commit b9f47a3a (tcp_cubic: limit delayed_ack ratio to prevent
divide error) try to prevent divide error, but there is still a little
chance that delayed_ack can reach zero. In case the param cnt get
negative value, then ratio+cnt would overflow and may happen to be zero.
As a result, min(ratio, ACK_RATIO_LIMIT) will calculate to be zero.

In some old kernels, such as 2.6.32, there is a bug that would
pass negative param, which then ultimately leads to this divide error.

commit 5b35e1e6

 (tcp: fix tcp_trim_head() to adjust segment count
with skb MSS) fixed the negative param issue. However,
it's safe that we fix the range of delayed_ack as well,
to make sure we do not hit a divide by zero.

CC: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: Liu Yu <allanyuliu@tencent.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The AND instruction is erroneously using the X register instead
of the K register.

Signed-off-by: Brendan Hickey <bhickey@google.com>
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This reverts commit 12a2856b

.
The commit above doesn't appear to be necessary any more as the
checksums appear to be correctly computed/validated.

Additionally the above commit breaks kvm configurations where
one VM is using a device that support checksum offload (virtio) and
the other VM does not.
In this case, packets leaving virtio device will have CHECKSUM_PARTIAL
set.  The packets is forwarded to a macvtap that has offload features
turned off.  Since we use CHECKSUM_UNNECESSARY, the host does does not
update the checksum and thus a bad checksum is passed up to
the guest.

CC: Daniel Lezcano <daniel.lezcano@free.fr>
CC: Patrick McHardy <kaber@trash.net>
CC: Andrian Nord <nightnord@gmail.com>
CC: Eric Dumazet <eric.dumazet@gmail.com>
CC: Michael S. Tsirkin <mst@redhat.com>
CC: Jason Wang <jasowang@redhat.com>
Signed-off-by: Vlad Yasevich <vyasevic@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The following is a problematic configuration:

 VM1: virtio-net device connected to macvtap0@eth0
 VM2: e1000 device connect to macvtap1@eth0

The problem is is that virtio-net supports checksum offloading
and thus sends the packets to the host with CHECKSUM_PARTIAL set.
On the other hand, e1000 does not support any acceleration.

For small TCP packets (and this includes the 3-way handshake),
e1000 ends up receiving packets that only have a partial checksum
set.  This causes TCP to fail checksum validation and to drop
packets.  As a result tcp connections can not be established.

Commit 3e4f8b78


	macvtap: Perform GSO on forwarding path.
fixes this issue for large packets wthat will end up undergoing GSO.
This commit adds a check for the non-GSO case and attempts to
compute the checksum for partially checksummed packets in the
non-GSO case.

CC: Daniel Lezcano <daniel.lezcano@free.fr>
CC: Patrick McHardy <kaber@trash.net>
CC: Andrian Nord <nightnord@gmail.com>
CC: Eric Dumazet <eric.dumazet@gmail.com>
CC: Michael S. Tsirkin <mst@redhat.com>
CC: Jason Wang <jasowang@redhat.com>
Signed-off-by: Vlad Yasevich <vyasevic@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Both TLP and Fast Open call __tcp_retransmit_skb() instead of
tcp_retransmit_skb() to avoid changing tp->retrans_out.

This has the side effect of missing SNMP counters increments as well
as tcp_info tcpi_total_retrans updates.

Fix this by moving the stats increments of into __tcp_retransmit_skb()

Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Nandita Dukkipati <nanditad@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch adds set_rx_int_on_com function for interrupt when
dma is completed.

Signed-off-by: Byungho An <bh74.an@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch adds rxqueue enable function according to number of rxqueue
and adds rxqueue disable function for removing.

Signed-off-by: Byungho An <bh74.an@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch moves sw reset to probe function because
sw reset is needed early stage before open function.

Signed-off-by: Byungho An <bh74.an@samsung.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add handling for " 8 GT/s" in print_port_info().

Signed-off-by: Roland Dreier <roland@purestorage.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This fixes the following sparse warnings:

drivers/net/ethernet/altera/altera_msgdma.c:23:5: warning: symbol 'msgdma_initialize' was not declared. Should it be static?
drivers/net/ethernet/altera/altera_msgdma.c:28:6: warning: symbol 'msgdma_uninitialize' was not declared. Should it be static?
drivers/net/ethernet/altera/altera_msgdma.c:32:6: warning: symbol 'msgdma_reset' was not declared. Should it be static?
drivers/net/ethernet/altera/altera_msgdma.c:77:6: warning: symbol 'msgdma_disable_rxirq' was not declared. Should it be static?
drivers/net/ethernet/altera/altera_msgdma.c:83:6: warning: symbol 'msgdma_enable_rxirq' was not declared. Should it be static?
drivers/net/ethernet/altera/altera_msgdma.c:89:6: warning: symbol 'msgdma_disable_txirq' was not declared. Should it be static?
drivers/net/ethernet/altera/altera_msgdma.c:95:6: warning: symbol 'msgdma_enable_txirq' was not declared. Should it be static?
drivers/net/ethernet/altera/altera_msgdma.c:101:6: warning: symbol 'msgdma_clear_rxirq' was not declared. Should it be static?
drivers/net/ethernet/altera/altera_msgdma.c:107:6: warning: symbol 'msgdma_clear_txirq' was not declared. Should it be static?
drivers/net/ethernet/altera/altera_msgdma.c:114:5: warning: symbol 'msgdma_tx_buffer' was not declared. Should it be static?
drivers/net/ethernet/altera/altera_msgdma.c:129:5: warning: symbol 'msgdma_tx_completions' was not declared. Should it be static?
drivers/net/ethernet/altera/altera_msgdma.c:154:5: warning: symbol 'msgdma_add_rx_desc' was not declared. Should it be static?
drivers/net/ethernet/altera/altera_msgdma.c:181:5: warning: symbol 'msgdma_rx_status' was not declared. Should it be static?

Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Acked-by: Vince Bridgers <vbridgers2013@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

sgdma_descrip is a function name as well as the name of a struct. In
sgdma_initialize(), we should initialize the descriptor length field
with the actual length of a descriptor not with the size of the
function. In order to prevent such things from happening in the future,
rename the function to sgdma_setup_descrip().

Found by sparse which yields the following warning:

drivers/net/ethernet/altera/altera_sgdma.c:74:30: warning: expression using sizeof on a function

Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

Fix format string mismatch in bonding_show_min_links().

Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

To properly match iif in ip rules we have to provide
LOOPBACK_IFINDEX in flowi6_iif, not 0. Some ip6mr_fib_lookup
and fib6_rule_lookup callers need such fix.

Signed-off-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: David S. Miller <davem@davemloft.net>

Don't transition to the PF state on every strike after 'Path.Max.Retrans'.
Per draft-ietf-tsvwg-sctp-failover-03 Section 5.1.6:

   Additional (PMR - PFMR) consecutive timeouts on a PF destination
   confirm the path failure, upon which the destination transitions to the
   Inactive state.  As described in [RFC4960], the sender (i) SHOULD notify
   ULP about this state transition, and (ii) transmit heartbeats to the
   Inactive destination at a lower frequency as described in Section 8.3 of
   [RFC4960].

This also prevents sending SCTP_ADDR_UNREACHABLE to the user as the state
bounces between SCTP_INACTIVE and SCTP_PF for each subsequent strike.

Signed-off-by: Karl Heiss <kheiss@gmail.com>
Acked-by: Vlad Yasevich <vyasevich@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

With commit cc9fa74e ("slip/slcan: added locking in wakeup function") a
formerly missing locking was added to slip.c and slcan.c by Andre Naujoks.

Alexander Stein contributed the fix 367525c8

 ("can: slcan: Fix spinlock
variant") as the kernel lock debugging advised to use spin_lock_bh() instead
of just using spin_lock().

This fix has to be applied to the same code section in slip.c for the same
reason too.

Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

Bjørn Mork says:

====================
qmi_wwan: adding a few new devices

Adding some new and some old QMI devices.  A similar series for
usb-serial support will be posted as well.

These new device ID patches should also go to all maintained stable kernels
where they apply. I believe that should be stable-3.10 and newer.
====================

Signed-off-by: David S. Miller <davem@davemloft.net>

Dan writes:

"The Dell drivers use the same configuration for PIDs:

81A2: Dell Wireless 5806 Gobi(TM) 4G LTE Mobile Broadband Card
81A3: Dell Wireless 5570 HSPA+ (42Mbps) Mobile Broadband Card
81A4: Dell Wireless 5570e HSPA+ (42Mbps) Mobile Broadband Card
81A8: Dell Wireless 5808 Gobi(TM) 4G LTE Mobile Broadband Card
81A9: Dell Wireless 5808e Gobi(TM) 4G LTE Mobile Broadband Card

These devices are all clearly Sierra devices, but are also definitely
Gobi-based.  The A8 might be the MC7700/7710 and A9 is likely a MC7750.

>From DellGobi5kSetup.exe from the Dell drivers:

usbif0: serial/firmware loader?
usbif2: nmea
usbif3: modem/ppp
usbif8: net/QMI"

Reported-by: AceLan Kao <acelan.kao@canonical.com>
Reported-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>

A number of older CMOTech modems are based on Qualcomm
chips and exporting a QMI/wwan function.

Reported-by: Lars Melin <larsm17@gmail.com>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>

Device interface layout:
0: ff/ff/ff - serial
1: ff/00/00 - serial AT+PPP
2: ff/ff/ff - QMI/wwan
3: 08/06/50 - storage

Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>

Device interface layout:
0: ff/ff/ff - serial
1: ff/ff/ff - serial AT+PPP
2: 08/06/50 - storage
3: ff/ff/ff - serial
4: ff/ff/ff - QMI/wwan

Reported-by: Julio Araujo <julio.araujo@wllctel.com.br>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>

commit 813b3b5d (ipv4: Use caller's on-stack flowi as-is
in output route lookups.) introduces another regression which
is very similar to the problem of commit e6b45241

 (ipv4: reset
flowi parameters on route connect) wants to fix:
Before we call ip_route_output_key() in sctp_v4_get_dst() to
get a dst that matches a bind address as the source address,
we have already called this function previously and the flowi
parameters have been initialized including flowi4_oif, so when
we call this function again, the process in __ip_route_output_key()
will be different because of the setting of flowi4_oif, and we'll
get a networking device which corresponds to the inputted flowi4_oif
as the output device, this is wrong because we'll never hit this
place if the previously returned source address of dst match one
of the bound addresses.

To reproduce this problem, a vlan setting is enough:
  # ifconfig eth0 up
  # route del default
  # vconfig add eth0 2
  # vconfig add eth0 3
  # ifconfig eth0.2 10.0.1.14 netmask 255.255.255.0
  # route add default gw 10.0.1.254 dev eth0.2
  # ifconfig eth0.3 10.0.0.14 netmask 255.255.255.0
  # ip rule add from 10.0.0.14 table 4
  # ip route add table 4 default via 10.0.0.254 src 10.0.0.14 dev eth0.3
  # sctp_darn -H 10.0.0.14 -P 36422 -h 10.1.4.134 -p 36422 -s -I
You'll detect that all the flow are routed to eth0.2(10.0.1.254).

Signed-off-by: Xufeng Zhang <xufeng.zhang@windriver.com>
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Acked-by: Vlad Yasevich <vyasevich@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This adds ability for the arc_emac to really handle its supplying clock.
To get the needed clock-frequency either a real clock or the previous
clock-frequency property must be provided.

Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: Max Schwarz <max.schwarz@online.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

The probe function at the moment only frees the netdev but does not disconnect
the phy or removes the mdio bus it registered.

Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

When bridge device is created with IFLA_ADDRESS, we are not calling
br_stp_change_bridge_id(), which leads to incorrect local fdb
management and bridge id calculation, and prevents us from receiving
frames on the bridge device.

Reported-by: Tom Gundersen <teg@jklm.no>
Signed-off-by: Toshiaki Makita <makita.toshiaki@lab.ntt.co.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch fixes the PTP Tx timestamp interrupt handler. The original
code misinterpreted the interrupt handler design. We were clearing the
ena_mask bit for the Timesync interrupts. This is done to indicate that
the interrupt will be handled in a scheduled work item (instead of
immediately) and that work item is responsible for re-enabling the
interrupts. However, the Tx timestamp was being handled immediately and
nothing was ever re-enabling it. This resulted in a single interrupt
working for the life of the driver.

This patch fixes the issue by instead clearing the bit from icr0 which
is used to indicate that the interrupt was immediately handled and can
be re-enabled right away. This patch also clears up a related issue due
to writing the PRTTSYN_STAT_0 register, which was unintentionally
clearing the cause bits for Timesync interrupts.

Change-ID: I057bd70d53c302f60fab78246989cbdfa469d83b
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Acked-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Acked-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Marc Kleine-Budde says:

====================
this is a pull request for net/master, for the v3.15 release cycle, consisting
of 26 patches.

Thomas Gleixner contributes 21 patches for the c_can driver, which address
several shortcomings in the driver like hardware initialisation, concurrency,
message ordering and poor performance. Two patches Oliver Hartkopp, one adds a
missing lock to the sja1000_isa driver, the other one fixes the return value in
the generic bit time configuration function. And finally a patch by Alexander
Stein, that fixes the slcan driver to use the correct spinlock variant.

To make it 26 patches, Wolfgang Grandegger patch for the c_can_pci
driver, which enables the bus master only for MSI and a patch by
Wolfram Sang, which converts the 'instance' in the c_can driver to the
proper type.
====================

Signed-off-by: David S. Miller <davem@davemloft.net>

Vince Bridgers says:

====================
This series of patches addresses a handful of issues found in testing
and reported by users of the Altera Triple Speed Ethernet soft IP.

The patches address the following issues (in summary)

1) The SGDMA soft IP was found to incorrectly process receive packets
   when the target physical address of the receive buffer was on
   a boundary that's not 32-bit aligned. One of the patches addresses
   this issue.
2) The pause quanta was not being set by the driver, one patch of this
   series sets the pause quanta to the IEEE defined default value
   since the hardware reset value is 0.
3) An issue in a error recovery path of the probe routine caused a
   kernel panic in the event a phy was probed and could not be found.
   A patch addresses this issue.
4) A change was made to the driver name for Ethtool support, and
   comments added to support an addition to Ethtool to support
   the Altera Triple Speed Ethernet controller.
====================

Signed-off-by: David S. Miller <davem@davemloft.net>

This patch changes the name used by Ethtool to something more
conventional in preparation for TSE Ethtool register dump
support to be added in the near future.

Signed-off-by: Vince Bridgers <vbridgers2013@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch addresses a fault in the error recovery path of the probe
routine where the netdev structure was not being unregistered properly
leading to a panic only when the phy probe failed.

Abbreviated panic stack seen is as follows:

(free_netdev+0xXX) from (altera_tse_probe+0xXX)
(altera_tse_probe+0xXX) from (platform_drv_probe+0xXX)
(platform_drv_probe+0xXX) from (driver_probe_device+0xXX)
(driver_probe_device+0xXX) from (__driver_attach+0xXX)
(__driver_attach+0xXX) from (bus_for_each_dev+0xXX)
(bus_for_each_dev+0xXX) from (driver_attach+0xXX)
(driver_attach+0xXX) from (bus_add_driver+0xXX)
(bus_add_driver+0xXX) from (driver_register+0xXX)
(driver_register+0xXX) from (__platform_driver_register+0xXX)
(__platform_driver_register+0xXX) from (altera_tse_driver_init+0xXX)
(altera_tse_driver_init+0xXX) from (do_one_initcall+0xXX)
(do_one_initcall+0xXX) from (kernel_init_freeable+0xXX)
(kernel_init_freeable+0xXX) from (kernel_init+0xXX)
(kernel_init+0xXX) from (ret_from_fork+0xXX)

Signed-off-by: Vince Bridgers <vbridgers2013@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch initializes the pause quanta set for transmitted pause frames
to the IEEE specified default of 0xffff.

Signed-off-by: Vince Bridgers <vbridgers2013@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch works around a recently discovered unaligned receive dma problem
with the Altera SGMDA. The Altera SGDMA component cannot be configured to
DMA data to unaligned addresses for receive packet operations from the
Triple Speed Ethernet component because of a potential data transfer
corruption that can occur. This patch addresses this issue by
utilizing the shift 16 bits feature of the Altera Triple Speed Ethernet
component and modifying the receive buffer physical addresses accordingly
such that the target receive DMA address is always aligned on a 32-bit
boundary.

Signed-off-by: Vince Bridgers <vbridgers2013@gmail.com>
Tested-by: Matthew Gerlach <mgerlach@altera.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Yuval Mintz says:

====================
bnx2x: SRIOV bug fixes

This series contains 3 SRIOV bug fixes, 2 of which are regressions starting
with commit 2dc33bbc

 "bnx2x: Remove the sriov VFOP mechanism".
====================

Signed-off-by: David S. Miller <davem@davemloft.net>

Commit 2dc33bbc

 "bnx2x: Remove the sriov VFOP mechanism" caused a regression,
preventing VFs from configuring multicast filters.

Signed-off-by: Naredner Kumar <narender.kumar@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Starting with commit 2dc33bbc

 "bnx2x: Remove the sriov VFOP mechanism",
the bnx2x started enforcing vlan credits for all vlan configurations.
This exposed 2 issues:
  - Vlan credits are not returned once a VF is removed; this causes a leak
    of credits, and eventually will lead to VFs with no vlan credits.
  - A vlan credit must be set aside for the Hypervisor to use, and should
    not be visible to the VF.

Although linux VFs at the moment do not support vlan configuration [from the
VF side] which causes them to be resilient to this sort of issue, Windows VF
over linux hypervisors might fail to load as the vlan credits become depleted.

Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When removing a VF interface, the driver fails to release that VF's mailbox
and bulletin board allocated memory.

Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When the ipv6 fib changes during a table dump, the walk is
restarted and the number of nodes dumped are skipped. But the existing
code doesn't advance to the next node after a node is skipped. This can
cause the dump to loop or produce lots of duplicates when the fib
is modified during the dump.

This change advances the walk to the next node if the current node is
skipped after a restart.

Signed-off-by: Kumar Sundararajan <kumar@fb.com>
Signed-off-by: Chris Mason <clm@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>