This commit adds the device tree description for the Synology DS116 NAS.

It is a one-bay NAS powered by a Marvell Armada 385 at 1.866 GHz. The
device features the following items :
  - 1 GB DDR3 RAM
  - a 8MB SPI flash
  - 2 USB3 ports, power-controlled via a GPIO for each
  - 1 gigabit ethernet interface connected over SGMII to a 88e1514 phy
  - a single SATA port, power-controlled via a GPIO
  - a battery-powered RTC
  - one UART connected to the serial console (2mm connector on board)
  - the Tx line of the second UART connected to a PIC microcontroller
    dealing with beep, reset, power-off and LED blinking (9600 Bps)
  - some of the front-panel LEDs are connected to GPIOs, one is directly
    connected to the SATA link to report disk activity.
  - a GPIO-controlled fan (3 bits for 7 speeds and OFF)

With this DTS, my NAS is 100% functional starting with kernel 4.9.

Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Willy Tarreau <w@1wt.eu>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>

The rename of orion5x-lschl.dts needs to be reflected in the Makefile:

make[3]: *** No rule to make target 'arch/arm/boot/dts/orion5x-lschl.dtb', needed by '__build'.

Fixes: 6cfd3cd8

 ("ARM: dts: orion5x-lschl: More consistent naming on linkstation series")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>

These boards are Marvell's evaluation boards for the 98DX4251 and
98DX3336 SoCs.

[gregory.clement@free-electrons.com: fix topic and update Makefile]
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>

The Beelink X2 is an STB based on the Allwinner H3 SoC with a uSD slot,
2 USB ports( 1 * USB-2 Host, 1 USB OTG), a 10/100M ethernet port using the
SoC's integrated PHY, Wifi via an sdio wifi chip, HDMI, an IR receiver, a
dual colour LED and an optical S/PDIF connector.

Signed-off-by: Marcus Cooper <codekipper@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

Lichee Pi Zero is a small-sized V3s board, which is
breadboard-compatible, and with a MicroUSB port with both OTG function
and power function.

Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

The phyCORE-AM335x development kit is a combination of the
phyCORE-AM335x SoM and a PCM-953 carrier board. The features
of the PCM-953 are:
* ETH phy on carrier board: 1x RGMII
* 1x CAN
* Up to 4x UART
* USB0 (otg)
* USB1 (host)
* SD slot
* User gpio-keys
* User LEDs

Signed-off-by: Teresa Remmet <t.remmet@phytec.de>
Reviewed-by: Wadim Egorov <w.egorov@phytec.de>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Engicam Is.IoT MX6UL has separate module for NAND, so add nand dts
file for imx6ul-isiot.dtsi.

dmesg:
-----
nand: device found, Manufacturer ID: 0x2c, Chip ID: 0xda
nand: Micron MT29F2G08ABAEAH4
nand: 256 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64
gpmi-nand 1806000.gpmi-nand: enable the asynchronous EDO mode 5
gpmi-nand 1806000.gpmi-nand: driver registered.

Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Engicam Is.IoT MX6UL has separate module for eMMC, so add emmc dts
file for imx6ul-isiot.dtsi, usdhc2 node represent eMMC.

dmesg:
-----
mmc1: SDHCI controller on 2194000.usdhc [2194000.usdhc] using ADMA
mmc1: new DDR MMC card at address 0001
mmcblk1: mmc1:0001 M62704 3.53 GiB

Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

OPOS6UL is an i.MX6UL based SoM.
OPOS6ULDev is a carrier board for the OPOS6UL SoM.

For more details see:
http://www.opossom.com/english/products-processor_boards-opos6ul.html
http://www.opossom.com/english/products-development_boards-opos6ul_dev.html



Signed-off-by: Sébastien Szymanski <sebastien.szymanski@armadeus.com>

This adds a device tree definition file for LEGO MINDSTORMS EV3.

What is working:

* Pin muxing
* Pinconf
* GPIOs
* MicroSD card reader
* UART on input port 1
* Buttons
* LEDs
* Poweroff/reset
* Flash memory
* EEPROM
* USB host port
* USB peripheral port

What is not working/to be added later:

* Speaker - have patch submitted to get pwm-beeper working - maybe someday
  it will have a real sound driver that uses PRU
* A/DC chip - have driver submitted and accepted - waiting for ack on
  device tree bindings
* Display - waiting for "simple DRM" to be mainlined
* Bluetooth - needs new driver for sequencing power/enable/clock
* Input and output ports - need some sort of new phy or extcon driver as
  well as PRU UART and PRU I2C drivers
* Battery indication - needs new power supply driver

Note on flash partitions:

These partitions are based on the official EV3 firmware from LEGO. It is
expected that most users of the mainline kernel on EV3 will be booting from
an SD card while retaining the official firmware in the flash memory.
Furthermore, the official firmware uses an ancient U-Boot (2009) that has
no device tree support. So, it makes sense to have this partition table in
the EV3 device tree file. In the unlikely case that anyone does create
their own firmware image with different partitioning, they can use a modern
U-Boot in their own firmware image that modifies the device tree with the
custom partitions.

Signed-off-by: David Lechner <david@lechnology.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>

Luxul XWR-1200 in a dual-band router based on BCM47081. It uses serial
flash (for bootloader and NVRAM) and NAND flash (for firmware).

Signed-off-by: Dan Haab <dhaab@luxul.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>

Luxul XAP-1410 in a dual-band access point device based on BCM47081 with
serial flash. It has 3 LEDs and just one (reset) button.

Signed-off-by: Dan Haab <dhaab@luxul.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>

Lichee Pi One is a low-cost Allwinner A13-based development board, with
an AXP209 PMU, a USB2.0 OTG port, a USB2.0 host port (or an onboard
RTL8723BU Wi-Fi card), optional headers for LCD and CSI, two GPIO
headers and two MicroSD card slots (connected to mmc0 and mmc2, both
bootable).

Add support for it.

Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

Orange Pi Zero is a board that came with the new Allwinner H2+ SoC and a
SDIO Wi-Fi chip by Allwinner (XR819).

Add a device tree file for it.

Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

The commit 10efbf5f

 ("ARM: dts: sun8i: Add dts file for NanoPi M1 SBC")
introduced NanoPi M1 board but it's missing in Allwinner H3 DTB build.

Signed-off-by: Milo Kim <woogyom.kim@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

The Axentia TSE-850 is a SAMA5D3-based device designed to generate
FM subcarrier signals.

Signed-off-by: Peter Rosin <peda@axentia.se>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>

The sama5d36ek CMP board is the variant of sama5d3xek board.
It is equipped with the low-power DDR2 SDRAM, PMIC ACT8865 and
some power rail. Its main purpose is used to measure the power
consumption.
The difference of the sama5d36ek CMP dts from sama5d36ek dts is
listed as below.
 1. The USB host nodes are removed, that is, the USB host is disabled.
 2. The gpio_keys node is added to wake up from the sleep.
 3. The LCD isn't supported due to the pins for LCD are conflicted
    with gpio_keys.
 4. The adc0 node support the pinctrl sleep state to fix the over
    consumption on VDDANA.

As said in errata, "When the USB host ports are used in high speed
mode (EHCI), it is not possible to suspend the ports if no device is
attached on each port. This leads to increased power consumption even
if the system is in a low power mode." That is why the the USB host
is disabled.

Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>

Romulus is an OpenPower machine with an ast2500 BMC. It has NCSI
networking and 512MB of RAM.

Signed-off-by: Joel Stanley <joel@jms.id.au>

Add .dts file for rev. C of the board by factoring out commonalities
into a shared include file (vf610-zii-dev-rev-b-c.dtsi) and deriving
revision specific file from it (vf610-zii-dev-rev-b.dts and
vf610-zii-dev-reb-c.dts).

Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Sascha Hauer <kernel@pengutronix.de>
Cc: Stefan Agner <stefan@agner.ch>
Cc: devicetree@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Cc: andrew@lunn.ch
Cc: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Cc: Nikita Yushchenko <nikita.yoush@cogentembedded.com>
Cc: cphealy@gmail.com
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Use common board file and support SATA interface additionally.
Specify the dtb file for i.MX6 build.

Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Milo Kim <woogyom.kim@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Common savageboard DT file is used for board support.
Add the vendor name and specify the dtb file for i.MX6Q build.

Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Milo Kim <woogyom.kim@gmail.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

This patch provides support for Liebherr's Monitor 6 board (abverrated as
mccmon6) to Linux kernel.

Signed-off-by: Lukasz Majewski <lukma@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add the DTS file to describe the clearfog pro model - we update the
platform name and compatible string compared to the original version.
The original version remains for compatibility for the time being as
the name of the file has become established, and the machine name
and/or compatible may be used by userspace.

Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>

Add the DTS file to describe the clearfog base model.

Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>

Add socfpga_arria10_socdk_nand.dts board file for supporting NAND.

Signed-off-by: Graham Moore <grmoore@opensource.altera.com>
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
---
v2: move nand dts node to socfpga_arria10.dtsi

SeeedStudio BeagleBone Green Wireless (BBGW) is an expansion of the
SeeedStudio Green (BBG) with the Ethernet replaced by a TI wl1835
wireless module.

This board can be indentified by the GW1x value after A335BNLT (BBB)
in the at24 eeprom:
GW1x [aa 55 33 ee 41 33 33 35  42 4e 4c 54 47 57 31 41  |.U3.A335BNLTGW1A|]

http://beagleboard.org/green-wireless
http://wiki.seeed.cc/BeagleBone_Green_Wireless/

firmware: https://github.com/beagleboard/beaglebone-black-wireless/tree/master/firmware


wl18xx mac address: Stored in at24 eeprom at address 5-16:
hexdump -e '8/1 "%c"' /sys/bus/i2c/devices/0-0050/eeprom | cut -b 5-16

Signed-off-by: Robert Nelson <robertcnelson@gmail.com>
CC: Tony Lindgren <tony@atomide.com>
CC: Jason Kridner <jkridner@beagleboard.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Is.IoT MX6UL modules are system on module solutions manufactured by
Engicam for IOT connectivity applications with following characteristics:
CPU     NXP i.MX6UL (G2) Cortex-A7@528 MHz
RAM     Up to 512 MB LvDDR3@800MT/s
NAND    256MB (option)
eMMC    4GB (option)
LCD     18 bit parallel
BT      2.1+EDR,Bluetooth 3.0, Bluetooth 4.1 (Bluetooth low energy)
WLAN    IEEE 802.11 b/g/n (single stream n)

Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

i.CoreM6 DualLite/Solo modules are system on module solutions manufactured
by Engicam with following characteristics:
CPU           NXP i.MX6 DL, 800MHz
RAM           1GB, 32, 64 bit, DDR3-800/1066
NAND          SLC,512MB
Power supply  Single 5V
MAX LCD RES   FULLHD

and more info at
http://www.engicam.com/en/products/embedded/som/standard/i-core-rqs-m6s-dl-d-q



Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

BeagleBone Black Wireless is clone of the BeagleBone Black (BBB) with
the Ethernet replaced by a TI wl1835 wireless module.

This board can be indentified by the BWAx value after A335BNLT (BBB)
in the at24 eeprom:
BWAx [aa 55 33 ee 41 33 33 35  42 4e 4c 54 42 57 41 35  |.U3.A335BNLTBWA5|]

http://beagleboard.org/black-wireless
https://github.com/beagleboard/beaglebone-black-wireless

firmware: https://github.com/beagleboard/beaglebone-black-wireless/tree/master/firmware


wl18xx mac address: /proc/device-tree/ocp/ethernet@4a100000/slave@4a100200/mac-address

Signed-off-by: Robert Nelson <robertcnelson@gmail.com>
CC: Tony Lindgren <tony@atomide.com>
Acked-by: Jason Kridner <jkridner@beagleboard.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Fixes: ("ab8dd3ae

 ARM: DTS: Add minimal Support for Logic PD
DM3730 SOM-LV")

This adds the dts file into the Makefile. This should have been included in
the original patch.

V2:  Update patch description - same source code
V1:  Original patch

Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Added basic dts support for MicroZed board.

- UART
- SDHCI
- Ethernet

Cc: Soren Brinkmann <soren.brinkmann@xilinx.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Jagan Teki <jteki@openedev.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>

This machine is an open hardware router by cz.nic driven by a
Marvell Armada 385.

Signed-off-by: Uwe Kleine-König <uwe@kleine-koenig.org>
Signed-off-by: Tomas Hlavacek <tmshlvck@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>

Add the initial  device tree for the R8A7745 SoC based SK-RZG1E board.
The board has 1  debug  serial  port (SCIF2); include support for it,
so that the serial console can  work.

Based on the original (and large) patch by Dmitry Shifrin
<dmitry.shifrin@cogentembedded.com>.

Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Add the initial device  tree for the R8A7743 SoC based SK-RZG1M board.
The board has one debug serial port (SCIF0); include support for it, so
that  the serial  console  can work.

Based on the original (and large) patch by Dmitry Shifrin
<dmitry.shifrin@cogentembedded.com>.

Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

The AM571x-IDK board is a board based on TI's AM5718 SOC
which has a single core 1.5GHz A15 processor. This board is a
development platform for the Industrial market with:
- 1GB of DDR3L
- Dual 1Gbps Ethernet
- HDMI,
- PRU-ICSS
- uSD
- 16GB eMMC
- CAN
- RS-485
- PCIe
- USB3.0
- Video Input Port
- Industrial IO port and expansion connector

The link to the data sheet and TRM can be found here:

http://www.ti.com/product/AM5718



Initial support is only for basic peripherals.

Signed-off-by: Schuyler Patton <spatton@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>

The CHIP Pro is a small embeddable board. It features a GR8, an AXP209
PMIC, a 512MB SLC NAND and a WiFi/BT chip.

Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>

Reviews have found that sun5i was a better prefix after all for the GR8.
Rename the relevant device trees before it's too late.

Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

This patch converts my orion5x ls-chl Linkstation device to device tree.

[gregory.clement@free-electrons.com: fix title, add back the commit log,
move the removal of the platform in an other patch]
Signed-off-by: Ashley Hughes <ashley.hughes@blueyonder.co.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>

Add support for the Sierra Wireless MangOH Green board with the
Sierra Wireless WP8548 Module.

Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Andy Gross <andy.gross@linaro.org>

It's BCM4709A0 based device with 16 MiB flash, 128 MiB of RAM and two
PCIe based on-PCB BCM4360 chipsets.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>