When setting a new display mode, dw_hdmi_setup() calls
dw_hdmi_enable_video_path(), which disables all hdmi clocks, including
the audio clock.

We should only (re-)enable the audio clock if audio was already enabled
when setting the new mode.

Without this patch, on RK3288, there will be HDMI audio on some monitors
if i2s was played to headphone when the monitor was plugged.
ACER H277HU and ASUS PB278 are two of the monitors showing this issue.

Signed-off-by: Cheng-Yi Chiang <cychiang@chromium.org>
Signed-off-by: Daniel Kurtz <djkurtz@chromium.org>
Signed-off-by: Yakir Yang <ykk@rock-chips.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191008102145.55134-1-cychiang@chromium.org

The bridge might have special requirmentes on the input bus. This
is e.g. used by the imx-nwl bridge.

Signed-off-by: Guido Günther <agx@sigxcpu.org>
Reviewed-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Stefan Agner <stefan@agner.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/1567078215-31601-3-git-send-email-robert.chiras@nxp.com

Currently, the MXSFB DRM driver only supports a panel. But, its output
display signal can also be redirected to another encoder, like a DSI
controller. In this case, that DSI controller may act like a drm_bridge.
In order support this use-case too, this patch adds support for drm_bridge
in mxsfb.

Signed-off-by: Robert Chiras <robert.chiras@nxp.com>
Tested-by: Guido Günther <agx@sigxcpu.org>
Signed-off-by: Stefan Agner <stefan@agner.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/1567078215-31601-2-git-send-email-robert.chiras@nxp.com

Fixes: 83fa9842

 ("drm/dp-mst: Drop connection_mutex check")
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20191011010907.103309-8-lucas.demarchi@intel.com

Fixes gcc '-Wunused-but-set-variable' warning:

drivers/gpu/drm/omapdrm/dss/hdmi4_core.c: In function hdmi4_audio_config:
drivers/gpu/drm/omapdrm/dss/hdmi4_core.c:689:6: warning: variable err set but not used [-Wunused-but-set-variable]

It is not used since commit f5bab222

 ("OMAPDSS:
HDMI: Add OMAP5 HDMI support")

Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: zhengbin <zhengbin13@huawei.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1570518949-47574-5-git-send-email-zhengbin13@huawei.com

Fixes gcc '-Wunused-but-set-variable' warning:

drivers/gpu/drm/omapdrm/dss/hdmi5_core.c: In function hdmi5_audio_config:
drivers/gpu/drm/omapdrm/dss/hdmi5_core.c:812:6: warning: variable err set but not used [-Wunused-but-set-variable]

It is not used since commit f5bab222

 ("OMAPDSS:
HDMI: Add OMAP5 HDMI support")

Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: zhengbin <zhengbin13@huawei.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1570518949-47574-4-git-send-email-zhengbin13@huawei.com

Fixes gcc '-Wunused-but-set-variable' warning:

drivers/gpu/drm/omapdrm/dss/dsi.c: In function dsi_proto_timings:
drivers/gpu/drm/omapdrm/dss/dsi.c:3562:46: warning: variable tclk_trail set but not used [-Wunused-but-set-variable]

It is not used since commit 9960aa7c

 ("drm/omap:
move omapdss & displays under omapdrm")

Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: zhengbin <zhengbin13@huawei.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1570518949-47574-3-git-send-email-zhengbin13@huawei.com

Fixes gcc '-Wunused-but-set-variable' warning:

drivers/gpu/drm/omapdrm/omap_fb.c: In function omap_framebuffer_update_scanout:
drivers/gpu/drm/omapdrm/omap_fb.c:130:16: warning: variable plane set but not used [-Wunused-but-set-variable]

It is not used since commit 2ecceeb5

 ("drm/omap:
Move buffer pitch/offset to drm_framebuffer")

Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: zhengbin <zhengbin13@huawei.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1570518949-47574-2-git-send-email-zhengbin13@huawei.com

Some VOP's (such as px30) dclk_pol bit is at the last.
So it is necessary to distinguish dclk_pol and pin_pol.

Signed-off-by: Nickey Yang <nickey.yang@rock-chips.com>
Reviewed-by: Sandy Huang <hjc@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20191010034452.20260-2-nickey.yang@rock-chips.com

The rockchip_gem_alloc_object function is not exported so
make it static to avoid the following sparse warning:

drivers/gpu/drm/rockchip/rockchip_drm_gem.c:297:28: warning: symbol 'rockchip_gem_alloc_object' was not declared. Should it be static?

Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20191009121022.17478-1-ben.dooks@codethink.co.uk

Include rockchip_drm_drv.h for definition of vop_platform_driver
to avoid the following sparse warning:

drivers/gpu/drm/rockchip/rockchip_vop_reg.c:982:24: warning: symbol 'vop_platform_driver' was not declared. Should it be static?

Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20191009132134.18384-1-ben.dooks@codethink.co.uk

Simplify this function implementation by using a known wrapper function.

This issue was detected by using the Coccinelle software.

Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://patchwork.freedesktop.org/patch/msgid/0666bc0b-6624-21a0-47c4-b78e2a3b3ad5@web.de

@swap@
identifier TEMP;
expression A,B;
@@
- TEMP = A;
- A = B;
- B = TEMP;
+ swap(A, B);

@@
type T;
identifier swap.TEMP;
@@
(
- T TEMP;
|
- T TEMP = {...};
)
... when != TEMP

Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Boris Brezillon <bbrezillon@kernel.org>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191010131159.17346-3-ville.syrjala@linux.intel.com


Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>

On SoCs with DMM/TILER, we have two ways to allocate buffers: normal
dma_alloc or via DMM (which basically functions as an IOMMU). DMM can
map 128MB at a time, and we only map the DMM buffers when they are used
(i.e. not at alloc time). If DMM is present, omapdrm always uses DMM.

There are use cases that require lots of big buffers that are being used
at the same time by different IPs. At the moment the userspace has a
hard maximum of 128MB.

This patch adds three new flags that can be used by the userspace to
solve the situation:

OMAP_BO_MEM_CONTIG: The driver will use dma_alloc to get the memory.
This can be used to avoid DMM if the userspace knows it needs more than
128M of memory at the same time.

OMAP_BO_MEM_DMM: The driver will use DMM to get the memory. There's not
much use for this flag at the moment, as on platforms with DMM it is
used by default, but it's here for completeness.

OMAP_BO_MEM_PIN: The driver will pin the memory at alloc time, and keep
it pinned. This can be used to 1) get an error at alloc time if DMM
space is full, and 2) get rid of the constant pin/unpin operations which
may have some effect on performance.

If none of the flags are given, the behavior is the same as currently.

Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191010120000.1421-9-jjhiblot@ti.com

Add a helper function omap_gem_validate_flags() which validates the
omap_bo flags passed from the userspace.

Also drop the dev_err() message, as the userspace can cause that at
will.

Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191010120000.1421-8-jjhiblot@ti.com

omap_gem_new() has a comment about OMAP_BO_SCANOUT which does not make
sense. Also, for the TILER case, we drop OMAP_BO_SCANOUT flag for some
reason.

It's not clear what the original purpose of OMAP_BO_SCANOUT is, but
presuming it means "scanout buffer, something that can be consumed by
DSS", this patch cleans up the above issues.

Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191010120000.1421-7-jjhiblot@ti.com

OMAP_BO_TILED does not make sense, as OMAP_BO_TILED_* values are not
bitmasks but normal values. As we already have OMAP_BO_TILED_MASK for
the mask, we can remove OMAP_BO_TILED and use OMAP_BO_TILED_MASK
instead.

Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191010120000.1421-6-jjhiblot@ti.com

Reorder OMAP_BO flags and improve the comments.

Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191010120000.1421-5-jjhiblot@ti.com

Allow NULL to be passed in 'dma_addr' for omap_gem_pin(), in case the
caller does not need the dma_addr.

Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191010120000.1421-4-jjhiblot@ti.com

Add omap_gem_unpin_locked() which is a version of omap_gem_unpin() that
expects the caller to hold the omap_obj lock.

Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191010120000.1421-3-jjhiblot@ti.com

This would give us a WARN_ON() if the pin/unpin calls are unbalanced.

Proposed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191010120000.1421-2-jjhiblot@ti.com

Add an optional CRTC gamma LUT support, and enable it on RK3288.
This is currently enabled via a separate address resource,
which needs to be specified in the devicetree.

The address resource is required because on some SoCs, such as
RK3288, the LUT address is after the MMU address, and the latter
is supported by a different driver. This prevents the DRM driver
from requesting an entire register space.

The current implementation works for RGB 10-bit tables, as that
is what seems to work on RK3288.

Tested-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20191010194351.17940-3-ezequiel@collabora.com

Add the register specifier description for an
optional gamma LUT address.

Reviewed-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20191010194351.17940-2-ezequiel@collabora.com

The drm_sched_fence_ops_{scheduled,finished} are not exported
from the file so make them static to avoid the following
warnings from sparse:

drivers/gpu/drm/scheduler/sched_fence.c:131:28: warning: symbol 'drm_sched_fence_ops_scheduled' was not declared. Should it be static?
drivers/gpu/drm/scheduler/sched_fence.c:137:28: warning: symbol 'drm_sched_fence_ops_finished' was not declared. Should it be static?

Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191009121447.31017-1-ben.dooks@codethink.co.uk

The rectangles are usually clipped, but it can be useful to have
them unclipped, for example for cursor planes.

Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
[mlankhorst: Change cursor plane to hardware performing clipping. (Ville)
             Fix dst description that went missing.]
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191010112918.15724-1-maarten.lankhorst@linux.intel.com

Remove duplicated include.

Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20191010115213.115706-1-yuehaibing@huawei.com

Private atomic objects have grown their own locking with

commit b962a120


Author: Rob Clark <robdclark@gmail.com>
Date:   Mon Oct 22 14:31:22 2018 +0200

    drm/atomic: integrate modeset lock with private objects

which means we're no longer relying on connection_mutex for mst state
locking needs.

Cc: Lyude Paul <lyude@redhat.com>
Cc: Sean Paul <sean@poorly.run>
Reviewed-by: Lyude Paul <lyude@redhat.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191009224113.5432-1-daniel.vetter@ffwll.ch

This patch enables Dynamic Range and Mastering InfoFrame on H6.

Cc: Maxime Ripard <maxime.ripard@bootlin.com>
Cc: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://patchwork.freedesktop.org/patch/msgid/HE1PR06MB40119DBC0DAE7BA251DF7074AC9B0@HE1PR06MB4011.eurprd06.prod.outlook.com

This patch enables Dynamic Range and Mastering InfoFrame on GXL, GXM and G12A.

Cc: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://patchwork.freedesktop.org/patch/msgid/HE1PR06MB4011BB614A49253FD074BCCBAC9B0@HE1PR06MB4011.eurprd06.prod.outlook.com

This patch enables Dynamic Range and Mastering InfoFrame on RK3328 and RK3399.

Cc: Sandy Huang <hjc@rock-chips.com>
Cc: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://patchwork.freedesktop.org/patch/msgid/HE1PR06MB4011C9579CA6BBCD96C87810AC9B0@HE1PR06MB4011.eurprd06.prod.outlook.com

Add support for configuring Dynamic Range and Mastering InfoFrame from
the hdr_output_metadata connector property.

This patch adds a use_drm_infoframe flag to dw_hdmi_plat_data that platform
drivers use to signal when Dynamic Range and Mastering infoframes is supported.
This flag is needed because Amlogic GXBB and GXL report same DW-HDMI version,
and only GXL support DRM InfoFrame.

These changes were based on work done by Zheng Yang <zhengyang@rock-chips.com>
to support DRM InfoFrame on the Rockchip 4.4 BSP kernel at [1] and [2]

[1] https://github.com/rockchip-linux/kernel/tree/develop-4.4
[2] https://github.com/rockchip-linux/kernel/commit/d1943fde81ff41d7cca87f4a42f03992e90bddd5



Cc: Zheng Yang <zhengyang@rock-chips.com>
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://patchwork.freedesktop.org/patch/msgid/HE1PR06MB4011D7B916CBF8B740ACC45FAC9B0@HE1PR06MB4011.eurprd06.prod.outlook.com

According to the downstream Android sources, the anx7808 variants use
address 0x78 for TX_P0 and the anx781x variants use address 0x70. Since
the datasheets aren't available for these devices, and we only have the
downstream kernel sources to look at, let's assume that these addresses
are fixed based on the model, and pass the i2c addresses to the driver
via the data pointer in the driver's of_match_table.

Signed-off-by: Brian Masney <masneyb@onstation.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190922175940.5311-1-masneyb@onstation.org

commit d6abe6df

 ("drm/bridge: sil_sii8620: do not have a dependency
of RC_CORE") changed the driver to select both RC_CORE and INPUT.
However, this causes problems with other drivers, in particular an input
driver that depends on MFD_INTEL_LPSS_PCI (to be added in a separate
commit):

  drivers/clk/Kconfig:9:error: recursive dependency detected!
  drivers/clk/Kconfig:9:        symbol COMMON_CLK is selected by MFD_INTEL_LPSS
  drivers/mfd/Kconfig:566:      symbol MFD_INTEL_LPSS is selected by MFD_INTEL_LPSS_PCI
  drivers/mfd/Kconfig:580:      symbol MFD_INTEL_LPSS_PCI is implied by KEYBOARD_APPLESPI
  drivers/input/keyboard/Kconfig:73:    symbol KEYBOARD_APPLESPI depends on INPUT
  drivers/input/Kconfig:8:      symbol INPUT is selected by DRM_SIL_SII8620
  drivers/gpu/drm/bridge/Kconfig:83:    symbol DRM_SIL_SII8620 depends on DRM_BRIDGE
  drivers/gpu/drm/bridge/Kconfig:1:     symbol DRM_BRIDGE is selected by DRM_PL111
  drivers/gpu/drm/pl111/Kconfig:1:      symbol DRM_PL111 depends on COMMON_CLK

According to the docs and general consensus, select should only be used
for non user-visible symbols, but both RC_CORE and INPUT are
user-visible. Furthermore almost all other references to INPUT
throughout the kernel config are depends, not selects. For this reason
the first part of this change reverts the commit.

In order to address the original reason for the commit, namely
that not all boards use the remote controller functionality and hence
should not need have to deal with RC_CORE, the second part of this
change now makes the remote control support in the driver optional and
contingent on RC_CORE being defined. And with this the hard dependency
on INPUT also goes away as that is only needed if RC_CORE is defined
(which in turn already depends on INPUT).

CC: Inki Dae <inki.dae@samsung.com>
CC: Andrzej Hajda <a.hajda@samsung.com>
CC: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
CC: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Ronald Tschalär <ronald@innovation.ch>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
[a.hajda: applied fixup provided by Arnd Bergmann]
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190419081926.13567-2-ronald@innovation.ch

Move from the deprecated i2c_new_dummy() to devm_i2c_new_dummy_device().
We now get an ERRPTR which we use in error handling and we can skip
removal of the created devices.

Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191008203322.3238-1-wsa+renesas@sang-engineering.com

Fixes the following warning:
../include/drm/drm_atomic_state_helper.h:1: warning: no structured comments found

Fixes: 9ef8a9dc

 ("drm: Extract drm_atomic_state_helper.[hc]")
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Daniel Vetter <daniel.vetter@intel.com>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Maxime Ripard <mripard@kernel.org>
Cc: Sean Paul <sean@poorly.run>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: dri-devel@lists.freedesktop.org
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20191007151921.27099-1-sean@poorly.run

I'm embarassed to say that even though I've touched
vop_crtc_mode_fixup() twice and I swear I tested it, there's still a
stupid glaring bug in it.  Specifically, on veyron_minnie (with all
the latest display timings) we want to be setting our pixel clock to
66,666,666.67 Hz and we tell userspace that's what we set, but we're
actually choosing 66,000,000 Hz.  This is confirmed by looking at the
clock tree.

The problem is that in drm_display_mode_from_videomode() we convert
from Hz to kHz with:

  dmode->clock = vm->pixelclock / 1000;

...and drm_display_mode_from_videomode() is called from panel-simple
when we have an "override_mode" like we do on veyron_minnie.  See
commit 123643e5 ("ARM: dts: rockchip: Specify
rk3288-veyron-minnie's display timings").

...so when the device tree specifies a clock of 66666667 for the panel
then DRM translates that to 66666000.  The clock framework will always
pick a clock that is _lower_ than the one requested, so it will refuse
to pick 66666667 and we'll end up at 66000000.

While we could try to fix drm_display_mode_from_videomode() to round
to the nearest kHz and it would fix our problem, it wouldn't help if
the clock we actually needed was 60,000,001 Hz.  We could
alternatively have DRM always round up, but maybe this would break
someone else who already baked in the assumption that DRM rounds down.
Specifically note that clock drivers are not consistent about whether
they round up or round down when you call clk_set_rate().  We know how
Rockchip's clock driver works, but (for instance) you can see that on
most Qualcomm clocks the default is clk_rcg2_ops which rounds up.

Let's solve this by just adding 999 Hz before calling
clk_round_rate().  This should be safe and work everywhere.  As
discussed in more detail in comments in the commit, Rockchip's PLLs
are configured in a way that there shouldn't be another PLL setting
that is only a few kHz off so we won't get mixed up.

NOTE: if this is picked to stable, it's probably easiest to first pick
commit 527e4ca3 ("drm/rockchip: Base adjustments of the mode based
on prev adjustments") which shouldn't hurt in stable.

Fixes: b59b8de3

 ("drm/rockchip: return a true clock rate to adjusted_mode")
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20191003114726.v2.1.Ib233b3e706cf6317858384264d5b0ed35657456e@changeid

panfrost_core_dump() has never existed in mainline, so remove it and add
a TODO entry that core dump support is currently lacking.

Signed-off-by: Steven Price <steven.price@arm.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20191009094456.9704-2-steven.price@arm.com

Panfrost uses multiple schedulers (one for each slot, so 2 in reality),
and on a timeout has to stop all the schedulers to safely perform a
reset. However more than one scheduler can trigger a timeout at the same
time. This race condition results in jobs being freed while they are
still in use.

When stopping other slots use cancel_delayed_work_sync() to ensure that
any timeout started for that slot has completed. Also use
mutex_trylock() to obtain reset_lock. This means that only one thread
attempts the reset, the other threads will simply complete without doing
anything (the first thread will wait for this in the call to
cancel_delayed_work_sync()).

While we're here and since the function is already dependent on
sched_job not being NULL, let's remove the unnecessary checks.

Fixes: aa202367

 ("drm/panfrost: Prevent concurrent resets")
Tested-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Steven Price <steven.price@arm.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20191009094456.9704-1-steven.price@arm.com

devm_regulator_get() is used to populate pfdev->regulator which ensures
that this cannot be NULL (a dummy regulator will be returned if
necessary). So remove the check in panfrost_devfreq_target().

Signed-off-by: Steven Price <steven.price@arm.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20191004144413.42586-1-steven.price@arm.com

Currently the property docs don't specify whether it's okay for two planes to
have the same zpos value and what user-space should expect in this case.

The unspoken, legacy rule used in the past was to make user-space figure
out the zpos from object IDs. However some drivers break this rule,
that's why the ordering is documented as unspecified in case the zpos
property is missing. User-space should rely on the zpos property only.

There are some cases in which user-space might read identical zpos
values for different planes.

For instance, in case the property is mutable, user-space might set two
planes' zpos to the same value. This is necessary to support user-space
using the legacy DRM API where atomic commits are not possible:
user-space needs to update the planes' zpos one by one.

Because of this, user-space should handle multiple planes with the same
zpos.

While at it, remove the assumption that zpos is only for overlay planes.

Additionally, update the drm_plane_state.zpos docs to clarify that zpos
disambiguation via plane object IDs is a recommendation for drivers, not
something user-space can rely on. In other words, when user-space sets
the same zpos on two planes, drivers should rely on the plane object ID.

v2: clarify drm_plane_state.zpos docs (Daniel)

v3: zpos is for all planes (Marius, Daniel)

v4: completely reword the drm_plane_state.zpos docs to make it clear the
recommendation to use plane IDs is for drivers in case user-space uses
duplicate zpos values (Pekka)

v5: reword commit message (Pekka, James)

v6: remove mention of Arm GPUs having planes which can't overlap,
because this isn't uAPI yet (Daniel)

Signed-off-by: Simon Ser <contact@emersion.fr>
Reviewed-by: Pekka Paalanen <ppaalanen@gmail.com>
Cc: Marius Vlad <marius.vlad@collabora.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: James Qian Wang <james.qian.wang@arm.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/T5nHrvXH0GKOp6ONaFHk-j2cwEb4_4C_sBz9rNw8mmPACuut-DQqC74HMAFKZH3_Q15E8a3YnmKCxap-djKA71VVZv_T-tFxaB0he13O7yA=@emersion.fr