9 tablet.

Signed-off-by: Priit Laes <plaes@plaes.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

Convert sun7i-a20.dtsi to new CCU driver.

Tested on Cubietruck.

Signed-off-by: Priit Laes <plaes@plaes.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

When the second display pipeline device nodes for the A31/A31s were
added, it was not known that the TCONs could (through either DRCs)
select either backend as their input. Thus in the endpoints connecting
these components together, the endpoint IDs were set to 0, while in
fact they should have been set to 1.

Cc: <stable@vger.kernel.org>
Fixes: 9a26882a ("ARM: dts: sun6i: Add second display pipeline device
		      nodes")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

Since current tree support AXP803 regulators, replace
fixed regulator with AXP803 dcdc1 regulator.

Tested on pine64.

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

When emulating a nested VM-entry from L1 to L2, several control field
validation checks are deferred to the hardware. Should one of these
validation checks fail, vcpu_vmx_run will set the vmx->fail flag. When
this happens, the L2 guest state is not loaded (even in part), and
execution should continue in L1 with the next instruction after the
VMLAUNCH/VMRESUME.

The VMCS12 is not modified (except for the VM-instruction error
field), the VMCS12 MSR save/load lists are not processed, and the CPU
state is not loaded from the VMCS12 host area. Moreover, the vmcs02
exit reason is stale, so it should not be consulted for any reason.

Signed-off-by: Jim Mattson <jmattson@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>

On an early VMLAUNCH/VMRESUME failure (i.e. one which sets the
VM-instruction error field of the current VMCS), the launch state of
the current VMCS is not set to "launched," and the VM-exit information
fields of the current VMCS (including IDT-vectoring information and
exit reason) are stale.

On a late VMLAUNCH/VMRESUME failure (i.e. one which sets the high bit
of the exit reason field), the launch state of the current VMCS is not
set to "launched," and only two of the VM-exit information fields of
the current VMCS are modified (exit reason and exit
qualification). The remaining VM-exit information fields of the
current VMCS (including IDT-vectoring information, in particular) are
stale.

Signed-off-by: Jim Mattson <jmattson@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>

After a successful VM-entry, RFLAGS is cleared, with the exception of
bit 1, which is always set. This is handled by load_vmcs12_host_state.

Signed-off-by: Jim Mattson <jmattson@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>

For example, the following could occur, making us miss a wakeup:

CPU0					CPU1
kvm_vcpu_block				kvm_mips_comparecount_func
					  [L] swait_active(&vcpu->wq)
  [S] prepare_to_swait(&vcpu->wq)
  [L] if (!kvm_vcpu_has_pending_timer(vcpu))
         schedule()                       [S] queue_timer_int(vcpu)

Ensure that the swait_active() check is not hoisted over the interrupt.

Signed-off-by: Davidlohr Bueso <dbueso@suse.de>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>

Particularly because kvmppc_fast_vcpu_kick_hv() is a callback,
ensure that we properly serialize wq active checks in order to
avoid potentially missing a wakeup due to racing with the waiter
side.

Signed-off-by: Davidlohr Bueso <dbueso@suse.de>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>

During code inspection, the following potential race was seen:

CPU0   	    		    	     	CPU1
kvm_async_pf_task_wait			apf_task_wake_one
					  [L] swait_active(&n->wq)
  [S] prepare_to_swait(&n.wq)
  [L] if (!hlist_unhahed(&n.link))
	schedule()			  [S] hlist_del_init(&n->link);

Properly serialize swait_active() checks such that a wakeup is
not missed.

Signed-off-by: Davidlohr Bueso <dbueso@suse.de>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>

A comment might serve future readers.

Signed-off-by: Davidlohr Bueso <dbueso@suse.de>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>

The value of the guest_irq argument to vmx_update_pi_irte() is
ultimately coming from a KVM_IRQFD API call. Do not BUG() in
vmx_update_pi_irte() if the value is out-of bounds. (Especially,
since KVM as a whole seems to hang after that.)

Instead, print a message only once if we find that we don't have a
route for a certain IRQ (which can be out-of-bounds or within the
array).

This fixes CVE-2017-1000252.

Fixes: efc64404 ("KVM: x86: Update IRTE for posted-interrupts")
Signed-off-by: Jan H. Schönherr <jschoenh@amazon.de>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>

Mainline crashes as follows when running nios2 images.

On node 0 totalpages: 65536
free_area_init_node: node 0, pgdat c8408fa0, node_mem_map c8726000
  Normal zone: 512 pages used for memmap
  Normal zone: 0 pages reserved
  Normal zone: 65536 pages, LIFO batch:15
Unable to handle kernel NULL pointer dereference at virtual address 00000000
ea = c8003cb0, ra = c81cbf40, cause = 15
Kernel panic - not syncing: Oops

Problem is seen because get_cycles() is called before the timer it depends
on is initialized. Returning 0 in that situation fixes the problem.

Fixes: 33d72f38 ("init/main.c: extract early boot entropy from the ..")
Cc: Laura Abbott <labbott@redhat.com>
Cc: Kees Cook <keescook@chromium.org>
Cc: Daniel Micay <danielmicay@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>

Allow earlycon to be used on the JTAG UART present in the 3c120 GHRD.

Signed-off-by: Tobias Klauser <tklauser@distanz.ch>

If L1 does not specify the "use TPR shadow" VM-execution control in
vmcs12, then L0 must specify the "CR8-load exiting" and "CR8-store
exiting" VM-execution controls in vmcs02. Failure to do so will give
the L2 VM unrestricted read/write access to the hardware CR8.

This fixes CVE-2017-12154.

Signed-off-by: Jim Mattson <jmattson@google.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>

This fixes the emulation of the dcbz instruction in the alignment
interrupt handler.  The error was that we were comparing just the
instruction type field of op.type rather than the whole thing,
and therefore the comparison "type != CACHEOP + DCBZ" was always
true.

Fixes: 31bfdb03 ("powerpc: Use instruction emulation infrastructure to handle alignment faults")
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Tested-by: Michal Sojka <sojkam1@fel.cvut.cz>
Tested-by: Christian Zigotzky <chzigotzky@xenosoft.de>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

qemu-system-x86-8600  [004] d..1  7205.687530: kvm_entry: vcpu 2
qemu-system-x86-8600  [004] ....  7205.687532: kvm_exit: reason EXCEPTION_NMI rip 0xffffffffa921297d info ffffeb2c0e44e018 80000b0e
qemu-system-x86-8600  [004] ....  7205.687532: kvm_page_fault: address ffffeb2c0e44e018 error_code 0
qemu-system-x86-8600  [004] ....  7205.687620: kvm_try_async_get_page: gva = 0xffffeb2c0e44e018, gfn = 0x427e4e
qemu-system-x86-8600  [004] .N..  7205.687628: kvm_async_pf_not_present: token 0x8b002 gva 0xffffeb2c0e44e018
    kworker/4:2-7814  [004] ....  7205.687655: kvm_async_pf_completed: gva 0xffffeb2c0e44e018 address 0x7fcc30c4e000
qemu-system-x86-8600  [004] ....  7205.687703: kvm_async_pf_ready: token 0x8b002 gva 0xffffeb2c0e44e018
qemu-system-x86-8600  [004] d..1  7205.687711: kvm_entry: vcpu 2

After running some memory intensive workload in guest, I catch the kworker
which completes the GUP too quickly, and queues an "Page Ready" #PF exception
after the "Page not Present" exception before the next vmentry as the above
trace which will result in #DF injected to guest.

This patch fixes it by clearing the queue for "Page not Present" if "Page Ready"
occurs before the next vmentry since the GUP has already got the required page
and shadow page table has already been fixed by "Page Ready" handler.

Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Radim Krčmář <rkrcmar@redhat.com>
Signed-off-by: Wanpeng Li <wanpeng.li@hotmail.com>
Fixes: 7c90705b ("KVM: Inject asynchronous page fault into a PV guest if page is swapped out.")
[Changed indentation and added clearing of injected. - Radim]
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>

Don't block vCPU if there is pending exception.

Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Radim Krčmář <rkrcmar@redhat.com>
Signed-off-by: Wanpeng Li <wanpeng.li@hotmail.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>

SVM AVIC hardware accelerates guest write to APIC_EOI register
(for edge-trigger interrupt), which means it does not trap to KVM.

So, only enable SVM AVIC only in split irqchip mode.
(e.g. launching qemu w/ option '-machine kernel_irqchip=split').

Suggested-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Suravee Suthikulpanit <suravee.suthikulpanit@amd.com>
Fixes: 44a95dae ("KVM: x86: Detect and Initialize AVIC support")
[Removed pr_debug - Radim.]
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>

... and __initconst if applicable.

Based on similar work for an older kernel in the Grsecurity patch.

[JD: fix toshiba-wmi build]
[JD: add htcpen]
[JD: move __initconst where checkscript wants it]

Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jean Delvare <jdelvare@suse.de>

The stacktraces always begin as follows:

  [<c00117b4>] save_stack_trace_tsk+0x0/0x98
  [<c0011870>] save_stack_trace+0x24/0x28
  ...

This is because the stack trace code includes the stack frames for
itself.  This is incorrect behaviour, and also leads to "skip" doing the
wrong thing (which is the number of stack frames to avoid recording.)

Perversely, it does the right thing when passed a non-current thread.
Fix this by ensuring that we have a known constant number of frames
above the main stack trace function, and always skip these.

This was fixed for arch arm by commit 3683f44c ("ARM: stacktrace:
avoid listing stacktrace functions in stacktrace")

Link: http://lkml.kernel.org/r/1504078343-28754-1-git-send-email-guptap@codeaurora.org


Signed-off-by: Prakash Gupta <guptap@codeaurora.org>
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
Cc: Michal Hocko <mhocko@suse.com>
Cc: Vlastimil Babka <vbabka@suse.cz>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

GFP_TEMPORARY was introduced by commit e12ba74d ("Group short-lived
and reclaimable kernel allocations") along with __GFP_RECLAIMABLE.  It's
primary motivation was to allow users to tell that an allocation is
short lived and so the allocator can try to place such allocations close
together and prevent long term fragmentation.  As much as this sounds
like a reasonable semantic it becomes much less clear when to use the
highlevel GFP_TEMPORARY allocation flag.  How long is temporary? Can the
context holding that memory sleep? Can it take locks? It seems there is
no good answer for those questions.

The current implementation of GFP_TEMPORARY is basically GFP_KERNEL |
__GFP_RECLAIMABLE which in itself is tricky because basically none of
the existing caller provide a way to reclaim the allocated memory.  So
this is rather misleading and hard to evaluate for any benefits.

I have checked some random users and none of them has added the flag
with a specific justification.  I suspect most of them just copied from
other existing users and others just thought it might be a good idea to
use without any measuring.  This suggests that GFP_TEMPORARY just
motivates for cargo cult usage without any reasoning.

I believe that our gfp flags are quite complex already and especially
those with highlevel semantic should be clearly defined to prevent from
confusion and abuse.  Therefore I propose dropping GFP_TEMPORARY and
replace all existing users to simply use GFP_KERNEL.  Please note that
SLAB users with shrinkers will still get __GFP_RECLAIMABLE heuristic and
so they will be placed properly for memory fragmentation prevention.

I can see reasons we might want some gfp flag to reflect shorterm
allocations but I propose starting from a clear semantic definition and
only then add users with proper justification.

This was been brought up before LSF this year by Matthew [1] and it
turned out that GFP_TEMPORARY really doesn't have a clear semantic.  It
seems to be a heuristic without any measured advantage for most (if not
all) its current users.  The follow up discussion has revealed that
opinions on what might be temporary allocation differ a lot between
developers.  So rather than trying to tweak existing users into a
semantic which they haven't expected I propose to simply remove the flag
and start from scratch if we really need a semantic for short term
allocations.

[1] http://lkml.kernel.org/r/20170118054945.GD18349@bombadil.infradead.org

[akpm@linux-foundation.org: fix typo]
[akpm@linux-foundation.org: coding-style fixes]
[sfr@canb.auug.org.au: drm/i915: fix up]
  Link: http://lkml.kernel.org/r/20170816144703.378d4f4d@canb.auug.org.au
Link: http://lkml.kernel.org/r/20170728091904.14627-1-mhocko@kernel.org


Signed-off-by: Michal Hocko <mhocko@suse.com>
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Acked-by: Mel Gorman <mgorman@suse.de>
Acked-by: Vlastimil Babka <vbabka@suse.cz>
Cc: Matthew Wilcox <willy@infradead.org>
Cc: Neil Brown <neilb@suse.de>
Cc: "Theodore Ts'o" <tytso@mit.edu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

The intention is to return negative error codes.  "pid" is already
negative but we accidentally negate it again back to positive.

Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Richard Weinberger <richard@nod.at>

Static checkers would urge us to add curly braces to this code, but
actually the code works correctly.  It just isn't indented right.

Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Richard Weinberger <richard@nod.at>

When building a dynamic kernel image use relative symbols with MODVERSIONS.

Signed-off-by: Thomas Meyer <thomas@m3y3r.de>
Signed-off-by: Richard Weinberger <richard@nod.at>

Debian's gcc defaults to pie. The global Makefile already defines the -fno-pie option.
Link UML dynamic kernel image also with -no-pie to fix the build.

Signed-off-by: Thomas Meyer <thomas@m3y3r.de>
Signed-off-by: Richard Weinberger <richard@nod.at>

Explicitly export symbols so modpost doesn't complain.

Signed-off-by: Thomas Meyer <thomas@m3y3r.de>
Signed-off-by: Richard Weinberger <richard@nod.at>