B2000 board is reference board for STIH415/416 SOCs, it has
2 x UART, 4x USB, 2 x Ethernet, 1 x SATA, 1 x PCIe, and 1GB RAM.

This patch add initial support to b2000 with STiH415/416 with UART2 as
console and a heard beat LED.

Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@st.com>
CC: Stephen Gallimore <stephen.gallimore@st.com>
CC: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Olof Johansson <olof@lixom.net>

This patch adds low level debug uart support to sti based SOCs.

Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@st.com>
CC: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Olof Johansson <olof@lixom.net>

The STiH416 is advanced HD AVC processor with 3D graphics acceleration
and 1.2-GHz ARM Cortex-A9 SMP CPU.

Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@st.com>
CC: Stephen Gallimore <stephen.gallimore@st.com>
CC: Stuart Menefy <stuart.menefy@st.com>
CC: Arnd Bergmann <arnd@arndb.de>
CC: Linus Walleij <linus.walleij@linaro.org>

Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@st.com>
Signed-off-by: Olof Johansson <olof@lixom.net>

The STiH415 is the next generation of HD, AVC set-top box processors for
satellite, cable, terrestrial and IP-STB markets. It is an ARM Cortex-A9
1.0 GHz, dual-core CPU.

Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@st.com>
CC: Stephen Gallimore <stephen.gallimore@st.com>
CC: Stuart Menefy <stuart.menefy@st.com>
CC: Arnd Bergmann <arnd@arndb.de>
CC: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@st.com>
Signed-off-by: Olof Johansson <olof@lixom.net>

If the early MMU mapping of the UART happens to get booted out of the
TLB between the start of paging_init() and when we finally re-add the
UART at the very end of s3c_init_cpu(), we'll get a hang at bootup if
we've got early_printk enabled.  Avoid this hang by calling
debug_ll_io_init() early.

Without this patch, you can reliably reproduce a hang when early
printk is enabled by adding flush_tlb_all() at the start of
exynos_init_io().  After this patch the hang goes away.

Signed-off-by: Doug Anderson <dianders@chromium.org>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Olof Johansson <olof@lixom.net>

Printing low-level debug messages make an assumption that the specified
UART port has been preconfigured by the bootloader. Incorrectly
specified UART port results in system getting stalled while printing the
message "Uncompressing Linux... done, booting the kernel"
This UART port number is specified through S3C_LOWLEVEL_UART_PORT. Since
the UART port might different for different board, it is not possible to
specify it correctly for every board that use a common defconfig file.

Calling this print subroutine only when DEBUG_LL fixes the problem. By
disabling DEBUG_LL in default config file, we would be able to boot
multiple boards with different default UART ports.

With this current approach, we miss the print "Uncompressing Linux...
done, booting the kernel." when DEBUG_LL is not defined.

Signed-off-by: Tushar Behera <tushar.behera@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>

On RT5350 the memory size is set to Bytes and not MegaBytes due to a missing
multiplier.

Signed-off-by: John Crispin <blogic@openwrt.org>
Cc: John Crispin <blogic@openwrt.org>
Patchwork: https://patchwork.linux-mips.org/patch/5378/


Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

cputime_to_timeval() takes a struct timeval *as its second argument but
a struct compat_timeval * will be passed resulting in:

  CC      arch/mips/kernel/binfmt_elfn32.o
In file included from arch/mips/kernel/binfmt_elfn32.c:122:0:
arch/mips/kernel/../../../fs/binfmt_elf.c: In function ‘fill_prstatus’:
arch/mips/kernel/../../../fs/binfmt_elf.c:1330:3: warning: passing argument 2 of ‘cputime_to_timeval’ from incompatible pointer type [enabled by default]
In file included from include/asm-generic/cputime.h:12:0,
                 from /home/ralf/src/linux/linux-mips/arch/mips/include/asm/cputime.h:4,
                 from include/linux/sched.h:28,
                 from include/linux/ptrace.h:5,
                 from include/uapi/linux/elfcore.h:7,
                 from include/linux/elfcore.h:7,
                 from arch/mips/kernel/binfmt_elfn32.c:55:
include/asm-generic/cputime_nsecs.h:92:91: note: expected ‘struct timeval *’ but argument is of type ‘struct compat_timeval *’
In file included from arch/mips/kernel/binfmt_elfn32.c:122:0:
arch/mips/kernel/../../../fs/binfmt_elf.c:1331:3: warning: passing argument 2 of ‘cputime_to_timeval’ from incompatible pointer type [enabled by default]
In file included from include/asm-generic/cputime.h:12:0,
                 from /home/ralf/src/linux/linux-mips/arch/mips/include/asm/cputime.h:4,
                 from include/linux/sched.h:28,
                 from include/linux/ptrace.h:5,
                 from include/uapi/linux/elfcore.h:7,
                 from include/linux/elfcore.h:7,
                 from arch/mips/kernel/binfmt_elfn32.c:55:
include/asm-generic/cputime_nsecs.h:92:91: note: expected ‘struct timeval *’ but argument is of type ‘struct compat_timeval *’
In file included from arch/mips/kernel/binfmt_elfn32.c:122:0:
arch/mips/kernel/../../../fs/binfmt_elf.c:1336:3: warning: passing argument 2 of ‘cputime_to_timeval’ from incompatible pointer type [enabled by default]
In file included from include/asm-generic/cputime.h:12:0,
                 from /home/ralf/src/linux/linux-mips/arch/mips/include/asm/cputime.h:4,
                 from include/linux/sched.h:28,
                 from include/linux/ptrace.h:5,
                 from include/uapi/linux/elfcore.h:7,
                 from include/linux/elfcore.h:7,
                 from arch/mips/kernel/binfmt_elfn32.c:55:
include/asm-generic/cputime_nsecs.h:92:91: note: expected ‘struct timeval *’ but argument is of type ‘struct compat_timeval *’
In file included from arch/mips/kernel/binfmt_elfn32.c:122:0:
arch/mips/kernel/../../../fs/binfmt_elf.c:1337:3: warning: passing argument 2 of ‘cputime_to_timeval’ from incompatible pointer type [enabled by default]
In file included from include/asm-generic/cputime.h:12:0,
                 from /home/ralf/src/linux/linux-mips/arch/mips/include/asm/cputime.h:4,
                 from include/linux/sched.h:28,
                 from include/linux/ptrace.h:5,
                 from include/uapi/linux/elfcore.h:7,
                 from include/linux/elfcore.h:7,
                 from arch/mips/kernel/binfmt_elfn32.c:55:
include/asm-generic/cputime_nsecs.h:92:91: note: expected ‘struct timeval *’ but argument is of type ‘struct compat_timeval *’
In file included from arch/mips/kernel/binfmt_elfn32.c:122:0:
arch/mips/kernel/../../../fs/binfmt_elf.c:1339:2: warning: passing argument 2 of ‘cputime_to_timeval’ from incompatible pointer type [enabled by default]
In file included from include/asm-generic/cputime.h:12:0,
                 from /home/ralf/src/linux/linux-mips/arch/mips/include/asm/cputime.h:4,
                 from include/linux/sched.h:28,
                 from include/linux/ptrace.h:5,
                 from include/uapi/linux/elfcore.h:7,
                 from include/linux/elfcore.h:7,
                 from arch/mips/kernel/binfmt_elfn32.c:55:
include/asm-generic/cputime_nsecs.h:92:91: note: expected ‘struct timeval *’ but argument is of type ‘struct compat_timeval *’
In file included from arch/mips/kernel/binfmt_elfn32.c:122:0:
arch/mips/kernel/../../../fs/binfmt_elf.c:1340:2: warning: passing argument 2 of ‘cputime_to_timeval’ from incompatible pointer type [enabled by default]
In file included from include/asm-generic/cputime.h:12:0,
                 from /home/ralf/src/linux/linux-mips/arch/mips/include/asm/cputime.h:4,
                 from include/linux/sched.h:28,
                 from include/linux/ptrace.h:5,
                 from include/uapi/linux/elfcore.h:7,
                 from include/linux/elfcore.h:7,
                 from arch/mips/kernel/binfmt_elfn32.c:55:
include/asm-generic/cputime_nsecs.h:92:91: note: expected ‘struct timeval *’ but argument is of type ‘struct compat_timeval *’
  AS      arch/mips/kernel/scall64-n32.o
  CC      arch/mips/kernel/signal_n32.o
  CC      arch/mips/kernel/binfmt_elfo32.o
In file included from arch/mips/kernel/binfmt_elfo32.c:165:0:
arch/mips/kernel/../../../fs/binfmt_elf.c: In function ‘fill_prstatus’:
arch/mips/kernel/../../../fs/binfmt_elf.c:1330:3: warning: passing argument 2 of ‘cputime_to_timeval’ from incompatible pointer type [enabled by default]
In file included from include/asm-generic/cputime.h:12:0,
                 from /home/ralf/src/linux/linux-mips/arch/mips/include/asm/cputime.h:4,
                 from include/linux/sched.h:28,
                 from include/linux/ptrace.h:5,
                 from include/uapi/linux/elfcore.h:7,
                 from include/linux/elfcore.h:7,
                 from arch/mips/kernel/binfmt_elfo32.c:78:
include/asm-generic/cputime_nsecs.h:92:91: note: expected ‘struct timeval *’ but argument is of type ‘struct compat_timeval *’
In file included from arch/mips/kernel/binfmt_elfo32.c:165:0:
arch/mips/kernel/../../../fs/binfmt_elf.c:1331:3: warning: passing argument 2 of ‘cputime_to_timeval’ from incompatible pointer type [enabled by default]
In file included from include/asm-generic/cputime.h:12:0,
                 from /home/ralf/src/linux/linux-mips/arch/mips/include/asm/cputime.h:4,
                 from include/linux/sched.h:28,
                 from include/linux/ptrace.h:5,
                 from include/uapi/linux/elfcore.h:7,
                 from include/linux/elfcore.h:7,
                 from arch/mips/kernel/binfmt_elfo32.c:78:
include/asm-generic/cputime_nsecs.h:92:91: note: expected ‘struct timeval *’ but argument is of type ‘struct compat_timeval *’
In file included from arch/mips/kernel/binfmt_elfo32.c:165:0:
arch/mips/kernel/../../../fs/binfmt_elf.c:1336:3: warning: passing argument 2 of ‘cputime_to_timeval’ from incompatible pointer type [enabled by default]
In file included from include/asm-generic/cputime.h:12:0,
                 from /home/ralf/src/linux/linux-mips/arch/mips/include/asm/cputime.h:4,
                 from include/linux/sched.h:28,
                 from include/linux/ptrace.h:5,
                 from include/uapi/linux/elfcore.h:7,
                 from include/linux/elfcore.h:7,
                 from arch/mips/kernel/binfmt_elfo32.c:78:
include/asm-generic/cputime_nsecs.h:92:91: note: expected ‘struct timeval *’ but argument is of type ‘struct compat_timeval *’
In file included from arch/mips/kernel/binfmt_elfo32.c:165:0:
arch/mips/kernel/../../../fs/binfmt_elf.c:1337:3: warning: passing argument 2 of ‘cputime_to_timeval’ from incompatible pointer type [enabled by default]
In file included from include/asm-generic/cputime.h:12:0,
                 from /home/ralf/src/linux/linux-mips/arch/mips/include/asm/cputime.h:4,
                 from include/linux/sched.h:28,
                 from include/linux/ptrace.h:5,
                 from include/uapi/linux/elfcore.h:7,
                 from include/linux/elfcore.h:7,
                 from arch/mips/kernel/binfmt_elfo32.c:78:
include/asm-generic/cputime_nsecs.h:92:91: note: expected ‘struct timeval *’ but argument is of type ‘struct compat_timeval *’
In file included from arch/mips/kernel/binfmt_elfo32.c:165:0:
arch/mips/kernel/../../../fs/binfmt_elf.c:1339:2: warning: passing argument 2 of ‘cputime_to_timeval’ from incompatible pointer type [enabled by default]
In file included from include/asm-generic/cputime.h:12:0,
                 from /home/ralf/src/linux/linux-mips/arch/mips/include/asm/cputime.h:4,
                 from include/linux/sched.h:28,
                 from include/linux/ptrace.h:5,
                 from include/uapi/linux/elfcore.h:7,
                 from include/linux/elfcore.h:7,
                 from arch/mips/kernel/binfmt_elfo32.c:78:
include/asm-generic/cputime_nsecs.h:92:91: note: expected ‘struct timeval *’ but argument is of type ‘struct compat_timeval *’
In file included from arch/mips/kernel/binfmt_elfo32.c:165:0:
arch/mips/kernel/../../../fs/binfmt_elf.c:1340:2: warning: passing argument 2 of ‘cputime_to_timeval’ from incompatible pointer type [enabled by default]
In file included from include/asm-generic/cputime.h:12:0,
                 from /home/ralf/src/linux/linux-mips/arch/mips/include/asm/cputime.h:4,
                 from include/linux/sched.h:28,
                 from include/linux/ptrace.h:5,
                 from include/uapi/linux/elfcore.h:7,
                 from include/linux/elfcore.h:7,
                 from arch/mips/kernel/binfmt_elfo32.c:78:
include/asm-generic/cputime_nsecs.h:92:91: note: expected ‘struct timeval *’ but argument is of type ‘struct compat_timeval *’

Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

As noted by Wladislav Wiebe:
   $ halt
   ..
   Sent SIGKILL to all processes
   Requesting system halt
   [66.729373] System halted.
   [66.733244]
   [66.734761] =====================================
   [66.739473] [ BUG: lock held at task exit time! ]
   [66.744188] 3.8.7-0-sampleversion-fct #49 Tainted: G           O
   [66.750202] -------------------------------------
   [66.754913] init/21479 is exiting with locks still held!
   [66.760234] 1 lock held by init/21479:
   [66.763990]  #0:  (reboot_mutex){+.+...}, at: [<ffffffff801776c8>] SyS_reboot+0xe0/0x218
   [66.772165]
   [66.772165] stack backtrace:
   [66.776532] Call Trace:
   [66.778992] [<ffffffff805780a8>] dump_stack+0x8/0x34
   [66.783972] [<ffffffff801618b0>] do_exit+0x610/0xa70
   [66.788948] [<ffffffff801777a8>] SyS_reboot+0x1c0/0x218
   [66.794186] [<ffffffff8013d6a4>] handle_sys64+0x44/0x64

This is an alternative fix to the one sent by Wladislav.  We kill the
watchdog for each CPU and then spin in WAIT with interrupts disabled.
This is the lowest power mode for the OCTEON.  If we were to spin with
interrupts enabled, we would get a continual stream of warning messages
and backtraces from the lockup detector, so I chose to disable
interrupts.

Signed-off-by: David Daney <david.daney@cavium.com>
Cc: Maxim Uvarov <muvarov@gmail.com>
Cc: Wladislav Wiebe <wladislav.kw@gmail.com>
Cc: linux-mips@linux-mips.org
Cc: David Daney <david.daney@cavium.com>
Patchwork: https://patchwork.linux-mips.org/patch/5324/


Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

arch/mips/kernel/rtlx.c: In function 'rtlx_module_init':
arch/mips/kernel/rtlx.c:523:3: error: implicit declaration of function 'set_vi_handler' [-Werror=implicit-function-declaration]

Signed-off-by: Yoichi Yuasa <yuasa@linux-mips.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/5340/


Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

Since the introduction of preemptible mmu_gather TLB fast mode has been
broken. TLB fast mode relies on there being absolutely no concurrency;
it frees pages first and invalidates TLBs later.

However now we can get concurrency and stuff goes *bang*.

This patch removes all tlb_fast_mode() code; it was found the better
option vs trying to patch the hole by entangling tlb invalidation with
the scheduler.

Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Tony Luck <tony.luck@intel.com>
Reported-by: Max Filippov <jcmvbkbc@gmail.com>
Signed-off-by: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

f9a37be0 ("x86: Use PCI setup data") added support for using PCI ROM
images from setup_data.  This used phys_to_virt(), which is not valid for
highmem addresses, and can cause a crash when booting a 32-bit kernel via
the EFI boot stub.

pcibios_add_device() assumes that the physical addresses stored in
setup_data are accessible via the direct kernel mapping, and that calling
phys_to_virt() is valid.  This isn't guaranteed to be true on x86 where the
direct mapping range is much smaller than on x86-64.

Calling phys_to_virt() on a highmem address results in the following:

 BUG: unable to handle kernel paging request at 39a3c198
 IP: [<c262be0f>] pcibios_add_device+0x2f/0x90
 ...
 Call Trace:
  [<c2370c73>] pci_device_add+0xe3/0x130
  [<c274640b>] pci_scan_single_device+0x8b/0xb0
  [<c2370d08>] pci_scan_slot+0x48/0x100
  [<c2371904>] pci_scan_child_bus+0x24/0xc0
  [<c262a7b0>] pci_acpi_scan_root+0x2c0/0x490
  [<c23b7203>] acpi_pci_root_add+0x312/0x42f
  ...

The solution is to use ioremap() instead of phys_to_virt() to map the
setup data into the kernel address space.

[bhelgaas: changelog]
Tested-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Matt Fleming <matt.fleming@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Matthew Garrett <mjg59@srcf.ucam.org>
Cc: Seth Forshee <seth.forshee@canonical.com>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Cc: stable@vger.kernel.org	# v3.8+

Update the CMT clockevent rating from 125 to 80.

This resolves a boot-failure regression for kzm9g-reference in v3.10-rc1
introduced by f7db706b ("ARM: 7674/1: smp:
Avoid dummy clockevent being preferred over real").

The patch noted above reduces the rating of dummy clockevent from 400 to 100.
This patch reduces the rating of CMT so that it is once again less than that
of the dummy clockevent.

Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Using static inline functions ensure proper type checking
which also remove compilation warning for no MMU

Compilation warning:
arch/microblaze/include/asm/cacheflush.h: warning: 'addr'
 may be used uninitialized in this function [-Wmaybe-uninitialized]

Signed-off-by: Michal Simek <michal.simek@xilinx.com>

arch/microblaze/include/asm/uaccess.h:101:3:
 warning: cast removes address space of expression
arch/microblaze/include/asm/uaccess.h:107:2:
 warning: cast removes address space of expression

Signed-off-by: Michal Simek <michal.simek@xilinx.com>

apic->pending_events processing has a race that may cause INIT and
SIPI
processing to be reordered:

vpu0:                            vcpu1:
set INIT
                               test_and_clear_bit(KVM_APIC_INIT)
                                  process INIT
set INIT
set SIPI
                               test_and_clear_bit(KVM_APIC_SIPI)
                                  process SIPI

At the end INIT is left pending in pending_events. The following patch
fixes this by latching pending event before processing them.

Signed-off-by: Gleb Natapov <gleb@redhat.com>

The x86-64 extended low-byte registers were fetched correctly from reg,
but not from mod/rm.

This fixes another bug in the boot of RHEL5.9 64-bit, but it is still
not enough.

Cc: <stable@vger.kernel.org> # 3.9
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Gleb Natapov <gleb@redhat.com>

This is encountered when booting RHEL5.9 64-bit.  There is another bug
after this one that is not a simple emulation failure, but this one lets
the boot proceed a bit.

Cc: <stable@vger.kernel.org> # 3.9
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Gleb Natapov <gleb@redhat.com>

The KVM/ARM MMU code doesn't take care of invalidating TLBs before
freeing a {pte,pmd} table. This could cause problems if the page
is reallocated and then speculated into by another CPU.

Reported-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Christoffer Dall <cdall@cs.columbia.edu>

Some ARM KVM VCPU ioctls require the vCPU to be properly initialized
with the KVM_ARM_VCPU_INIT ioctl before being used with further
requests. KVM_RUN checks whether this initialization has been
done, but other ioctls do not.
Namely KVM_GET_REG_LIST will dereference an array with index -1
without initialization and thus leads to a kernel oops.
Fix this by adding checks before executing the ioctl handlers.

 [ Removed superflous comment from static function - Christoffer ]

Changes from v1:
 * moved check into a static function with a meaningful name

Signed-off-by: Andre Przywara <andre.przywara@linaro.org>
Signed-off-by: Christoffer Dall <cdall@cs.columbia.edu>

The Linux Way is to return -ENOIOCTLCMD to the vfs when an
unimplemented ioctl is requested.  Do this in kvm_mips instead of a
random mixture of -ENOTSUPP and -EINVAL.

Signed-off-by: David Daney <david.daney@cavium.com>
Acked-by: Sanjay Lal <sanjayl@kymasys.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>

Because not all 256 CP0 registers are ever implemented, we need a
different method of manipulating them.  Use the
KVM_SET_ONE_REG/KVM_GET_ONE_REG mechanism.

Now unused code and definitions are removed.

Signed-off-by: David Daney <david.daney@cavium.com>
Acked-by: Sanjay Lal <sanjayl@kymasys.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>

Also we cannot set special zero register, so force it to zero.

Signed-off-by: David Daney <david.daney@cavium.com>
Acked-by: Sanjay Lal <sanjayl@kymasys.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>

Signed-off-by: David Daney <david.daney@cavium.com>
Acked-by: Sanjay Lal <sanjayl@kymasys.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>

All registers are 64-bits wide, 32-bit guests use the least
significant portion of the register storage fields.

Signed-off-by: David Daney <david.daney@cavium.com>
Acked-by: Sanjay Lal <sanjayl@kymasys.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>

Define a non-empty struct kvm_fpu.

Signed-off-by: David Daney <david.daney@cavium.com>
Acked-by: Sanjay Lal <sanjayl@kymasys.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>

The AXI clock mux should be as below:

00: periph;
01: pll2_pfd2_396m;
10: periph;
11: pll3_pfd1_540m;

Signed-off-by: Anson Huang <b20788@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

Stephen Warren reported the recent commit 78506f22 (add support for
extended FIFO-size of PL011-r1p5) breaks the serial port on the
BCM2835 ARM SoC.

A UART compatible with the ARM PL011-r1p5 should have 32-deep FIFOs.
The BCM2835 UART just looks like an ARM PL011-r1p5, but has 16-deep
FIFOs just like PL011-r1p4 or earlier revisions. As a workaround for
this compatibility issue, this patch overrides the HW UART periphid
register values with the actually compatible UART periphid 0x00241011
(r1p3 or r1p4).

Reported-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Jongsung Kim <neidhard.kim@lge.com>
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Olof Johansson <olof@lixom.net>

'boot_args' is an input args, and 'boot_command_line' has a fix length.
So use strlcpy() instead of strcpy() to avoid memory overflow.

Signed-off-by: Chen Gang <gang.chen@asianux.com>
Acked-by: Kyle McMartin <kyle@mcmartin.ca>
Signed-off-by: Helge Deller <deller@gmx.de>

There's a Makefile line setting cflags for CONFIG_PA7100. But that
Kconfig macro doesn't exist. There is a Kconfig symbol PA7000, which
covers both PA7000 and PA7100 processors. So let's use the corresponding
Kconfig macro.

Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Helge Deller <deller@gmx.de>

With CONFIG_DISCONTIGMEM=y and multiple physical memory areas,
cat /proc/kpageflags triggers this kernel bug:

kernel BUG at arch/parisc/include/asm/mmzone.h:50!
CPU: 2 PID: 7848 Comm: cat Tainted: G      D W 3.10.0-rc3-64bit #44
 IAOQ[0]: kpageflags_read0x128/0x238
 IAOQ[1]: kpageflags_read0x12c/0x238
 RP(r2): proc_reg_read0xbc/0x130
Backtrace:
 [<00000000402ca2d4>] proc_reg_read0xbc/0x130
 [<0000000040235bcc>] vfs_read0xc4/0x1d0
 [<0000000040235f0c>] SyS_read0x94/0xf0
 [<0000000040105fc0>] syscall_exit0x0/0x14

kpageflags_read() walks through the whole memory, even if some memory
areas are physically not available. So, we should better not BUG on an
unavailable pfn in pfn_to_nid() but just return the expected value -1 or
0.

Signed-off-by: Helge Deller <deller@gmx.de>

'path.bc[i]' can be asigned by PCI_SLOT() which can '> 10', so sizeof(6
* "%u:" + "%u" + '\0') may be 21.

Since 'name' length is 20, it may be memory overflow.

And 'path.bc[i]' is 'unsigned char' for printing, we can be sure the
max length of 'name' must be less than 28.

So simplify thinking, we can use 28 instead of 20 directly, and do not
think of whether 'patchc.bc[i]' can '> 100'.

Signed-off-by: Chen Gang <gang.chen@asianux.com>
Signed-off-by: Helge Deller <deller@gmx.de>

Fix a typo in setting COMMON_USER2_POWER7 bits to .cpu_user_features2
cpu specs table.

Signed-off-by: Will Schmidt <will_schmidt@vnet.ibm.com>
Acked-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>

Commit 8f61aa32 "Add support for SIER" missed updates to siar_valid()
and perf_get_data_addr().

In both cases we need to check the SIER instead of mmcra.

Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>

This is a revert and then some of commit 860aad71 "Add regs_no_sipr()".
This workaround was only needed on early chip versions.

As before NO_SIPR becomes a static flag of the PMU struct.

Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>

The codes which ever used these two variables have gone. Throw away
them too.

Signed-off-by: Kevin Hao <haokexin@gmail.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>

These comments already don't apply to the current code. So just remove
them.

Signed-off-by: Kevin Hao <haokexin@gmail.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>

Adam Lackorzynski reported the following build failure on
!CONFIG_HOTPLUG_CPU configuration:

  CC      arch/powerpc/kernel/rtas.o
arch/powerpc/kernel/rtas.c: In function ‘rtas_cpu_state_change_mask’:
arch/powerpc/kernel/rtas.c:843:4: error: implicit declaration of function ‘cpu_down’ [-Werror=implicit-function-declaration]
cc1: all warnings being treated as errors
make[1]: *** [arch/powerpc/kernel/rtas.o] Error 1
make: *** [arch/powerpc/kernel] Error 2

The build fails because cpu_down() is defined only under CONFIG_HOTPLUG_CPU.

Looking further, the mobility code in pseries is one of the call-sites which
uses rtas_ibm_suspend_me(), which in turn calls rtas_cpu_state_change_mask().
And the mobility code is unconditionally compiled-in (it does not fall under
any Kconfig option). And commit 120496ac (powerpc: Bring all threads online
prior to migration/hibernation) which introduced this build regression is
critical for the proper functioning of the migration code. So it appears
that the only solution to this problem is to enable CONFIG_HOTPLUG_CPU if
SMP is enabled on PPC_PSERIES platforms. So make that change in the Kconfig.

Reported-by: Adam Lackorzynski <adam@os.inf.tu-dresden.de>
Cc: stable@vger.kernel.org
Signed-off-by: Srivatsa S. Bhat <srivatsa.bhat@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>

This adds the remaining two hypercalls defined by PAPR for manipulating
the XICS interrupt controller, H_IPOLL and H_XIRR_X.  H_IPOLL returns
information about the priority and pending interrupts for a virtual
cpu, without changing any state.  H_XIRR_X is like H_XIRR in that it
reads and acknowledges the highest-priority pending interrupt, but it
also returns the timestamp (timebase register value) from when the
interrupt was first received by the hypervisor.  Currently we just
return the current time, since we don't do any software queueing of
virtual interrupts inside the XICS emulation code.

These hcalls are not currently used by Linux guests, but may be in
future.

Signed-off-by: Paul Mackerras <paulus@samba.org>
Acked-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>

Commit a9c4e541
"powerpc/kprobe: Complete kprobe and migrate exception frame"
introduced a regression:

While returning from exception handling in case of PREEMPT enabled,
_TIF_NEED_RESCHED bit is checked in TI_FLAGS (thread_info flag) of current
task. Only if this bit is set, it should continue with the process of
calling preempt_schedule_irq() to schedule highest priority task if
available.

Current code assumes that r8 contains TI_FLAGS and check this for
_TIF_NEED_RESCHED, but as r8 is modified in the code which executes before
this check, r8 no longer contains the expected TI_FLAGS information.

As a result check for comparison with _TIF_NEED_RESCHED was failing even if
NEED_RESCHED bit is set in the current thread_info flag. Due to this,
preempt_schedule_irq() and in turn scheduler was not getting called even if
highest priority task is ready for execution.

So, store temporary results in r0 instead of r8 to prevent r8 from getting
modified as subsequent code is dependent on its value.

Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com>
CC: <stable@vger.kernel.org> [v3.7+]
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>