Remove pdata quirks for the displays on boards that are now supported
properly with DT.

Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>

For booting Panda and 4430SDP with DT, while DSS did not support DT, we
had to had small hacks in the omapdss driver to get the regulators. With
DT now supported in DSS, we can remove those hacks.

Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>

OMAP DSS related .dts changes

Merge OMAP DSS DT support

Correct passing parameter sequence, which will avoid the id of
fix screen info is overwritten.

Signed-off-by: Bo Shen <voice.shen@atmel.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>

Add DT binding documentation for tpd12s015 encoder

Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Archit Taneja <archit@ti.com>

Add DT binding documentation for TFP410 encoder

Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Archit Taneja <archit@ti.com>
Acked-by: Philipp Zabel <p.zabel@pengutronix.de>

Add DT binding documentation for Sony acx565akm panel

Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Sebastian Reichel <sre@debian.org>
Reviewed-by: Archit Taneja <archit@ti.com>
Acked-by: Philipp Zabel <p.zabel@pengutronix.de>

Add DT binding documentation for MIPI DSI Command Mode Panel.

Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Archit Taneja <archit@ti.com>
Acked-by: Philipp Zabel <p.zabel@pengutronix.de>

Add DT binding documentation for HDMI Connector.

Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Archit Taneja <archit@ti.com>
Acked-by: Philipp Zabel <p.zabel@pengutronix.de>

Add DT binding documentation for DVI Connector.

Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Archit Taneja <archit@ti.com>
Acked-by: Philipp Zabel <p.zabel@pengutronix.de>

Add DT binding documentation for Analog TV Connector.

Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Archit Taneja <archit@ti.com>
Acked-by: Philipp Zabel <p.zabel@pengutronix.de>

Add DT data for OMAP3 N900 board. The board has the following displays:

lcd: LCD panel connected to OMAP's SDI output
tv: analog svideo

Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Tested-by: Sebastian Reichel <sre@debian.org>
Acked-by: Tony Lindgren <tony@atomide.com>

Add DT data for OMAP3 IGEPv2 board. The board has the following displays:

dvi: uses TFP410 encoder to convert DPI to DVI

Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>

Add DT data for OMAP3 Beagle-xM board. The board has the following displays:

dvi: uses TFP410 encoder to convert DPI to DVI
tv: analog svideo

Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>

Add DT data for OMAP3 Beagle board. The board has the following displays:

dvi: uses TFP410 encoder to convert DPI to DVI
tv: analog svideo

Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>

Add DT data for OMAP4 SDP board. The board has the following displays:

lcd0: a command mode DSI panel connected to OMAP DSI1 encoder
lcd1: a command mode DSI panel connected to OMAP DSI2 encoder
hdmi: OMAP HDMI output with TPD12S015 ESD/level shifter

Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>

Add device tree bindings for OMAP Display Subsystem for the following
SoCs: OMAP2, OMAP3, OMAP4.

Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Archit Taneja <archit@ti.com>

Add DT support for panel-sony-acx565akm

Signed-off-by: Sebastian Reichel <sre@debian.org>
[tomi.valkeinen@ti.com: some modifications]
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Archit Taneja <archit@ti.com>

Add DT support for connector-analog-tv.

Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Archit Taneja <archit@ti.com>

Add DT support for hdmi-connector.

Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Archit Taneja <archit@ti.com>

Add DT support for encoder-tpd12s015.

Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Archit Taneja <archit@ti.com>

Add DT support for connector-dvi.

Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Archit Taneja <archit@ti.com>

Add DT support for encoder-tfp410.

Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Archit Taneja <archit@ti.com>

Add DT support for panel-dsi-cm.

Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Archit Taneja <archit@ti.com>

Add the code to make the DSI driver work with device tree on OMAP3 and
OMAP4.

A minor hack is needed at the moment in the DSI driver: the DSS driver
needs to know the ID number of a DSI device, as clocks are routed in
different ways to the DSI devices. At the moment we don't have any
proper way to manage this, so this patchs adds a simple lookup table
that is used to deduce the ID from the DSI device's base address.

Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Archit Taneja <archit@ti.com>

Add DT support to VENC.

In contrast to non-DT version, the DT version gets the invert-polarity
and connector type via venc's endpoint, not from the connector.

Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Archit Taneja <archit@ti.com>

Add DT support to HDMI driver. The only thing needed for DT support here
is the of_match_table.

Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Archit Taneja <archit@ti.com>

Add DT support to DISPC. Only thing needed here is the of_match_table.

Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Archit Taneja <archit@ti.com>

Add DT support for DSS. Contrary to the non-DT version, the DSS in DT
mode contains DPI and SDI outputs, which better reflects the hardware.
The non-DT code will be removed after all boards have been converted to
DT, so there's no need to change the non-DT code to act the same way.

The code for DPI and SDI needs to be refined later to make it possible
to add multiple DPI ports. For now, handling just a single DPI port is
enough for all the boards.

Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Archit Taneja <archit@ti.com>

The regulator names used for DSS components are somewhat ugly for DT
use. As we're just adding DT support, it's simple to change the
regulator names.

This patch makes the DSS driver get the regulators with somewhat cleaner
names when bootin with DT. For example, this allows us to define HDMI's
VDDA regulator in the DT data as:

vdda-supply = <...>;

instead of

vdda_hdmi_dac-supply = <...>;

Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Archit Taneja <archit@ti.com>

Add helpers to get ports and endpoints from DT data.

These helpers parse v4l2 style ports and endpoints, but compared to the
v4l2 helpers, these allow iterating ports and endpoints separately.

This is a temporary solution until we get generic code to parse the
ports and endpoints.

Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Archit Taneja <archit@ti.com>

Improve the search for the default display in two ways:
* compare the given display name to the display's alias
* if no display name is given, look for "display0" DT alias

Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Archit Taneja <archit@ti.com>

Separate the code for finding the default display into a function for
clarity and to make it easier to extend it in the future.

Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Archit Taneja <archit@ti.com>

We currently create a "displayX" style alias name for all displays,
using a number that is incremented for each registered display. With the
new DSS device model there is no clear order in which the displays are
registered, and thus the numbering is somewhat random.

This patch improves the behavior for DT case so that if the displays
have been assigned DT aliases, those aliases will be used as DSS
aliases.

This means that "display0" is always the one specified in the DT alias,
and thus display0 can be used as default display in case the user didn't
specify a default display.

Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Archit Taneja <archit@ti.com>

Add support to get the label (i.e. a "nickname") for a display from the
DT data. If there is no label defined, use the display's alias (e.g.
'display0') as a name.

Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Archit Taneja <archit@ti.com>

As there is no common panel framework in the kernel, we have OMAP
specific panel drivers. However, the DT data should be generic. This
brings the issue that some other platform could use the same panels, and
would need to create a driver with the same 'compatible' string as the
OMAP driver.

In the long run, we have to get a common panel framework. For the time
being, this patch solves the issue:

At early boot time, we go through the DT nodes looking for the panels
the kernel supports for OMAP. For each found node, the 'compatible'
string is prepended with "omapdss,", i.e. "sony,acx565akm" becomes
"omapdss,sony,acx565akm". The OMAP display drivers all have "omapdss,"
at the beginning of their compatible field.

This allows us to have generic DT data, but OMAP specific display
drivers.

Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Archit Taneja <archit@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>

The OMAP display architecture requires a bunch of platform devices which
are not created via .dts (for now). We also need to pass a few function
pointers and the DSS hardware version from the arch code to omapdss
driver.

This patch adds omapdss_init_of() function, called from board-generic at
init time, which handles those tasks.

Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Archit Taneja <archit@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>

Add DT data for OMAP4 Pandaboard. The board has the following displays:

dvi: uses TFP410 encoder to convert DPI to DVI
hdmi: OMAP HDMI output with TPD12S015 ESD/level shifter

Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>

Add DT data for OMAP4 display subsystem, which contains the following
blocks:

dss - the wrapper/glue for the display modules
dispc - display controller
dsi - MIPI DSI encoder (two independent modules)
rfbi - MIPI DBI encoder
venc - analog TV encoder
hdmi - HDMI encoder

Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>