The Orange Pi Plus is a SBC based on the Allwinner H3 SoC
with 8GB eMMC, multiple USB ports through a USB hub chip, SATA through
a USB-SATA bridge, one uSD slot, a 10/100/1000M ethernet port,
WiFi, HDMI, headphone jack, IR receiver, a microphone, a CSI connector
and a 40-pin GPIO header.

Signed-off-by: Jens Kuske <jenskuske@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

The Allwinner H3 is a home entertainment system oriented SoC with
four Cortex-A7 cores and a Mali-400MP2 GPU.

Signed-off-by: Jens Kuske <jenskuske@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

The DRAM gates controls direct memory access for some peripherals.
These peripherals include the display pipeline, so add the required
gates to the simplefb nodes as well.

Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

The DRAM gates controls direct memory access for some peripherals.
These peripherals include the display pipeline, so add the required
gates to the simplefb nodes as well.

Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

The Allwinner A80 SoC has an NMI controller. NMI is an external
interrupt pin exclusely used with PMICs and other system critical
peripherals (such as RTC) in Allwinner's reference designs.

Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

This patch adds a device node for the Reduced Serial Bus (RSB)
controller and the defacto pinmux setting to the A80 dtsi.

Since there is only one possible pinmux setting for RSB, just
set it in the dtsi.

Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

The A80 Optimus board has a consumer IR receiver. Enable it in the DT.

Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

The Allwinner A80 SoC has a consumer IR receiver, which is the same as
older SoCs.

Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

LED3 is connected to pin PM15 on R_PIO.

Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

The A80 has a secondary pin controller. Add a device node for it.

Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

The main (24MHz) clock on the A80 is configurable via the PRCM address
space. The low power/speed (32kHz) clock is from an external chip, the
AC100.

Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

This adds the supported PRCM clocks and reset controls to the A80 dtsi.
The DAUDIO module clocks are not supported yet.

Also update clock and reset phandles for r_uart.

Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

Add a node describing the touchscreen found on the pov protab2-ips9
tablet.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

Add a node describing the touchscreen controller used on the iNet1 tablet.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

Enable the on-chip audio codec

Signed-off-by: Stefan Monnier <monnier@iro.umontreal.ca>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

Enable the on-chip audio codec

Signed-off-by: Stefan Monnier <monnier@iro.umontreal.ca>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

Add a node describing the AXP152 pmic used on Auxtek T004 boards.

Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Michael van Slingerland <michael@deviousops.nl>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

Add a node describing the lcd panel backlight on the pov protab2 ips9
tablet.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

Add a node describing the lcd panel backlight on the UTOO P66 tablet.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

Add a node describing the lcd panel backlight on the iNet1 tablet.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

The iNet1 tablet uses the A10's integrated audio codec, enable it.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

Some boards, such as tablets, have regulators providing power to parts
of the display pipeline, like signal converters and LCD panels.

Add labels to the simplefb device nodes so that we can reference them
in the board dts files to add regulator supply properties.

Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

Gemei G9 has internal speakers and headphone jack. Audio switching
from internal speakers to headphones is automatically handled by
extra FT2012Q audio amplifier chip that works out of the box.

Signed-off-by: Priit Laes <plaes@plaes.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

ADC seems to be using ldo2 for reference voltage.

Signed-off-by: Priit Laes <plaes@plaes.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

Add regulator nodes for axp209 using the axp209.dtsi include.

Signed-off-by: Priit Laes <plaes@plaes.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

The inet9f-rev03 tablet has multiple fire-buttons / direction controls,
add support for these using the same axis mapping as ps2 compatible game
controllers with the same stick / button layout use.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

Enable the on-chip audio codec

Signed-off-by: Jelle van der Waa <jelle@vdwaa.nl>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

Enable on-chip audio codec on the Wexler TAB7200 tablet.

Signed-off-by: Aleksei Mamlin <mamlinav@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

Enable the on-chip audio codec on the Olimex A20-SOM-EVB

Signed-off-by: Marcus Weseloh <mweseloh42@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

Enable the axp221 PMIC chip in the dts file.

Allows board to power off correctly from the poweroff command

This board requires dc1sw to be enabled in order to provide a power source
for the 5V DCDC converter that powers USB2.

This board uses dldo1 for 3.3V wifi power

This board requires dldo3 to be enabled at 2.8V in order to provide voltage
to the pullup resistors for the i2c0 bus.

Signed-off-by: Lawrence Yu <lyu@micile.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

This baseboard from SWAC is equipped with the ICnova-A20 SoM from
Incircuit. This board is equipped with the following interfaces /
devices:

- 512 MiB SDRAM
- 4 GiB MLC NAND (Micron MT29F32G08CBACAWP or Hynix H27UBG8T2BTR)
- USB host
- LCD 800x480
- HDMI
- CAN

Note that the NAND support is still missing. As its currently not
supported in mainline for sunxi and especially for these MLC
devices.

The original plan was to also provide a dtsi for the ICnova SoM,
to put all the SoM internal nodes / properties there. But as I
don't have a clear overview of the SoM specific and baseboard
specific differences, I'm putting all in one dts for now. Once
somebody pushed support for some other baseboard using the
A20 SoM from Incircuit (e.g. the ADB4006 reference design), this
should be separated.

Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Marcus Heuer <marcus.heuer@swac.de>
[maxime: Fixed CPU regulator upper voltage boundary]
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

The pcDuino V3 Nano has a 3.5mm TRRS jack socket for audio, using the
CTIA standard pinout, connected to HPOUTL, HPOUTR, HPCOM/HPCOMFB and
MICIN1/VMIC (via appropriate RC networks) on the A20. The PH00 GPIO is
wired for headphone plug detection: it reads 0 when nothing's plugged
in, and 1 when a plug is inserted.

LINEINL/R and FMINL/R are not connected.

Signed-off-by: Adam Sampson <ats@offog.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

This reverts commit af19161a,
which breaks the omap3 device tree build due to a wrong reference.

I accidently queued this change via the power supply subsystem while
telling Marek at the same time, that it should go through Tony.
Following that I did miss Stephen's messages about the build failure in
linux-next and since he switched to merging an older snapshot nobody
else noticed the problem in my tree. I didn't notice myself, since I
did not build any device tree files assuming none have changed by me.

Signed-off-by: Sebastian Reichel <sre@kernel.org>
Reported-by: Felipe Balbi <balbi@ti.com>
Tested-by: Felipe Balbi <balbi@ti.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Tested-by: Kevin Hilman <khilman@linaro.org>
Acked-by: Tony Lindgren <tony@atomide.com>

This patch adds DT entries for the LEDs found on the Kirkwood-based
LaCie boards 2Big and 5Big Network v2.

Signed-off-by: Simon Guinot <simon.guinot@sequanux.org>
Acked-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>

This reverts commit d871cd2e as it causes
regression in BBB

Reported-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>

This reverts commit e3faf2b8 as it causes
regression in BBB

Reported-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>

The System Bus Controller block has two register regions,
but having only the second one in a separate node was not nice.

Replace it with a new node with two register regions in it.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Olof Johansson <olof@lixom.net>

Enable building all dtb files when CONFIG_OF_ALL_DTBS is enabled. The dtbs
are not really dependent on a platform being enabled or any other kernel
config, so for testing coverage it is convenient to build all of the dtbs.
This builds all dts files in the tree, not just targets listed. This
is simpler for arm64 which has a bunch of sub-dirs.

Signed-off-by: Rob Herring <robh@kernel.org>
Cc: Russell King <linux@arm.linux.org.uk>

Switch to use the ti,edma3-tpcc and ti,edma3-tptc binding for the eDMA3 and
enable the DMA even crossbar with ti,am335x-edma-crossbar.
With the new bindings boards can customize and tweak the DMA channel
priority to match their needs. With the new binding the memcpy is safe
to be used since with the old binding it was not possible for a driver
to know which channel is allowed to be used as non HW triggered channel.

Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>