Add device tree files for Broadcom Northstar based SVKs.  Since the
bcm5301x.dtsi already exists, all that is necessary is the dts files to
enable the UARTs.  With these files, the SVKs are able to boot to shell.

Signed-off-by: Jon Mason <jonmason@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>

Add support for the ARM TWD Timer and Watchdog to the Northstar Plus
device tree.

Signed-off-by: Jon Mason <jonmason@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>

Add NAND support to the device tree for the Broadcom Northstar Plus SoC.
Since no driver changes are needed to enable this hardware, only the
device tree changes are required to make this functional.

Signed-off-by: Jon Mason <jonmason@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>

Add PCI support to the Northstar Plus SoC.  This uses the existing
pcie-iproc driver.  So, all that is needed is device tree entries in the
DTS.

Signed-off-by: Jon Mason <jonmason@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>

This reverts commit af19161a,
which breaks the omap3 device tree build due to a wrong reference.

I accidently queued this change via the power supply subsystem while
telling Marek at the same time, that it should go through Tony.
Following that I did miss Stephen's messages about the build failure in
linux-next and since he switched to merging an older snapshot nobody
else noticed the problem in my tree. I didn't notice myself, since I
did not build any device tree files assuming none have changed by me.

Signed-off-by: Sebastian Reichel <sre@kernel.org>
Reported-by: Felipe Balbi <balbi@ti.com>
Tested-by: Felipe Balbi <balbi@ti.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Tested-by: Kevin Hilman <khilman@linaro.org>
Acked-by: Tony Lindgren <tony@atomide.com>

This patch adds DT entries for the LEDs found on the Kirkwood-based
LaCie boards 2Big and 5Big Network v2.

Signed-off-by: Simon Guinot <simon.guinot@sequanux.org>
Acked-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>

This reverts commit d871cd2e as it causes
regression in BBB

Reported-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>

This reverts commit e3faf2b8 as it causes
regression in BBB

Reported-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>

The System Bus Controller block has two register regions,
but having only the second one in a separate node was not nice.

Replace it with a new node with two register regions in it.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Olof Johansson <olof@lixom.net>

Enable building all dtb files when CONFIG_OF_ALL_DTBS is enabled. The dtbs
are not really dependent on a platform being enabled or any other kernel
config, so for testing coverage it is convenient to build all of the dtbs.
This builds all dts files in the tree, not just targets listed. This
is simpler for arm64 which has a bunch of sub-dirs.

Signed-off-by: Rob Herring <robh@kernel.org>
Cc: Russell King <linux@arm.linux.org.uk>

Switch to use the ti,edma3-tpcc and ti,edma3-tptc binding for the eDMA3 and
enable the DMA even crossbar with ti,am335x-edma-crossbar.
With the new bindings boards can customize and tweak the DMA channel
priority to match their needs. With the new binding the memcpy is safe
to be used since with the old binding it was not possible for a driver
to know which channel is allowed to be used as non HW triggered channel.

Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>

Switch to use the ti,edma3-tpcc and ti,edma3-tptc binding for the eDMA3 and
enable the DMA even crossbar with ti,am335x-edma-crossbar.
With the new bindings boards can customize and tweak the DMA channel
priority to match their needs. With the new binding the memcpy is safe
to be used since with the old binding it was not possible for a driver
to know which channel is allowed to be used as non HW triggered channel.

Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>

Add L2 cache controller nodes for all the UniPhier SoC DTSI.
Also, add an L3 cache controller node for PH1-Pro5 DTSI.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Olof Johansson <olof@lixom.net>

This allows the tuning code to run and use higher speeds on capable cards.

Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

The drive/sample clocks can be phase shifted.  The drive clock
could be used in a future patch to adjust hold times.  The sample
clock is used for tuning.

Signed-off-by: Alexandru M Stan <amstan@chromium.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Add aliases to fix the I2C indexes like the other UniPhier boards.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Olof Johansson <olof@lixom.net>

Initial version of DTS for ProXstream2 Vodka board.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>

Initial version of DTS for ProXstream2 Gentil board.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>

Specifying both console and stdout-path is redundant.  Add options
":115200n8" to stdout-path and drop "console=ttyS0,115200".

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>

The change corrects cpu compatible property to a defined one,
see Documentation/devicetree/bindings/arm/cpus.txt

Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>

The change corrects cpu compatible property to a defined one,
see Documentation/devicetree/bindings/arm/cpus.txt

Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>

Adds to the node of the DISP1 power domain the two clocks that need to
be reparented while the domain is powered off:
CLK_MOUT_ACLK200_DISP1_SUB and CLK_MOUT_ACLK300_DISP1_SUB.

Otherwise the state is unknown at power up and the mixer's clocks are
all messed up.

Signed-off-by: Tomeu Vizoso <tomeu.vizoso@collabora.com>
Link: http://lkml.kernel.org/g/561CDC33.7050103@collabora.com


Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>

The property name should be "gpio", not "gpios". Fix it.

Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>

The property name should be "gpio", not "gpios". Fix it.

Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>

Exynos USB2 PHY driver now supports VBUS regulator, so add it to all
boards which have it available. This also fixes commit
7eec1266 ("ARM: dts: Add Maxim 77693 PMIC to exynos4412-trats2"),
which added new regulators to Trats2 board, but without linking them to
the consumers.

Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Fixes: 7eec1266 ("ARM: dts: Add Maxim 77693 PMIC to exynos4412-trats2")
Signed-off-by: Kukjin Kim <kgene@kernel.org>

There are some differences of mobile storage host between exynos3250
and exnos5250. For example, exynos3250 supports the HS400 mode, but
exynos5250 doesn't support it.
Since exynos3250 can perform the similar function with exynos5420
compatible, this patch changes the compatible from exynos5250 to
exynos5420 for mshc.

Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>

We need to use it for getting video modes over HDMI.

Signed-off-by: Eric Anholt <eric@anholt.net>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>

This will give us the ability to set the pixel and HDMI state machine
clocks for the VC4 KMS driver, change the CPU frequency, and
potentially gate clocks in the future (once we also write a power
domain driver).  It also gives the uart an explicit clock reference,
so that we don't need to change the physical addresses of the old
fixed clk_bcm2835.c clocks for Raspberry Pi 2 port.

Two clocks get their frequencies updated as a result of this.  One is
uart's apb_pclk, which was previously accidentally grabbing the fixed
uart0_pclk due to the apb_pclk not having clk_register_clkdev()
called.  The uart doesn't seem to do anything with apb_pclk other than
make sure it's on, so that appears safe (also, as far as I can see,
the apb clock is actually the same as the VPU clock).  The other is
EMMC, which according to the docs was supposed to be in the 50-100Mhz
range, but it turns out the firmware needed to change to running it at
the 250Mhz core clock speed to avoid a bug in clock domain crossing.

Additionally, anything using BCM2835_CLOCK_VPU will now have a correct
clock rate if the user configures the boot-time core clock speed using
config.txt.

Signed-off-by: Eric Anholt <eric@anholt.net>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>

The MSI Primo81 is an A31s based tablet, with 1G RAM, 16G NAND,
768x1024 IPS LCD display, mono speaker, 0.3 MP front camera, 2.0 MP
rear camera, 3500 mAh battery, gt911 touchscreen, mma8452 accelerometer
and rtl8188etv usb wifi. Has "power", "volume+" and "volume-" buttons
(both volume buttons are also connected to the UBOOT_SEL pin). The
external connectors are represented by MicroSD slot, MiniHDMI, MicroUSB
OTG and 3.5mm headphone jack.

USB OTG is enabled in host only mode. AXP221 USB power supply and
GPIO support are required for full USB OTG support.

Signed-off-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
Signed-off-by: Karsten Merker <merker@debian.org>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

Some boards, such as tablets, have regulators providing power to parts
of the display pipeline, like signal converters and LCD panels.

Add labels to the simplefb device nodes so that we can reference them
in the board dts files to add regulator supply properties.

Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

Enable on-chip audio codec on the Marsboard A10.

Signed-off-by: Aleksei Mamlin <mamlinav@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

The keyboard driver for GPIO buttons(gpio-keys) checks for one of the
two boolean properties to enable gpio buttons as wakeup source:
1. "wakeup-source" or
2. the legacy "gpio-key,wakeup"

However juno, ste-snowball and emev2-kzm9d dts file have a undetected
"wakeup" property to indictate the wakeup source.

This patch fixes it by making use of "wakeup-source" property.

Cc: Magnus Damm <magnus.damm@gmail.com>
Acked-by: Simon Horman <horms@verge.net.au>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Olof Johansson <olof@lixom.net>

The Point of View protab2-ips9 is a tablet with a 9" ips 1024x768 lcd screen,
microsd slot, headphones, mini hdmi, mini usb b and power barrel connectors.

It uses a rtl8188cus usb wifi chip and a RDA 5875Y bluetooth chip attached
to uart2. It has a bma250 accelerometer attached to i2c1 addr 0x18, this
only works when ldo3 is set to 2.8 volt, otherwise i2c1 gets stuck, so
for now we mark i2c1 as failed.

It has a pixcir,pixcir_tangoc compatible touchscreen attached to i2c2 addr
0x5c. This is not enabled in this dts, because this variant of the
pixcir_tangoc has separate wakeup and enable pins both of which need
to be driven low before the touchscreen will work. Before we can enable
this the pixcir driver and devicetree-bindings need to be extended to
support these pins.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

The cubieboard uses the internal codec to output sound to its mini-jack.
Enable it.

Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

The CHIP v0.2 has a composite output on a mini-jack connector, the audio
part being provided by the on-SoC codec. Enable it.

Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>

Enable the audio-codec on the Mele A1000 top-set box.

Signed-off-by: Marcus Cooper <codekipper@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>

The cubieboard2 uses the internal codec to output sound to its mini-jack.
Enable it.

Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>

This commit enables the on-chip audio codec present on the A20 SoC
for the Cubietruck.

Signed-off-by: Emilio López <emilio@elopez.com.ar>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>

The A20 SoC includes the Allwinner audio codec, capable of both 24-bit
playback and capture. This commit adds a device node for it.

Signed-off-by: Emilio López <emilio@elopez.com.ar>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>

The A13 and A10s also have the audio codec present. List it in the device
tree.

Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>