Pinmuxing for DRA7x/AM57x family of processors need to be done in IO
isolation as part of initial bootloader executed from SRAM. This is
done as part of iodelay configuration sequence and is required due
to the limitations introduced by erratum ID: i869[1] (IO Glitches
can occur when changing IO settings) and elaborated in the Technical
Reference Manual[2] 18.4.6.1.7 Isolation Requirements.

Only peripheral that is permitted for dynamic pin mux configuration
is MMC and DCAN. MMC is permitted to change to accommodate the
requirements for varied speeds (which require IO-delay support in
kernel as well). DCAN is a result of i893[1] (DCAN initialization
sequence). However, since we don't use DCAN on X15, with the exception
of MMC, all other pin mux configurations are removed from the dts.

[1] http://www.ti.com/lit/pdf/sprz429
[2] http://www.ti.com/lit/pdf/sprui30

Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

The LEDs on igepv5 are on the GPIO expander unlike on omap5-uevm.

Configuration copied from git.isee.biz git tree except fixed for
red and blue mapping.

Signed-off-by: Tony Lindgren <tony@atomide.com>

Add power button support for igepv5.

Cc: Agustí Fontquerni i Gorchs <afontquerni@iseebcn.com>
Cc: Enric Balletbo Serra <eballetbo@gmail.com>
Cc: Javier Martinez Canillas <javier@osg.samsung.com>
Cc: Pau Pajuel <ppajuel@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

The ID pin GPIO comes from the PMIC. Let's configure it as a GPIO
for the driver to use, and also make sure the PMIC GPIO pin muxing
is correct. The PMIC pad1 and 2 values for omap5-uevm and igepv5 are
0x5a and 0x1b, we only need to clear bit 2 in pad1 register to make
the ID pin GPIO work.

Signed-off-by: Tony Lindgren <tony@atomide.com>

Few changes to fix issues I've noticed while debugging omap5-uevm
wl18xx issues:

1. Move wlcore irq pin muxing under wlcore. This irq could be
   different from gpio_wk14 on some board variants

2. Don't configure pull on wlcore irq pin. There is a 10k
   pull up resistor R105 on the device to VDDS_1v8_MAIN

3. The padconf register for wlsdio_data1 is wrong, it's really
   at 0x1a8 + 2 - 0x40 = 0x16a offset, not at 0x168 as that's
   for wlsdio_data0

4. Mark the omap5-uevm wlan as compatible with ti,wl1837 as
   that's what the TDK R078 part seems to be

5. The MMC interrupt for WLAN musb be wakeupgen, not gic

Looks like omap5-uevm WLAN behaves better now, but I still seem
to have issues with some access points.

Signed-off-by: Tony Lindgren <tony@atomide.com>

Otherwise we have delays on noticing interrupts from the
WLAN card when idle.

Signed-off-by: Tony Lindgren <tony@atomide.com>

This patch fixes the following DTC warnings:

"Node /memory has a reg or ranges property, but no unit name"

Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

This patch fixes the following DTC warnings:

"Node /memory has a reg or ranges property, but no unit name"

Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

This patch fixes the following DTC warnings:

"Node /memory has a reg or ranges property, but no unit name"

Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

This patch fixes the following DTC warnings:

"Node /memory has a reg or ranges property, but no unit name"

Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

This patch fixes the following DTC warnings:

"Node /memory has a reg or ranges property, but no unit name"

Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

This patch fixes the following DTC warnings:

"Node /memory has a reg or ranges property, but no unit name"

Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

This patch fixes the following DTC warnings:

"Node /memory has a reg or ranges property, but no unit name"

Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

This patch fixes the following DTC warnings:

"Node /memory has a reg or ranges property, but no unit name"

Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

This patch fixes the following DTC warnings:

"Node /memory has a reg or ranges property, but no unit name"

Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

This patch fixes the following DTC warnings:

"Node /memory has a reg or ranges property, but no unit name"

Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

This patch fixes the following DTC warnings:

"Node /memory has a reg or ranges property, but no unit name"

Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

This patch fixes the following DTC warnings:

"Node /memory has a reg or ranges property, but no unit name"

Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

The skeleton.dtsi file was removed in ARM64 for different reasons as
explained in commit ("3ebee5a2

 arm64: dts: kill skeleton.dtsi").

These also applies to ARM and it will also allow to get rid of the
following DTC warnings in the future:

"Node /memory has a reg or ranges property, but no unit name"

The disassembled DTB are almost the same besides an empty chosen
node being removed and nodes reordered, so it shouldn't have
functional changes.

Since no am4372 based board had a memory node defined, a dummy node
is added so the compiled DTB memory node is the same than before.

Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

The skeleton.dtsi file was removed in ARM64 for different reasons as
explained in commit ("3ebee5a2

 arm64: dts: kill skeleton.dtsi").

These also applies to ARM and it will also allow to get rid of the
following DTC warnings in the future:

"Node /memory has a reg or ranges property, but no unit name"

The disassembled DTB are almost the same besides an empty chosen
node being removed and nodes reordered, so it should not have
functional changes.

Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

The skeleton.dtsi file was removed in ARM64 for different reasons as
explained in commit ("3ebee5a2

 arm64: dts: kill skeleton.dtsi").

These also applies to ARM and it will also allow to get rid of the
following DTC warnings in the future:

"Node /memory has a reg or ranges property, but no unit name"

The disassembled DTB are almost the same besides an empty chosen
node being removed and nodes reordered, so it should not have
functional changes.

Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

The skeleton.dtsi file was removed in ARM64 for different reasons as
explained in commit ("3ebee5a2

 arm64: dts: kill skeleton.dtsi").

These also applies to ARM and it will also allow to get rid of the
following DTC warnings in the future:

"Node /memory has a reg or ranges property, but no unit name"

The disassembled DTB are almost the same besides an empty chosen
node being removed and nodes reordered, so it should not have
functional changes.

Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

The skeleton.dtsi file was removed in ARM64 for different reasons as
explained in commit ("3ebee5a2

 arm64: dts: kill skeleton.dtsi").

These also applies to ARM and it will also allow to get rid of the
following DTC warnings in the future:

"Node /memory has a reg or ranges property, but no unit name"

The disassembled DTB are almost the same besides an empty chosen
node being removed and nodes reordered, so it should not have
functional changes.

Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

The skeleton.dtsi file was removed in ARM64 for different reasons as
explained in commit ("3ebee5a2

 arm64: dts: kill skeleton.dtsi").

These also applies to ARM and it will also allow to get rid of the
following DTC warnings in the future:

"Node /memory has a reg or ranges property, but no unit name"

The disassembled DTB are almost the same besides an empty chosen
node being removed and nodes reordered, so it should not have
functional changes.

Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

The skeleton.dtsi file was removed in ARM64 for different reasons as
explained in commit ("3ebee5a2

 arm64: dts: kill skeleton.dtsi").

These also applies to ARM and it will also allow to get rid of the
following DTC warnings in the future:

"Node /memory has a reg or ranges property, but no unit name"

The disassembled DTB are almost the same besides an empty chosen
node being removed and nodes reordered, so it should not have
functional changes.

Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

The skeleton.dtsi file was removed in ARM64 for different reasons as
explained in commit ("3ebee5a2

 arm64: dts: kill skeleton.dtsi").

These also applies to ARM and it will also allow to get rid of the
following DTC warnings in the future:

"Node /memory has a reg or ranges property, but no unit name"

The disassembled DTB are almost the same besides an empty chosen
node being removed and nodes reordered, so it should not have
functional changes.

Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

The skeleton.dtsi file was removed in ARM64 for different reasons as
explained in commit ("3ebee5a2

 arm64: dts: kill skeleton.dtsi").

These also applies to ARM and it will also allow to get rid of the
following DTC warnings in the future:

"Node /memory has a reg or ranges property, but no unit name"

The disassembled DTB are almost the same besides an empty chosen
node being removed and nodes reordered, so it should not have
functional changes.

Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

The skeleton.dtsi file was removed in ARM64 for different reasons as
explained in commit ("3ebee5a2

 arm64: dts: kill skeleton.dtsi").

These also applies to ARM and it will also allow to get rid of the
following DTC warnings in the future:

"Node /memory has a reg or ranges property, but no unit name"

But these boards don't have a memory node defined, so removing the
skeleton.dtsi inclusion from omap3.dtsi will cause a change in the
compiled DTB. Add a dummy memory node so the compiled DTB doesn't
change if the skeleton.dtsi is removed from omap3.dtsi.

Eventually the correct starting addresses and sizes should be used
but I didn't find that information.

Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

The skeleton.dtsi file was removed in ARM64 for different reasons as
explained in commit ("3ebee5a2

 arm64: dts: kill skeleton.dtsi").

These also applies to ARM and it will also allow to get rid of the
following DTC warnings in the future:

"Node /memory has a reg or ranges property, but no unit name"

But the sl50 board doesn't have a, so removing the  skeleton.dtsi
inclusion from am33xx.dtsi will cause a change in the compiled DTB.

The board has 512 MiB of RAM and its starting address is 0x80000000,
so add a proper memory device node in the DTS.

Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Current clocks tree definition for CPSW/CPTS doesn't
correspond TRM for dra7/am57 SoCs.

CPTS: has to be sourced from gmac_rft_clk_mux clock
CPSW: DPLL_GMAC -> CLKOUT_M2 -> GMAC_250M_CLK -> 1/2 ->
      -> GMAC_MAIN_CLK (125 MHZ)

Hence, correct clock tree for GMAC_MAIN_CLK and use proper
clock for CPTS. This also require updating of CPTS clock
multiplier.

Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Reviewed-by: Mugunthan V N <mugunthanvnm@ti.com>
Acked-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

This commit fixes the clock data inside the DRA7xx clocks device tree
structure for the gmac_gmii_ref_clk_div clock. This clock is actually
the GMAC_MAIN_CLK and has nothing to do with the register at address
0x4a0093d0. If CLKSEL_REF bit 24 inside of CM_GMAC_GMAC_CLKCTRL, is
set to 1 in order to use the GMAC_RMII_CLK instead of the
GMAC_RMII_HS_CLK, the kernel generates a clock divider warning:
    WARNING: CPU: 0 PID: 0 at drivers/clk/clk-divider.c:129 clk_divider_recalc_rate+0xa8/0xe0()
    gmac_gmii_ref_clk_div: Zero divisor and CLK_DIVIDER_ALLOW_ZERO not set

By properly configuring the gmac_gmii_ref_clk_div (GMAC_MAIN_CLK) to
have the parent of dpll_gmac_m2_ck always divided by 2 the warning is
resolved and the clock tree is fixed up.

Additionally, a new clock called rmii_50mhz_clk_mux is defined that
does utilize CM_GMAC_GMAC_CLKCTRL[24] CLKSEL_REF to configure the
source clock for the RMII_50MHZ_CLK.

Cc: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: J.D. Schroeder <jay.schroeder@garmin.com>
Reviewed-by: Trenton Andres <trenton.andres@garmin.com>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Acked-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Since DRA7 has multiple PCIe Rootcomplex, add "linux,pci-domain"
property to assign a PCI domain number to each of the host
bridges.

Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

AM335x ICE board has a rotary-switch connected to PCA9536 I2C GPIO
expander. The position of the rotary-switch is reflected by status of
GPIO lines. Add gpio-decoder node to read these GPIO line status via
gpio-decoder driver and report it as an input event to the system.

Signed-off-by: Vignesh R <vigneshr@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Support is in the device tree, but they are not mentioned here.

Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Silicon limitation i845 documents how to cope with false
disconnection condition on USB2 PHY. Reference: AM572x
silicon errata document SPRZ429H, revised January 2016.

Using compatible "ti,dra7x-usb2" enables the recommended
software workaround for this issue. Use it for USB1 PHY.

The workaround is already in place for USB2 PHY.

Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

The wega board has a TLV320AIC3007 connected via McASP0. In the default
configuration, no external crystal is mounted. We run a system clock of
25 MHz, so we use the audio codec PLL for audio clock generation.

Signed-off-by: Stefan Müller-Klieser <s.mueller-klieser@phytec.de>
Reviewed-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

AM572x IDK has a Spansion s25fl256s1 QSPI flash on the EVM connected to
TI QSPI IP over CS0. Hence, add QSPI and flash slave DT nodes.

Signed-off-by: Vignesh R <vigneshr@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

According to AM572x DM SPRS953A, QSPI maximum bus speed can be 76.8MHz.
Therefore, increase the spi-max-frequency value of QSPI node to 76.8MHz
for DRA74 and DRA72 evm. This improves flash raw read speed by ~2MB/s.

Signed-off-by: Vignesh R <vigneshr@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

With the device tree parsing using the regulator framework
there is a no longer a need for separate compatibles for
individual regulator nodes. Hence removing them all.

Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

With the device tree parsing using the regulator framework
there is a no longer a need for separate compatibles for
individual regulator nodes. Hence removing them all.

Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>