We need to free the ld_active list head before jumping into the callback
routine. Otherwise the callback could run into issue_pending and change
our ld_active list head we just going to free. This will run the channel
list into an currupted and undefined state.

Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>

The tasklet and irqhandler are using spin_lock while other routines are
using spin_lock_irqsave/restore. This leads to lockdep issues as
described bellow. This patch is changing the code to use
spinlock_irq_save/restore in both code pathes.

As imxdma_xfer_desc always gets called with spin_lock_irqsave lock held,
this patch also removes the spare call inside the routine to avoid
double locking.

[  403.358162] =================================
[  403.362549] [ INFO: inconsistent lock state ]
[  403.366945] 3.10.0-20130823+ #904 Not tainted
[  403.371331] ---------------------------------
[  403.375721] inconsistent {IN-HARDIRQ-W} -> {HARDIRQ-ON-W} usage.
[  403.381769] swapper/0 [HC0[0]:SC1[1]:HE1:SE0] takes:
[  403.386762]  (&(&imxdma->lock)->rlock){?.-...}, at: [<c019d77c>] imxdma_tasklet+0x20/0x134
[  403.395201] {IN-HARDIRQ-W} state was registered at:
[  403.400108]   [<c004b264>] mark_lock+0x2a0/0x6b4
[  403.404798]   [<c004d7c8>] __lock_acquire+0x650/0x1a64
[  403.410004]   [<c004f15c>] lock_acquire+0x94/0xa8
[  403.414773]   [<c02f74e4>] _raw_spin_lock+0x54/0x8c
[  403.419720]   [<c019d094>] dma_irq_handler+0x78/0x254
[  403.424845]   [<c0061124>] handle_irq_event_percpu+0x38/0x1b4
[  403.430670]   [<c00612e4>] handle_irq_event+0x44/0x64
[  403.435789]   [<c0063a70>] handle_level_irq+0xd8/0xf0
[  403.440903]   [<c0060a20>] generic_handle_irq+0x28/0x38
[  403.446194]   [<c0009cc4>] handle_IRQ+0x68/0x8c
[  403.450789]   [<c0008714>] avic_handle_irq+0x3c/0x48
[  403.455811]   [<c0008f84>] __irq_svc+0x44/0x74
[  403.460314]   [<c0040b04>] cpu_startup_entry+0x88/0xf4
[  403.465525]   [<c02f00d0>] rest_init+0xb8/0xe0
[  403.470045]   [<c03e07dc>] start_kernel+0x28c/0x2d4
[  403.474986]   [<a0008040>] 0xa0008040
[  403.478709] irq event stamp: 50854
[  403.482140] hardirqs last  enabled at (50854): [<c001c6b8>] tasklet_action+0x38/0xdc
[  403.489954] hardirqs last disabled at (50853): [<c001c6a0>] tasklet_action+0x20/0xdc
[  403.497761] softirqs last  enabled at (50850): [<c001bc64>] _local_bh_enable+0x14/0x18
[  403.505741] softirqs last disabled at (50851): [<c001c268>] irq_exit+0x88/0xdc
[  403.513026]
[  403.513026] other info that might help us debug this:
[  403.519593]  Possible unsafe locking scenario:
[  403.519593]
[  403.525548]        CPU0
[  403.528020]        ----
[  403.530491]   lock(&(&imxdma->lock)->rlock);
[  403.534828]   <Interrupt>
[  403.537474]     lock(&(&imxdma->lock)->rlock);
[  403.541983]
[  403.541983]  *** DEADLOCK ***
[  403.541983]
[  403.547951] no locks held by swapper/0.
[  403.551813]
[  403.551813] stack backtrace:
[  403.556222] CPU: 0 PID: 0 Comm: swapper Not tainted 3.10.0-20130823+ #904
[  403.563039] Backtrace:
[  403.565581] [<c000b98c>] (dump_backtrace+0x0/0x10c) from [<c000bb28>] (show_stack+0x18/0x1c)
[  403.574054]  r6:00000000 r5:c05c51d8 r4:c040bd58 r3:00200000
[  403.579872] [<c000bb10>] (show_stack+0x0/0x1c) from [<c02f398c>] (dump_stack+0x20/0x28)
[  403.587955] [<c02f396c>] (dump_stack+0x0/0x28) from [<c02f29c8>] (print_usage_bug.part.28+0x224/0x28c)
[  403.597340] [<c02f27a4>] (print_usage_bug.part.28+0x0/0x28c) from [<c004b404>] (mark_lock+0x440/0x6b4)
[  403.606682]  r8:c004a41c r7:00000000 r6:c040bd58 r5:c040c040 r4:00000002
[  403.613566] [<c004afc4>] (mark_lock+0x0/0x6b4) from [<c004d844>] (__lock_acquire+0x6cc/0x1a64)
[  403.622244] [<c004d178>] (__lock_acquire+0x0/0x1a64) from [<c004f15c>] (lock_acquire+0x94/0xa8)
[  403.631010] [<c004f0c8>] (lock_acquire+0x0/0xa8) from [<c02f74e4>] (_raw_spin_lock+0x54/0x8c)
[  403.639614] [<c02f7490>] (_raw_spin_lock+0x0/0x8c) from [<c019d77c>] (imxdma_tasklet+0x20/0x134)
[  403.648434]  r6:c3847010 r5:c040e890 r4:c38470d4
[  403.653194] [<c019d75c>] (imxdma_tasklet+0x0/0x134) from [<c001c70c>] (tasklet_action+0x8c/0xdc)
[  403.662013]  r8:c0599160 r7:00000000 r6:00000000 r5:c040e890 r4:c3847114 r3:c019d75c
[  403.670042] [<c001c680>] (tasklet_action+0x0/0xdc) from [<c001bd4c>] (__do_softirq+0xe4/0x1f0)
[  403.678687]  r7:00000101 r6:c0402000 r5:c059919c r4:00000001
[  403.684498] [<c001bc68>] (__do_softirq+0x0/0x1f0) from [<c001c268>] (irq_exit+0x88/0xdc)
[  403.692652] [<c001c1e0>] (irq_exit+0x0/0xdc) from [<c0009cc8>] (handle_IRQ+0x6c/0x8c)
[  403.700514]  r4:00000030 r3:00000110
[  403.704192] [<c0009c5c>] (handle_IRQ+0x0/0x8c) from [<c0008714>] (avic_handle_irq+0x3c/0x48)
[  403.712664]  r5:c0403f28 r4:c0593ebc
[  403.716343] [<c00086d8>] (avic_handle_irq+0x0/0x48) from [<c0008f84>] (__irq_svc+0x44/0x74)
[  403.724733] Exception stack(0xc0403f28 to 0xc0403f70)
[  403.729841] 3f20:                   00000001 00000004 00000000 20000013 c0402000 c04104a8
[  403.738078] 3f40: 00000002 c0b69620 a0004000 41069264 a03fb5f4 c0403f7c c0403f40 c0403f70
[  403.746301] 3f60: c004b92c c0009e74 20000013 ffffffff
[  403.751383]  r6:ffffffff r5:20000013 r4:c0009e74 r3:c004b92c
[  403.757210] [<c0009e30>] (arch_cpu_idle+0x0/0x4c) from [<c0040b04>] (cpu_startup_entry+0x88/0xf4)
[  403.766161] [<c0040a7c>] (cpu_startup_entry+0x0/0xf4) from [<c02f00d0>] (rest_init+0xb8/0xe0)
[  403.774753] [<c02f0018>] (rest_init+0x0/0xe0) from [<c03e07dc>] (start_kernel+0x28c/0x2d4)
[  403.783051]  r6:c03fc484 r5:ffffffff r4:c040a0e0
[  403.787797] [<c03e0550>] (start_kernel+0x0/0x2d4) from [<a0008040>] (0xa0008040)

Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>

When perparing cyclic_dma buffers by the sound layer, it will dump the
following lockdep trace. The leading snd_pcm_action_single get called
with read_lock_irq called. To fix this, we change the kcalloc call from
GFP_KERNEL to GFP_ATOMIC.

WARNING: at kernel/lockdep.c:2740 lockdep_trace_alloc+0xcc/0x114()
DEBUG_LOCKS_WARN_ON(irqs_disabled_flags(flags))
Modules linked in:
CPU: 0 PID: 832 Comm: aplay Not tainted 3.11.0-20130823+ #903
Backtrace:
[<c000b98c>] (dump_backtrace+0x0/0x10c) from [<c000bb28>] (show_stack+0x18/0x1c)
 r6:c004c090 r5:00000009 r4:c2e0bd18 r3:00404000
[<c000bb10>] (show_stack+0x0/0x1c) from [<c02f397c>] (dump_stack+0x20/0x28)
[<c02f395c>] (dump_stack+0x0/0x28) from [<c001531c>] (warn_slowpath_common+0x54/0x70)
[<c00152c8>] (warn_slowpath_common+0x0/0x70) from [<c00153dc>] (warn_slowpath_fmt+0x38/0x40)
 r8:00004000 r7:a3b90000 r6:000080d0 r5:60000093 r4:c2e0a000 r3:00000009
[<c00153a4>] (warn_slowpath_fmt+0x0/0x40) from [<c004c090>] (lockdep_trace_alloc+0xcc/0x114)
 r3:c03955d8 r2:c03907db
[<c004bfc4>] (lockdep_trace_alloc+0x0/0x114) from [<c008f16c>] (__kmalloc+0x34/0x118)
 r6:000080d0 r5:c3800120 r4:000080d0 r3:c040a0f8
[<c008f138>] (__kmalloc+0x0/0x118) from [<c019c95c>] (imxdma_prep_dma_cyclic+0x64/0x168)
 r7:a3b90000 r6:00000004 r5:c39d8420 r4:c3847150
[<c019c8f8>] (imxdma_prep_dma_cyclic+0x0/0x168) from [<c024618c>] (snd_dmaengine_pcm_trigger+0xa8/0x160)
[<c02460e4>] (snd_dmaengine_pcm_trigger+0x0/0x160) from [<c0241fa8>] (soc_pcm_trigger+0x90/0xb4)
 r8:c058c7b0 r7:c3b8140c r6:c39da560 r5:00000001 r4:c3b81000
[<c0241f18>] (soc_pcm_trigger+0x0/0xb4) from [<c022ece4>] (snd_pcm_do_start+0x2c/0x38)
 r7:00000000 r6:00000003 r5:c058c7b0 r4:c3b81000
[<c022ecb8>] (snd_pcm_do_start+0x0/0x38) from [<c022e958>] (snd_pcm_action_single+0x40/0x6c)
[<c022e918>] (snd_pcm_action_single+0x0/0x6c) from [<c022ea64>] (snd_pcm_action_lock_irq+0x7c/0x9c)
 r7:00000003 r6:c3b810f0 r5:c3b810f0 r4:c3b81000
[<c022e9e8>] (snd_pcm_action_lock_irq+0x0/0x9c) from [<c023009c>] (snd_pcm_common_ioctl1+0x7f8/0xfd0)
 r8:c3b7f888 r7:005407b8 r6:c2c991c0 r5:c3b81000 r4:c3b81000 r3:00004142
[<c022f8a4>] (snd_pcm_common_ioctl1+0x0/0xfd0) from [<c023117c>] (snd_pcm_playback_ioctl1+0x464/0x488)
[<c0230d18>] (snd_pcm_playback_ioctl1+0x0/0x488) from [<c02311d4>] (snd_pcm_playback_ioctl+0x34/0x40)
 r8:c3b7f888 r7:00004142 r6:00000004 r5:c2c991c0 r4:005407b8
[<c02311a0>] (snd_pcm_playback_ioctl+0x0/0x40) from [<c00a14a4>] (vfs_ioctl+0x30/0x44)
[<c00a1474>] (vfs_ioctl+0x0/0x44) from [<c00a1fe8>] (do_vfs_ioctl+0x55c/0x5c0)
[<c00a1a8c>] (do_vfs_ioctl+0x0/0x5c0) from [<c00a208c>] (SyS_ioctl+0x40/0x68)
[<c00a204c>] (SyS_ioctl+0x0/0x68) from [<c0009380>] (ret_fast_syscall+0x0/0x44)
 r8:c0009544 r7:00000036 r6:bedeaa58 r5:00000000 r4:000000c0

Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>

The TI_EDMA driver unconditionally calls functions provided by the
TI_PRIV_EDMA code, but it doesn't force that to be built-in.  If that isn't
otherwise enabled somewhere, you can get build errors like:

linux-3.12.0-0.rc0.git1.1.fc21.armv7hl/drivers/dma/edma.c:593: undefined reference to `edma_free_slot'
drivers/built-in.o: In function `edma_terminate_all':
linux-3.12.0-0.rc0.git1.1.fc21.armv7hl/drivers/dma/edma.c:169: undefined reference to `edma_stop'
drivers/built-in.o: In function `edma_execute':
linux-3.12.0-0.rc0.git1.1.fc21.armv7hl/drivers/dma/edma.c:122: undefined reference to `edma_write_slot'
linux-3.12.0-0.rc0.git1.1.fc21.armv7hl/drivers/dma/edma.c:149: undefined reference to `edma_link'
linux-3.12.0-0.rc0.git1.1.fc21.armv7hl/drivers/dma/edma.c:152: undefined reference to `edma_start'

Make TI_EDMA select TI_PRIV_EDMA to avoid this.

Signed-off-by: Josh Boyer <jwboyer@fedoraproject.org>
Acked-by: Matt Porter <matt.porter@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>

Matt's @ti.com address bounces.  Update the MODULE_AUTHOR information in
edma.c to his Linaro address.

Signed-off-by: Josh Boyer <jwboyer@fedoraproject.org>
Acked-by: Matt Porter <matt.porter@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>

Pull timer code update from Thomas Gleixner:
 - armada SoC clocksource overhaul with a trivial merge conflict
 - Minor improvements to various SoC clocksource drivers

* 'timers/core' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  clocksource: armada-370-xp: Add detailed clock requirements in devicetree binding
  clocksource: armada-370-xp: Get reference fixed-clock by name
  clocksource: armada-370-xp: Replace WARN_ON with BUG_ON
  clocksource: armada-370-xp: Fix device-tree binding
  clocksource: armada-370-xp: Introduce new compatibles
  clocksource: armada-370-xp: Use CLOCKSOURCE_OF_DECLARE
  clocksource: armada-370-xp: Simplify TIMER_CTRL register access
  clocksource: armada-370-xp: Use BIT()
  ARM: timer-sp: Set dynamic irq affinity
  ARM: nomadik: add dynamic irq flag to the timer
  clocksource: sh_cmt: 32-bit control register support
  clocksource: em_sti: Convert to devm_* managed helpers

Pull CIFS fixes from Steve French:
 "Two minor cifs fixes and a minor documentation cleanup for cifs.txt"

* 'for-next' of git://git.samba.org/sfrench/cifs-2.6:
  cifs: update cifs.txt and remove some outdated infos
  cifs: Avoid calling unlock_page() twice in cifs_readpage() when using fscache
  cifs: Do not take a reference to the page in cifs_readpage_worker()

Pull UBI fixes from Artem Bityutskiy:
 "Just a single fastmap fix plus a regression fix"

* tag 'upstream-3.12-rc1' of git://git.infradead.org/linux-ubi:
  UBI: Fix invalidate_fastmap()
  UBI: Fix PEB leak in wear_leveling_worker()

Pull ubifs fix from Artem Bityutskiy:
 "Just one patch which fixes the power-cut recovery testing mode.

  I'll start using a single UBI/UBIFS tree instead of 2 trees from now
  on.  So in the future you'll get 1 small pull request instead of 2
  tiny ones"

* tag 'upstream-3.12-rc1' of git://git.infradead.org/linux-ubifs:
  UBIFS: remove invalid warn msg with tst_recovery enabled

Pull MIPS fixes from Ralf Baechle:
 "These are four patches for three construction sites:

   - Fix register decoding for the combination of multi-core processors
     and multi-threading.

   - Two more fixes that are part of the ongoing DECstation resurrection
     work.  One of these touches a DECstation-only network driver.

   - Finally Markos' trivial build fix for the AP/SP support.

  (With this applied now all MIPS defconfigs are building again)"

* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus:
  MIPS: kernel: vpe: Make vpe_attrs an array of pointers.
  MIPS: Fix SMP core calculations when using MT support.
  MIPS: DECstation I/O ASIC DMA interrupt handling fix
  MIPS: DECstation HRT initialization rearrangement

Pull x86 platform updates from Matthew Garrett:
 "Nothing amazing here, almost entirely cleanups and minor bugfixes and
  one bit of hardware enablement in the amilo-rfkill driver"

* 'for_linus' of git://cavan.codon.org.uk/platform-drivers-x86:
  platform/x86: panasonic-laptop: reuse module_acpi_driver
  samsung-laptop: fix config build error
  platform: x86: remove unnecessary platform_set_drvdata()
  amilo-rfkill: Enable using amilo-rfkill with the FSC Amilo L1310.
  wmi: parse_wdg() should return kernel error codes
  hp_wmi: Fix unregister order in hp_wmi_rfkill_setup()
  platform: replace strict_strto*() with kstrto*()
  x86: irst: use module_acpi_driver to simplify the code
  x86: smartconnect: use module_acpi_driver to simplify the code
  platform samsung-q10: use ACPI instead of direct EC calls
  thinkpad_acpi: add the ability setting TPACPI_LED_NONE by quirk
  thinkpad_acpi: return -NODEV while operating uninitialized LEDs

Pull misc SCSI driver updates from James Bottomley:
 "This patch set is a set of driver updates (megaraid_sas, fnic, lpfc,
  ufs, hpsa) we also have a couple of bug fixes (sd out of bounds and
  ibmvfc error handling) and the first round of esas2r checker fixes and
  finally the much anticipated big endian additions for megaraid_sas"

* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (47 commits)
  [SCSI] fnic: fnic Driver Tuneables Exposed through CLI
  [SCSI] fnic: Kernel panic while running sh/nosh with max lun cfg
  [SCSI] fnic: Hitting BUG_ON(io_req->abts_done) in fnic_rport_exch_reset
  [SCSI] fnic: Remove QUEUE_FULL handling code
  [SCSI] fnic: On system with >1.1TB RAM, VIC fails multipath after boot up
  [SCSI] fnic: FC stat param seconds_since_last_reset not getting updated
  [SCSI] sd: Fix potential out-of-bounds access
  [SCSI] lpfc 8.3.42: Update lpfc version to driver version 8.3.42
 ...

Pull SLAB update from Pekka Enberg:
 "Nothing terribly exciting here apart from Christoph's kmalloc
  unification patches that brings sl[aou]b implementations closer to
  each other"

* 'slab/next' of git://git.kernel.org/pub/scm/linux/kernel/git/penberg/linux:
  slab: Use correct GFP_DMA constant
  slub: remove verify_mem_not_deleted()
  mm/sl[aou]b: Move kmallocXXX functions to common code
  mm, slab_common: add 'unlikely' to size check of kmalloc_slab()
  mm/slub.c: beautify code for removing redundancy 'break' statement.
  slub: Remove unnecessary page NULL check
  slub: don't use cpu partial pages on UP
  mm/slub: beautify code for 80 column limitation and tab alignment
  mm/slub: remove 'per_cpu' which is useless variable

Pull input update from Dmitry Torokhov:
 "The only change is David Hermann's new EVIOCREVOKE evdev ioctl that
  allows safely passing file descriptors to input devices to session
  processes and later being able to stop delivery of events through
  these fds so that inactive sessions will no longer receive user input
  that does not belong to them"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
  Input: evdev - add EVIOCREVOKE ioctl

Sedat points out that I transposed some letters in "LRU" and wrote "RLU"
instead in one of the new comments explaining the flow.  Let's just fix
it.

Reported-by: Sedat Dilek <sedat.dilek@jpberlin.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Matt found that commit 27a7c642 ("partitions/efi: account for pmbr
size in lba") caused his GPT formatted eMMC device not to boot.  The
reason is that this commit enforced Linux to always check the lesser of
the whole disk or 2Tib for the pMBR size in LBA.  While most disk
partitioning tools out there create a pMBR with these characteristics,
Microsoft does not, as it always sets the entry to the maximum 32-bit
limitation - even though a drive may be smaller than that[1].

Loosen this check and only verify that the size is either the whole disk
or 0xFFFFFFFF.  No tool in its right mind would set it to any value
other than these.

[1] http://thestarman.pcministry.com/asm/mbr/GPT.htm#GPTPT



Reported-and-tested-by: Matt Porter <matt.porter@linaro.org>
Signed-off-by: Davidlohr Bueso <davidlohr@hp.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull writeback fix from Wu Fengguang:
 "A trivial writeback fix"

* tag 'writeback-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/wfg/linux:
  writeback: Do not sort b_io list only because of block device inode

The LRU list changes interacted badly with our nr_dentry_unused
accounting, and even worse with the new DCACHE_LRU_LIST bit logic.

This introduces helper functions to make sure everything follows the
proper dcache d_lru list rules: the dentry cache is complicated by the
fact that some of the hotpaths don't even want to look at the LRU list
at all, and the fact that we use the same list entry in the dentry for
both the LRU list and for our temporary shrinking lists when removing
things from the LRU.

The helper functions temporarily have some extra sanity checking for the
flag bits that have to match the current LRU state of the dentry.  We'll
remove that before the final 3.12 release, but considering how easy it
is to get wrong, this first cleanup version has some very particular
sanity checking.

Acked-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Acked-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: Björn JACKE <bj@sernet.de>
Signed-off-by: Steve French <smfrench@gmail.com>

When reading a single page with cifs_readpage(), we make a call to
fscache_read_or_alloc_page() which once done, asynchronously calls
the completion function cifs_readpage_from_fscache_complete(). This
completion function unlocks the page once it has been populated from
cache. The module then attempts to unlock the page a second time in
cifs_readpage() which leads to warning messages.

In case of a successful call to fscache_read_or_alloc_page() we should skip
the second unlock_page() since this will be called by the
cifs_readpage_from_fscache_complete() once the page has been populated by
fscache.

With the modifications to cifs_readpage_worker(), we will need to re-grab the
page lock in cifs_write_begin().

The problem was first noticed when testing new fscache patches for cifs.
https://bugzilla.redhat.com/show_bug.cgi?id=1005737



Signed-off-by: Sachin Prabhu <sprabhu@redhat.com>
Reviewed-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: Steve French <smfrench@gmail.com>

We do not need to take a reference to the pagecache in
cifs_readpage_worker() since the calling function will have already
taken one before passing the pointer to the page as an argument to the
function.

Signed-off-by: Sachin Prabhu <sprabhu@redhat.com>
Reviewed-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: Steve French <smfrench@gmail.com>

Pull hwmon fixes from Guenter Roeck:
 "Some more low risk cleanup patches:

   - Remove unnecessary pci_set_drvdata in k10temp driver from Jingoo Han
   - Fix return values in several drivers from Sachin Kamat
   - Remove redundant break in amc6821 driver from Sachin Kamat"

* tag 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
  hwmon: (k10temp) remove unnecessary pci_set_drvdata()
  hwmon: (tmp421) Fix return value
  hwmon: (amc6821) Remove redundant break
  hwmon: (amc6821) Fix return value
  hwmon: (ibmaem) Fix return value
  hwmon: (emc2103) Fix return value

Pull Xtensa updates from Chris Zankel.

* tag 'xtensa-next-20130912' of git://github.com/czankel/xtensa-linux:
  xtensa: Fix broken allmodconfig build
  xtensa: remove CCOUNT_PER_JIFFY
  xtensa: fix !CONFIG_XTENSA_CALIBRATE_CCOUNT build failure
  xtensa: don't use echo -e needlessly
  xtensa: new fast_alloca handler
  xtensa: keep a3 and excsave1 on entry to exception handlers
  xtensa: enable kernel preemption
  xtensa: check thread flags atomically on return from user exception

Pull aio changes from Ben LaHaise:
 "First off, sorry for this pull request being late in the merge window.
  Al had raised a couple of concerns about 2 items in the series below.
  I addressed the first issue (the race introduced by Gu's use of
  mm_populate()), but he has not provided any further details on how he
  wants to rework the anon_inode.c changes (which were sent out months
  ago but have yet to be commented on).

  The bulk of the changes have been sitting in the -next tree for a few
  months, with all the issues raised being addressed"

* git://git.kvack.org/~bcrl/aio-next: (22 commits)
  aio: rcu_read_lock protection for new rcu_dereference calls
  aio: fix race in ring buffer page lookup introduced by page migration support
  aio: fix rcu sparse warnings introduced by ioctx table lookup patch
  aio: remove unnecessary debugging from aio_free_ring()
  aio: table lookup: verify ctx pointer
  staging/lustre: kiocb->ki_left is removed
  aio: fix error handling and rcu usage in "convert the ioctx list to table lookup v3"
  aio: be defensive to ensure request batching is non-zero instead of BUG_ON()
  aio: convert the ioctx list to table lookup v3
  aio: double aio_max_nr in calculations
  aio: Kill ki_dtor
  aio: Kill ki_users
  aio: Kill unneeded kiocb members
  aio: Kill aio_rw_vect_retry()
  aio: Don't use ctx->tail unnecessarily
  aio: io_cancel() no longer returns the io_event
  aio: percpu ioctx refcount
  aio: percpu reqs_available
  aio: reqs_active -> reqs_available
  aio: fix build when migration is disabled
  ...

Pull generic hardirq option removal from Martin Schwidefsky:
 "All architectures now use generic hardirqs, s390 has been last to
  switch.

  With that the code under !CONFIG_GENERIC_HARDIRQS and the related
  HAVE_GENERIC_HARDIRQS and GENERIC_HARDIRQS config options can be
  removed.  Yay!"

* 'genirq' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
  Remove GENERIC_HARDIRQ config option

Pull kconfig fix from Michal Marek:
 "This is a fix for a regression caused by my previous pull request.

  A sed command in scripts/config that used colons as separator was
  accidentally changed to use slashes, which fails when you use slashes
  in a value.  Changing it back to colons is of course not a proper fix,
  but at least it will be broken in the same way it had been for four
  years.  A proper fix is pending"

* 'kconfig' of git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild:
  scripts/config: fix variable substitution command

Merge tag 'blackfin-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/realmz6/blackfin-linux

Pull blackfin updates from Steven Miao.

* tag 'blackfin-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/realmz6/blackfin-linux:
  blackfin: Ignore generated uImages
  blackfin: Add STMMAC platform data to enable dwmac1000 driver on BF60x.
  bf609: adv7343: add S-Video and Component output support
  bf609: add adv7343 video encoder support
  clock: add stmmac clock for ethernet driver
  blackfin: scb: Add SCB1 to SCB9 config options and data.
  blackfin: scb: Add system crossbar init code.

Pull crypto fixes from Herbert Xu:
 "This fixes a 7+ year race condition in the crypto API that causes
  sporadic crashes when multiple threads load the same algorithm.

  It also fixes the crct10dif algorithm again to prevent boot failures
  on systems where the initramfs tool ignores module softdeps"

* git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
  crypto: crct10dif - Add fallback for broken initrds
  crypto: api - Fix race condition in larval lookup

Commit 567b21e9


"mips: convert vpe_class to use dev_groups"

broke the build on MIPS since vpe_attrs should be an array
of 'struct device_attribute' pointers.

Fixes the following build problem:
arch/mips/kernel/vpe.c:1372:2: error: missing braces around initializer
[-Werror=missing-braces]
arch/mips/kernel/vpe.c:1372:2: error: (near initialization for 'vpe_attrs[0]')
[-Werror=missing-braces]

Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: John Crispin <blogic@openwrt.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/5819/


Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

After the last architecture switched to generic hard irqs the config
options HAVE_GENERIC_HARDIRQS & GENERIC_HARDIRQS and the related code
for !CONFIG_GENERIC_HARDIRQS can be removed.

Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>

Commit 229455bc02b87f7128f190c4491b4ceffff38648 accidentally changed the
separator between sed `s' command and its parameters from ':' to '/'.

Revert this change.

Reported-and-tested-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Clement Chauplannaz <chauplac@gmail.com>
Signed-off-by: Michal Marek <mmarek@suse.cz>

The TCBIND register is only available if the core has MT support. It
should not be read otherwise. Secondly, the number of TCs (siblings)
are calculated differently depending on if the kernel is configured
as SMVP or SMTC.

Signed-off-by: Leonid Yegoshin <Leonid.Yegoshin@imgtec.com>
Signed-off-by: Steven J. Hill <Steven.Hill@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/5822/


Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

This change complements commit d0da7c002f7b2a93582187a9e3f73891a01d8ee4
and brings clear_ioasic_irq back, renaming it to clear_ioasic_dma_irq at
the same time, to make I/O ASIC DMA interrupts functional.

Unlike ordinary I/O ASIC interrupts DMA interrupts need to be deasserted
by software by writing 0 to the respective bit in I/O ASIC's System
Interrupt Register (SIR), similarly to how CP0.Cause.IP0 and CP0.Cause.IP1
bits are handled in the CPU (the difference is SIR DMA interrupt bits are
R/W0C so there's no need for an RMW cycle).  Otherwise the handler is
reentered over and over again.

The only current user is the DEC LANCE Ethernet driver and its extremely
uncommon DMA memory error handler that does not care when exactly the
interrupt is cleared.  Anticipating the use of DMA interrupts by the Zilog
SCC driver this change however exports clear_ioasic_dma_irq for device
drivers to choose the right application-specific sequence to clear the
request explicitly rather than calling it implicitly in the .irq_eoi
handler of `struct irq_chip'.  Previously these interrupts were cleared in
the .end handler of the said structure, before it was removed.

Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/5826/


Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

Not all I/O ASIC versions have the free-running counter implemented, an
early revision used in the 5000/1xx models aka 3MIN and 4MIN did not have
it.  Therefore we cannot unconditionally use it as a clock source.
Fortunately if not implemented its register slot has a fixed value so it
is enough if we check for the value at the end of the calibration period
being the same as at the beginning.

This also means we need to look for another high-precision clock source on
the systems affected.  The 5000/1xx can have an R4000SC processor
installed where the CP0 Count register can be used as a clock source.
Unfortunately all the R4k DECstations suffer from the missed timer
interrupt on CP0 Count reads erratum, so we cannot use the CP0 timer as a
clock source and a clock event both at a time.  However we never need an
R4k clock event device because all DECstations have a DS1287A RTC chip
whose periodic interrupt can be used as a clock source.

This gives us the following four configuration possibilities for I/O ASIC
DECstations:

1. No I/O ASIC counter and no CP0 timer, e.g. R3k 5000/1xx (3MIN).

2. No I/O ASIC counter but the CP0 timer, i.e. R4k 5000/150 (4MIN).

3. The I/O ASIC counter but no CP0 timer, e.g. R3k 5000/240 (3MAX+).

4. The I/O ASIC counter and the CP0 timer, e.g. R4k 5000/260 (4MAX+).

For #1 and #2 this change stops the I/O ASIC free-running counter from
being installed as a clock source of a 0Hz frequency.  For #2 it also
arranges for the CP0 timer to be used as a clock source rather than a
clock event device, because having an accurate wall clock is more
important than a high-precision interval timer.  For #3 there is no
change.  For #4 the change makes the I/O ASIC free-running counter
installed as a clock source so that the CP0 timer can be used as a clock
event device.

Unfortunately the use of the CP0 timer as a clock event device relies on a
succesful completion of c0_compare_interrupt.  That never happens, because
while waiting for a CP0 Compare interrupt to happen the function spins in
a loop reading the CP0 Count register.  This makes the CP0 Count erratum
trigger reliably causing the interrupt waited for to be lost in all cases.
As a result #4 resorts to using the CP0 timer as a clock source as well,
just as #2.  However we want to keep this separate arrangement in case
(hope) c0_compare_interrupt is eventually rewritten such that it avoids
the erratum.

Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/5825/


Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

We have the build infrastructure to generate uImages so we should ignore
the resulting generated files.

Signed-off-by: Mark Brown <broonie@linaro.org>
Acked-by: Mike Frysinger <vapier@gentoo.org>

- Enable GMAC
- Set propler DMA PBL
- Disable DMA store and forward mode
- Select PTP input clock from MII
clock.

Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Steven Miao <realmz6@gmail.com>

Signed-off-by: Scott Jiang <scott.jiang.linux@gmail.com>

Signed-off-by: Scott Jiang <scott.jiang.linux@gmail.com>

Signed-off-by: Steven Miao <realmz6@gmail.com>