This patch adds support for device tree source for Samsung Rinato
board (Gear 2) based on Exynos3250 SoC.

This dts file support following features:
- eMMC
- Main PMIC (Samsung S2MPS14)
- Interface PMIC (Maxim MAX77836, MUIC, fuel-gauge, charger)
- RTC of Exynos3250
- ADC of Exynos3250 with NTC thermistor
- I2S of Exynos3250
- TMU of Exynos3250
- MFC of Exynos3250
- Secure firmware for Exynos3250 secondary cpu boot
- Serial ports of Exynos3250
- gpio-key for power key

Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Signed-off-by: Seung-Woo Kim <sw0312.kim@samsung.com>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>

Recent patch by Tomasz Figa ("irqchip: gic: Fix core ID calculation
when topology is read from DT") fixed GIC driver to filter cluster ID
from values returned by cpu_logical_map() for SoCs having registers
mapped without per-CPU banking making it is possible to add CPU nodes
for Exynos4 SoCs.  In case of Exynos SoCs these CPU nodes are also
required by future changes adding initialization of cpuidle states in
Exynos cpuidle driver through DT.

Tested on Origen board (Exynos4210 SoC) and Trats2 (Exynos4412 SoC).

Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>

Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>

The MAX77693 is a companion power management IC for smart phones and
tablets.

The MAX77693 contains input over-voltage protection (OVP),
a fully-integrated 2.5A switching charger for Lithium Ion battery with
integrated battery disconnect, OTG/accessory 5V output power,
a high-current white LED driver for camera flash, two safeout LDOs,
a haptic motor driver, Model Gauge m3 battery fuel gauge and MicroUSB
Interface Controller (MUIC). I2C serial interface is used for
communicating.

Add MAX77693 node to the Trats2 board. This allows using:
 - charger regulator,
 - 2 safeout LDO regulators (for USB OTG),
 - extcon.

Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>

This patch adds sleep mode pin configuration using pin control hog
mechanism to configure states of GPIO pins in sleep mode. This is
required to reduce leakage current in sleep mode and prevent glitching
of components on the board.

Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>

This patch adds a convenient macro which constructs an Exynos pinctrl
pinconf node containing properties needed to configure sleep state of
given pin with given parameters. It will be used by further patch which
adds a large number of sleep states for pins that need such
configuration on certain boards.

Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>

In MAX77686 PMIC two regulators dedicated for eMMC memory can be
controlled both by I2C interface and a GPIO pin, with the resulting
regulator state being a logical OR of both. Since the GPIO control is
used both by the kernel and the lowest level bootloader at reset, the
regulator should be disabled by I2C control to allow it to be turned off
by GPIO control.

This patch removes regulator-always-on properties from both regulators
and, while at it, also unsupported regulator-mem-off.

Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>

MMC capability for HS200 is parsed in mmc/core/host.c as
dts string "mmc-hs200-1_8v".

This patch corrects the dts string for Exynos5420 based peach-pit
and Exynos5800 based peach-pi boards.

Signed-off-by: Naveen Krishna Chatradhi <ch.naveen@samsung.com>
Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>

commit 546b117fdf17 ("rtc: s3c: add support for RTC of Exynos3250 SoC")
added an "rtc_src" DT property for the Samsung's S3C Real Time Clock
controller that specifies the 32.768 kHz clock that uses the RTC as
its source clock. In the case of the Exynos5250 based Snow board, the
Maxim 77686 32kHz AP clock is used as the source clock.

Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>

commit 546b117fdf17 ("rtc: s3c: add support for RTC of Exynos3250 SoC")
added an "rtc_src" DT property for the Samsung's S3C Real Time Clock
controller that specifies the 32.768 kHz clock that uses the RTC as
its source clock. In the case of the Peach Pit and Pi machines, the
Maxim 77802 32kHz AP clock is used as the source clock.

Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Reviewed-by: Doug Anderson <dianders@chromium.org>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>

The PWM block is required for system clock source so it must be always
enabled. This patch fixes boot issues on SMDK6410 which did not have
the node enabled explicitly for other purposes.

Fixes: eeb93d02 ("clocksource: of: Respect device tree node status")

Signed-off-by: Tomasz Figa <tomasz.figa@gmail.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>

Adds initial support for the HP Chromebook 11.

Cc: Vincent Palatin <vpalatin@chromium.org>
Cc: Doug Anderson <dianders@chromium.org>
Cc: Stephan van Schaik <stephan@synkhronix.com>
Signed-off-by: Andreas Faerber <afaerber@suse.de>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Reviewed-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>

There's no need for a simple-bus, place the smsc,usb3503a directly into
the root node. That's what we're going to do on exynos5250-spring.

Reported-by: Tomasz Figa <t.figa@samsung.com>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Andreas Faerber <afaerber@suse.de>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>

The GPIO flag 2 has no constant assigned, so this was probably
active-low.

Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Andreas Faerber <afaerber@suse.de>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>

Use the new style of referencing inherited nodes, use symbolic names,
tidy indentation and reorder includes.

Goal is the alignment of all exynos5250 based device trees for
comparison.

Signed-off-by: Andreas Faerber <afaerber@suse.de>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
[kgene.kim@samsung.com: rebased]
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>

Use the new style for referencing inherited nodes and use symbolic
names. Goal is the alignment of all exynos5250 based device trees
for comparison.

Signed-off-by: Andreas Faerber <afaerber@suse.de>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
[kgene.kim@samsung.com: rebased and squashed]
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>

exynos5250-cros-common.dtsi had an empty /chosen node.
Fill in exemplary boot arguments.

Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Andreas Faerber <afaerber@suse.de>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>

Use the new style of referencing inherited nodes and use symbolic
names. Reorder one pinctrl node in GPIO order.
Goal is the alignment of all exynos5250 based device trees for
comparison.

Suggested-by: Doug Anderson <dianders@chromium.org>
Reviewed-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Andreas Faerber <afaerber@suse.de>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
[kgene.kim@samsung.com: rebased and squashed]
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>

Allows them to be extended by reference.

Reviewed-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Andreas Faerber <afaerber@suse.de>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>

Explicitly set the dr_mode for the second dwc3 controller on the
Arndale Octa board to host mode. This is required to ensure the
controller is initialized in the right mode if the kernel is build
with USB gadget support.

Reported-By: Andreas Faerber <afaerber@suse.de>
Signed-off-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>

In case the optional dr_mode property isn't set in the dwc3 nodes the
the controller will go into OTG mode if both USB host and USB gadget
functionality are enabled in the kernel configuration. Unfortunately
this results in USB not working on exynos5420-peach-pit and
exynos5800-peach-pi with such a kernel configuration unless manually
change the mode. To resolve that explicitly configure the dual role
mode as host.

Signed-off-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Reviewed-by: Andreas Faerber <afaerber@suse.de>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>

The EIRSR and ELRSR registers are 32-bit registers on GICv2, and we
store these as an array of two such registers on the vgic vcpu struct.
However, we access them as a single 64-bit value or as a bitmap pointer
in the generic vgic code, which breaks BE support.

Instead, store them as u64 values on the vgic structure and do the
word-swapping in the assembly code, which already handles the byte order
for BE systems.

Tested-by: Victor Kamensky <victor.kamensky@linaro.org>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>

CM-QS600 is a APQ8064 based computer on module.
The details are available at
http://compulab.co.il/products/computer-on-modules/cm-qs600/



Signed-off-by: Mike Rapoport <mike.rapoport@gmail.com>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Kumar Gala <galak@codeaurora.org>

This DTS has support for the Sony Xperia Z1 phone (codenamed Honami).
This first version of the DTS supports just a serial console.

Signed-off-by: Tim Bird <tim.bird@sonymobile.com>
Tested-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Kumar Gala <galak@codeaurora.org>

Add SATA PHY and SATA AHCI controller nodes to device tree to enable
generic ahci support on the IPQ8064/AP148 board.

Signed-off-by: Kumar Gala <galak@codeaurora.org>

Commit:
b8865767 ARM: KVM: user_mem_abort: support stage 2 MMIO page mapping

introduced some code in user_mem_abort that failed to compile if
STRICT_MM_TYPECHECKS was enabled.

This patch fixes up the failing comparison.

Signed-off-by: Steve Capper <steve.capper@linaro.org>
Reviewed-by: Kim Phillips <kim.phillips@linaro.org>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>

Commit 97a13e52 ('net: phy: mdio-sun4i: don't select REGULATOR') removed
the select of REGULATOR, which means that it now has to be explicitly
enabled in the defconfig or things won't work very well.

In particular, this fixes a problem with SD/MMC not probing on my A31-based
board.

Cc: Beniamino Galvani <b.galvani@gmail.com>
Signed-off-by: Olof Johansson <olof@lixom.net>

When creating or moving a memslot, make sure the IPA space is within the
addressable range of the guest.  Otherwise, user space can create too
large a memslot and KVM would try to access potentially unallocated page
table entries when inserting entries in the Stage-2 page tables.

Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>

This patch adds the necessary support for all host kernel PGSIZE and
VA_SPACE configuration options for both EL2 and the Stage-2 page tables.

However, for 40bit and 42bit PARange systems, the architecture mandates
that VTCR_EL2.SL0 is maximum 1, resulting in fewer levels of stage-2
pagge tables than levels of host kernel page tables.  At the same time,
systems with a PARange > 42bit, we limit the IPA range by always setting
VTCR_EL2.T0SZ to 24.

To solve the situation with different levels of page tables for Stage-2
translation than the host kernel page tables, we allocate a dummy PGD
with pointers to our actual inital level Stage-2 page table, in order
for us to reuse the kernel pgtable manipulation primitives.  Reproducing
all these in KVM does not look pretty and unnecessarily complicates the
32-bit side.

Systems with a PARange < 40bits are not yet supported.

 [ I have reworked this patch from its original form submitted by
   Jungseok to take the architecture constraints into consideration.
   There were too many changes from the original patch for me to
   preserve the authorship.  Thanks to Catalin Marinas for his help in
   figuring out a good solution to this challenge.  I have also fixed
   various bugs and missing error code handling from the original
   patch. - Christoffer ]

Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Jungseok Lee <jungseoklee85@gmail.com>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>

The kernel used to contain two functions for length-delimited,
case-insensitive string comparison, strnicmp with correct semantics and
a slightly buggy strncasecmp.  The latter is the POSIX name, so strnicmp
was renamed to strncasecmp, and strnicmp made into a wrapper for the new
strncasecmp to avoid breaking existing users.

To allow the compat wrapper strnicmp to be removed at some point in the
future, and to avoid the extra indirection cost, do
s/strnicmp/strncasecmp/g.

Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Cc: Russell King <linux@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Fix wrong compatible string of Exynos3250 RTC (Real-Time Clock) dt node.
The RTC of Exynos3250 must need additional source clock (XrtcXTI).

Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

There is really no point in faulting in memory regions page by page
if they are not backed by demand paged system RAM but by a linear
passthrough mapping of a host MMIO region. So instead, detect such
regions at setup time and install the mappings for the backing all
at once.

Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Reviewed-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>

Now that we support read-only memslots, we need to make sure that
pass-through device mappings are not mapped writable if the guest
has requested them to be read-only. The existing implementation
already honours this by calling kvm_set_s2pte_writable() on the new
pte in case of writable mappings, so all we need to do is define
the default pgprot_t value used for devices to be PTE_S2_RDONLY.

Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>

Add support for read-only MMIO passthrough mappings by adding a
'writable' parameter to kvm_phys_addr_ioremap. For the moment,
mappings will be read-write even if 'writable' is false, but once
the definition of PAGE_S2_DEVICE gets changed, those mappings will
be created read-only.

Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>

Handle the potential NULL return value of find_vma_intersection()
before dereferencing it.

Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>

Pass __GFP_ZERO to __get_free_pages() instead of calling memset()
explicitly.

Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>

The different architectures used their own (and different) declarations:

    extern __visible const void __nosave_begin, __nosave_end;
    extern const void __nosave_begin, __nosave_end;
    extern long __nosave_begin, __nosave_end;

Consolidate them using the first variant in <asm/sections.h>.

Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Guan Xuetao <gxt@mprc.pku.edu.cn>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Activate the RCU fast_gup for ARM.  We also need to force THP splits to
broadcast an IPI s.t.  we block in the fast_gup page walker.  As THP
splits are comparatively rare, this should not lead to a noticeable
performance degradation.

Some pre-requisite functions pud_write and pud_page are also added.

Signed-off-by: Steve Capper <steve.capper@linaro.org>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Cc: Dann Frazier <dann.frazier@canonical.com>
Cc: Hugh Dickins <hughd@google.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Mel Gorman <mel@csn.ul.ie>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Christoffer Dall <christoffer.dall@linaro.org>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

In order to implement fast_get_user_pages we need to ensure that the page
table walker is protected from page table pages being freed from under it.

This patch enables HAVE_RCU_TABLE_FREE, any page table pages belonging to
address spaces with multiple users will be call_rcu_sched freed.  Meaning
that disabling interrupts will block the free and protect the fast gup
page walker.

Signed-off-by: Steve Capper <steve.capper@linaro.org>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Cc: Dann Frazier <dann.frazier@canonical.com>
Cc: Hugh Dickins <hughd@google.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Mel Gorman <mel@csn.ul.ie>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Christoffer Dall <christoffer.dall@linaro.org>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

We need a mechanism to tag ptes as being special, this indicates that no
attempt should be made to access the underlying struct page * associated
with the pte.  This is used by the fast_gup when operating on ptes as it
has no means to access VMAs (that also contain this information)
locklessly.

The L_PTE_SPECIAL bit is already allocated for LPAE, this patch modifies
pte_special and pte_mkspecial to make use of it, and defines
__HAVE_ARCH_PTE_SPECIAL.

This patch also excludes special ptes from the icache/dcache sync logic.

Signed-off-by: Steve Capper <steve.capper@linaro.org>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Cc: Dann Frazier <dann.frazier@canonical.com>
Cc: Hugh Dickins <hughd@google.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Mel Gorman <mel@csn.ul.ie>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Christoffer Dall <christoffer.dall@linaro.org>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>