net: phy: Create phy_supported_speeds function which lists speeds currently supported by a phydevice

phy_supported_speeds provides a means to get a list of all the speeds a
phy device currently supports.

Signed-off-by: Zach Brown <zach.brown@ni.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

During phy state machine state transitions some set of actions should
occur whenever the link state changes. These actions should be
encapsulated into a single function

This patch adds the phy_adjust_link function, which is called whenever
phydev->adjust_link would have been called before. Actions that should
occur whenever the phy link is adjusted can now be added to the
phy_adjust_link function.

Signed-off-by: Zach Brown <zach.brown@ni.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Adding led support for phy causes namespace conflicts for some
phy drivers.

The marvel skge driver declared an enum for representing the states of
Link LED Register. The enum contained constant LED_OFF which conflicted
with declartation found in linux/leds.h.
LED_OFF changed to LED_REG_OFF
Also changed LED_ON to LED_REG_ON to avoid possible future conflict and
for consistency.

Signed-off-by: Zach Brown <zach.brown@ni.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

David Ahern says:

====================
net: Fix netdev adjacency tracking

The netdev adjacency tracking is failing to create proper dependencies
for some topologies. For example this topology

        +--------+
        |  myvrf |
        +--------+
          |    |
          |  +---------+
          |  | macvlan |
          |  +---------+
          |    |
      +----------+
      |  bridge  |
      +----------+
          |
      +--------+
      | bond1  |
      +--------+
          |
      +--------+
      |  eth3  |
      +--------+

hits 1 of 2 problems depending on the order of enslavement. The base set of
commands for both cases:

    ip link add bond1 type bond
    ip link set bond1 up
    ip link set eth3 down
    ip link set eth3 master bond1
    ip link set eth3 up

    ip link add bridge type bridge
    ip link set bridge up
    ip link add macvlan link bridge type macvlan
    ip link set macvlan up

    ip link add myvrf type vrf table 1234
    ip link set myvrf up

    ip link set bridge master myvrf

Case 1 enslave macvlan to the vrf before enslaving the bond to the bridge:

    ip link set macvlan master myvrf
    ip link set bond1 master bridge

Attempts to delete the VRF:
    ip link delete myvrf

trigger the BUG in __netdev_adjacent_dev_remove:

[  587.405260] tried to remove device eth3 from myvrf
[  587.407269] ------------[ cut here ]------------
[  587.408918] kernel BUG at /home/dsa/kernel.git/net/core/dev.c:5661!
[  587.411113] invalid opcode: 0000 [#1] SMP
[  587.412454] Modules linked in: macvlan bridge stp llc bonding vrf
[  587.414765] CPU: 0 PID: 726 Comm: ip Not tainted 4.8.0+ #109
[  587.416766] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.7.5-20140531_083030-gandalf 04/01/2014
[  587.420241] task: ffff88013ab6eec0 task.stack: ffffc90000628000
[  587.422163] RIP: 0010:[<ffffffff813cef03>]  [<ffffffff813cef03>] __netdev_adjacent_dev_remove+0x40/0x12c
...
[  587.446053] Call Trace:
[  587.446424]  [<ffffffff813d1542>] __netdev_adjacent_dev_unlink+0x20/0x3c
[  587.447390]  [<ffffffff813d16a3>] netdev_upper_dev_unlink+0xfa/0x15e
[  587.448297]  [<ffffffffa00003a3>] vrf_del_slave+0x13/0x2a [vrf]
[  587.449153]  [<ffffffffa00004a4>] vrf_dev_uninit+0xea/0x114 [vrf]
[  587.450036]  [<ffffffff813d19b0>] rollback_registered_many+0x22b/0x2da
[  587.450974]  [<ffffffff813d1aac>] unregister_netdevice_many+0x17/0x48
[  587.451903]  [<ffffffff813de444>] rtnl_delete_link+0x3c/0x43
[  587.452719]  [<ffffffff813dedcd>] rtnl_dellink+0x180/0x194

When the BUG is converted to a WARN_ON it shows 4 missing adjacencies:
  eth3 - myvrf, mvrf - eth3, bond1 - myvrf and myvrf - bond1

All of those are because the __netdev_upper_dev_link function does not
properly link macvlan lower devices to myvrf when it is enslaved.

The second case just flips the ordering of the enslavements:
    ip link set bond1 master bridge
    ip link set macvlan master myvrf

Then run:
    ip link delete bond1
    ip link delete myvrf

The vrf delete command hangs because myvrf has a reference that has not
been released. In this case the removal code does not account for 2 paths
between eth3 and myvrf - one from bridge to vrf and the other through the
macvlan.

Rather than try to maintain a linked list of all upper and lower devices
per netdevice, only track the direct neighbors. The remaining stack can
be determined by recursively walking the neighbors.

The existing netdev_for_each_all_upper_dev_rcu,
netdev_for_each_all_lower_dev and netdev_for_each_all_lower_dev_rcu macros
are replaced with APIs that walk the upper and lower device lists. The
new APIs take a callback function and a data arg that is passed to the
callback for each device in the list. Drivers using the old macros are
converted in separate patches to make it easier on reviewers. It is an
API conversion only; no functional change is intended.

v3
- address Stephen's comment to simplify logic and remove typecasts

v2
- fixed bond0 references in cover-letter
- fixed definition of netdev_next_lower_dev_rcu to mirror the upper_dev
  version.
====================

Signed-off-by: David S. Miller <davem@davemloft.net>

Adjacency code only has debugs for the insert case. Add debugs for
the remove path and make both consistently worded to make it easier
to follow the insert and removal with reference counts.

In addition, change the BUG to a WARN_ON. A missing adjacency at
removal time is not cause for a panic.

Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Lower list should be empty just like upper.

Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Only direct adjacencies are maintained. All upper or lower devices can
be learned via the new walk API which recursively walks the adj_list for
upper devices or lower devices.

Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Convert rocker to the new dev walk API. This is just a code conversion;
no functional change is intended.

v2
- removed typecast of data

Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Convert mlxsw users to new dev walk API. This is just a code conversion;
no functional change is intended.

Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Convert ixgbe users to new dev walk API. This is just a code conversion;
no functional change is intended.

Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Convert ipoib_get_net_dev_match_addr to the new upper device walk API.
This is just a code conversion; no functional change is intended.

v2
- removed typecast of data

Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Convert rdma_is_upper_dev_rcu, handle_netdev_upper and
ipoib_get_net_dev_match_addr to the new upper device walk API.
This is just a code conversion; no functional change is intended.

v2
- removed typecast of data

Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Convert alb_send_learning_packets and bond_has_this_ip to use the new
netdev_walk_all_upper_dev_rcu API. In both cases this is just a code
conversion; no functional change is intended.

v2
- removed typecast of data and simplified bond_upper_dev_walk

Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch introduces netdev_walk_all_upper_dev_rcu,
netdev_walk_all_lower_dev and netdev_walk_all_lower_dev_rcu. These
functions recursively walk the adj_list of devices to determine all upper
and lower devices.

The functions take a callback function that is invoked for each device
in the list. If the callback returns non-0, the walk is terminated and
the functions return that code back to callers.

v3
- simplified netdev_has_upper_dev_all_rcu and __netdev_has_upper_dev and
  removed typecast as suggested by Stephen

v2
- fixed definition of netdev_next_lower_dev_rcu to mirror the upper_dev
  version.

Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Commit 93409033 ("net: Add netdev all_adj_list refcnt propagation to
fix panic") propagated the refnr to insert and remove functions tracking
the netdev adjacency graph. However, for the insert path the refnr can
only be 1. Accordingly, remove the refnr argument to make that clear.
ie., the refnr arg in 93409033

 was only needed for the remove path.

Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Daniel Borkmann says:

====================
Move to BPF selftests

This set improves the test_verifier and test_maps suite and moves
it over to a new BPF selftest directory, so we can keep improving
it under kernel selftest umbrella. This also integrates a test
script for checking test_bpf.ko under various JIT options.
====================

Signed-off-by: David S. Miller <davem@davemloft.net>

Add a start of a test suite for kernel selftests. This moves test_verifier
and test_maps over to tools/testing/selftests/bpf/ along with various
code improvements and also adds a script for invoking test_bpf module.
The test suite can simply be run via selftest framework, f.e.:

  # cd tools/testing/selftests/bpf/
  # make
  # make run_tests

Both test_verifier and test_maps were kind of misplaced in samples/bpf/
directory and we were looking into adding them to selftests for a while
now, so it can be picked up by kbuild bot et al and hopefully also get
more exposure and thus new test case additions.

Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add several spill/fill tests. Besides others, one that performs xadd
on the spilled register, one ldx/stx test where different types are
spilled from two branches and read out from common path. Verfier does
handle all correctly.

Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Jarod Wilson says:

====================
ethernet: use core min/max MTU checking

Now that the network stack core min/max MTU checking infrastructure is in
place, time to start making drivers use it. We'll start with the easiest
ones, the ethernet drivers, split roughly by vendor, with a catch-all
patch at the end.

For the most part, every patch does the same essential thing: removes the
MTU range checking from the drivers' ndo_change_mtu function, puts those
ranges into the core net_device min_mtu and max_mtu fields, and where
possible, removes ndo_change_mtu functions entirely.

These patches have all been built through the 0-day build infrastructure
provided by Intel, on top of net-next as of October 17.
====================

Signed-off-by: David S. Miller <davem@davemloft.net>

et131x: min_mtu 64, max_mtu 9216

altera_tse: min_mtu 64, max_mtu 1500

amd8111e: min_mtu 60, max_mtu 9000

bnad: min_mtu 46, max_mtu 9000

macb: min_mtu 68, max_mtu 1500 or 10240 depending on hardware capability

xgmac: min_mtu 46, max_mtu 9000

cxgb2: min_mtu 68, max_mtu 9582 (pm3393) or 9600 (vsc7326)

enic: min_mtu 68, max_mtu 9000

gianfar: min_mtu 50, max_mu 9586

hns_enet: min_mtu 68, max_mtu 9578 (v1) or 9706 (v2)

ksz884x: min_mtu 60, max_mtu 1894

myri10ge: min_mtu 68, max_mtu 9000

natsemi: min_mtu 64, max_mtu 2024

nfp: min_mtu 68, max_mtu hardware-specific

forcedeth: min_mtu 64, max_mtu 1500 or 9100, depending on hardware

pch_gbe: min_mtu 46, max_mtu 10300

pasemi_mac: min_mtu 64, max_mtu 9000

qcaspi: min_mtu 46, max_mtu 1500
- remove qcaspi_netdev_change_mtu as it is now redundant

rocker: min_mtu 68, max_mtu 9000

sxgbe: min_mtu 68, max_mtu 9000

stmmac: min_mtu 46, max_mtu depends on hardware

tehuti: min_mtu 60, max_mtu 16384
- driver had no max mtu checking, but product docs say 16k jumbo packets
  are supported by the hardware

netcp: min_mtu 68, max_mtu 9486
- remove netcp_ndo_change_mtu as it is now redundant

via-velocity: min_mtu 64, max_mtu 9000

octeon: min_mtu 46, max_mtu 65370

CC: netdev@vger.kernel.org
CC: Mark Einon <mark.einon@gmail.com>
CC: Vince Bridgers <vbridger@opensource.altera.com>
CC: Rasesh Mody <rasesh.mody@qlogic.com>
CC: Nicolas Ferre <nicolas.ferre@atmel.com>
CC: Santosh Raspatur <santosh@chelsio.com>
CC: Hariprasad S <hariprasad@chelsio.com>
CC:  Christian Benvenuti <benve@cisco.com>
CC: Sujith Sankar <ssujith@cisco.com>
CC: Govindarajulu Varadarajan <_govind@gmx.com>
CC: Neel Patel <neepatel@cisco.com>
CC: Claudiu Manoil <claudiu.manoil@freescale.com>
CC: Yisen Zhuang <yisen.zhuang@huawei.com>
CC: Salil Mehta <salil.mehta@huawei.com>
CC: Hyong-Youb Kim <hykim@myri.com>
CC: Jakub Kicinski <jakub.kicinski@netronome.com>
CC: Olof Johansson <olof@lixom.net>
CC: Jiri Pirko <jiri@resnulli.us>
CC: Byungho An <bh74.an@samsung.com>
CC: Girish K S <ks.giri@samsung.com>
CC: Vipul Pandya <vipul.pandya@samsung.com>
CC: Giuseppe Cavallaro <peppe.cavallaro@st.com>
CC: Alexandre Torgue <alexandre.torgue@st.com>
CC: Andy Gospodarek <andy@greyhouse.net>
CC: Wingman Kwok <w-kwok2@ti.com>
CC: Murali Karicheri <m-karicheri2@ti.com>
CC: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

gelic_net: min_mtu 64, max_mtu 1518
- remove gelic_net_change_mtu now that it is redundant

spidernet: min_Mtu 64, max_mtu 2294
- remove spiter_net_change_mtu now that it is redundant

CC: netdev@vger.kernel.org
CC: Geoff Levand <geoff@infradead.org>
CC: Ishizaki Kou <kou.ishizaki@toshiba.co.jp>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

tilegx: min_mtu 68, max_mtu 1500 or 9000, depending on modparam
- remove tile_net_change_mtu now that it is fully redundant

tilepro: min_mtu 68, max_mtu 1500
- hardware supports jumbo packets up to 10226, but it's not implemented or
  tested yet, according to code comments

CC: netdev@vger.kernel.org
CC: Chris Metcalf <cmetcalf@mellanox.com>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

ehea: min_mtu 68, max_mtu 9022
- remove ehea_change_mtu, it's now redundant

emac: min_mtu 46, max_mtu 1500 or whatever gets read from OF

CC: netdev@vger.kernel.org
CC: Douglas Miller <dougmill@linux.vnet.ibm.com>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

liquidio: min_mtu 68, max_mtu 16000

thunder: min_mtu 64, max_mtu 9200

CC: netdev@vger.kernel.org
CC: Sunil Goutham <sgoutham@cavium.com>
CC: Robert Richter <rric@kernel.org>
CC: Derek Chickles <derek.chickles@caviumnetworks.com>
CC: Satanand Burla <satananda.burla@caviumnetworks.com>
CC: Felix Manlunas <felix.manlunas@caviumnetworks.com>
CC: Raghu Vatsavayi <raghu.vatsavayi@caviumnetworks.com>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

s2io: min_mtu 46, max_mtu 9600

vxge: min_mtu 68, max_mtu 9600

CC: netdev@vger.kernel.org
CC: Jon Mason <jdmason@kudzu.us>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

dl2k: min_mtu 68, max_mtu 1536 or 8000, depending on hardware
- Removed change_mtu, does nothing productive anymore

sundance: min_mtu 68, max_mtu 8191

CC: netdev@vger.kernel.org
CC: Denis Kirjanov <kda@linux-powerpc.org>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

cassini: min_mtu 60, max_mtu 9000

niu: min_mtu 68, max_mtu 9216

sungem: min_mtu 68, max_mtu 1500 (comments say jumbo mode is broken)

sunvnet: min_mtu 68, max_mtu 65535
- removed sunvnet_change_mut_common as it does nothing now

CC: netdev@vger.kernel.org
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

8139cp: min_mtu 60, max_mtu 4096

8139too: min_mtu 68, max_mtu 1770

r8169: min_mtu 60, max_mtu depends on chipset, 1500 to 9k-ish

CC: netdev@vger.kernel.org
CC: Realtek linux nic maintainers <nic_swsd@realtek.com>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

qede: min_mtu 46, max_mtu 9600
- Put define for max in qede.h

qlcnic: min_mtu 68, max_mtu 9600

CC: netdev@vger.kernel.org
CC Dept-GELinuxNICDev@qlogic.com
CC: Yuval Mintz <Yuval.Mintz@qlogic.com>
CC: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

mlx4: min_mtu 46, max_mtu depends on hardware

mlx5: min_mtu 68, max_mtu depends on hardware

CC: netdev@vger.kernel.org
CC: Tariq Toukan <tariqt@mellanox.com>
CC: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

mvneta: min_mtu 68, max_mtu 9676
- mtu validation routine mostly did range check, merge back into
  mvneta_change_mtu for simplicity

mvpp2: min_mtu 68, max_mtu 9676
- mtu validation routine mostly did range check, merge back into
  mvpp2_change_mtu for simplicity

pxa168_eth: min_mtu 68, max_mtu 9500

skge: min_mtu 60, max_mtu 9000

sky2: min_mtu 68, max_mtu 1500 or 9000, depending on hw

CC: netdev@vger.kernel.org
CC: Mirko Lindner <mlindner@marvell.com>
CC: Stephen Hemminger <stephen@networkplumber.org>
CC: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

e100: min_mtu 68, max_mtu 1500
- remove e100_change_mtu entirely, is identical to old eth_change_mtu,
  and no longer serves a purpose. No need to set min_mtu or max_mtu
  explicitly, as ether_setup() will already set them to 68 and 1500.

e1000: min_mtu 46, max_mtu 16110

e1000e: min_mtu 68, max_mtu varies based on adapter

fm10k: min_mtu 68, max_mtu 15342
- remove fm10k_change_mtu entirely, does nothing now

i40e: min_mtu 68, max_mtu 9706

i40evf: min_mtu 68, max_mtu 9706

igb: min_mtu 68, max_mtu 9216
- There are two different "max" frame sizes claimed and both checked in
  the driver, the larger value wasn't relevant though, so I've set max_mtu
  to the smaller of the two values here to retain identical behavior.

igbvf: min_mtu 68, max_mtu 9216
- Same issue as igb duplicated

ixgb: min_mtu 68, max_mtu 16114
- Also remove pointless old == new check, as that's done in dev_set_mtu

ixgbe: min_mtu 68, max_mtu 9710

ixgbevf: min_mtu 68, max_mtu dependent on hardware/firmware
- Some hw can only handle up to max_mtu 1504 on a vf, others 9710

CC: netdev@vger.kernel.org
CC: intel-wired-lan@lists.osuosl.org
CC: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

tg3: min_mtu 60, max_mtu 9000/1500

bnxt: min_mtu 60, max_mtu 9000

bnx2x: min_mtu 46, max_mtu 9600
- Fix up ETH_OVREHEAD -> ETH_OVERHEAD while we're in here, remove
  duplicated defines from bnx2x_link.c.

bnx2: min_mtu 46, max_mtu 9000
- Use more standard ETH_* defines while we're at it.

bcm63xx_enet: min_mtu 46, max_mtu 2028
- compute_hw_mtu was made largely pointless, and thus merged back into
  bcm_enet_change_mtu.

b44: min_mtu 60, max_mtu 1500

CC: netdev@vger.kernel.org
CC: Michael Chan <michael.chan@broadcom.com>
CC: Sony Chacko <sony.chacko@qlogic.com>
CC: Ariel Elior <ariel.elior@qlogic.com>
CC: Dept-HSGLinuxNICDev@qlogic.com
CC: Siva Reddy Kallam <siva.kallam@broadcom.com>
CC: Prashant Sreedharan <prashant@broadcom.com>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

atl2: min_mtu 40, max_mtu 1504

- Remove a few redundant defines that already have equivalents in
  if_ether.h.

atl1: min_mtu 42, max_mtu 10218

atl1e: min_mtu 42, max_mtu 8170

atl1c: min_mtu 42, max_mtu 6122/1500

- GbE hardware gets a max_mtu of 6122, slower hardware gets 1500.

alx: min_mtu 34, max_mtu 9256

- Not so sure that minimum MTU number is really what was intended, but
  that's what the math actually makes it out to be, due to max_frame
  manipulations and comparison in alx_change_mtu, rather than just
  comparing new_mtu. (I think 68 was the intended min_mtu value).

CC: netdev@vger.kernel.org
CC: Jay Cliburn <jcliburn@gmail.com>
CC: Chris Snook <chris.snook@gmail.com>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Mugunthan V N says:

====================
add support for impedance control for TI dp83867 phy and fix 2nd ethernet on dra72 rev C evm

Add support for configurable impedance control for TI dp83867
phy via devicetree. More documentation in [1].
CPSW second ethernet is not working, fix it by enabling
impedance configuration on the phy.

Verified the patch on DRA72 Rev C evm, logs at [2]. Also pushed
a branch [3] for others to test.

Changes from v3:
* Fixup change log text and no code changes.

Changes from v2:
* Fixed a typo in dts and driver.

Changes from initial version:
* As per Sekhar's comment, instead of passing impedance values,
  change to max and min impedance from DT
* Adopted phy_read_mmd_indirect() to cunnrent implementation.
* Corrected the phy delay timings to the optimal value.

[1] - http://www.ti.com/lit/ds/symlink/dp83867ir.pdf
[2] - http://pastebin.ubuntu.com/23343139/
[3] - git://git.ti.com/~mugunthanvnm/ti-linux-kernel/linux.git

 dp83867-v4
====================

Signed-off-by: David S. Miller <davem@davemloft.net>

The current delay settings of the phy are not the optimal value,
fix it with correct values.

Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The default impedance settings of the phy is not the optimal
value, due to this the second ethernet is not working. Fix it
with correct values which makes the second ethernet port to work.

Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add support for programmable MAC impedance configuration

Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add documention of ti,min-output-impedance and ti,max-output-impedance
which can be used to correct MAC impedance mismatch using phy extended
registers.

Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

args.u.name_type is of type unsigned int and is always >= 0.

This fixes the following GCC warning:

  net/8021q/vlan.c: In function ‘vlan_ioctl_handler’:
  net/8021q/vlan.c:574:14: warning: comparison of unsigned expression >= 0 is always true [-Wtype-limits]

Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>