- Feb 14, 2019
-
-
Eric Dumazet authored
With many active TCP sockets, fat TCP sockets could fool __sk_mem_raise_allocated() thanks to an overflow. They would increase their share of the memory, instead of decreasing it. Signed-off-by:
Eric Dumazet <edumazet@google.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
John David Anglin authored
The GPIO interrupt controller on the espressobin board only supports edge interrupts. If one enables the use of hardware interrupts in the device tree for the 88E6341, it is possible to miss an edge. When this happens, the INTn pin on the Marvell switch is stuck low and no further interrupts occur. I found after adding debug statements to mv88e6xxx_g1_irq_thread_work() that there is a race in handling device interrupts (e.g. PHY link interrupts). Some interrupts are directly cleared by reading the Global 1 status register. However, the device interrupt flag, for example, is not cleared until all the unmasked SERDES and PHY ports are serviced. This is done by reading the relevant SERDES and PHY status register. The code only services interrupts whose status bit is set at the time of reading its status register. If an interrupt event occurs after its status is read and before all interrupts are serviced, then this event will not be serviced and the INTn output pin will remain low. This is not a problem with polling or level interrupts since the handler will be called again to process the event. However, it's a big problem when using level interrupts. The fix presented here is to add a loop around the code servicing switch interrupts. If any pending interrupts remain after the current set has been handled, we loop and process the new set. If there are no pending interrupts after servicing, we are sure that INTn has gone high and we will get an edge when a new event occurs. Tested on espressobin board. Fixes: dc30c35b ("net: dsa: mv88e6xxx: Implement interrupt support.") Signed-off-by:
John David Anglin <dave.anglin@bell.net> Tested-by:
Andrew Lunn <andrew@lunn.ch> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Heiner Kallweit authored
phylib enables interrupts before phy_start() has been called, and if we receive an interrupt in a non-started state, the interrupt handler returns IRQ_NONE. This causes problems with at least one Marvell chip as reported by Andrew. Fix this by handling interrupts the same as in phy_mac_interrupt(), basically always running the phylib state machine. It knows when it has to do something and when not. This change allows to handle interrupts gracefully even if they occur in a non-started state. Fixes: 2b3e88ea ("net: phy: improve phy state checking") Reported-by:
Andrew Lunn <andrew@lunn.ch> Signed-off-by:
Heiner Kallweit <hkallweit1@gmail.com> Reviewed-by:
Andrew Lunn <andrew@lunn.ch> Reviewed-by:
Florian Fainelli <f.fainelli@gmail.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Xin Long authored
In sctp_stream_init(), after sctp_stream_outq_migrate() freed the surplus streams' ext, but sctp_stream_alloc_out() returns -ENOMEM, stream->outcnt will not be set to 'outcnt'. With the bigger value on stream->outcnt, when closing the assoc and freeing its streams, the ext of those surplus streams will be freed again since those stream exts were not set to NULL after freeing in sctp_stream_outq_migrate(). Then the invalid-free issue reported by syzbot would be triggered. We fix it by simply setting them to NULL after freeing. Fixes: 5bbbbe32 ("sctp: introduce stream scheduler foundations") Reported-by:
<syzbot+58e480e7b28f2d890bfd@syzkaller.appspotmail.com> Signed-off-by:
Xin Long <lucien.xin@gmail.com> Acked-by:
Neil Horman <nhorman@tuxdriver.com> Acked-by:
Marcelo Ricardo Leitner <marcelo.leitner@gmail.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Xin Long authored
Jianlin reported a panic when running sctp gso over gre over vlan device: [ 84.772930] RIP: 0010:do_csum+0x6d/0x170 [ 84.790605] Call Trace: [ 84.791054] csum_partial+0xd/0x20 [ 84.791657] gre_gso_segment+0x2c3/0x390 [ 84.792364] inet_gso_segment+0x161/0x3e0 [ 84.793071] skb_mac_gso_segment+0xb8/0x120 [ 84.793846] __skb_gso_segment+0x7e/0x180 [ 84.794581] validate_xmit_skb+0x141/0x2e0 [ 84.795297] __dev_queue_xmit+0x258/0x8f0 [ 84.795949] ? eth_header+0x26/0xc0 [ 84.796581] ip_finish_output2+0x196/0x430 [ 84.797295] ? skb_gso_validate_network_len+0x11/0x80 [ 84.798183] ? ip_finish_output+0x169/0x270 [ 84.798875] ip_output+0x6c/0xe0 [ 84.799413] ? ip_append_data.part.50+0xc0/0xc0 [ 84.800145] iptunnel_xmit+0x144/0x1c0 [ 84.800814] ip_tunnel_xmit+0x62d/0x930 [ip_tunnel] [ 84.801699] gre_tap_xmit+0xac/0xf0 [ip_gre] [ 84.802395] dev_hard_start_xmit+0xa5/0x210 [ 84.803086] sch_direct_xmit+0x14f/0x340 [ 84.803733] __dev_queue_xmit+0x799/0x8f0 [ 84.804472] ip_finish_output2+0x2e0/0x430 [ 84.805255] ? skb_gso_validate_network_len+0x11/0x80 [ 84.806154] ip_output+0x6c/0xe0 [ 84.806721] ? ip_append_data.part.50+0xc0/0xc0 [ 84.807516] sctp_packet_transmit+0x716/0xa10 [sctp] [ 84.808337] sctp_outq_flush+0xd7/0x880 [sctp] It was caused by SKB_GSO_CB(skb)->csum_start not set in sctp_gso_segment. sctp_gso_segment() calls skb_segment() with 'feature | NETIF_F_HW_CSUM', which causes SKB_GSO_CB(skb)->csum_start not to be set in skb_segment(). For TCP/UDP, when feature supports HW_CSUM, CHECKSUM_PARTIAL will be set and gso_reset_checksum will be called to set SKB_GSO_CB(skb)->csum_start. So SCTP should do the same as TCP/UDP, to call gso_reset_checksum() when computing checksum in sctp_gso_segment. Reported-by:
Jianlin Shi <jishi@redhat.com> Signed-off-by:
Xin Long <lucien.xin@gmail.com> Acked-by:
Neil Horman <nhorman@tuxdriver.com> Acked-by:
Marcelo Ricardo Leitner <marcelo.leitner@gmail.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
git://git.kernel.org/pub/scm/linux/kernel/git/pablo/nfDavid S. Miller authored
Pablo Neira Ayuso says: ==================== Netfilter/IPVS fixes for net The following patchset contains Netfilter/IPVS fixes for net: 1) Missing structure initialization in ebtables causes splat with 32-bit user level on a 64-bit kernel, from Francesco Ruggeri. 2) Missing dependency on nf_defrag in IPVS IPv6 codebase, from Andrea Claudi. 3) Fix possible use-after-free from release path of target extensions. ==================== Signed-off-by:
David S. Miller <davem@davemloft.net>
-
git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linuxDavid S. Miller authored
Saeed Mahameed says: ==================== Mellanox, mlx5 fixes 2019-02-13 This series introduces some fixes to mlx5 driver. For more information please see tag log below. ==================== Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Saeed Mahameed authored
Currently mlx5 driver creates xdp redirect hw queues unconditionally on netdevice open, This is great until someone starts redirecting XDP traffic via ndo_xdp_xmit on mlx5 device and changes the device configuration at the same time, this might cause crashes, since the other device's napi is not aware of the mlx5 state change (resources un-availability). To fix this we must synchronize with other devices napi's on the system. Added a new flag under mlx5e_priv to determine XDP TX resources are available, set/clear it up when necessary and use synchronize_rcu() when the flag is turned off, so other napi's are in-sync with it, before we actually cleanup the hw resources. The flag is tested prior to committing to transmit on mlx5e_xdp_xmit, and it is sufficient to determine if it safe to transmit or not. The other two internal flags (MLX5E_STATE_OPENED and MLX5E_SQ_STATE_ENABLED) become unnecessary. Thus, they are removed from data path. Fixes: 58b99ee3 ("net/mlx5e: Add support for XDP_REDIRECT in device-out side") Reported-by:
Toke Høiland-Jørgensen <toke@redhat.com> Reviewed-by:
Tariq Toukan <tariqt@mellanox.com> Signed-off-by:
Saeed Mahameed <saeedm@mellanox.com>
-
Tariq Toukan authored
Eliminate the following compilation warning: drivers/net/ethernet/mellanox/mlx5/core/events.c: warning: 'error_str' may be used uninitialized in this function [-Wuninitialized]: => 238:3 Fixes: c2fb3db2 ("net/mlx5: Rework handling of port module events") Signed-off-by:
Tariq Toukan <tariqt@mellanox.com> Reviewed-by:
Mikhael Goikhman <migo@mellanox.com> Signed-off-by:
Saeed Mahameed <saeedm@mellanox.com>
-
Huy Nguyen authored
When EEH is injected and PCI bus stalls, mlx5's pci error detect function is called to deactivate the command interface and tear down the device. The issue is that there can be a thread that already passed MLX5_DEVICE_STATE_INTERNAL_ERROR check, it will send the command and stuck in the wait_func. Solution: Add function mlx5_cmd_flush to disable command interface and clear all the pending commands. When device state is set to MLX5_DEVICE_STATE_INTERNAL_ERROR, call mlx5_cmd_flush to ensure all pending threads waiting for firmware commands completion are terminated. Fixes: c1d4d2e9 ("net/mlx5: Avoid calling sleeping function by the health poll thread") Signed-off-by:
Huy Nguyen <huyn@mellanox.com> Reviewed-by:
Daniel Jurgens <danielj@mellanox.com> Signed-off-by:
Saeed Mahameed <saeedm@mellanox.com>
-
Maria Pasechnik authored
New channels are applied to the priv channels only after they are successfully opened. Then, the indirection table should be built according to the new number of channels. Currently, such build is preformed independently of whether the channels opening is successful, and is not reverted on failure. The bug is caused due to removal of rss params from channels struct and moving it to priv struct. That change cause to independency between channels and rss params. This causes a crash on a later point, when accessing rqn of a non existing channel. This patch fixes it by moving the indirection table build right before switching the priv channels to new channels struct, after the new set of channels was successfully opened. Fixes: bbeb53b8 ("net/mlx5e: Move RSS params to a dedicated struct") Signed-off-by:
Maria Pasechnik <mariap@mellanox.com> Reviewed-by:
Tariq Toukan <tariqt@mellanox.com> Signed-off-by:
Saeed Mahameed <saeedm@mellanox.com>
-
Pablo Neira Ayuso authored
Fetch pointer to module before target object is released. Fixes: 29e38801 ("netfilter: nf_tables: fix use-after-free when deleting compat expressions") Fixes: 0ca743a5 ("netfilter: nf_tables: add compatibility layer for x_tables") Signed-off-by:
Pablo Neira Ayuso <pablo@netfilter.org>
-
- Feb 13, 2019
-
-
Cong Wang authored
The current opt_inst_list operations inside team_nl_cmd_options_set() is too complex to track: LIST_HEAD(opt_inst_list); nla_for_each_nested(...) { list_for_each_entry(opt_inst, &team->option_inst_list, list) { if (__team_option_inst_tmp_find(&opt_inst_list, opt_inst)) continue; list_add(&opt_inst->tmp_list, &opt_inst_list); } } team_nl_send_event_options_get(team, &opt_inst_list); as while we retrieve 'opt_inst' from team->option_inst_list, it could be added to the local 'opt_inst_list' for multiple times. The __team_option_inst_tmp_find() doesn't work, as the setter team_mode_option_set() still calls team->ops.exit() which uses ->tmp_list too in __team_options_change_check(). Simplify the list operations by moving the 'opt_inst_list' and team_nl_send_event_options_get() into the nla_for_each_nested() loop so that it can be guranteed that we won't insert a same list entry for multiple times. Therefore, __team_option_inst_tmp_find() can be removed too. Fixes: 4fb0534f ("team: avoid adding twice the same option to the event list") Fixes: 2fcdb2c9 ("team: allow to send multiple set events in one message") Reported-by:
<syzbot+4d4af685432dc0e56c91@syzkaller.appspotmail.com> Reported-by:
<syzbot+68ee510075cf64260cc4@syzkaller.appspotmail.com> Cc: Jiri Pirko <jiri@resnulli.us> Cc: Paolo Abeni <pabeni@redhat.com> Signed-off-by:
Cong Wang <xiyou.wangcong@gmail.com> Acked-by:
Jiri Pirko <jiri@mellanox.com> Reviewed-by:
Paolo Abeni <pabeni@redhat.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
David S. Miller authored
Cong Wang says: ==================== net_sched: some fixes for cls_tcindex This patchset contains 3 bug fixes for tcindex filter. Please check each patch for details. v2: fix a compile error in patch 2 drop netns refcnt in patch 1 ==================== Signed-off-by:
Cong Wang <xiyou.wangcong@gmail.com>
-
Cong Wang authored
struct tcindex_filter_result contains two parts: struct tcf_exts and struct tcf_result. For the local variable 'cr', its exts part is never used but initialized without being released properly on success path. So just completely remove the exts part to fix this leak. For the local variable 'new_filter_result', it is never properly released if not used by 'r' on success path. Cc: Jamal Hadi Salim <jhs@mojatatu.com> Cc: Jiri Pirko <jiri@resnulli.us> Signed-off-by:
Cong Wang <xiyou.wangcong@gmail.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Cong Wang authored
When tcindex_destroy() destroys all the filter results in the perfect hash table, it invokes the walker to delete each of them. However, results with class==0 are skipped in either tcindex_walk() or tcindex_delete(), which causes a memory leak reported by kmemleak. This patch fixes it by skipping the walker and directly deleting these filter results so we don't miss any filter result. As a result of this change, we have to initialize exts->net properly in tcindex_alloc_perfect_hash(). For net-next, we need to consider whether we should initialize ->net in tcf_exts_init() instead, before that just directly test CONFIG_NET_CLS_ACT=y. Cc: Jamal Hadi Salim <jhs@mojatatu.com> Cc: Jiri Pirko <jiri@resnulli.us> Signed-off-by:
Cong Wang <xiyou.wangcong@gmail.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Cong Wang authored
tcindex_destroy() invokes tcindex_destroy_element() via a walker to delete each filter result in its perfect hash table, and tcindex_destroy_element() calls tcindex_delete() which schedules tcf RCU works to do the final deletion work. Unfortunately this races with the RCU callback __tcindex_destroy(), which could lead to use-after-free as reported by Adrian. Fix this by migrating this RCU callback to tcf RCU work too, as that workqueue is ordered, we will not have use-after-free. Note, we don't need to hold netns refcnt because we don't call tcf_exts_destroy() here. Fixes: 27ce4f05 ("net_sched: use tcf_queue_work() in tcindex filter") Reported-by:
Adrian <bugs@abtelecom.ro> Cc: Ben Hutchings <ben@decadent.org.uk> Cc: Jamal Hadi Salim <jhs@mojatatu.com> Cc: Jiri Pirko <jiri@resnulli.us> Signed-off-by:
Cong Wang <xiyou.wangcong@gmail.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
David S. Miller authored
Arthur Kiyanovski says: ==================== net: ena: race condition bug fix and version update This patchset includes a fix to a race condition that can cause kernel panic, as well as a driver version update because of this fix. ==================== Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Arthur Kiyanovski authored
Update driver version due to bug fix. Signed-off-by:
Arthur Kiyanovski <akiyano@amazon.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Arthur Kiyanovski authored
Fix race condition between ena_update_on_link_change() and ena_restore_device(). This race can occur if link notification arrives while the driver is performing a reset sequence. In this case link can be set up, enabling the device, before it is fully restored. If packets are sent at this time, the driver might access uninitialized data structures, causing kernel crash. Move the clearing of ENA_FLAG_ONGOING_RESET and netif_carrier_on() after ena_up() to ensure the device is ready when link is set up. Fixes: d18e4f68 ("net: ena: fix race condition between device reset and link up setup") Signed-off-by:
Arthur Kiyanovski <akiyano@amazon.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Kal Conley authored
When calculating rb->frames_per_block * req->tp_block_nr the result can overflow. Check it for overflow without limiting the total buffer size to UINT_MAX. This change fixes support for packet ring buffers >= UINT_MAX. Fixes: 8f8d28e4 ("net/packet: fix overflow in check for tp_frame_nr") Signed-off-by:
Kal Conley <kal.conley@dectris.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Konstantin Khlebnikov authored
Field idiag_ext in struct inet_diag_req_v2 used as bitmap of requested extensions has only 8 bits. Thus extensions starting from DCTCPINFO cannot be requested directly. Some of them included into response unconditionally or hook into some of lower 8 bits. Extension INET_DIAG_CLASS_ID has not way to request from the beginning. This patch bundle it with INET_DIAG_TCLASS (ipv6 tos), fixes space reservation, and documents behavior for other extensions. Also this patch adds fallback to reporting socket priority. This filed is more widely used for traffic classification because ipv4 sockets automatically maps TOS to priority and default qdisc pfifo_fast knows about that. But priority could be changed via setsockopt SO_PRIORITY so INET_DIAG_TOS isn't enough for predicting class. Also cgroup2 obsoletes net_cls classid (it always zero), but we cannot reuse this field for reporting cgroup2 id because it is 64-bit (ino+gen). So, after this patch INET_DIAG_CLASS_ID will report socket priority for most common setup when net_cls isn't set and/or cgroup2 in use. Fixes: 0888e372 ("net: inet: diag: expose sockets cgroup classid") Signed-off-by:
Konstantin Khlebnikov <khlebnikov@yandex-team.ru> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Eric Dumazet authored
KMSAN reported batadv_interface_tx() was possibly using a garbage value [1] batadv_get_vid() does have a pskb_may_pull() call but batadv_interface_tx() does not actually make sure this did not fail. [1] BUG: KMSAN: uninit-value in batadv_interface_tx+0x908/0x1e40 net/batman-adv/soft-interface.c:231 CPU: 0 PID: 10006 Comm: syz-executor469 Not tainted 4.20.0-rc7+ #5 Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011 Call Trace: __dump_stack lib/dump_stack.c:77 [inline] dump_stack+0x173/0x1d0 lib/dump_stack.c:113 kmsan_report+0x12e/0x2a0 mm/kmsan/kmsan.c:613 __msan_warning+0x82/0xf0 mm/kmsan/kmsan_instr.c:313 batadv_interface_tx+0x908/0x1e40 net/batman-adv/soft-interface.c:231 __netdev_start_xmit include/linux/netdevice.h:4356 [inline] netdev_start_xmit include/linux/netdevice.h:4365 [inline] xmit_one net/core/dev.c:3257 [inline] dev_hard_start_xmit+0x607/0xc40 net/core/dev.c:3273 __dev_queue_xmit+0x2e42/0x3bc0 net/core/dev.c:3843 dev_queue_xmit+0x4b/0x60 net/core/dev.c:3876 packet_snd net/packet/af_packet.c:2928 [inline] packet_sendmsg+0x8306/0x8f30 net/packet/af_packet.c:2953 sock_sendmsg_nosec net/socket.c:621 [inline] sock_sendmsg net/socket.c:631 [inline] __sys_sendto+0x8c4/0xac0 net/socket.c:1788 __do_sys_sendto net/socket.c:1800 [inline] __se_sys_sendto+0x107/0x130 net/socket.c:1796 __x64_sys_sendto+0x6e/0x90 net/socket.c:1796 do_syscall_64+0xbc/0xf0 arch/x86/entry/common.c:291 entry_SYSCALL_64_after_hwframe+0x63/0xe7 RIP: 0033:0x441889 Code: 18 89 d0 c3 66 2e 0f 1f 84 00 00 00 00 00 0f 1f 00 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 0f 83 bb 10 fc ff c3 66 2e 0f 1f 84 00 00 00 00 RSP: 002b:00007ffdda6fd468 EFLAGS: 00000216 ORIG_RAX: 000000000000002c RAX: ffffffffffffffda RBX: 0000000000000002 RCX: 0000000000441889 RDX: 000000000000000e RSI: 00000000200000c0 RDI: 0000000000000003 RBP: 0000000000000003 R08: 0000000000000000 R09: 0000000000000000 R10: 0000000000000000 R11: 0000000000000216 R12: 00007ffdda6fd4c0 R13: 00007ffdda6fd4b0 R14: 0000000000000000 R15: 0000000000000000 Uninit was created at: kmsan_save_stack_with_flags mm/kmsan/kmsan.c:204 [inline] kmsan_internal_poison_shadow+0x92/0x150 mm/kmsan/kmsan.c:158 kmsan_kmalloc+0xa6/0x130 mm/kmsan/kmsan_hooks.c:176 kmsan_slab_alloc+0xe/0x10 mm/kmsan/kmsan_hooks.c:185 slab_post_alloc_hook mm/slab.h:446 [inline] slab_alloc_node mm/slub.c:2759 [inline] __kmalloc_node_track_caller+0xe18/0x1030 mm/slub.c:4383 __kmalloc_reserve net/core/skbuff.c:137 [inline] __alloc_skb+0x309/0xa20 net/core/skbuff.c:205 alloc_skb include/linux/skbuff.h:998 [inline] alloc_skb_with_frags+0x1c7/0xac0 net/core/skbuff.c:5220 sock_alloc_send_pskb+0xafd/0x10e0 net/core/sock.c:2083 packet_alloc_skb net/packet/af_packet.c:2781 [inline] packet_snd net/packet/af_packet.c:2872 [inline] packet_sendmsg+0x661a/0x8f30 net/packet/af_packet.c:2953 sock_sendmsg_nosec net/socket.c:621 [inline] sock_sendmsg net/socket.c:631 [inline] __sys_sendto+0x8c4/0xac0 net/socket.c:1788 __do_sys_sendto net/socket.c:1800 [inline] __se_sys_sendto+0x107/0x130 net/socket.c:1796 __x64_sys_sendto+0x6e/0x90 net/socket.c:1796 do_syscall_64+0xbc/0xf0 arch/x86/entry/common.c:291 entry_SYSCALL_64_after_hwframe+0x63/0xe7 Fixes: c6c8fea2 ("net: Add batman-adv meshing protocol") Signed-off-by:
Eric Dumazet <edumazet@google.com> Reported-by:
syzbot <syzkaller@googlegroups.com> Cc: Marek Lindner <mareklindner@neomailbox.ch> Cc: Simon Wunderlich <sw@simonwunderlich.de> Cc: Antonio Quartulli <a@unstable.cc> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Li RongQing authored
genlmsg_reply can fail, so propagate its return code Fixes: 915d7e5e ("ipv6: sr: add code base for control plane support of SR-IPv6") Signed-off-by:
Li RongQing <lirongqing@baidu.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Saeed Mahameed authored
When an ethernet frame is padded to meet the minimum ethernet frame size, the padding octets are not covered by the hardware checksum. Fortunately the padding octets are usually zero's, which don't affect checksum. However, it is not guaranteed. For example, switches might choose to make other use of these octets. This repeatedly causes kernel hardware checksum fault. Prior to the cited commit below, skb checksum was forced to be CHECKSUM_NONE when padding is detected. After it, we need to keep skb->csum updated. However, fixing up CHECKSUM_COMPLETE requires to verify and parse IP headers, it does not worth the effort as the packets are so small that CHECKSUM_COMPLETE has no significant advantage. Future work: when reporting checksum complete is not an option for IP non-TCP/UDP packets, we can actually fallback to report checksum unnecessary, by looking at cqe IPOK bit. Fixes: 88078d98 ("net: pskb_trim_rcsum() and CHECKSUM_COMPLETE are friends") Cc: Eric Dumazet <edumazet@google.com> Signed-off-by:
Saeed Mahameed <saeedm@mellanox.com> Signed-off-by:
Tariq Toukan <tariqt@mellanox.com> Reviewed-by:
Eric Dumazet <edumazet@google.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Russell King authored
During testing on Armada 388 platforms, it was found with a certain module configuration that it was possible to trigger a kernel oops during the module load process, caused by the phylink resolver being triggered for a currently disabled interface. This problem was introduced by changing the way the SFP registration works, which now can result in the sfp link down notification being called during phylink_create(). Fixes: b5bfc21a ("net: sfp: do not probe SFP module before we're attached") Signed-off-by:
Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Matteo Croce authored
Due to the depends on NET_UDP_TUNNEL, at the moment it is impossible to compile GENEVE if no other protocol depending on NET_UDP_TUNNEL is selected. Fix this changing the depends to a select, and drop NET_IP_TUNNEL from the select list, as it already depends on NET_UDP_TUNNEL. Signed-off-by:
Matteo Croce <mcroce@redhat.com> Reviewed-and-tested-by:
Andrea Claudi <aclaudi@redhat.com> Tested-by:
Davide Caratti <dcaratti@redhat.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Bert Kenward authored
The bitmap of found partitions in efx_ef10_mtd_probe was not initialised, causing partitions to be suppressed based off whatever value was in the bitmap at the start. Fixes: 33664635 ("sfc: suppress duplicate nvmem partition types in efx_ef10_mtd_probe") Signed-off-by:
Bert Kenward <bkenward@solarflare.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
David S. Miller authored
Merge tag 'mac80211-for-davem-2019-02-12' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211 Johannes Berg says: ==================== Just a few fixes: * aggregation session teardown with internal TXQs was continuing to send some frames marked as aggregation, fix from Ilan * IBSS join was missed during firmware restart, should such a thing happen * speculative execution based on the return value of cfg80211_classify8021d() - which is controlled by the sender of the packet - could be problematic in some code using it, prevent it * a few peer measurement fixes ==================== Signed-off-by:
David S. Miller <davem@davemloft.net>
-
- Feb 12, 2019
-
-
Andrea Claudi authored
ipvs relies on nf_defrag_ipv6 module to manage IPv6 fragmentation, but lacks proper Kconfig dependencies and does not explicitly request defrag features. As a result, if netfilter hooks are not loaded, when IPv6 fragmented packet are handled by ipvs only the first fragment makes through. Fix it properly declaring the dependency on Kconfig and registering netfilter hooks on ip_vs_add_service() and ip_vs_new_dest(). Reported-by:
Li Shuang <shuali@redhat.com> Signed-off-by:
Andrea Claudi <aclaudi@redhat.com> Acked-by:
Julian Anastasov <ja@ssi.bg> Acked-by:
Simon Horman <horms@verge.net.au> Signed-off-by:
Pablo Neira Ayuso <pablo@netfilter.org>
-
Tuong Lien authored
When a link endpoint is re-created (e.g. after a node reboot or interface reset), the link session number is varied by random, the peer endpoint will be synced with this new session number before the link is re-established. However, there is a shortcoming in this mechanism that can lead to the link never re-established or faced with a failure then. It happens when the peer endpoint is ready in ESTABLISHING state, the 'peer_session' as well as the 'in_session' flag have been set, but suddenly this link endpoint leaves. When it comes back with a random session number, there are two situations possible: 1/ If the random session number is larger than (or equal to) the previous one, the peer endpoint will be updated with this new session upon receipt of a RESET_MSG from this endpoint, and the link can be re- established as normal. Otherwise, all the RESET_MSGs from this endpoint will be rejected by the peer. In turn, when this link endpoint receives one ACTIVATE_MSG from the peer, it will move to ESTABLISHED and start to send STATE_MSGs, but again these messages will be dropped by the peer due to wrong session. The peer link endpoint can still become ESTABLISHED after receiving a traffic message from this endpoint (e.g. a BCAST_PROTOCOL or NAME_DISTRIBUTOR), but since all the STATE_MSGs are invalid, the link will be forced down sooner or later! Even in case the random session number is larger than the previous one, it can be that the ACTIVATE_MSG from the peer arrives first, and this link endpoint moves quickly to ESTABLISHED without sending out any RESET_MSG yet. Consequently, the peer link will not be updated with the new session number, and the same link failure scenario as above will happen. 2/ Another situation can be that, the peer link endpoint was reset due to any reasons in the meantime, its link state was set to RESET from ESTABLISHING but still in session, i.e. the 'in_session' flag is not reset... Now, if the random session number from this endpoint is less than the previous one, all the RESET_MSGs from this endpoint will be rejected by the peer. In the other direction, when this link endpoint receives a RESET_MSG from the peer, it moves to ESTABLISHING and starts to send ACTIVATE_MSGs, but all these messages will be rejected by the peer too. As a result, the link cannot be re-established but gets stuck with this link endpoint in state ESTABLISHING and the peer in RESET! Solution: =========== This link endpoint should not go directly to ESTABLISHED when getting ACTIVATE_MSG from the peer which may belong to the old session if the link was re-created. To ensure the session to be correct before the link is re-established, the peer endpoint in ESTABLISHING state will send back the last session number in ACTIVATE_MSG for a verification at this endpoint. Then, if needed, a new and more appropriate session number will be regenerated to force a re-synch first. In addition, when a link in ESTABLISHING state is reset, its state will move to RESET according to the link FSM, along with resetting the 'in_session' flag (and the other data) as a normal link reset, it will also be deleted if requested. The solution is backward compatible. Acked-by:
Jon Maloy <jon.maloy@ericsson.com> Acked-by:
Ying Xue <ying.xue@windriver.com> Signed-off-by:
Tuong Lien <tuong.t.lien@dektech.com.au> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Zhiqiang Liu authored
Follow those steps: # ip addr add 2001:123::1/32 dev eth0 # ip addr add 2001:123:456::2/64 dev eth0 # ip addr del 2001:123::1/32 dev eth0 # ip addr del 2001:123:456::2/64 dev eth0 and then prefix route of 2001:123::1/32 will still exist. This is because ipv6_prefix_equal in check_cleanup_prefix_route func does not check whether two IPv6 addresses have the same prefix length. If the prefix of one address starts with another shorter address prefix, even though their prefix lengths are different, the return value of ipv6_prefix_equal is true. Here I add a check of whether two addresses have the same prefix to decide whether their prefixes are equal. Fixes: 5b84efec ("ipv6 addrconf: don't cleanup prefix route for IFA_F_NOPREFIXROUTE") Signed-off-by:
Zhiqiang Liu <liuzhiqiang26@huawei.com> Reported-by:
Wenhao Zhang <zhangwenhao8@huawei.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Hoang Le authored
When we free skb at tipc_data_input, we return a 'false' boolean. Then, skb passed to subcalling tipc_link_input in tipc_link_rcv, <snip> 1303 int tipc_link_rcv: ... 1354 if (!tipc_data_input(l, skb, l->inputq)) 1355 rc |= tipc_link_input(l, skb, l->inputq); </snip> Fix it by simple changing to a 'true' boolean when skb is being free-ed. Then, tipc_link_rcv will bypassed to subcalling tipc_link_input as above condition. Acked-by:
Ying Xue <ying.xue@windriver.com> Acked-by:
Jon Maloy <maloy@donjonn.com> Signed-off-by:
Hoang Le <hoang.h.le@dektech.com.au> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Francesco Ruggeri authored
If a non zero value happens to be in xt[NFPROTO_BRIDGE].cur at init time, the following panic can be caused by running % ebtables -t broute -F BROUTING from a 32-bit user level on a 64-bit kernel. This patch replaces kmalloc_array with kcalloc when allocating xt. [ 474.680846] BUG: unable to handle kernel paging request at 0000000009600920 [ 474.687869] PGD 2037006067 P4D 2037006067 PUD 2038938067 PMD 0 [ 474.693838] Oops: 0000 [#1] SMP [ 474.697055] CPU: 9 PID: 4662 Comm: ebtables Kdump: loaded Not tainted 4.19.17-11302235.AroraKernelnext.fc18.x86_64 #1 [ 474.707721] Hardware name: Supermicro X9DRT/X9DRT, BIOS 3.0 06/28/2013 [ 474.714313] RIP: 0010:xt_compat_calc_jump+0x2f/0x63 [x_tables] [ 474.720201] Code: 40 0f b6 ff 55 31 c0 48 6b ff 70 48 03 3d dc 45 00 00 48 89 e5 8b 4f 6c 4c 8b 47 60 ff c9 39 c8 7f 2f 8d 14 08 d1 fa 48 63 fa <41> 39 34 f8 4c 8d 0c fd 00 00 00 00 73 05 8d 42 01 eb e1 76 05 8d [ 474.739023] RSP: 0018:ffffc9000943fc58 EFLAGS: 00010207 [ 474.744296] RAX: 0000000000000000 RBX: ffffc90006465000 RCX: 0000000002580249 [ 474.751485] RDX: 00000000012c0124 RSI: fffffffff7be17e9 RDI: 00000000012c0124 [ 474.758670] RBP: ffffc9000943fc58 R08: 0000000000000000 R09: ffffffff8117cf8f [ 474.765855] R10: ffffc90006477000 R11: 0000000000000000 R12: 0000000000000001 [ 474.773048] R13: 0000000000000000 R14: ffffc9000943fcb8 R15: ffffc9000943fcb8 [ 474.780234] FS: 0000000000000000(0000) GS:ffff88a03f840000(0063) knlGS:00000000f7ac7700 [ 474.788612] CS: 0010 DS: 002b ES: 002b CR0: 0000000080050033 [ 474.794632] CR2: 0000000009600920 CR3: 0000002037422006 CR4: 00000000000606e0 [ 474.802052] Call Trace: [ 474.804789] compat_do_replace+0x1fb/0x2a3 [ebtables] [ 474.810105] compat_do_ebt_set_ctl+0x69/0xe6 [ebtables] [ 474.815605] ? try_module_get+0x37/0x42 [ 474.819716] compat_nf_setsockopt+0x4f/0x6d [ 474.824172] compat_ip_setsockopt+0x7e/0x8c [ 474.828641] compat_raw_setsockopt+0x16/0x3a [ 474.833220] compat_sock_common_setsockopt+0x1d/0x24 [ 474.838458] __compat_sys_setsockopt+0x17e/0x1b1 [ 474.843343] ? __check_object_size+0x76/0x19a [ 474.847960] __ia32_compat_sys_socketcall+0x1cb/0x25b [ 474.853276] do_fast_syscall_32+0xaf/0xf6 [ 474.857548] entry_SYSENTER_compat+0x6b/0x7a Signed-off-by:
Francesco Ruggeri <fruggeri@arista.com> Acked-by:
Florian Westphal <fw@strlen.de> Signed-off-by:
Pablo Neira Ayuso <pablo@netfilter.org>
-
Eric Dumazet authored
Due to quadratic behavior of x25_new_lci(), syzbot was able to trigger an rcu stall. Fix this by not blocking BH for the whole duration of the function, and inserting a reschedule point when possible. If we care enough, using a bitmap could get rid of the quadratic behavior. syzbot report : rcu: INFO: rcu_preempt self-detected stall on CPU rcu: 0-...!: (10500 ticks this GP) idle=4fa/1/0x4000000000000002 softirq=283376/283376 fqs=0 rcu: (t=10501 jiffies g=383105 q=136) rcu: rcu_preempt kthread starved for 10502 jiffies! g383105 f0x0 RCU_GP_WAIT_FQS(5) ->state=0x402 ->cpu=0 rcu: RCU grace-period kthread stack dump: rcu_preempt I28928 10 2 0x80000000 Call Trace: context_switch kernel/sched/core.c:2844 [inline] __schedule+0x817/0x1cc0 kernel/sched/core.c:3485 schedule+0x92/0x180 kernel/sched/core.c:3529 schedule_timeout+0x4db/0xfd0 kernel/time/timer.c:1803 rcu_gp_fqs_loop kernel/rcu/tree.c:1948 [inline] rcu_gp_kthread+0x956/0x17a0 kernel/rcu/tree.c:2105 kthread+0x357/0x430 kernel/kthread.c:246 ret_from_fork+0x3a/0x50 arch/x86/entry/entry_64.S:352 NMI backtrace for cpu 0 CPU: 0 PID: 8759 Comm: syz-executor2 Not tainted 5.0.0-rc4+ #51 Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011 Call Trace: <IRQ> __dump_stack lib/dump_stack.c:77 [inline] dump_stack+0x172/0x1f0 lib/dump_stack.c:113 nmi_cpu_backtrace.cold+0x63/0xa4 lib/nmi_backtrace.c:101 nmi_trigger_cpumask_backtrace+0x1be/0x236 lib/nmi_backtrace.c:62 arch_trigger_cpumask_backtrace+0x14/0x20 arch/x86/kernel/apic/hw_nmi.c:38 trigger_single_cpu_backtrace include/linux/nmi.h:164 [inline] rcu_dump_cpu_stacks+0x183/0x1cf kernel/rcu/tree.c:1211 print_cpu_stall kernel/rcu/tree.c:1348 [inline] check_cpu_stall kernel/rcu/tree.c:1422 [inline] rcu_pending kernel/rcu/tree.c:3018 [inline] rcu_check_callbacks.cold+0x500/0xa4a kernel/rcu/tree.c:2521 update_process_times+0x32/0x80 kernel/time/timer.c:1635 tick_sched_handle+0xa2/0x190 kernel/time/tick-sched.c:161 tick_sched_timer+0x47/0x130 kernel/time/tick-sched.c:1271 __run_hrtimer kernel/time/hrtimer.c:1389 [inline] __hrtimer_run_queues+0x33e/0xde0 kernel/time/hrtimer.c:1451 hrtimer_interrupt+0x314/0x770 kernel/time/hrtimer.c:1509 local_apic_timer_interrupt arch/x86/kernel/apic/apic.c:1035 [inline] smp_apic_timer_interrupt+0x120/0x570 arch/x86/kernel/apic/apic.c:1060 apic_timer_interrupt+0xf/0x20 arch/x86/entry/entry_64.S:807 </IRQ> RIP: 0010:__read_once_size include/linux/compiler.h:193 [inline] RIP: 0010:queued_write_lock_slowpath+0x13e/0x290 kernel/locking/qrwlock.c:86 Code: 00 00 fc ff df 4c 8d 2c 01 41 83 c7 03 41 0f b6 45 00 41 38 c7 7c 08 84 c0 0f 85 0c 01 00 00 8b 03 3d 00 01 00 00 74 1a f3 90 <41> 0f b6 55 00 41 38 d7 7c eb 84 d2 74 e7 48 89 df e8 6c 0f 4f 00 RSP: 0018:ffff88805f117bd8 EFLAGS: 00000206 ORIG_RAX: ffffffffffffff13 RAX: 0000000000000300 RBX: ffffffff89413ba0 RCX: 1ffffffff1282774 RDX: 0000000000000000 RSI: 0000000000000004 RDI: ffffffff89413ba0 RBP: ffff88805f117c70 R08: 1ffffffff1282774 R09: fffffbfff1282775 R10: fffffbfff1282774 R11: ffffffff89413ba3 R12: 00000000000000ff R13: fffffbfff1282774 R14: 1ffff1100be22f7d R15: 0000000000000003 queued_write_lock include/asm-generic/qrwlock.h:104 [inline] do_raw_write_lock+0x1d6/0x290 kernel/locking/spinlock_debug.c:203 __raw_write_lock_bh include/linux/rwlock_api_smp.h:204 [inline] _raw_write_lock_bh+0x3b/0x50 kernel/locking/spinlock.c:312 x25_insert_socket+0x21/0xe0 net/x25/af_x25.c:267 x25_bind+0x273/0x340 net/x25/af_x25.c:705 __sys_bind+0x23f/0x290 net/socket.c:1505 __do_sys_bind net/socket.c:1516 [inline] __se_sys_bind net/socket.c:1514 [inline] __x64_sys_bind+0x73/0xb0 net/socket.c:1514 do_syscall_64+0x103/0x610 arch/x86/entry/common.c:290 entry_SYSCALL_64_after_hwframe+0x49/0xbe RIP: 0033:0x457e39 Code: ad b8 fb ff c3 66 2e 0f 1f 84 00 00 00 00 00 66 90 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 0f 83 7b b8 fb ff c3 66 2e 0f 1f 84 00 00 00 00 RSP: 002b:00007fafccd0dc78 EFLAGS: 00000246 ORIG_RAX: 0000000000000031 RAX: ffffffffffffffda RBX: 0000000000000003 RCX: 0000000000457e39 RDX: 0000000000000012 RSI: 0000000020000240 RDI: 0000000000000004 RBP: 000000000073bf00 R08: 0000000000000000 R09: 0000000000000000 R10: 0000000000000000 R11: 0000000000000246 R12: 00007fafccd0e6d4 R13: 00000000004bdf8b R14: 00000000004ce4b8 R15: 00000000ffffffff Sending NMI from CPU 0 to CPUs 1: NMI backtrace for cpu 1 CPU: 1 PID: 8752 Comm: syz-executor4 Not tainted 5.0.0-rc4+ #51 Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011 RIP: 0010:__x25_find_socket+0x78/0x120 net/x25/af_x25.c:328 Code: 89 f8 48 c1 e8 03 80 3c 18 00 0f 85 a6 00 00 00 4d 8b 64 24 68 4d 85 e4 74 7f e8 03 97 3d fb 49 83 ec 68 74 74 e8 f8 96 3d fb <49> 8d bc 24 88 04 00 00 48 89 f8 48 c1 e8 03 0f b6 04 18 84 c0 74 RSP: 0018:ffff8880639efc58 EFLAGS: 00000246 RAX: 0000000000040000 RBX: dffffc0000000000 RCX: ffffc9000e677000 RDX: 0000000000040000 RSI: ffffffff863244b8 RDI: ffff88806a764628 RBP: ffff8880639efc80 R08: ffff8880a80d05c0 R09: fffffbfff1282775 R10: fffffbfff1282774 R11: ffffffff89413ba3 R12: ffff88806a7645c0 R13: 0000000000000001 R14: ffff88809f29ac00 R15: 0000000000000000 FS: 00007fe8d0c58700(0000) GS:ffff8880ae900000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 0000001b32823000 CR3: 00000000672eb000 CR4: 00000000001406e0 DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 Call Trace: x25_new_lci net/x25/af_x25.c:357 [inline] x25_connect+0x374/0xdf0 net/x25/af_x25.c:786 __sys_connect+0x266/0x330 net/socket.c:1686 __do_sys_connect net/socket.c:1697 [inline] __se_sys_connect net/socket.c:1694 [inline] __x64_sys_connect+0x73/0xb0 net/socket.c:1694 do_syscall_64+0x103/0x610 arch/x86/entry/common.c:290 entry_SYSCALL_64_after_hwframe+0x49/0xbe RIP: 0033:0x457e39 Code: ad b8 fb ff c3 66 2e 0f 1f 84 00 00 00 00 00 66 90 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 0f 83 7b b8 fb ff c3 66 2e 0f 1f 84 00 00 00 00 RSP: 002b:00007fe8d0c57c78 EFLAGS: 00000246 ORIG_RAX: 000000000000002a RAX: ffffffffffffffda RBX: 0000000000000003 RCX: 0000000000457e39 RDX: 0000000000000012 RSI: 0000000020000200 RDI: 0000000000000004 RBP: 000000000073bf00 R08: 0000000000000000 R09: 0000000000000000 R10: 0000000000000000 R11: 0000000000000246 R12: 00007fe8d0c586d4 R13: 00000000004be378 R14: 00000000004ceb00 R15: 00000000ffffffff Signed-off-by:
Eric Dumazet <edumazet@google.com> Reported-by:
syzbot <syzkaller@googlegroups.com> Cc: Andrew Hendry <andrew.hendry@gmail.com> Cc: linux-x25@vger.kernel.org Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Eric Dumazet authored
netif_rx() must be called under a strict contract. At device dismantle phase, core networking clears IFF_UP and flush_all_backlogs() is called after rcu grace period to make sure no incoming packet might be in a cpu backlog and still referencing the device. Most drivers call netif_rx() from their interrupt handler, and since the interrupts are disabled at device dismantle, netif_rx() does not have to check dev->flags & IFF_UP Virtual drivers do not have this guarantee, and must therefore make the check themselves. Otherwise we risk use-after-free and/or crashes. Note this patch also fixes a small issue that came with commit ce6502a8 ("vxlan: fix a use after free in vxlan_encap_bypass"), since the dev->stats.rx_dropped change was done on the wrong device. Fixes: d342894c ("vxlan: virtual extensible lan") Fixes: ce6502a8 ("vxlan: fix a use after free in vxlan_encap_bypass") Signed-off-by:
Eric Dumazet <edumazet@google.com> Cc: Petr Machata <petrm@mellanox.com> Cc: Ido Schimmel <idosch@mellanox.com> Cc: Roopa Prabhu <roopa@cumulusnetworks.com> Cc: Stefano Brivio <sbrivio@redhat.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Jouke Witteveen authored
Netlink has moved from bitmasks to group numbers long ago. Signed-off-by:
Jouke Witteveen <j.witteveen@gmail.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
git://git.kernel.org/pub/scm/linux/kernel/git/pablo/nfDavid S. Miller authored
Pablo Neira Ayuso says: ==================== Netfilter fixes for net The following patchset contains Netfilter fixes for net: 1) Out-of-bound access to packet data from the snmp nat helper, from Jann Horn. 2) ICMP(v6) error packets are set as related traffic by conntrack, update protocol number before calling nf_nat_ipv4_manip_pkt() to use ICMP(v6) rather than the original protocol number, from Florian Westphal. ==================== Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Florian Westphal authored
Sander Eikelenboom bisected a NAT related regression down to the l4proto->manip_pkt indirection removal. I forgot that ICMP(v6) errors (e.g. PKTTOOBIG) can be set as related to the existing conntrack entry. Therefore, when passing the skb to nf_nat_ipv4/6_manip_pkt(), that ended up calling the wrong l4 manip function, as tuple->dst.protonum is the original flows l4 protocol (TCP, UDP, etc). Set the dst protocol field to ICMP(v6), we already have a private copy of the tuple due to the inversion of src/dst. Reported-by:
Sander Eikelenboom <linux@eikelenboom.it> Tested-by:
Sander Eikelenboom <linux@eikelenboom.it> Fixes: faec18db ("netfilter: nat: remove l4proto->manip_pkt") Signed-off-by:
Florian Westphal <fw@strlen.de> Signed-off-by:
Pablo Neira Ayuso <pablo@netfilter.org>
-
Jann Horn authored
The generic ASN.1 decoder infrastructure doesn't guarantee that callbacks will get as much data as they expect; callbacks have to check the `datalen` parameter before looking at `data`. Make sure that snmp_version() and snmp_helper() don't read/write beyond the end of the packet data. (Also move the assignment to `pdata` down below the check to make it clear that it isn't necessarily a pointer we can use before the `datalen` check.) Fixes: cc2d5863 ("netfilter: nf_nat_snmp_basic: use asn1 decoder library") Signed-off-by:
Jann Horn <jannh@google.com> Signed-off-by:
Pablo Neira Ayuso <pablo@netfilter.org>
-