- Dec 01, 2021
-
-
Mark Rutland authored
[ Upstream commit dce1ca05 ] To hot unplug a CPU, the idle task on that CPU calls a few layers of C code before finally leaving the kernel. When KASAN is in use, poisoned shadow is left around for each of the active stack frames, and when shadow call stacks are in use. When shadow call stacks (SCS) are in use the task's saved SCS SP is left pointing at an arbitrary point within the task's shadow call stack. When a CPU is offlined than onlined back into the kernel, this stale state can adversely affect execution. Stale KASAN shadow can alias new stackframes and result in bogus KASAN warnings. A stale SCS SP is effectively a memory leak, and prevents a portion of the shadow call stack being used. Across a number of hotplug cycles the idle task's entire shadow call stack can become unusable. We previously fixed the KASAN issue in commit: e1b77c92 ("sched/kasan: remove stale KASAN poison after hotplug") ... by removing any stale KASAN stack poison immediately prior to onlining a CPU. Subsequently in commit: f1a0a376 ("sched/core: Initialize the idle task with preemption disabled") ... the refactoring left the KASAN and SCS cleanup in one-time idle thread initialization code rather than something invoked prior to each CPU being onlined, breaking both as above. We fixed SCS (but not KASAN) in commit: 63acd42c ("sched/scs: Reset the shadow stack when idle_task_exit") ... but as this runs in the context of the idle task being offlined it's potentially fragile. To fix these consistently and more robustly, reset the SCS SP and KASAN shadow of a CPU's idle task immediately before we online that CPU in bringup_cpu(). This ensures the idle task always has a consistent state when it is running, and removes the need to so so when exiting an idle task. Whenever any thread is created, dup_task_struct() will give the task a stack which is free of KASAN shadow, and initialize the task's SCS SP, so there's no need to specially initialize either for idle thread within init_idle(), as this was only necessary to handle hotplug cycles. I've tested this on arm64 with: * gcc 11.1.0, defconfig +KASAN_INLINE, KASAN_STACK * clang 12.0.0, defconfig +KASAN_INLINE, KASAN_STACK, SHADOW_CALL_STACK ... offlining and onlining CPUS with: | while true; do | for C in /sys/devices/system/cpu/cpu*/online; do | echo 0 > $C; | echo 1 > $C; | done | done Fixes: f1a0a376 ("sched/core: Initialize the idle task with preemption disabled") Reported-by: Qian Cai <quic_qiancai@quicinc.com> Signed-off-by: Mark Rutland <mark.rutland@arm.com> Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> Reviewed-by: Valentin Schneider <valentin.schneider@arm.com> Tested-by: Qian Cai <quic_qiancai@quicinc.com> Link: https://lore.kernel.org/lkml/20211115113310.35693-1-mark.rutland@arm.com/ Signed-off-by: Sasha Levin <sashal@kernel.org>
-
Arjun Roy authored
[ Upstream commit e0fecb28 ] A prior patch increased the size of struct tcp_zerocopy_receive but did not update do_tcp_getsockopt() handling to properly account for this. This patch simply reintroduces content erroneously cut from the referenced prior patch that handles the new struct size. Fixes: 18fb76ed ("net-zerocopy: Copy straggler unaligned data for TCP Rx. zerocopy.") Signed-off-by: Arjun Roy <arjunroy@google.com> Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: Soheil Hassas Yeganeh <soheil@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
-
Vladimir Oltean authored
[ Upstream commit c49a35ee ] The driver doesn't support RX timestamping for non-PTP packets, but it declares that it does. Restrict the reported RX filters to PTP v2 over L2 and over L4. Fixes: 4e3b0468 ("net: mscc: PTP Hardware Clock (PHC) support") Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
-
Vladimir Oltean authored
[ Upstream commit 8a075464 ] The ocelot driver, when asked to timestamp all receiving packets, 1588 v1 or NTP, says "nah, here's 1588 v2 for you". According to this discussion: https://patchwork.kernel.org/project/netdevbpf/patch/20211104133204.19757-8-martin.kaistra@linutronix.de/#24577647 drivers that downgrade from a wider request to a narrower response (or even a response where the intersection with the request is empty) are buggy, and should return -ERANGE instead. This patch fixes that. Fixes: 4e3b0468 ("net: mscc: PTP Hardware Clock (PHC) support") Suggested-by: Richard Cochran <richardcochran@gmail.com> Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Acked-by: Richard Cochran <richardcochran@gmail.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
-
Guangbin Huang authored
[ Upstream commit 8d2ad993 ] When PF is set to multi-TCs and configured mapping relationship between priorities and TCs, the hardware will active these settings for this PF and its VFs. In this case when VF just uses one TC and its rx packets contain priority, and if the priority is not mapped to TC0, as other TCs of VF is not valid, hardware always put this kind of packets to the queue 0. It cause this kind of packets of VF can not be used RSS function. To fix this problem, set tc mode of all unused TCs of VF to the setting of TC0, then rx packet with priority which map to unused TC will be direct to TC0. Fixes: e2cb1dec ("net: hns3: Add HNS3 VF HCL(Hardware Compatibility Layer) Support") Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
-
Tony Lu authored
[ Upstream commit bacb6c1e ] When applications call shutdown() with SHUT_RDWR in userspace, smc_close_active() calls kernel_sock_shutdown(), and it is called twice in smc_shutdown(). This fixes this by checking sk_state before do clcsock shutdown, and avoids missing the application's call of smc_shutdown(). Link: https://lore.kernel.org/linux-s390/1f67548e-cbf6-0dce-82b5-10288a4583bd@linux.ibm.com/ Fixes: 606a63c9 ("net/smc: Ensure the active closing peer first closes clcsock") Signed-off-by: Tony Lu <tonylu@linux.alibaba.com> Reviewed-by: Wen Gu <guwen@linux.alibaba.com> Acked-by: Karsten Graul <kgraul@linux.ibm.com> Link: https://lore.kernel.org/r/20211126024134.45693-1-tonylu@linux.alibaba.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
-
Ziyang Xuan authored
[ Upstream commit 01d9cc2d ] Inject error before dev_hold(real_dev) in register_vlan_dev(), and execute the following testcase: ip link add dev dummy1 type dummy ip link add name dummy1.100 link dummy1 type vlan id 100 ip link del dev dummy1 When the dummy netdevice is removed, we will get a WARNING as following: ======================================================================= refcount_t: decrement hit 0; leaking memory. WARNING: CPU: 2 PID: 0 at lib/refcount.c:31 refcount_warn_saturate+0xbf/0x1e0 and an endless loop of: ======================================================================= unregister_netdevice: waiting for dummy1 to become free. Usage count = -1073741824 That is because dev_put(real_dev) in vlan_dev_free() be called without dev_hold(real_dev) in register_vlan_dev(). It makes the refcnt of real_dev underflow. Move the dev_hold(real_dev) to vlan_dev_init() which is the call-back of ndo_init(). That makes dev_hold() and dev_put() for vlan's real_dev symmetrical. Fixes: 563bcbae ("net: vlan: fix a UAF in vlan_dev_real_dev()") Reported-by: Petr Machata <petrm@nvidia.com> Suggested-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Ziyang Xuan <william.xuanziyang@huawei.com> Link: https://lore.kernel.org/r/20211126015942.2918542-1-william.xuanziyang@huawei.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
-
Davide Caratti authored
[ Upstream commit de6d2592 ] when the number of DRR classes decreases, the round-robin active list can contain elements that have already been freed in ets_qdisc_change(). As a consequence, it's possible to see a NULL dereference crash, caused by the attempt to call cl->qdisc->ops->peek(cl->qdisc) when cl->qdisc is NULL: BUG: kernel NULL pointer dereference, address: 0000000000000018 #PF: supervisor read access in kernel mode #PF: error_code(0x0000) - not-present page PGD 0 P4D 0 Oops: 0000 [#1] PREEMPT SMP NOPTI CPU: 1 PID: 910 Comm: mausezahn Not tainted 5.16.0-rc1+ #475 Hardware name: Red Hat KVM, BIOS 1.11.1-4.module+el8.1.0+4066+0f1aadab 04/01/2014 RIP: 0010:ets_qdisc_dequeue+0x129/0x2c0 [sch_ets] Code: c5 01 41 39 ad e4 02 00 00 0f 87 18 ff ff ff 49 8b 85 c0 02 00 00 49 39 c4 0f 84 ba 00 00 00 49 8b ad c0 02 00 00 48 8b 7d 10 <48> 8b 47 18 48 8b 40 38 0f ae e8 ff d0 48 89 c3 48 85 c0 0f 84 9d RSP: 0000:ffffbb36c0b5fdd8 EFLAGS: 00010287 RAX: ffff956678efed30 RBX: 0000000000000000 RCX: 0000000000000000 RDX: 0000000000000002 RSI: ffffffff9b938dc9 RDI: 0000000000000000 RBP: ffff956678efed30 R08: e2f3207fe360129c R09: 0000000000000000 R10: 0000000000000001 R11: 0000000000000001 R12: ffff956678efeac0 R13: ffff956678efe800 R14: ffff956611545000 R15: ffff95667ac8f100 FS: 00007f2aa9120740(0000) GS:ffff95667b800000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 0000000000000018 CR3: 000000011070c000 CR4: 0000000000350ee0 Call Trace: <TASK> qdisc_peek_dequeued+0x29/0x70 [sch_ets] tbf_dequeue+0x22/0x260 [sch_tbf] __qdisc_run+0x7f/0x630 net_tx_action+0x290/0x4c0 __do_softirq+0xee/0x4f8 irq_exit_rcu+0xf4/0x130 sysvec_apic_timer_interrupt+0x52/0xc0 asm_sysvec_apic_timer_interrupt+0x12/0x20 RIP: 0033:0x7f2aa7fc9ad4 Code: b9 ff ff 48 8b 54 24 18 48 83 c4 08 48 89 ee 48 89 df 5b 5d e9 ed fc ff ff 0f 1f 00 66 2e 0f 1f 84 00 00 00 00 00 f3 0f 1e fa <53> 48 83 ec 10 48 8b 05 10 64 33 00 48 8b 00 48 85 c0 0f 85 84 00 RSP: 002b:00007ffe5d33fab8 EFLAGS: 00000202 RAX: 0000000000000002 RBX: 0000561f72c31460 RCX: 0000561f72c31720 RDX: 0000000000000002 RSI: 0000561f72c31722 RDI: 0000561f72c31720 RBP: 000000000000002a R08: 00007ffe5d33fa40 R09: 0000000000000014 R10: 0000000000000000 R11: 0000000000000246 R12: 0000561f7187e380 R13: 0000000000000000 R14: 0000000000000000 R15: 0000561f72c31460 </TASK> Modules linked in: sch_ets sch_tbf dummy rfkill iTCO_wdt intel_rapl_msr iTCO_vendor_support intel_rapl_common joydev virtio_balloon lpc_ich i2c_i801 i2c_smbus pcspkr ip_tables xfs libcrc32c crct10dif_pclmul crc32_pclmul crc32c_intel ahci libahci ghash_clmulni_intel serio_raw libata virtio_blk virtio_console virtio_net net_failover failover sunrpc dm_mirror dm_region_hash dm_log dm_mod CR2: 0000000000000018 Ensuring that 'alist' was never zeroed [1] was not sufficient, we need to remove from the active list those elements that are no more SP nor DRR. [1] https://lore.kernel.org/netdev/60d274838bf09777f0371253416e8af71360bc08.1633609148.git.dcaratti@redhat.com/ v3: fix race between ets_qdisc_change() and ets_qdisc_dequeue() delisting DRR classes beyond 'nbands' in ets_qdisc_change() with the qdisc lock acquired, thanks to Cong Wang. v2: when a NULL qdisc is found in the DRR active list, try to dequeue skb from the next list item. Reported-by: Hangbin Liu <liuhangbin@gmail.com> Fixes: dcc68b4d ("net: sch_ets: Add a new Qdisc") Signed-off-by: Davide Caratti <dcaratti@redhat.com> Link: https://lore.kernel.org/r/7a5c496eed2d62241620bdbb83eb03fb9d571c99.1637762721.git.dcaratti@redhat.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
-
Jakub Kicinski authored
[ Upstream commit f3911f73 ] We replace proto_ops whenever TLS is configured for RX. But our replacement also overrides sendpage_locked, which will crash unless TX is also configured. Similarly we plug both of those in for TLS_HW (NIC crypto offload) even tho TLS_HW has a completely different implementation for TX. Last but not least we always plug in something based on inet_stream_ops even though a few of the callbacks differ for IPv6 (getname, release, bind). Use a callback building method similar to what we do for struct proto. Fixes: c46234eb ("tls: RX path for ktls") Fixes: d4ffb02d ("net/tls: enable sk_msg redirect to tls socket egress") Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
-
Jakub Kicinski authored
[ Upstream commit 520493f6 ] We don't support splicing control records. TLS 1.3 changes moved the record type check into the decrypt if(). The skb may already be decrypted and still be an alert. Note that decrypt_skb_update() is idempotent and updates ctx->decrypted so the if() is pointless. Reorder the check for decryption errors with the content type check while touching them. This part is not really a bug, because if decryption failed in TLS 1.3 content type will be DATA, and for TLS 1.2 it will be correct. Nevertheless its strange to touch output before checking if the function has failed. Fixes: fedf201e ("net: tls: Refactor control message handling on recv") Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
-
Huang Pei authored
[ Upstream commit 41ce097f ] It hangup when booting Loongson 3A1000 with BOTH CONFIG_PAGE_SIZE_64KB and CONFIG_MIPS_VA_BITS_48, that it turn out to use 2-level pgtable instead of 3-level. 64KB page size with 2-level pgtable only cover 42 bits VA, use 3-level pgtable to cover all 48 bits VA(55 bits) Fixes: 1e321fa9 ("MIPS64: Support of at least 48 bits of SEGBITS) Signed-off-by: Huang Pei <huangpei@loongson.cn> Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
-
Huang Pei authored
[ Upstream commit 7db5e9e9 ] It turns out that 'decode_configs' -> 'set_ftlb_enable' is called under c->cputype unset, which leaves FTLB disabled on BOTH 3A2000 and 3A3000 Fix it by calling "decode_configs" after c->cputype is initialized Fixes: da1bd297 ("MIPS: Loongson64: Probe CPU features via CPUCFG") Signed-off-by: Huang Pei <huangpei@loongson.cn> Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
-
Jesse Brandeburg authored
[ Upstream commit eaeace60 ] Oleksandr brought a bug report where netpoll causes trace messages in the log on igb. Danielle brought this back up as still occurring, so we'll try again. [22038.710800] ------------[ cut here ]------------ [22038.710801] igb_poll+0x0/0x1440 [igb] exceeded budget in poll [22038.710802] WARNING: CPU: 12 PID: 40362 at net/core/netpoll.c:155 netpoll_poll_dev+0x18a/0x1a0 As Alex suggested, change the driver to return work_done at the exit of napi_poll, which should be safe to do in this driver because it is not polling multiple queues in this single napi context (multiple queues attached to one MSI-X vector). Several other drivers contain the same simple sequence, so I hope this will not create new problems. Fixes: 16eb8815 ("igb: Refactor clean_rx_irq to reduce overhead and improve performance") Reported-by: Oleksandr Natalenko <oleksandr@natalenko.name> Reported-by: Danielle Ratson <danieller@nvidia.com> Suggested-by: Alexander Duyck <alexander.duyck@gmail.com> Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com> Tested-by: Oleksandr Natalenko <oleksandr@natalenko.name> Tested-by: Danielle Ratson <danieller@nvidia.com> Link: https://lore.kernel.org/r/20211123204000.1597971-1-jesse.brandeburg@intel.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
-
Maurizio Lombardi authored
[ Upstream commit c024b226 ] Submit I/O requests with the IOCB_NOWAIT flag set only if the underlying filesystem supports it. Fixes: 50a909db ("nvmet: use IOCB_NOWAIT for file-ns buffered I/O") Signed-off-by: Maurizio Lombardi <mlombard@redhat.com> Reviewed-by: Chaitanya Kulkarni <kch@nvidia.com> Signed-off-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
-
Guo DaXing authored
[ Upstream commit 9ebb0c4b ] The kernel_listen function in smc_listen will fail when all the available ports are occupied. At this point smc->clcsock->sk->sk_data_ready has been changed to smc_clcsock_data_ready. When we call smc_listen again, now both smc->clcsock->sk->sk_data_ready and smc->clcsk_data_ready point to the smc_clcsock_data_ready function. The smc_clcsock_data_ready() function calls lsmc->clcsk_data_ready which now points to itself resulting in an infinite loop. This patch restores smc->clcsock->sk->sk_data_ready with the old value. Fixes: a60a2b1e ("net/smc: reduce active tcp_listen workers") Signed-off-by: Guo DaXing <guodaxing@huawei.com> Acked-by: Tony Lu <tonylu@linux.alibaba.com> Signed-off-by: Karsten Graul <kgraul@linux.ibm.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
-
Karsten Graul authored
[ Upstream commit 587acad4 ] Coverity reports a possible NULL dereferencing problem: in smc_vlan_by_tcpsk(): 6. returned_null: netdev_lower_get_next returns NULL (checked 29 out of 30 times). 7. var_assigned: Assigning: ndev = NULL return value from netdev_lower_get_next. 1623 ndev = (struct net_device *)netdev_lower_get_next(ndev, &lower); CID 1468509 (#1 of 1): Dereference null return value (NULL_RETURNS) 8. dereference: Dereferencing a pointer that might be NULL ndev when calling is_vlan_dev. 1624 if (is_vlan_dev(ndev)) { Remove the manual implementation and use netdev_walk_all_lower_dev() to iterate over the lower devices. While on it remove an obsolete function parameter comment. Fixes: cb9d43f6 ("net/smc: determine vlan_id of stacked net_device") Suggested-by: Julian Wiedmann <jwi@linux.ibm.com> Signed-off-by: Karsten Graul <kgraul@linux.ibm.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
-
Russell King (Oracle) authored
[ Upstream commit dbae3388 ] On mv88e6xxx 1G/2.5G PCS, the SerDes register 4.2001.2 has the following description: This register bit indicates when link was lost since the last read. For the current link status, read this register back-to-back. Thus to get current link state, we need to read the register twice. But doing that in the link change interrupt handler would lead to potentially ignoring link down events, which we really want to avoid. Thus this needs to be solved in phylink's resolve, by retriggering another resolve in the event when PCS reports link down and previous link was up, and by re-reading PCS state if the previous link was down. The wrong value is read when phylink requests change from sgmii to 2500base-x mode, and link won't come up. This fixes the bug. Fixes: 9525ae83 ("phylink: add phylink infrastructure") Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk> Signed-off-by: Marek Behún <kabel@kernel.org> Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
-
Russell King (Oracle) authored
[ Upstream commit 80662f4f ] On PHY state change the phylink_resolve() function can read stale information from the MAC and report incorrect link speed and duplex to the kernel message log. Example with a Marvell 88X3310 PHY connected to a SerDes port on Marvell 88E6393X switch: - PHY driver triggers state change due to PHY interface mode being changed from 10gbase-r to 2500base-x due to copper change in speed from 10Gbps to 2.5Gbps, but the PHY itself either hasn't yet changed its interface to the host, or the interrupt about loss of SerDes link hadn't arrived yet (there can be a delay of several milliseconds for this), so we still think that the 10gbase-r mode is up - phylink_resolve() - phylink_mac_pcs_get_state() - this fills in speed=10g link=up - interface mode is updated to 2500base-x but speed is left at 10Gbps - phylink_major_config() - interface is changed to 2500base-x - phylink_link_up() - mv88e6xxx_mac_link_up() - .port_set_speed_duplex() - speed is set to 10Gbps - reports "Link is Up - 10Gbps/Full" to dmesg Afterwards when the interrupt finally arrives for mv88e6xxx, another resolve is forced in which we get the correct speed from phylink_mac_pcs_get_state(), but since the interface is not being changed anymore, we don't call phylink_major_config() but only phylink_mac_config(), which does not set speed/duplex anymore. To fix this, we need to force the link down and trigger another resolve on PHY interface change event. Fixes: 9525ae83 ("phylink: add phylink infrastructure") Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk> Signed-off-by: Marek Behún <kabel@kernel.org> Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
-
Heiner Kallweit authored
[ Upstream commit ddb826c2 ] Usage of phy_ethtool_get_link_ksettings() in the link status change handler isn't needed, and in combination with the referenced change it results in a deadlock. Simply remove the call and replace it with direct access to phydev->speed. The duplex argument of lan743x_phy_update_flowcontrol() isn't used and can be removed. Fixes: c10a485c ("phy: phy_ethtool_ksettings_get: Lock the phy for consistency") Reported-by: Alessandro B Maurici <abmaurici@gmail.com> Tested-by: Alessandro B Maurici <abmaurici@gmail.com> Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Link: https://lore.kernel.org/r/40e27f76-0ba3-dcef-ee32-a78b9df38b0f@gmail.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
-
Eric Dumazet authored
[ Upstream commit 4e1fddc9 ] While testing BIG TCP patch series, I was expecting that TCP_RR workloads with 80KB requests/answers would send one 80KB TSO packet, then being received as a single GRO packet. It turns out this was not happening, and the root cause was that cubic Hystart ACK train was triggering after a few (2 or 3) rounds of RPC. Hystart was wrongly setting CWND/SSTHRESH to 30, while my RPC needed a budget of ~20 segments. Ideally these TCP_RR flows should not exit slow start. Cubic Hystart should reset itself at each round, instead of assuming every TCP flow is a bulk one. Note that even after this patch, Hystart can still trigger, depending on scheduling artifacts, but at a higher CWND/SSTHRESH threshold, keeping optimal TSO packet sizes. Tested: ip link set dev eth0 gro_ipv6_max_size 131072 gso_ipv6_max_size 131072 nstat -n; netperf -H ... -t TCP_RR -l 5 -- -r 80000,80000 -K cubic; nstat|egrep "Ip6InReceives|Hystart|Ip6OutRequests" Before: 8605 Ip6InReceives 87541 0.0 Ip6OutRequests 129496 0.0 TcpExtTCPHystartTrainDetect 1 0.0 TcpExtTCPHystartTrainCwnd 30 0.0 After: 8760 Ip6InReceives 88514 0.0 Ip6OutRequests 87975 0.0 Fixes: ae27e98a ("[TCP] CUBIC v2.3") Co-developed-by: Neal Cardwell <ncardwell@google.com> Signed-off-by: Neal Cardwell <ncardwell@google.com> Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: Stephen Hemminger <stephen@networkplumber.org> Cc: Yuchung Cheng <ycheng@google.com> Cc: Soheil Hassas Yeganeh <soheil@google.com> Link: https://lore.kernel.org/r/20211123202535.1843771-1-eric.dumazet@gmail.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
-
Nicholas Kazlauskas authored
[ Upstream commit 21431f70 ] [Why] We're only setting the flags on stream[0]'s planes so this logic fails if we have more than one stream in the state. This can cause a page flip timeout with multiple displays in the configuration. [How] Index into the stream_status array using the stream index - it's a 1:1 mapping. Fixes: cdaae837 ("drm/amd/display: Handle GPU reset for DC block") Reviewed-by: Harry Wentland <Harry.Wentland@amd.com> Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com> Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com> Tested-by: Daniel Wheeler <daniel.wheeler@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
-
Thomas Zeitlhofer authored
[ Upstream commit cefcf24b ] Commit 39fbef4b ("PM: hibernate: Get block device exclusively in swsusp_check()") changed the opening mode of the block device to (FMODE_READ | FMODE_EXCL). In the corresponding calls to swsusp_close(), the mode is still just FMODE_READ which triggers the warning in blkdev_flush_mapping() on resume from hibernate. So, use the mode (FMODE_READ | FMODE_EXCL) also when closing the device. Fixes: 39fbef4b ("PM: hibernate: Get block device exclusively in swsusp_check()") Signed-off-by: Thomas Zeitlhofer <thomas.zeitlhofer+lkml@ze-it.at> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
-
Kumar Thangavel authored
[ Upstream commit ac132852 ] Update NC-SI command handler (both standard and OEM) to take into account of payload paddings in allocating skb (in case of payload size is not 32-bit aligned). The checksum field follows payload field, without taking payload padding into account can cause checksum being truncated, leading to dropped packets. Fixes: fb4ee675 ("net/ncsi: Add NCSI OEM command support") Signed-off-by: Kumar Thangavel <thangavel.k@hcl.com> Acked-by: Samuel Mendoza-Jonas <sam@mendozajonas.com> Reviewed-by: Paul Menzel <pmenzel@molgen.mpg.de> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
-
Varun Prakash authored
[ Upstream commit 102110ef ] Current nvmet_try_send_ddgst() code does not check whether all data digest bytes are transmitted, fix this by returning -EAGAIN if all data digest bytes are not transmitted. Fixes: 872d26a3 ("nvmet-tcp: add NVMe over TCP target driver") Signed-off-by: Varun Prakash <varun@chelsio.com> Reviewed-by: Sagi Grimberg <sagi@grimberg.me> Signed-off-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
-
Marek Behún authored
[ Upstream commit 7b1b62bc ] Currently mvpp2_xdp_setup won't allow attaching XDP program if mtu > ETH_DATA_LEN (1500). The mvpp2_change_mtu on the other hand checks whether MVPP2_RX_PKT_SIZE(mtu) > MVPP2_BM_LONG_PKT_SIZE. These two checks are semantically different. Moreover this limit can be increased to MVPP2_MAX_RX_BUF_SIZE, since in mvpp2_rx we have xdp.data = data + MVPP2_MH_SIZE + MVPP2_SKB_HEADROOM; xdp.frame_sz = PAGE_SIZE; Change the checks to check whether mtu > MVPP2_MAX_RX_BUF_SIZE Fixes: 07dd0a7a ("mvpp2: add basic XDP support") Signed-off-by: Marek Behún <kabel@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
-
Amit Cohen authored
[ Upstream commit 63b08b1f ] When processing port up/down events generated by the device's firmware, the driver protects itself from events reported for non-existent local ports, but not the CPU port (local port 0), which exists, but lacks a netdev. This can result in a NULL pointer dereference when calling netif_carrier_{on,off}(). Fix this by bailing early when processing an event reported for the CPU port. Problem was only observed when running on top of a buggy emulator. Fixes: 28b1987e ("mlxsw: spectrum: Register CPU port with devlink") Signed-off-by: Amit Cohen <amcohen@nvidia.com> Signed-off-by: Ido Schimmel <idosch@nvidia.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
-
Danielle Ratson authored
[ Upstream commit 837ec05c ] There are few cases in which an array index queried from a fw register, is accessed without any validation that it doesn't exceed the array length. Add a proper length validation, so accessing memory past the end of an array will be forbidden. Signed-off-by: Danielle Ratson <danieller@nvidia.com> Signed-off-by: Ido Schimmel <idosch@nvidia.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
-
Tony Lu authored
[ Upstream commit 606a63c9 ] The side that actively closed socket, it's clcsock doesn't enter TIME_WAIT state, but the passive side does it. It should show the same behavior as TCP sockets. Consider this, when client actively closes the socket, the clcsock in server enters TIME_WAIT state, which means the address is occupied and won't be reused before TIME_WAIT dismissing. If we restarted server, the service would be unavailable for a long time. To solve this issue, shutdown the clcsock in [A], perform the TCP active close progress first, before the passive closed side closing it. So that the actively closed side enters TIME_WAIT, not the passive one. Client | Server close() // client actively close | smc_release() | smc_close_active() // PEERCLOSEWAIT1 | smc_close_final() // abort or closed = 1| smc_cdc_get_slot_and_msg_send() | [A] | |smc_cdc_msg_recv_action() // ACTIVE | queue_work(smc_close_wq, &conn->close_work) | smc_close_passive_work() // PROCESSABORT or APPCLOSEWAIT1 | smc_close_passive_abort_received() // only in abort | |close() // server recv zero, close | smc_release() // PROCESSABORT or APPCLOSEWAIT1 | smc_close_active() | smc_close_abort() or smc_close_final() // CLOSED | smc_cdc_get_slot_and_msg_send() // abort or closed = 1 smc_cdc_msg_recv_action() | smc_clcsock_release() queue_work(smc_close_wq, &conn->close_work) | sock_release(tcp) // actively close clc, enter TIME_WAIT smc_close_passive_work() // PEERCLOSEWAIT1 | smc_conn_free() smc_close_passive_abort_received() // CLOSED| smc_conn_free() | smc_clcsock_release() | sock_release(tcp) // passive close clc | Link: https://www.spinics.net/lists/netdev/msg780407.html Fixes: b38d7324 ("smc: socket closing and linkgroup cleanup") Signed-off-by: Tony Lu <tonylu@linux.alibaba.com> Reviewed-by: Wen Gu <guwen@linux.alibaba.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
-
Huang Jianan authored
[ Upstream commit 57bbeacd ] We observed the following deadlock in the stress test under low memory scenario: Thread A Thread B - erofs_shrink_scan - erofs_try_to_release_workgroup - erofs_workgroup_try_to_freeze -- A - z_erofs_do_read_page - z_erofs_collection_begin - z_erofs_register_collection - erofs_insert_workgroup - xa_lock(&sbi->managed_pslots) -- B - erofs_workgroup_get - erofs_wait_on_workgroup_freezed -- A - xa_erase - xa_lock(&sbi->managed_pslots) -- B To fix this, it needs to hold xa_lock before freezing the workgroup since xarray will be touched then. So let's hold the lock before accessing each workgroup, just like what we did with the radix tree before. [ Gao Xiang: Jianhua Hao also reports this issue at https://lore.kernel.org/r/b10b85df30694bac8aadfe43537c897a@xiaomi.com ] Link: https://lore.kernel.org/r/20211118135844.3559-1-huangjianan@oppo.com Fixes: 64094a04 ("erofs: convert workstn to XArray") Reviewed-by: Chao Yu <chao@kernel.org> Reviewed-by: Gao Xiang <hsiangkao@linux.alibaba.com> Signed-off-by: Huang Jianan <huangjianan@oppo.com> Reported-by: Jianhua Hao <haojianhua1@xiaomi.com> Signed-off-by: Gao Xiang <xiang@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
-
Shin'ichiro Kawasaki authored
[ Upstream commit 2d62253e ] When a reset is requested the position of the write pointer is updated but the data in the corresponding zone is not cleared. Instead scsi_debug returns any data written before the write pointer was reset. This is an error and prevents using scsi_debug for stale page cache testing of the BLKRESETZONE ioctl. Zero written data in the zone when resetting the write pointer. Link: https://lore.kernel.org/r/20211122061223.298890-1-shinichiro.kawasaki@wdc.com Fixes: f0d1cf93 ("scsi: scsi_debug: Add ZBC zone commands") Reviewed-by: Damien Le Moal <damien.lemoal@opensource.wdc.com> Acked-by: Douglas Gilbert <dgilbert@interlog.com> Signed-off-by: Shin'ichiro Kawasaki <shinichiro.kawasaki@wdc.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
-
Mike Christie authored
[ Upstream commit eb97545d ] This fixes an issue added in commit 4edd8cd4 ("scsi: core: sysfs: Fix hang when device state is set via sysfs") where if userspace is requesting to set the device state to SDEV_RUNNING when the state is already SDEV_RUNNING, we return -EINVAL instead of count. The commmit above set ret to count for this case, when it should have set it to 0. Link: https://lore.kernel.org/r/20211120164917.4924-1-michael.christie@oracle.com Fixes: 4edd8cd4 ("scsi: core: sysfs: Fix hang when device state is set via sysfs") Reviewed-by: Lee Duncan <lduncan@suse.com> Signed-off-by: Mike Christie <michael.christie@oracle.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
-
Marta Plantykow authored
[ Upstream commit f65ee535 ] Ice driver has the routines for managing XDP resources that are shared between ndo_bpf op and VSI rebuild flow. The latter takes place for example when user changes queue count on an interface via ethtool's set_channels(). There is an issue around the bpf_prog refcounting when VSI is being rebuilt - since ice_prepare_xdp_rings() is called with vsi->xdp_prog as an argument that is used later on by ice_vsi_assign_bpf_prog(), same bpf_prog pointers are swapped with each other. Then it is also interpreted as an 'old_prog' which in turn causes us to call bpf_prog_put on it that will decrement its refcount. Below splat can be interpreted in a way that due to zero refcount of a bpf_prog it is wiped out from the system while kernel still tries to refer to it: [ 481.069429] BUG: unable to handle page fault for address: ffffc9000640f038 [ 481.077390] #PF: supervisor read access in kernel mode [ 481.083335] #PF: error_code(0x0000) - not-present page [ 481.089276] PGD 100000067 P4D 100000067 PUD 1001cb067 PMD 106d2b067 PTE 0 [ 481.097141] Oops: 0000 [#1] PREEMPT SMP PTI [ 481.101980] CPU: 12 PID: 3339 Comm: sudo Tainted: G OE 5.15.0-rc5+ #1 [ 481.110840] Hardware name: Intel Corp. GRANTLEY/GRANTLEY, BIOS GRRFCRB1.86B.0276.D07.1605190235 05/19/2016 [ 481.122021] RIP: 0010:dev_xdp_prog_id+0x25/0x40 [ 481.127265] Code: 80 00 00 00 00 0f 1f 44 00 00 89 f6 48 c1 e6 04 48 01 fe 48 8b 86 98 08 00 00 48 85 c0 74 13 48 8b 50 18 31 c0 48 85 d2 74 07 <48> 8b 42 38 8b 40 20 c3 48 8b 96 90 08 00 00 eb e8 66 2e 0f 1f 84 [ 481.148991] RSP: 0018:ffffc90007b63868 EFLAGS: 00010286 [ 481.155034] RAX: 0000000000000000 RBX: ffff889080824000 RCX: 0000000000000000 [ 481.163278] RDX: ffffc9000640f000 RSI: ffff889080824010 RDI: ffff889080824000 [ 481.171527] RBP: ffff888107af7d00 R08: 0000000000000000 R09: ffff88810db5f6e0 [ 481.179776] R10: 0000000000000000 R11: ffff8890885b9988 R12: ffff88810db5f4bc [ 481.188026] R13: 0000000000000000 R14: 0000000000000000 R15: 0000000000000000 [ 481.196276] FS: 00007f5466d5bec0(0000) GS:ffff88903fb00000(0000) knlGS:0000000000000000 [ 481.205633] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [ 481.212279] CR2: ffffc9000640f038 CR3: 000000014429c006 CR4: 00000000003706e0 [ 481.220530] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 [ 481.228771] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 [ 481.237029] Call Trace: [ 481.239856] rtnl_fill_ifinfo+0x768/0x12e0 [ 481.244602] rtnl_dump_ifinfo+0x525/0x650 [ 481.249246] ? __alloc_skb+0xa5/0x280 [ 481.253484] netlink_dump+0x168/0x3c0 [ 481.257725] netlink_recvmsg+0x21e/0x3e0 [ 481.262263] ____sys_recvmsg+0x87/0x170 [ 481.266707] ? __might_fault+0x20/0x30 [ 481.271046] ? _copy_from_user+0x66/0xa0 [ 481.275591] ? iovec_from_user+0xf6/0x1c0 [ 481.280226] ___sys_recvmsg+0x82/0x100 [ 481.284566] ? sock_sendmsg+0x5e/0x60 [ 481.288791] ? __sys_sendto+0xee/0x150 [ 481.293129] __sys_recvmsg+0x56/0xa0 [ 481.297267] do_syscall_64+0x3b/0xc0 [ 481.301395] entry_SYSCALL_64_after_hwframe+0x44/0xae [ 481.307238] RIP: 0033:0x7f5466f39617 [ 481.311373] Code: 0c 00 f7 d8 64 89 02 48 c7 c0 ff ff ff ff eb bd 0f 1f 00 f3 0f 1e fa 64 8b 04 25 18 00 00 00 85 c0 75 10 b8 2f 00 00 00 0f 05 <48> 3d 00 f0 ff ff 77 51 c3 48 83 ec 28 89 54 24 1c 48 89 74 24 10 [ 481.342944] RSP: 002b:00007ffedc7f4308 EFLAGS: 00000246 ORIG_RAX: 000000000000002f [ 481.361783] RAX: ffffffffffffffda RBX: 00007ffedc7f5460 RCX: 00007f5466f39617 [ 481.380278] RDX: 0000000000000000 RSI: 00007ffedc7f5360 RDI: 0000000000000003 [ 481.398500] RBP: 00007ffedc7f53f0 R08: 0000000000000000 R09: 000055d556f04d50 [ 481.416463] R10: 0000000000000077 R11: 0000000000000246 R12: 00007ffedc7f5360 [ 481.434131] R13: 00007ffedc7f5350 R14: 00007ffedc7f5344 R15: 0000000000000e98 [ 481.451520] Modules linked in: ice(OE) af_packet binfmt_misc nls_iso8859_1 ipmi_ssif intel_rapl_msr intel_rapl_common x86_pkg_temp_thermal intel_powerclamp mxm_wmi mei_me coretemp mei ipmi_si ipmi_msghandler wmi acpi_pad acpi_power_meter ip_tables x_tables autofs4 crct10dif_pclmul crc32_pclmul ghash_clmulni_intel aesni_intel ahci crypto_simd cryptd libahci lpc_ich [last unloaded: ice] [ 481.528558] CR2: ffffc9000640f038 [ 481.542041] ---[ end trace d1f24c9ecf5b61c1 ]--- Fix this by only calling ice_vsi_assign_bpf_prog() inside ice_prepare_xdp_rings() when current vsi->xdp_prog pointer is NULL. This way set_channels() flow will not attempt to swap the vsi->xdp_prog pointers with itself. Also, sprinkle around some comments that provide a reasoning about correlation between driver and kernel in terms of bpf_prog refcount. Fixes: efc2214b ("ice: Add support for XDP") Reviewed-by: Alexander Lobakin <alexandr.lobakin@intel.com> Signed-off-by: Marta Plantykow <marta.a.plantykow@intel.com> Co-developed-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com> Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com> Tested-by: Kiran Bhandare <kiranx.bhandare@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
-
Maciej Fijalkowski authored
[ Upstream commit 792b2086 ] The approach of having XDP queue per CPU regardless of user's setting exposed a hidden bug that could occur in case when Rx queue count differ from Tx queue count. Currently vsi->txq_map's size is equal to the doubled vsi->alloc_txq, which is not correct due to the fact that XDP rings were previously based on the Rx queue count. Below splat can be seen when ethtool -L is used and XDP rings are configured: [ 682.875339] BUG: kernel NULL pointer dereference, address: 000000000000000f [ 682.883403] #PF: supervisor read access in kernel mode [ 682.889345] #PF: error_code(0x0000) - not-present page [ 682.895289] PGD 0 P4D 0 [ 682.898218] Oops: 0000 [#1] PREEMPT SMP PTI [ 682.903055] CPU: 42 PID: 2878 Comm: ethtool Tainted: G OE 5.15.0-rc5+ #1 [ 682.912214] Hardware name: Intel Corp. GRANTLEY/GRANTLEY, BIOS GRRFCRB1.86B.0276.D07.1605190235 05/19/2016 [ 682.923380] RIP: 0010:devres_remove+0x44/0x130 [ 682.928527] Code: 49 89 f4 55 48 89 fd 4c 89 ff 53 48 83 ec 10 e8 92 b9 49 00 48 8b 9d a8 02 00 00 48 8d 8d a0 02 00 00 49 89 c2 48 39 cb 74 0f <4c> 3b 63 10 74 25 48 8b 5b 08 48 39 cb 75 f1 4c 89 ff 4c 89 d6 e8 [ 682.950237] RSP: 0018:ffffc90006a679f0 EFLAGS: 00010002 [ 682.956285] RAX: 0000000000000286 RBX: ffffffffffffffff RCX: ffff88908343a370 [ 682.964538] RDX: 0000000000000001 RSI: ffffffff81690d60 RDI: 0000000000000000 [ 682.972789] RBP: ffff88908343a0d0 R08: 0000000000000000 R09: 0000000000000000 [ 682.981040] R10: 0000000000000286 R11: 3fffffffffffffff R12: ffffffff81690d60 [ 682.989282] R13: ffffffff81690a00 R14: ffff8890819807a8 R15: ffff88908343a36c [ 682.997535] FS: 00007f08c7bfa740(0000) GS:ffff88a03fd00000(0000) knlGS:0000000000000000 [ 683.006910] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [ 683.013557] CR2: 000000000000000f CR3: 0000001080a66003 CR4: 00000000003706e0 [ 683.021819] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 [ 683.030075] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 [ 683.038336] Call Trace: [ 683.041167] devm_kfree+0x33/0x50 [ 683.045004] ice_vsi_free_arrays+0x5e/0xc0 [ice] [ 683.050380] ice_vsi_rebuild+0x4c8/0x750 [ice] [ 683.055543] ice_vsi_recfg_qs+0x9a/0x110 [ice] [ 683.060697] ice_set_channels+0x14f/0x290 [ice] [ 683.065962] ethnl_set_channels+0x333/0x3f0 [ 683.070807] genl_family_rcv_msg_doit+0xea/0x150 [ 683.076152] genl_rcv_msg+0xde/0x1d0 [ 683.080289] ? channels_prepare_data+0x60/0x60 [ 683.085432] ? genl_get_cmd+0xd0/0xd0 [ 683.089667] netlink_rcv_skb+0x50/0xf0 [ 683.094006] genl_rcv+0x24/0x40 [ 683.097638] netlink_unicast+0x239/0x340 [ 683.102177] netlink_sendmsg+0x22e/0x470 [ 683.106717] sock_sendmsg+0x5e/0x60 [ 683.110756] __sys_sendto+0xee/0x150 [ 683.114894] ? handle_mm_fault+0xd0/0x2a0 [ 683.119535] ? do_user_addr_fault+0x1f3/0x690 [ 683.134173] __x64_sys_sendto+0x25/0x30 [ 683.148231] do_syscall_64+0x3b/0xc0 [ 683.161992] entry_SYSCALL_64_after_hwframe+0x44/0xae Fix this by taking into account the value that num_possible_cpus() yields in addition to vsi->alloc_txq instead of doubling the latter. Fixes: efc2214b ("ice: Add support for XDP") Fixes: 22bf877e ("ice: introduce XDP_TX fallback path") Reviewed-by: Alexander Lobakin <alexandr.lobakin@intel.com> Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com> Tested-by: Kiran Bhandare <kiranx.bhandare@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
-
Nikolay Aleksandrov authored
[ Upstream commit 1005f19b ] When replacing a nexthop group, we must release the IPv6 per-cpu dsts of the removed nexthop entries after an RCU grace period because they contain references to the nexthop's net device and to the fib6 info. With specific series of events[1] we can reach net device refcount imbalance which is unrecoverable. IPv4 is not affected because dsts don't take a refcount on the route. [1] $ ip nexthop list id 200 via 2002:db8::2 dev bridge.10 scope link onlink id 201 via 2002:db8::3 dev bridge scope link onlink id 203 group 201/200 $ ip -6 route 2001:db8::10 nhid 203 metric 1024 pref medium nexthop via 2002:db8::3 dev bridge weight 1 onlink nexthop via 2002:db8::2 dev bridge.10 weight 1 onlink Create rt6_info through one of the multipath legs, e.g.: $ taskset -a -c 1 ./pkt_inj 24 bridge.10 2001:db8::10 (pkt_inj is just a custom packet generator, nothing special) Then remove that leg from the group by replace (let's assume it is id 200 in this case): $ ip nexthop replace id 203 group 201 Now remove the IPv6 route: $ ip -6 route del 2001:db8::10/128 The route won't be really deleted due to the stale rt6_info holding 1 refcnt in nexthop id 200. At this point we have the following reference count dependency: (deleted) IPv6 route holds 1 reference over nhid 203 nh 203 holds 1 ref over id 201 nh 200 holds 1 ref over the net device and the route due to the stale rt6_info Now to create circular dependency between nh 200 and the IPv6 route, and also to get a reference over nh 200, restore nhid 200 in the group: $ ip nexthop replace id 203 group 201/200 And now we have a permanent circular dependncy because nhid 203 holds a reference over nh 200 and 201, but the route holds a ref over nh 203 and is deleted. To trigger the bug just delete the group (nhid 203): $ ip nexthop del id 203 It won't really be deleted due to the IPv6 route dependency, and now we have 2 unlinked and deleted objects that reference each other: the group and the IPv6 route. Since the group drops the reference it holds over its entries at free time (i.e. its own refcount needs to drop to 0) that will never happen and we get a permanent ref on them, since one of the entries holds a reference over the IPv6 route it will also never be released. At this point the dependencies are: (deleted, only unlinked) IPv6 route holds reference over group nh 203 (deleted, only unlinked) group nh 203 holds reference over nh 201 and 200 nh 200 holds 1 ref over the net device and the route due to the stale rt6_info This is the last point where it can be fixed by running traffic through nh 200, and specifically through the same CPU so the rt6_info (dst) will get released due to the IPv6 genid, that in turn will free the IPv6 route, which in turn will free the ref count over the group nh 203. If nh 200 is deleted at this point, it will never be released due to the ref from the unlinked group 203, it will only be unlinked: $ ip nexthop del id 200 $ ip nexthop $ Now we can never release that stale rt6_info, we have IPv6 route with ref over group nh 203, group nh 203 with ref over nh 200 and 201, nh 200 with rt6_info (dst) with ref over the net device and the IPv6 route. All of these objects are only unlinked, and cannot be released, thus they can't release their ref counts. Message from syslogd@dev at Nov 19 14:04:10 ... kernel:[73501.828730] unregister_netdevice: waiting for bridge.10 to become free. Usage count = 3 Message from syslogd@dev at Nov 19 14:04:20 ... kernel:[73512.068811] unregister_netdevice: waiting for bridge.10 to become free. Usage count = 3 Fixes: 7bf4796d ("nexthops: add support for replace") Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
-
Nikolay Aleksandrov authored
[ Upstream commit 8837cbbf ] We need a way to release a fib6_nh's per-cpu dsts when replacing nexthops otherwise we can end up with stale per-cpu dsts which hold net device references, so add a new IPv6 stub called fib6_nh_release_dsts. It must be used after an RCU grace period, so no new dsts can be created through a group's nexthop entry. Similar to fib6_nh_release it shouldn't be used if fib6_nh_init has failed so it doesn't need a dummy stub when IPv6 is not enabled. Fixes: 7bf4796d ("nexthops: add support for replace") Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
-
Holger Assmann authored
[ Upstream commit a6da2bbb ] Currently, when user space emits SIOCSHWTSTAMP ioctl calls such as enabling/disabling timestamping or changing filter settings, the driver reads the current CLOCK_REALTIME value and programming this into the NIC's hardware clock. This might be necessary during system initialization, but at runtime, when the PTP clock has already been synchronized to a grandmaster, a reset of the timestamp settings might result in a clock jump. Furthermore, if the clock is also controlled by phc2sys in automatic mode (where the UTC offset is queried from ptp4l), that UTC-to-TAI offset (currently 37 seconds in 2021) would be temporarily reset to 0, and it would take a long time for phc2sys to readjust so that CLOCK_REALTIME and the PHC are apart by 37 seconds again. To address the issue, we introduce a new function called stmmac_init_tstamp_counter(), which gets called during ndo_open(). It contains the code snippet moved from stmmac_hwtstamp_set() that manages the time synchronization. Besides, the sub second increment configuration is also moved here since the related values are hardware dependent and runtime invariant. Furthermore, the hardware clock must be kept running even when no time stamping mode is selected in order to retain the synchronized time base. That way, timestamping can be enabled again at any time only with the need to compensate the clock's natural drifting. As a side effect, this patch fixes the issue that ptp_clock_info::enable can be called before SIOCSHWTSTAMP and the driver (which looks at priv->systime_flags) was not prepared to handle that ordering. Fixes: 92ba6888 ("stmmac: add the support for PTP hw clock driver") Reported-by: Michael Olbrich <m.olbrich@pengutronix.de> Signed-off-by: Ahmad Fatoum <a.fatoum@pengutronix.de> Signed-off-by: Holger Assmann <h.assmann@pengutronix.de> Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
-
Joakim Zhang authored
[ Upstream commit 276aae37 ] commit 5f585913 ("net: stmmac: delete the eee_ctrl_timer after napi disabled"), this patch tries to fix system hang caused by eee_ctrl_timer, unfortunately, it only can resolve it for system reboot stress test. System hang also can be reproduced easily during system suspend/resume stess test when mount NFS on i.MX8MP EVK board. In stmmac driver, eee feature is combined to phylink framework. When do system suspend, phylink_stop() would queue delayed work, it invokes stmmac_mac_link_down(), where to deactivate eee_ctrl_timer synchronizly. In above commit, try to fix issue by deactivating eee_ctrl_timer obviously, but it is not enough. Looking into eee_ctrl_timer expire callback stmmac_eee_ctrl_timer(), it could enable hareware eee mode again. What is unexpected is that LPI interrupt (MAC_Interrupt_Enable.LPIEN bit) is always asserted. This interrupt has chance to be issued when LPI state entry/exit from the MAC, and at that time, clock could have been already disabled. The result is that system hang when driver try to touch register from interrupt handler. The reason why above commit can fix system hang issue in stmmac_release() is that, deactivate eee_ctrl_timer not just after napi disabled, further after irq freed. In conclusion, hardware would generate LPI interrupt when clock has been disabled during suspend or resume, since hardware is in eee mode and LPI interrupt enabled. Interrupts from MAC, MTL and DMA level are enabled and never been disabled when system suspend, so postpone clocks management from suspend stage to noirq suspend stage should be more safe. Fixes: 5f585913 ("net: stmmac: delete the eee_ctrl_timer after napi disabled") Signed-off-by: Joakim Zhang <qiangqing.zhang@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
-
Diana Wang authored
[ Upstream commit 3bd6b2a8 ] Use nn->tlv_caps.me_freq_mhz instead of nn->me_freq_mhz to check whether rx-usecs/tx-usecs is valid. This is because nn->tlv_caps.me_freq_mhz represents the clock_freq (MHz) of the flow processing cores (FPC) on the NIC. While nn->me_freq_mhz is not be set. Fixes: ce991ab6 ("nfp: read ME frequency from vNIC ctrl memory") Signed-off-by: Diana Wang <na.wang@corigine.com> Signed-off-by: Simon Horman <simon.horman@corigine.com> Reviewed-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
-
Eric Dumazet authored
[ Upstream commit 19d36c5f ] We deal with IPv6 packets, so we need to use IP6CB(skb)->flags and IP6SKB_REROUTED, instead of IPCB(skb)->flags and IPSKB_REROUTED Found by code inspection, please double check that fixing this bug does not surface other bugs. Fixes: 09ee9dba ("ipv6: Reinject IPv6 packets if IPsec policy matches after SNAT") Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: Tobias Brunner <tobias@strongswan.org> Cc: Steffen Klassert <steffen.klassert@secunet.com> Cc: David Ahern <dsahern@kernel.org> Reviewed-by: David Ahern <dsahern@kernel.org> Tested-by: Tobias Brunner <tobias@strongswan.org> Acked-by: Tobias Brunner <tobias@strongswan.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
-
Michael Kelley authored
[ Upstream commit e95d8eae ] The ARCH_FEATURES function ID is a 32-bit SMC call, which returns a 32-bit result per the SMCCC spec. Current code is doing a 64-bit comparison against -1 (SMCCC_RET_NOT_SUPPORTED) to detect that the feature is unimplemented. That check doesn't work in a Hyper-V VM, where the upper 32-bits are zero as allowed by the spec. Cast the result as an 'int' so the comparison works. The change also makes the code consistent with other similar checks in this file. Fixes: 821b67fa ("firmware: smccc: Add ARCH_SOC_ID support") Signed-off-by: Michael Kelley <mikelley@microsoft.com> Reviewed-by: Sudeep Holla <sudeep.holla@arm.com> Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
-