ISEE IGEP COM Module is an TI OMAP3 SoC computer on module.

This patch adds an initial device tree support to boot an
IGEP COM Module from the MMC/SD.

Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Tested-by: Enric Balletbo i Serra <eballetbo@gmail.com>
[b-cousson@ti.com: Update the Makefile for 3.8-rc2]
Signed-off-by: Benoit Cousson <benoit.cousson@linaro.org>

ISEE IGEPv2 is an TI OMAP3 SoC based embedded board.

This patch adds an initial device tree support to boot
an IGEPv2 from the MMC/SD.

Currently is working everything that is supported by DT
on OMAP3 SoCs (MMC/SD, GPIO LEDs, EEPROM, TWL4030 audio).

Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Tested-by: Enric Balletbo i Serra <eballetbo@gmail.com>
[benoit.cousson@linaro.org: Update the Makefile for 3.8-rc2]
Signed-off-by: Benoit Cousson <benoit.cousson@linaro.org>

Add a generic .dtsi device tree source file for the
common characteristics across IGEP Technology devices.

Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Acked-by: Matthias Brugger <matthias.bgg@gmail.com>
Tested-by: Enric Balletbo i Serra <eballetbo@gmail.com>
Signed-off-by: Benoit Cousson <benoit.cousson@linaro.org>

Rename I2C and GPIO nodes according to AM33XX TRM. According to
AM33XX TRM device instances are starting from "0" like i2c0, i2c1
and i2c3.

Signed-off-by: Pantelis Antoniou <panto@antoniou-consulting.com>
[panto@antoniou-consulting.com: initial patch by pantelis's]
Signed-off-by: AnilKumar Ch <anilkumar@ti.com>
Signed-off-by: Benoit Cousson <benoit.cousson@linaro.org>

Provide RESET and Power regulators for the USB PHY,
the USB Host port mode and the PHY device.

Also provide pin multiplexer information for USB host
pins.

CC: Benoît Cousson <b-cousson@ti.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Adds device nodes for HS USB Host module, TLL module,
OHCI and EHCI controllers.

CC: Benoît Cousson <b-cousson@ti.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Adds device nodes for HS USB Host module, TLL module,
OHCI and EHCI controllers.

CC: Benoît Cousson <b-cousson@ti.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Fix typo on register address of slink3 controller where register
address is wrongly set as 0x7000d480 but it is 0x7000d800.

Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>

There was only chip enable and readdy/busy pins for the nand controller.
This add the rest of the pins.
pinctrl_nand_16bits contains the specific muxes for 16 bits NANDs.

Signed-off-by: Richard Genoud <richard.genoud@gmail.com>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>

Comments on NAND pins where inverted.

Signed-off-by: Richard Genoud <richard.genoud@gmail.com>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>

The ab8500 device is a child of the prcmu device, which is a memory mapped
bus device, whose children are addressable using physical memory addresses,
not using mailboxes, so a mailbox number in the ab8500 node cannot be
parsed by DT. Nothing uses this number, since it was only introduced
as part of the failed attempt to clean up prcmu mailbox handling, and
we can simply remove it.

Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

This patch adds #dma-cells property to PL330 DMA controller nodes for
supporting generic dma dt bindings on SOCFPGA platform. #dma-channels
and #dma-requests are not required now but added in advance.

Signed-off-by: Padmavathi Venna <padma.v@samsung.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>

The orion5x-lacie-ethernet-disk-mini-v2.dts file was using
"marvell-orion5x-88f5182" as a compatible string, while it should have
been "marvell,orion5x-88f5182".

Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>

There is no need to have a #address-cells property in the MPIC Device
Tree node, and more than that, having it confuses the of_irq_map_raw()
logic, which will be used by the Marvell PCIe driver.

Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>

Setting the reg-io-width to 1 byte represents more accurate
description of the HW.

This will fix an issue where UART driver causes kernel
panic during bootup. Gregory CLEMENT traced the issue to
autoconfig() in 8250.c, where the existence of FIFO is
checked from UART_IIR register. The register is now read as
32-bit value as the reg-io-width is set to 4-bytes. The
retuned value seems to contain bogus data for bits 31:8,
causing the issue.

Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Cc: Gregory CLEMENT <gregory.clement@free-electrons.com>
Cc: Masami Hiramatsu <masami.hiramatsu.pt@hitachi.com>
Tested-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Acked-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Tested-by: Masami Hiramatsu <masami.hiramatsu.pt@hitachi.com>
Tested-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>

The commit:

  48be9ac9 ARM: Dove: split legacy and DT setup

removed the RTC initialization.  This patch re-enables the RTC
via the DT.

Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>

This patch modifies the Armada 370 Reference Design DTS file to enable
support for the two USB ports found on this board.

Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>

The Marvell RTC on Kirkwood makes use of the runit clock. Ensure the
driver clk_prepare_enable() this clock, otherwise there is a danger
the SoC will lockup when accessing RTC registers with the clock
disabled.

Reported-by: Simon Baatz <gmbnomis@gmail.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Simon Baatz <gmbnomis@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>

The kirkwood SoC GPIO cores use the runit clock. Add code to
clk_prepare_enable() runit, otherwise there is a danger of locking up
the SoC by accessing the GPIO registers when runit clock is not
ticking.

Reported-by: Simon Baatz <gmbnomis@gmail.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Simon Baatz <gmbnomis@gmail.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>

When DT support for kirkwood was first introduced, there was no clock
infrastructure.  As a result, we had to manually pass the
clock-frequency to the driver from the device node.

Unfortunately, on kirkwood, with minimal config or all module configs,
clock-frequency breaks booting because of_serial doesn't consume the
gate_clk when clock-frequency is defined.

The end result on kirkwood is that runit gets gated, and then the boot
fails when the kernel tries to write to the serial port.

Fix the issue by removing the clock-frequency parameter from all
kirkwood dts files.

Booted on dreamplug without earlyprintk and successfully logged in via
ttyS0.

Reported-by: Simon Baatz <gmbnomis@gmail.com>
Tested-by: Simon Baatz <gmbnomis@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>

This patch adds #dma-cells property to PL330 DMA controller
nodes for supporting generic dma dt bindings on samsung exynos
platforms. #dma-channels and #dma-requests are not required now
but added in advance.

Signed-off-by: Padmavathi Venna <padma.v@samsung.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>

As DT support for clocks and smp_twd is enabled, add clock entry
for smp_twd clock to DT.

This fixes the following error while booting the kernel:
smp_twd: clock not found -2

Signed-off-by: Prashant Gaikwad <pgaikwad@nvidia.com>
[swarren: include kernel log spew that this fixes]
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>

BCM2835-ARM-Peripherals.pdf states that the I2C module's input clock is
nominally 150MHz, and that value is currently reflected in bcm2835.dtsi.
However, practical measurements show that the rate is actually 250MHz,
and this agrees with various downstream kernels.

Switch the I2C clock's frequency to 250MHz so that the generated bus
clock rate is accurate.

Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Olof Johansson <olof@lixom.net>

According to fsl,imx53-pinctrl.txt, the pin number of DISP1_DAT_21
should be 545, while 543 is IPU_CSI0_D_3.  Along with the change,
one duplication of DISP1_DAT_0 in disp1-grp1 is removed.

Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

The Armada 370 Reference Design board has one SD card slot, directly
connected to the SDIO IP of the SoC, so we enable this IP. there are no
GPIOs for card-detect and write-protect so we do not specify any.

Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>

Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Tested-by: Andrew Lunn <andrew@lunn.ch>

Signed-off-by: Jason Cooper <jason@lakedaemon.net>

Add a DT node for I2C and pinctrl hog for the pins. There appears to
be an i2c bus on topkick with a device on it:

i2cdetect 0
WARNING! This program can confuse your I2C bus, cause data loss and worse!
I will probe file /dev/i2c-0.
I will probe address range 0x03-0x77.
Continue? [Y/n] y
     0  1  2  3  4  5  6  7  8  9  a  b  c  d  e  f
00:          -- -- -- -- -- -- -- -- -- -- -- -- --
10: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- --
20: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- --
30: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- --
40: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- --
50: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- --
60: -- -- -- -- 64 -- -- -- -- -- -- -- -- -- -- --
70: -- -- -- -- -- -- -- --

Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>

Signed-off-by: Jason Cooper <jason@lakedaemon.net>

of_serial now has support for using clocks property and we have
a DT clock provider. This patch replaces the hard coded clock-frequency
property with a clocks phandle to tclk.

Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>

This patch add support for the SPI flash MX25l25635E which is present
on the Armada 370 DB board. This flash stores the bootloader and its
environment.

Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>

This patch add support for the SPI flash M25P64 which is present on
the Armada XP DB board. This flash stores the bootloader and its
environment.

Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>

This patch adds an SPI master device node for Armada XP-GP board.
This master node is an SPI flash controller 'n25q128a13'.

Since there is no 'partitions' node declared, one full sized
partition named as the device will be created.

Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: Lior Amsalem <alior@marvell.com>
Tested-by: Gregory Clement <gregory.clement@free-electrons.com>
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Acked-by: Gregory Clement <gregory.clement@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>

The Armada 370 and Armada XP SoC has an SPI controller.
This patch adds support for this controller in Armada 370
and Armada XP SoC common device tree files.

Note that the Armada XP SPI register length is 0x50 bytes,
while Armada 370 SPI register length is 0x28 bytes,
so we choose the smaller of the two.

Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: Lior Amsalem <alior@marvell.com>
Acked-by: Gregory Clement <gregory.clement@free-electrons.com>
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>

Now that the time-armada-370-xp support local timers, updated the
device tree to take it into account.

Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>

With DT support for orion-ehci also convert Dove to it and
remove the legacy calls and clock aliases.

This patch is based on "ARM: Dove: split legacy and DT setup"
applied to mvebu/boards recently.

Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>

This patch activates every USB port provided by each SoC.
Except for Armada XP Openblocks AX3-4 board,
where we enable only the first two USB ports
until we have more information on the third one usage.

Cc: Lior Amsalem <alior@marvell.com>
Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: Gregory CLEMENT <gregory.clement@free-electrons.com>
Tested-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Tested-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>

The Armada 370 and Armada XP SoC has an Orion EHCI USB controller.
This patch adds support for this controller in Armada 370
and Armada XP SoC common device tree files.

Cc: Lior Amsalem <alior@marvell.com>
Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Tested-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Tested-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>

The OpenBlocks AX3-4 board has one software-controlled button on the
front side, labeled "INIT", so we add minimal support for this button
in the kernel.

Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>

Remove C code and add a Device Tree node in its place.

Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Simon Guinot <simon.guinot@sequanux.org>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>