This allows nonexclusive (simultaneous) access to a single
GPIO line for the fixed regulator enable line. This happens
when several regulators use the same GPIO for enabling and
disabling a regulator, and all need a handle on their GPIO
descriptor.

This solution with a special flag is not entirely elegant
and should ideally be replaced by something more careful as
this makes it possible for several consumers to
enable/disable the same GPIO line to the left and right
without any consistency. The current use inside the regulator
core should however be fine as it takes special care to
handle this.

For the state of the GPIO backend, this is still the
lesser evil compared to going back to global GPIO
numbers.

Cc: Marek Szyprowski <m.szyprowski@samsung.com>
Cc: Jon Hunter <jonathanh@nvidia.com>
Fixes: efdfeb07

 ("regulator: fixed: Convert to use GPIO descriptor only")
Reported-by: Marek Szyprowski <m.szyprowski@samsung.com>
Tested-by: Jon Hunter <jonathanh@nvidia.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>

Lochnagar is an evaluation and development board for Cirrus
Logic Smart CODEC and Amp devices. It allows the connection of
most Cirrus Logic devices on mini-cards, as well as allowing
connection of various application processor systems to provide a
full evaluation platform. This driver supports the board
controller chip on the Lochnagar board.

The Lochnagar board provides power supplies for the attached
CODEC/Amp device. Currently this driver supports the microphone
supplies and the digital core voltage for the attached
device. There are some additional supplies that will be
added in time but these supplies are sufficient for most
systems/use-cases.

Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

-EINVAL is not a valid return value for .of_map_mode, return
REGULATOR_MODE_INVALID instead.

Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

The stpmic1 PMIC embeds several regulators and switches with
different capabilities.

Signed-off-by: pascal paillet <p.paillet@st.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

The STPMIC1 regulators supply power to the application processor as well as
to the external system peripherals such as DDR, Flash memories and system
devices.

Signed-off-by: pascal paillet <p.paillet@st.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.

Notice that in this particular case, I moved the whole comment
"Fall through to the check below.", which contains the "Fall through"
comment, at the bottom of the case, which is what GCC is expecting
to find.

Addresses-Coverity-ID: 1436594 ("Missing break in switch")
Addresses-Coverity-ID: 1364475 ("Missing break in switch")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

commit efdfeb07
("regulator: fixed: Convert to use GPIO descriptor only")
switched to use gpiod_get() to look up the regulator from the
gpiolib core whether that is device tree or boardfile.

This meant that we activate the code in
a603a2b8 ("gpio: of: Add special quirk to parse regulator flags")
which means the descriptors coming from the device tree already
have the right inversion and open drain semantics set up from
the gpiolib core.

As the fixed regulator was inspected again we got the
inverted inversion and things broke.

Fix it by ignoring the config in the device tree for now: the
later patches in the series will push all inversion handling
over to the gpiolib core and set it up properly in the
boardfiles for legacy devices, but I did not finish that
for this kernel cycle.

Fixes: commit efdfeb07

 ("regulator: fixed: Convert to use GPIO descriptor only")
Reported-by: Leonard Crestez <leonard.crestez@nxp.com>
Reported-by: Fabio Estevam <festevam@gmail.com>
Reported-by: John Stultz <john.stultz@linaro.org>
Reported-by: Anders Roxell <anders.roxell@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Tested-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>

regulator/mfd: Support for the ROHM BD71847

This adds support for the BD71847 which touches both MFD and regulator.
There's a few other bits and pieces included as some dependency patches
had already been applied so would've required rebasing.

rename bd71837-regulator.c to bd718x7-regulator.c to reflect the
fact that also BD71847 is now supported by the driver.

Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

Few regulators in BD71837 and BD71847 can output voltages from
different voltage ranges. Register interface is arranged so that
used range is selected by toggling bits which are not next to actual
voltage selection bits. Then the voltage inside selected range is
determined by voltage selection bits (as usual). Support BD71837
and BD71847 selectible range voltages using new pickable ranges
helpers.

Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

Rename parts of code that support both BD71837 and BD71847 to BD718XX.

Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>

For example ROHM BD71837 and ROHM BD71847 Power management ICs have
regulators which provide multiple linear ranges. Ranges can be
selected by individual non contagious bit in vsel register. Add
regmap helper functions for selecting ranges.

Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

Add ROHM BD71847 Power Management IC MFD binding information to
device-tree binding documents.

Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>

Add ROHM BD71847 Power Management IC regulator binding information to
device-tree binding documents.

Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>

BD71847 is reduced version of BD71837. DVS bucks 3 and 4 are
removed as is LDO7. Voltage ranges of some regulators are
expanded.

Add initial support for BD71847 with BD71837 driver.

Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>

regulator: Fixes for 4.19

A collection of fairly minor bug fixes here, a couple of driver specific
ones plus two core fixes.  There's one fix for the new suspend state
code which fixes some confusion with constant values that are supposed
to indicate noop operation and another fixing a race condition with the
creation of sysfs files on new regulators.

Clang warns that the address of a pointer will always evaluated as true
in a boolean context:

drivers/regulator/da9052-regulator.c:423:22: warning: address of array
'pdata->regulators' will always evaluate to 'true'
[-Wpointer-bool-conversion]
        if (pdata && pdata->regulators) {
                  ~~ ~~~~~~~^~~~~~~~~~
drivers/regulator/da9055-regulator.c:615:22: warning: address of array
'pdata->regulators' will always evaluate to 'true'
[-Wpointer-bool-conversion]
        if (pdata && pdata->regulators) {
                  ~~ ~~~~~~~^~~~~~~~~~

Link: https://github.com/ClangBuiltLinux/linux/issues/142


Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

The PMS405 provdies 5 SMPS regulators and 13 LDOs, add these to the RPM
regulator driver.

Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>

dev_set_drvdata() needs to be called before device_register()
exposes device to userspace. Otherwise kernel crashes after it
gets null pointer from dev_get_drvdata() when userspace tries
to access sysfs entries.

[Removed backtrace for length -- broonie]

Signed-off-by: Yu Zhao <yuzhao@google.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org

0-Day tests found compilation error on x86. Driver won't
compile on x86_64 as "of_match_ptr" is not found. Add missing
include <linux/of.h>

Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

As we augmented the regulator core to accept a GPIO descriptor instead
of a GPIO number, we can augment the fixed GPIO regulator to look up
and pass that descriptor directly from device tree or board GPIO
descriptor look up tables.

Some boards just auto-enumerate their fixed regulator platform devices
and I have assumed they get names like "fixed-regulator.0" but it's
pretty hard to guess this. I need some testing from board maintainers to
be sure. Other boards are straight forward, using just plain
"fixed-regulator" (ID -1) or "fixed-regulator.1" hammering down the
device ID.

It seems the da9055 and da9211 has never got around to actually passing
any enable gpio into its platform data (not the in-tree code anyway) so we
can just decide to simply pass a descriptor instead.

The fixed GPIO-controlled regulator in mach-pxa/ezx.c was confusingly named
"*_dummy_supply_device" while it is a very real device backed by a GPIO
line. There is nothing dummy about it at all, so I renamed it with the
infix *_regulator_* as part of this patch set.

Intel MID portions tested by Andy.

Tested-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> # Check the x86 BCM stuff
Acked-by: Tony Lindgren <tony@atomide.com> # OMAP1,2,3 maintainer
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Janusz Krzysztofik <jmkrzyszt@gmail.com>
Reviewed-by: Mike Rapoport <rppt@linux.vnet.ibm.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

Fix kernel-doc warning:

../drivers/regulator/core.c:4479: warning: Excess function parameter 'state' description in 'regulator_suspend'

Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Liam Girdwood <lgirdwood@gmail.com>
Cc: Mark Brown <broonie@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>

regulator_pm_ops with regulator_suspend and regulator_resume functions are
assigned to every regulator device registered in the system, so there is no
need to iterate over all again in them. Replace class_for_each_device()
construction with direct operation on the rdev embedded in the given
regulator device. This saves a lots of useless operations in suspend and
resume paths.

Fixes: f7efad10

: regulator: add PM suspend and resume hooks
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

Some regulators don't have all states defined and in such cases regulator
core should not assume anything. However in current implementation
of of_get_regulation_constraints() DO_NOTHING_IN_SUSPEND enable value was
set only for regulators which had suspend node defined, otherwise the
default 0 value was used, what means DISABLE_IN_SUSPEND. This lead to
broken system suspend/resume on boards, which had simple regulator
constraints definition (without suspend state nodes).

To avoid further mismatches between the default and uninitialized values
of the suspend enabled/disabled states, change the values of the them,
so default '0' means DO_NOTHING_IN_SUSPEND.

Fixes: 72069f99

: regulator: leave one item to record whether regulator is enabled
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org

Commit 1c892e38 ("regulator: da9063: Handle less LDOs on DA9063L")
reordered the da9063_regulator_info[] array, but not the DA9063_ID_*
regulator ids and not the da9063_matches[] array, because ids are used
as indices in the array initializer. This mismatch between regulator id
and da9063_regulator_info[] array index causes the driver probe to fail
because constraints from DT are not applied to the correct regulator:

  da9063 0-0058: Device detected (chip-ID: 0x61, var-ID: 0x50)
  DA9063_BMEM: Bringing 900000uV into 3300000-3300000uV
  DA9063_LDO9: Bringing 3300000uV into 2500000-2500000uV
  DA9063_LDO1: Bringing 900000uV into 3300000-3300000uV
  DA9063_LDO1: failed to apply 3300000-3300000uV constraint(-22)

This patch reorders the DA9063_ID_* as apparently intended, and with
them the entries in the da90630_matches[] array.

Fixes: 1c892e38

 ("regulator: da9063: Handle less LDOs on DA9063L")
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

There is a HW quirk in BD71837. The shutdown sequence timings for
bucks/LDOs which are enabled via register interface are changed.
At PMIC poweroff the voltage for BUCK6/7 is cut immediately at the
beginning of shut-down sequence. This causes LDO5/6 voltage
monitoring to detect under voltage and force PMIC to emergency
state instead of poweroff. Disable voltage monitoring for LDO5 and
LDO6 at probe to avoid this.

Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org

No functional change here but it can make the code more readable to
have breaks in the "default" case even though it's the last case.
Let's add them.

Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: David Collins <collinsd@codeaurora.org>
Signed-off-by: Mark Brown <broonie@kernel.org>

Most functions that access the rdev lock the rdev mutex before looking
at data.  ...but not the code that implements the debugfs
regulator_summary.  It probably should though, so let's do it.

Note: this fixes no known issues.  The problem was found only by code
inspection.

Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Mark Brown <broonie@kernel.org>

It's handy to see the load requested by a regulator consumer in the
regulator_summary.  Add it.

Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Mark Brown <broonie@kernel.org>

It's handy to know what opmode a regulator has been configured to in
the summary.  Add it.

Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Mark Brown <broonie@kernel.org>

Don't give up voltage mapping if first range with suitable min/max uV
does not provide the wanted voltage.

Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

Set it once is enough.
Also move n_voltages close to volt_table for better readability.

Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

Add missing .owner field in regulator_desc, which is used for refcounting.

Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

In preparation to remove the node name pointer from struct device_node,
convert printf users to use the %pOFn format specifier.

Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>

Pull timer update from Thomas Gleixner:
 "New defines for the compat time* types so they can be shared between
  32bit and 64bit builds. Not used yet, but merging them now allows the
  actual conversions to be merged through different maintainer trees
  without dependencies

  We still have compat interfaces for 32bit on 64bit even with the new
  2038 safe timespec/val variants because pointer size is different. And
  for the old style timespec/val interfaces we need yet another 'compat'
  interface for both 32bit native and 32bit on 64bit"

* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  y2038: Provide aliases for compat helpers

Pull IDA updates from Matthew Wilcox:
 "A better IDA API:

      id = ida_alloc(ida, GFP_xxx);
      ida_free(ida, id);

  rather than the cumbersome ida_simple_get(), ida_simple_remove().

  The new IDA API is similar to ida_simple_get() but better named.  The
  internal restructuring of the IDA code removes the bitmap
  preallocation nonsense.

  I hope the net -200 lines of code is convincing"

* 'ida-4.19' of git://git.infradead.org/users/willy/linux-dax: (29 commits)
  ida: Change ida_get_new_above to return the id
  ida: Remove old API
  test_ida: check_ida_destroy and check_ida_alloc
  test_ida: Convert check_ida_conv to new API
  test_ida: Move ida_check_max
  test_ida: Move ida_check_leaf
  idr-test: Convert ida_check_nomem to new API
  ida: Start new test_ida module
  target/iscsi: Allocate session IDs from an IDA
  iscsi target: fix session creation failure handling
  drm/vmwgfx: Convert to new IDA API
  dmaengine: Convert to new IDA API
  ppc: Convert vas ID allocation to new IDA API
  media: Convert entity ID allocation to new IDA API
  ppc: Convert mmu context allocation to new IDA API
  Convert net_namespace to new IDA API
  cb710: Convert to new IDA API
  rsxx: Convert to new IDA API
  osd: Convert to new IDA API
  sd: Convert to new IDA API
  ...

Pull gcc plugin fix from Kees Cook:
 "Lift gcc test into Kconfig. This is for better behavior when the
  kernel is built with Clang, reported by Stefan Agner"

* tag 'gcc-plugins-v4.19-rc1-fix' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux:
  gcc-plugins: Disable when building under Clang

Pull perf updates from Thomas Gleixner:
 "Kernel:
   - Improve kallsyms coverage
   - Add x86 entry trampolines to kcore
   - Fix ARM SPE handling
   - Correct PPC event post processing

  Tools:
   - Make the build system more robust
   - Small fixes and enhancements all over the place
   - Update kernel ABI header copies
   - Preparatory work for converting libtraceevnt to a shared library
   - License cleanups"

* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (100 commits)
  tools arch: Update arch/x86/lib/memcpy_64.S copy used in 'perf bench mem memcpy'
  tools arch x86: Update tools's copy of cpufeatures.h
  perf python: Fix pyrf_evlist__read_on_cpu() interface
  perf mmap: Store real cpu number in 'struct perf_mmap'
  perf tools: Remove ext from struct kmod_path
  perf tools: Add gzip_is_compressed function
  perf tools: Add lzma_is_compressed function
  perf tools: Add is_compressed callback to compressions array
  perf tools: Move the temp file processing into decompress_kmodule
  perf tools: Use compression id in decompress_kmodule()
  perf tools: Store compression id into struct dso
  perf tools: Add compression id into 'struct kmod_path'
  perf tools: Make is_supported_compression() static
  perf tools: Make decompress_to_file() function static
  perf tools: Get rid of dso__needs_decompress() call in __open_dso()
  perf tools: Get rid of dso__needs_decompress() call in symbol__disassemble()
  perf tools: Get rid of dso__needs_decompress() call in read_object_code()
  tools lib traceevent: Change to SPDX License format
  perf llvm: Allow passing options to llc in addition to clang
  perf parser: Improve error message for PMU address filters
  ...

Pull x86 fixes from Thomas Gleixner:

 - Correct the L1TF fallout on 32bit and the off by one in the 'too much
   RAM for protection' calculation.

 - Add a helpful kernel message for the 'too much RAM' case

 - Unbreak the VDSO in case that the compiler desides to use indirect
   jumps/calls and emits retpolines which cannot be resolved because the
   kernel uses its own thunks, which does not work for the VDSO. Make it
   use the builtin thunks.

 - Re-export start_thread() which was unexported when the 32/64bit
   implementation was unified. start_thread() is required by modular
   binfmt handlers.

 - Trivial cleanups

* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/speculation/l1tf: Suggest what to do on systems with too much RAM
  x86/speculation/l1tf: Fix off-by-one error when warning that system has too much RAM
  x86/kvm/vmx: Remove duplicate l1d flush definitions
  x86/speculation/l1tf: Fix overflow in l1tf_pfn_limit() on 32bit
  x86/process: Re-export start_thread()
  x86/mce: Add notifier_block forward declaration
  x86/vdso: Fix vDSO build if a retpoline is emitted