* clk-davinci:
  clk: davinci: add a reset lookup table for psc0
  reset: modify the way reset lookup works for board files
  reset: add support for non-DT systems

In order to be able to use the reset framework in legacy boot mode as
well, add the reset lookup table to the psc driver for da850 variant.

Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Reviewed-by: David Lechner <david@lechnology.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>

We need this to be able to use the reset_controller_add_lookup() API.

* 'reset/lookup' of git://git.pengutronix.de/git/pza/linux:
  reset: modify the way reset lookup works for board files
  reset: add support for non-DT systems

* clk-stratix10:
  clk: socfpga: stratix10: add clock driver for Stratix10 platform
  dt-bindings: documentation: add clock bindings information for Stratix10

* clk-imx:
  clk: imx7d: Move clks_init_on before any clock operations
  clk: imx7d: Correct ahb clk parent select
  clk: imx7d: Correct dram pll type
  clk: imx7d: Add USB clock information
  clk: imx: pllv2: avoid using uninitialized values
  clk: imx6ull: Add epdc_podf instead of sim_podf
  clk: imx: imx7d: correct video pll clock tree
  clk: imx: imx7d: add the Keypad Port module clock
  clk: imx7d: add CAAM clock
  clk: imx: imx7d: add the snvs clock
  clk: imx: imx6sx: update cko mux options

* clk-bcm:
  clk: bcm2835: De-assert/assert PLL reset signal when appropriate

* clk-cs2000:
  clk: cs2000: set pm_ops in hibernate-compatible way

* clk-imx6sll:
  clk: imx: add clock driver for imx6sll
  dt-bindings: imx: update clock doc for imx6sll
  clk: imx: add new gate/gate2 wrapper funtion
  clk: imx: Add CLK_IS_CRITICAL flag for busy divider and busy mux

Merge branches 'clk-davinci', 'clk-si544', 'clk-rockchip', 'clk-uniphier' and 'clk-ti-flag-fix' into clk-next

* clk-davinci:
  clk: davinci: Remove redundant dev_err calls
  clk: davinci: cfgchip: Add TI DA8XX USB PHY clocks
  clk: davinci: New driver for TI DA8XX CFGCHIP clocks
  dt-bindings: clock: Add bindings for DA8XX CFGCHIP clocks
  clk: davinci: Add platform information for TI DM646x PSC
  clk: davinci: Add platform information for TI DM644x PSC
  clk: davinci: Add platform information for TI DM365 PSC
  clk: davinci: Add platform information for TI DM355 PSC
  clk: davinci: Add platform information for TI DA850 PSC
  clk: davinci: Add platform information for TI DA830 PSC
  clk: davinci: New driver for davinci PSC clocks
  dt-bindings: clock: New bindings for TI Davinci PSC
  clk: davinci: Add platform information for TI DM646x PLL
  clk: davinci: Add platform information for TI DM644x PLL
  clk: davinci: Add platform information for TI DM365 PLL
  clk: davinci: Add platform information for TI DM355 PLL
  clk: davinci: Add platform information for TI DA850 PLL
  clk: davinci: Add platform information for TI DA830 PLL
  clk: davinci: New driver for davinci PLL clocks
  dt-bindings: clock: Add new bindings for TI Davinci PLL clocks

* clk-si544:
  clk: Add driver for the si544 clock generator chip

* clk-rockchip:
  clk: rockchip: assign correct id for pclk_ddr and hclk_sd in rk3399
  clk: rockchip: Fix error return in phase clock registration
  clk: rockchip: Correct the behaviour of restoring cached phase
  clk: rockchip: Fix wrong parents for MMC phase clock for rk3328
  clk: rockchip: Fix wrong parent for SDMMC phase clock for rk3228
  clk: rockchip: Add 1.6GHz PLL rate for rk3399
  clk: rockchip: Restore the clock phase after the rate was changed
  clk: rockchip: Prevent calculating mmc phase if clock rate is zero
  clk: rockchip: Free the memory on the error path
  clk: rockchip: document hdmi_phy external input for rk3328
  clk: rockchip: add flags for rk3328 dclk_lcdc
  clk: rockchip: remove ignore_unused flag from rk3328 vio_h2p clocks
  clk: rockchip: protect all remaining rk3328 interconnect clocks
  clk: rockchip: export sclk_hdmi_sfc on rk3328
  clk: rockchip: remove HCLK_VIO from rk3328 dt header
  clk: rockchip: fix hclk_vio_niu on rk3328

* clk-uniphier:
  clk: uniphier: add additional ethernet clock lines for Pro4
  clk: uniphier: add SATA clock control support
  clk: uniphier: add PCIe clock control support
  clk: uniphier: add ethernet clock control support for PXs3
  clk: uniphier: add Pro4/Pro5/PXs2 audio system clock

* clk-ti-flag-fix:
  clk: ti: fix flag space conflict with clkctrl clocks
  clk: ti: clkctrl: add support for CLK_SET_RATE_PARENT flag

Merge branches 'clk-mediatek', 'clk-hisi', 'clk-allwinner', 'clk-ux500' and 'clk-renesas' into clk-next

* clk-mediatek:
  clk: mediatek: add audsys support for MT2701
  clk: mediatek: add devm_of_platform_populate() for MT7622 audsys
  dt-bindings: clock: mediatek: add audsys support for MT2701
  dt-bindings: clock: mediatek: update audsys documentation to adapt MFD device
  clk: mediatek: update missing clock data for MT7622 audsys
  clk: mediatek: fix PWM clock source by adding a fixed-factor clock
  dt-bindings: clock: mediatek: add binding for fixed-factor clock axisel_d4

* clk-hisi:
  clk: hisilicon: fix potential NULL dereference in hisi_clk_alloc()
  clk: hisilicon: mark wdt_mux_p[] as const
  clk: hisilicon: Mark phase_ops static
  clk: hi3798cv200: add emmc sample and drive clock
  clk: hisilicon: add hisi phase clock support
  clk: hi3798cv200: add COMBPHY0 clock support
  clk: hi3798cv200: fix define indentation
  clk: hi3798cv200: add support for HISTB_USB2_OTG_UTMI_CLK
  clk: hi3798cv200: correct IR clock parent
  clk: hi3798cv200: fix unregister call sequence in error path

* clk-allwinner:
  clk: sunxi-ng: add missing hdmi-slow clock for H6 CCU
  clk: sunxi-ng: add support for the Allwinner H6 CCU
  dt-bindings: add device tree binding for Allwinner H6 main CCU
  clk: sunxi-ng: Support fixed post-dividers on NKMP style clocks
  clk: sunxi-ng: h3: h5: export CLK_PLL_VIDEO
  clk: sunxi-ng: h3: h5: Allow some clocks to set parent rate
  clk: sunxi-ng: h3: h5: Add minimal rate for video PLL
  clk: sunxi-ng: Add check for minimal rate to NM PLLs
  clk: sunxi-ng: Use u64 for calculation of nkmp rate
  clk: sunxi-ng: Mask nkmp factors when setting register
  clk: sunxi-ng: remove select on obsolete SUNXI_CCU_X kconfig name

* clk-ux500:
  clk: ux500: Drop AB8540/9540 support

* clk-renesas: (27 commits)
  clk: renesas: cpg-mssr: Adjust r8a77980 ifdef
  clk: renesas: rcar-gen3: Always use readl()/writel()
  clk: renesas: sh73a0: Always use readl()/writel()
  clk: renesas: rza1: Always use readl()/writel()
  clk: renesas: rcar-gen2: Always use readl()/writel()
  clk: renesas: r8a7740: Always use readl()/writel()
  clk: renesas: r8a73a4: Always use readl()/writel()
  clk: renesas: mstp: Always use readl()/writel()
  clk: renesas: div6: Always use readl()/writel()
  clk: fix false-positive Wmaybe-uninitialized warning
  clk: renesas: r8a77965: Replace DU2 clock
  clk: renesas: cpg-mssr: Add support for R-Car M3-N
  clk: renesas: cpg-mssr: add R8A77980 support
  dt-bindings: clock: add R8A77980 CPG core clock definitions
  clk: renesas: r8a7792: Add rwdt clock
  clk: renesas: r8a7794: Add rwdt clock
  clk: renesas: r8a7791/r8a7793: Add rwdt clock
  clk: renesas: r8a7790: Add rwdt clock
  clk: renesas: r8a7745: Add rwdt clock
  clk: renesas: r8a7743: Add rwdt clock
  ...

Merge branches 'clk-mvebu', 'clk-phase', 'clk-nxp', 'clk-mtk2712' and 'clk-qcom-rpmcc' into clk-next

* clk-mvebu:
  clk: mvebu: armada-38x: add support for missing clocks
  clk: mvebu: cp110: Fix clock tree representation

* clk-phase:
  clk: Don't show the incorrect clock phase
  clk: update cached phase to respect the fact when setting phase

* clk-nxp:
  clk: lpc32xx: Set name of regmap_config

* clk-mtk2712:
  clk: mediatek: update clock driver of MT2712
  dt-bindings: clock: add clocks for MT2712

* clk-qcom-rpmcc:
  clk: qcom: rpmcc: Add support to XO buffered clocks

Merge branches 'clk-spreadtrum', 'clk-stm32f', 'clk-stm32mp1', 'clk-hi655x' and 'clk-gpio' into clk-next

* clk-spreadtrum:
  clk: sprd: add RTC gate for SC9860
  dt-bindings: clocks: add APB RTC gate for SC9860

* clk-stm32f:
  clk: stm32: Add clk entry for SDMMC2 on stm32F769
  clk: stm32: Add DSI clock for STM32F469 Board
  clk: stm32: END_PRIMARY_CLK should be declare after CLK_SYSCLK

* clk-stm32mp1:
  clk: stm32: add configuration flags for each of the stm32 drivers
  clk: stm32mp1: add Debug clocks
  clk: stm32mp1: add MCO clocks
  clk: stm32mp1: add RTC clock
  clk: stm32mp1: add Peripheral & Kernel Clocks
  clk: stm32mp1: add Kernel timers
  clk: stm32mp1: add Sub System clocks
  clk: stm32mp1: add Post-dividers for PLL
  clk: stm32mp1: add PLL clocks
  clk: stm32mp1: add Source Clocks for PLLs
  clk: stm32mp1: add MP1 gate for hse/hsi/csi oscillators
  clk: stm32mp1: Introduce STM32MP1 clock driver
  dt-bindings: Document STM32MP1 Reset Clock Controller (RCC) bindings

* clk-hi655x:
  clk: enable hi655x common clk automatically

* clk-gpio:
  clk: clk-gpio: Allow GPIO to sleep in set/get_parent

Merge branches 'clk-versatile', 'clk-doc', 'clk-must-check', 'clk-qcom' and 'clk-debugfs' into clk-next

* clk-versatile:
  clk: versatile: Remove WARNs in ->round_rate()
  clk: versatile: add min/max rate boundaries for vexpress osc clock

* clk-doc:
  Documentation: clk: enable lock is not held for clk_is_enabled API

* clk-must-check:
  clk: add more __must_check for bulk APIs

* clk-qcom:
  clk: qcom: smd-rpm: Migrate to devm_of_clk_add_hw_provider()
  clk: qcom: gcc-msm8996: Mark aggre0 noc clks as critical

* clk-debugfs:
  clk: Re-use DEFINE_SHOW_ATTRIBUTE() macro

* clk-ti:
  clk: keystone: sci-clk: add support for dynamically probing clocks
  clk: ti: add support for clock latching to mux clocks
  clk: ti: add support for clock latching to divider clocks
  clk: ti: add generic support for clock latching
  clk: ti: add support for register read-modify-write low-level operation
  dt-bindings: clock: ti: add latching support to mux and divider clocks

* clk-amlogic: (50 commits)
  clk: meson: Drop unused local variable and add static
  clk: meson: clean-up clk81 clocks
  clk: meson: add fdiv clock gates
  clk: meson: add mpll pre-divider
  clk: meson: axg: add hifi pll clock
  clk: meson: axg: add hifi clock bindings
  clk: meson: add ROUND_CLOSEST to the pll driver
  clk: meson: add gp0 frac parameter for axg and gxl
  clk: meson: improve pll driver results with frac
  clk: meson: remove special gp0 lock loop
  clk: meson: poke pll CNTL last
  clk: meson: add fractional part of meson8b fixed_pll
  clk: meson: use hhi syscon if available
  clk: meson: remove obsolete cpu_clk
  clk: meson: rework meson8b cpu clock
  clk: meson: split divider and gate part of mpll
  clk: meson: migrate plls clocks to clk_regmap
  clk: meson: migrate the audio divider clock to clk_regmap
  clk: meson: migrate mplls clocks to clk_regmap
  clk: meson: add regmap helpers for parm
  ...

* clk-tegra:
  clk: tegra: Fix pll_u rate configuration
  clk: tegra: Specify VDE clock rate
  clk: tegra20: Correct PLL_C_OUT1 setup
  clk: tegra: Mark HCLK, SCLK and EMC as critical
  clk: tegra: MBIST work around for Tegra210
  clk: tegra: add fence_delay for clock registers
  clk: tegra: Add la clock for Tegra210

* clk-samsung: (22 commits)
  clk: samsung: Mark a few things static
  clk: samsung: Add fout=196608001 Hz EPLL rate entry for exynos4412
  clk: samsung: exynos5250: Add missing clocks for FIMC LITE SYSMMU devices
  clk: samsung: exynos5420: Add more entries to EPLL rate table
  clk: samsung: exynos5420: Add CLK_SET_RATE_PARENT flag to mout_mau_epll_clk
  clk: samsung: exynos5250: Move PD-dependent clocks to Exynos5 sub-CMU
  clk: samsung: exynos5420: Move PD-dependent clocks to Exynos5 sub-CMU
  clk: samsung: Add Exynos5 sub-CMU clock driver
  soc: samsung: pm_domains: Add blacklisting clock handling
  clk: samsung: Add compile time PLL rate validators
  clk: samsung: s3c2410: Fix PLL rates
  clk: samsung: exynos7: Fix PLL rates
  clk: samsung: exynos5433: Fix PLL rates
  clk: samsung: exynos5260: Fix PLL rates
  clk: samsung: exynos5250: Fix PLL rates
  clk: samsung: exynos3250: Fix PLL rates
  clk: exynos5433: Extend list of available AUD_PLL output frequencies
  clk: exynos5433: Add CLK_IGNORE_UNUSED flag to sclk_ioclk_i2s1_bclk
  clk: samsung: Add a git tree entry to MAINTAINERS
  clk: samsung: Remove redundant dev_err call in exynos_audss_clk_probe()
  ...

Add clk driver support for imx6sll.

Signed-off-by: Bai Ping <ping.bai@nxp.com>
Acked-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>

Add clock binding doc update for imx6sll.

Signed-off-by: Bai Ping <ping.bai@nxp.com>
Acked-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>

Add new gate/gate2 wrapper function to register clocks with optional flags.

Signed-off-by: Bai Ping <ping.bai@nxp.com>
Acked-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>

The busy divider and busy mux is actually used by the system critical clocks,
so add 'CLK_IS_CRITICAL' to clocks registered with these two type.

Signed-off-by: Bai Ping <ping.bai@nxp.com>
Acked-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>

Use SET_LATE_SYSTEM_SLEEP_PM_OPS() macro instead of direct assignment to
.resume_early field.

This fixes initialization of CS2000 in restore from hibernation in case
of kernel used to load image did not initialize CS2000 while kernel
being restored had CS2000 initialized.

Signed-off-by: Nikita Yushchenko <nikita.yoush@cogentembedded.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>

In order to enable a PLL, not only the PLL has to be powered up and
locked, but you also have to de-assert the reset signal. The last part
was missing. Add it so PLLs that were not enabled by the FW/bootloader
can be enabled from Linux.

Fixes: 41691b88

 ("clk: bcm2835: Add support for programming the audio domain clocks")
Cc: <stable@vger.kernel.org>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>

For init on clocks we should move it at the first place in imx7d_clocks_init()
before any clock operations, else the clock operation may fail in case the clock
is still not on.

Acked-by: Ranjani Vaidyanathan <Ranjani.Vaidyanathan@freescale.com>
Signed-off-by: Dong Aisheng <b29396@freescale.com>
Signed-off-by: Irina Tirdea <irina.tirdea@nxp.com>
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>

Design team change the ahb's clk parent options but
did NOT update the DOC accordingly in time, so the
AHB/IPG's clk rate in clk tree is incorrect, AHB is
67.5MHz and IPG is 33.75MHz, but using scope to
monitor them, they are actually 135MHz and 67.5MHz,
update the clk parent option to make clk tree info
correct.

Signed-off-by: Anson Huang <b20788@freescale.com>
Signed-off-by: Irina Tirdea <irina.tirdea@nxp.com>
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>

DRAM PLL is a audio/video type PLL, need to correct
it to get correct ops of PLL.

There is a test_div placed before DRAM PLL's gate, so
add this test div clk.

Signed-off-by: Anson Huang <b20788@freescale.com>
Signed-off-by: Irina Tirdea <irina.tirdea@nxp.com>
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>

Add USB clock information, the pll_usb_main_clk is USB_PLL at CCM
which is the output of USBOTG2 PHY.

Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Irina Tirdea <irina.tirdea@nxp.com>
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>

Add a clock driver for the Stratix10 SoC. The driver is similar to the
Cyclone5/Arria10 platforms, with the exception that this driver only uses
one single clock binding.

Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>

Document that Stratix10 clock bindings, and add the clock header file. The
clock header is an enumeration of all the different clocks on the Stratix10
platform.

Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>

The introduction of support for CLK_SET_RATE_PARENT flag for clkctrl
clocks used a generic clock flag, which causes a conflict with the
rest of the clkctrl flags, namely the NO_IDLEST flag. This can cause
boot failures on certain platforms where this flag is introduced, by
omitting the wait for the clockctrl module to be fully enabled before
proceeding with rest of the code.

Fix this by moving all the clkctrl specific flags to their own bit-range.

Signed-off-by: Tero Kristo <t-kristo@ti.com>
Fixes: 49159a9d

 ("clk: ti: add support for CLK_SET_RATE_PARENT flag")
Reported-by: Christophe Lyon <christophe.lyon@linaro.org>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>

Pro4 SoC has clock lines for Giga-bit feature and ethernet phy,
and these are mandatory to activate the ethernet controller. This adds
support for the clock lines.

Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Acked-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>

Add clock control for SATA controller on UniPhier SoCs. This adds
support for PXs2, LD20 and PXs3.

Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Acked-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>

Add clock control for PCIe controller on UniPhier SoCs. This adds
support for Pro5, LD20 and PXs3.

Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Acked-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>

Merge tag 'v4.17-rockchip-clk-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into clk-rockchip

Pull more Rockchip clk driver updates from Heiko Stuebner:

Some more fixes for Rockchip clocks mainly resulting from the changes in
phase-handling. Which revealed some parent issues on rk3228 and rk3328 as
well as additional issue in how handle phase restoration.
And to top it off two assignments of already existing clock ids for rk3399.

* tag 'v4.17-rockchip-clk-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
  clk: rockchip: assign correct id for pclk_ddr and hclk_sd in rk3399
  clk: rockchip: Fix error return in phase clock registration
  clk: rockchip: Correct the behaviour of restoring cached phase
  clk: rockchip: Fix wrong parents for MMC phase clock for rk3328
  clk: rockchip: Fix wrong parent for SDMMC phase clock for rk3228

Commit 7af1bb19f1d7 ("reset: add support for non-DT systems")
introduced reset control lookup mechanism for boards that still use
board files.

The routine used to register lookup entries takes the corresponding
reset_controlled_dev structure as argument.

It's been determined however that for the first user of this new
interface - davinci psc driver - it will be easier to register the
lookup entries using the reset controller device name.

This patch changes the way lookup entries are added.

Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
[p.zabel@pengutronix.de: added missing ERR_PTR]
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>

The reset framework only supports device-tree. There are some platforms
however, which need to use it even in legacy, board-file based mode.

An example of such architecture is the DaVinci family of SoCs which
supports both device tree and legacy boot modes and we don't want to
introduce any regressions.

We're currently working on converting the platform from its hand-crafted
clock API to using the common clock framework. Part of the overhaul will
be representing the chip's power sleep controller's reset lines using
the reset framework.

This changeset extends the core reset code with a new reset lookup
entry structure. It contains data allowing the reset core to associate
reset lines with devices by comparing the dev_id and con_id strings.

It also provides a function allowing drivers to register lookup entries
with the framework.

The new lookup function is only called as a fallback in case the
of_node field is NULL and doesn't change anything for current users.

Tested with a dummy reset driver with several lookup entries.

An example lookup table registration from a driver can be found below:

static struct reset_control_lookup foobar_reset_lookup[] = {
	RESET_LOOKUP("foo.0", "foo", 15),
	RESET_LOOKUP("bar.0", NULL,   5),
};

foobar_probe()
{
...

        reset_controller_add_lookup(&rcdev, foobar_reset_lookup,
                                    ARRAY_SIZE(foobar_reset_lookup));

...
}

Cc: Sekhar Nori <nsekhar@ti.com>
Cc: Kevin Hilman <khilman@baylibre.com>
Cc: David Lechner <david@lechnology.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>

This patch adds the driver and devicetree documentation for the
Silicon Labs SI544 clock generator chip. This is an I2C controlled
oscillator capable of generating clock signals ranging from 200kHz
to 1500MHz.

Signed-off-by: Mike Looijmans <mike.looijmans@topic.nl>
[sboyd: assign max_freq to 0 in is_valid_frequency() to squelch warning]
Signed-off-by: Stephen Boyd <sboyd@kernel.org>

There is a error message within devm_ioremap_resource
already, so remove the dev_err call to avoid redundant
error message.

Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Reviewed-by: David Lechner <david@lechnology.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>

Merge tag 'clk-renesas-for-v4.17-tag2' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-drivers into clk-renesas

Pull Renesas clk driver updates from Geert Uytterhoeven:

  - Fix the incorrect display clock on R-Car M3-N,
  - Always use readl()/writel(),
  - Small fixes.

* tag 'clk-renesas-for-v4.17-tag2' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-drivers:
  clk: renesas: cpg-mssr: Adjust r8a77980 ifdef
  clk: renesas: rcar-gen3: Always use readl()/writel()
  clk: renesas: sh73a0: Always use readl()/writel()
  clk: renesas: rza1: Always use readl()/writel()
  clk: renesas: rcar-gen2: Always use readl()/writel()
  clk: renesas: r8a7740: Always use readl()/writel()
  clk: renesas: r8a73a4: Always use readl()/writel()
  clk: renesas: mstp: Always use readl()/writel()
  clk: renesas: div6: Always use readl()/writel()
  clk: renesas: r8a77965: Replace DU2 clock

Add clock control for ethernet controller on PXs3 SoC.

Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Acked-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>

The AB8540 was an evolved version of the AB8500, but it was never
mass produced or put into products, only reference designs exist.
The upstream support was never completed and it is unlikely that
this will happen so drop the support for now to simplify
maintenance of the AB8500.

Cc: Loic Pallardy <loic.pallardy@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>

Merge tag 'sunxi-clk-for-4.17' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux into clk-allwinner

Pull Allwinner clock changes from Maxime Ripard:

Our usual bunch of changes for the next merge window. The most significant
addition is the support of the H6 clock unit. Other than that, there's a
bunch of fixes for the video clocks on the H3 and H5, and some Kconfig
cleanup.

* tag 'sunxi-clk-for-4.17' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux:
  clk: sunxi-ng: add missing hdmi-slow clock for H6 CCU
  clk: sunxi-ng: add support for the Allwinner H6 CCU
  dt-bindings: add device tree binding for Allwinner H6 main CCU
  clk: sunxi-ng: Support fixed post-dividers on NKMP style clocks
  clk: sunxi-ng: h3: h5: export CLK_PLL_VIDEO
  clk: sunxi-ng: h3: h5: Allow some clocks to set parent rate
  clk: sunxi-ng: h3: h5: Add minimal rate for video PLL
  clk: sunxi-ng: Add check for minimal rate to NM PLLs
  clk: sunxi-ng: Use u64 for calculation of nkmp rate
  clk: sunxi-ng: Mask nkmp factors when setting register
  clk: sunxi-ng: remove select on obsolete SUNXI_CCU_X kconfig name

Since hclk_sd and pclk_ddr source clock from CPLL or GPLL,
and these two PLL may change their frequency. If we do not
assign right id to pclk_ddr and hclk_sd, they will alway use
default cur register value, and may get the frequency
exceed their signed off frequency. So assign correct Id
for them, then we can assign frequency for them in dts.

Signed-off-by: Lin Huang <hl@rock-chips.com>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>

The newly added clock notifier may return an error code but so far the
error output in the function would only return an error pointer from
registering the clock.

So when the clock notifier fails the clock would be unregistered but the
return would still be the clock pointer which could then not be
dereferenced correctly. So fix the error handling to prevent that.

Fixes: 60cf09e4

 ("clk: rockchip: Restore the clock phase after the rate was changed")
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>

We can't restore every phase, for instance the invalid phase and
the phase for coming rate which is out of the scope of boards'
ability. And this patch also corrects the error path to return
invalid pointer to clk if clk_notifier_register failed introduced
by the same offending commit.

Fixes: 60cf09e4

 ("clk: rockchip: Restore the clock phase after the rate was changed")
Reported-by: wlq <wlq@rock-chips.com>
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Tested-by: wlq <wlq@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>

commit c420c1e4db22 ("clk: rockchip: Prevent calculating mmc phase if
clock rate is zero") catches some gremlins for clk-rk3328.c that the
parents of MMC phase clock should be clk_{sdmmc, sdio, emmc}, but not
sclk_{sdmmc, sdio, emmc}.

Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>

commit c420c1e4db22 ("clk: rockchip: Prevent calculating mmc phase
if clock rate is zero") catches one gremlin again for clk-rk3228.c
that the parent of SDMMC phase clock should be sclk_sdmmc0, but not
sclk_sdmmc. However, the naming of the sdmmc clocks varies in the
manual with the card clock having the 0 while the hclk is named
without appended 0. So standardize one one format to prevent
confusion, as there also is only one (non-sdio) mmc controller on
the soc.

Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>