When auditing cmpxchg call sites, Chuck noted that gcc was optimizing
away some of the desired LDs.

|	do {
|		new = old = *ipi_data_ptr;
|		new |= 1U << msg;
|	} while (cmpxchg(ipi_data_ptr, old, new) != old);

was generating to below

| 8015cef8:	ld         r2,[r4,0]  <-- First LD
| 8015cefc:	bset       r1,r2,r1
|
| 8015cf00:	llock      r3,[r4]  <-- atomic op
| 8015cf04:	brne       r3,r2,8015cf10
| 8015cf08:	scond      r1,[r4]
| 8015cf0c:	bnz        8015cf00
|
| 8015cf10:	brne       r3,r2,8015cf00  <-- Branch doesn't go to orig LD

Although this was fixed by adding a ACCESS_ONCE in this call site, it
seems safer (for now at least) to add compiler barrier to LLSC based
cmpxchg

Reported-by: Chuck Jordan <cjordan@synopsys,com>
Cc: <stable@vger.kernel.org>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>

Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>

Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>

- Handle possible interrupt coalescing from MCIP
- chk if prev IPI ack before sending new

Signed-off-by: Vineet Gupta <vgupta@synopsys.com>

Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>

This allows platforms to provide their own cpu wakeup routines
as well as IPI send / clear backends, while allowing a SMP kernel w/o
any such backend to build/boot

Signed-off-by: Vineet Gupta <vgupta@synopsys.com>

Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>

Signed-off-by: Vineet Gupta <vgupta@synopsys.com>

Branch insn can't be scheduled as last insn of Zero Overhead loop

Signed-off-by: Vineet Gupta <vgupta@synopsys.com>

Signed-off-by: Vineet Gupta <vgupta@synopsys.com>

This is also default for AXS103 release

Signed-off-by: Vineet Gupta <vgupta@synopsys.com>

Caveats about cache flush on ARCv2 based cores

- dcache is PIPT so paddr is sufficient for cache maintenance ops (no
  need to setup PTAG reg

- icache is still VIPT but only aliasing configs need PTAG setup

So basically this is departure from MMU-v3 which always need vaddr in
line ops registers (DC_IVDL, DC_FLDL, IC_IVIL) but paddr in DC_PTAG,
IC_PTAG respectively.

Signed-off-by: Vineet Gupta <vgupta@synopsys.com>

Signed-off-by: Vineet Gupta <vgupta@synopsys.com>

The issue was, on HS when interrupt is taken, IRQ_ACT is set and that is
NOT cleared unless we do RTIE (or manually clear it). Linux interrupt
handling has top and bottom halves. Latter lead to softirqs (which can
reschedule) AND expect interrupts to be REALLY re-enabled which was NOT
happening for us since we only SETI, dont clear IRQ_ACT

So we can have a state when both cores have taken interrupt (IRQ_ACT set),
get rescheduled, both send IPI and wait in CSD lock which will never be
cleared as cores can't take the pending IPI IRQ due to existing IRQ_ACT
set.

So local_irq_enable() now drops the IRQ_ACT.act bit to re-enable IRQs.

Signed-off-by: Vineet Gupta <vgupta@synopsys.com>

Reported by Anton as LTP:munmap01 failing with Illegal Instruction
Exception.

   --------------------->8--------------------------------------
   mmap2(NULL, 24576, PROT_READ|PROT_WRITE, MAP_SHARED, 3, 0) = 0x200d2000
   munmap(0x200d2000, 24576)               = 0
   --- SIGSEGV {si_signo=SIGSEGV, si_code=SEGV_MAPERR, si_addr=0x200d2000}
   ---
   potentially unexpected fatal signal 4.
   Path: /munmap01
   CPU: 0 PID: 61 Comm: munmap01 Not tainted 3.13.0-g5d5c46d9a556 #8
   task: 9f1a8000 ti: 9f154000 task.ti: 9f154000

   [ECR   ]: 0x00020100 => Illegal Insn
   [EFA   ]: 0x0001354c
   [BLINK ]: 0x200515d4
   [ERET  ]: 0x1354c
       @off 0x1354c in [/munmap01]
       VMA: 0x00010000 to 0x00018000
   [STAT32]: 0x800802c0
   ...
   --------------------->8--------------------------------------

The issue was
1. munmap01 accessed unmapped memory (on purpose) with signal handler
   installed for SIGSEGV

2. The faulting instruction happened to be in Delay Slot
   00011864 <main>:
      11908:	bl.d       13284 <tst_resm>
      1190c:	stb        r16,[r2]

3. kernel sets up the reg file for signal handler and correctly clears
   the DE bit in pt_regs->status32 placeholder

4. However RESTORE_CALLEE_SAVED_USER macro is not adjusted for ARCv2,
   and it over-writes the above with orig/stale value of status32

5. After RTIE, userspace signal handler executes a non branch
   instruction with DE bit set, triggering Illegal Instruction Exception.

Reported-by: Anton Kolesov <akolesov@synopsys.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>

Signed-off-by: Vineet Gupta <vgupta@synopsys.com>

The notable features are:
    - SMP configurations of upto 4 cores with coherency
    - Optional L2 Cache and IO-Coherency
    - Revised Interrupt Architecture (multiple priorites, reg banks,
        auto stack switch, auto regfile save/restore)
    - MMUv4 (PIPT dcache, Huge Pages)
    - Instructions for
	* 64bit load/store: LDD, STD
	* Hardware assisted divide/remainder: DIV, REM
	* Function prologue/epilogue: ENTER_S, LEAVE_S
	* IRQ enable/disable: CLRI, SETI
	* pop count: FFS, FLS
	* SETcc, BMSKN, XBFU...

Signed-off-by: Vineet Gupta <vgupta@synopsys.com>

Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>

ioremap already uses the hard define, just make sure BCR value matches
that

Signed-off-by: Vineet Gupta <vgupta@synopsys.com>

Signed-off-by: Vineet Gupta <vgupta@synopsys.com>

These have been register compatible so far. However ARCv2 mandates
different pt_regs layout (due to h/w auto save). To keep pt_regs same
for both, we start by removing the assumption - used mainly for block
copies between the 2 structs in signal handling and ptrace

Signed-off-by: Vineet Gupta <vgupta@synopsys.com>

Previously this macro was overloaded with stack switching, saving SP at right
slot in pt_regs, saving/setup of r25 and setting SP baseline to where
pt_regs->sp is saved (vs. bottom of pt_regs)

Now it only does SP switch, and leaves SP pointing to bottom of pt_regs.

r25 saving is no longer done here to allow for future reordering of
regfile in pt_regs w/o touching this macro

Signed-off-by: Vineet Gupta <vgupta@synopsys.com>

Returning from pure kernel mode and exception mode use the same code
anyways. Remove one the duplicate blocks

Signed-off-by: Vineet Gupta <vgupta@synopsys.com>

Elide the need to re-read ECR in Trap handler by ensuring that
EXCEPTION_PROLOGUE does that at the very end just before returning
to Trap handler

ARCv2 EXCEPTION_PROLOGUE already did that, so same for ARcompact and the
common trap handler adjusted to use cached ECR

Signed-off-by: Vineet Gupta <vgupta@synopsys.com>

Signed-off-by: Vineet Gupta <vgupta@synopsys.com>

Signed-off-by: Vineet Gupta <vgupta@synopsys.com>

This fixes the possible link/relo errors, since restore_regs will be
provided by ISA code, but called from ARC common code.
The .L prefix reassures binutils that it will be in same compilation
unit.

Signed-off-by: Vineet Gupta <vgupta@synopsys.com>

Signed-off-by: Vineet Gupta <vgupta@synopsys.com>

Signed-off-by: Vineet Gupta <vgupta@synopsys.com>

Signed-off-by: Vineet Gupta <vgupta@synopsys.com>

Signed-off-by: Vineet Gupta <vgupta@synopsys.com>

-EXCEPTION_EPILOGUE introduced
-EXCEPTION_PROLOGUE now also includes reg file saving

Signed-off-by: Vineet Gupta <vgupta@synopsys.com>

-common'ize macros for level 1 and level 2 interrupts

Signed-off-by: Vineet Gupta <vgupta@synopsys.com>

Signed-off-by: Vineet Gupta <vgupta@synopsys.com>

- Remove the ifdef'ery and write distinct versions for each mmu ver even
  if there is some code duplication

Signed-off-by: Vineet Gupta <vgupta@synopsys.com>

That is because __after_dc_op() already reads it for status check, so it
is better anyways to use that "newer" value.

Also reduces the clutter in callers for passing from/to these routines.

Signed-off-by: Vineet Gupta <vgupta@synopsys.com>

Signed-off-by: Vineet Gupta <vgupta@synopsys.com>

Signed-off-by: Vineet Gupta <vgupta@synopsys.com>

Signed-off-by: Vineet Gupta <vgupta@synopsys.com>

As DW Mobile Storage databook says it's required to use "Hold Register"
if card is enumerated in SDR12 or SDR25 modes.
It means we need to act in the same way as in Altera's Socfpga
implementation - set "use hold reg" bit in commad.

Note that for upstream proper solution would be to remove
dw_mci_pltfm_prepare_command() at all and set the bit right in
dw_mci_prepare_command() for all platforms.

Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>