The panel sends MIPI DCS commands during prepare and is expecting
the bus to remain in LP-11 state in-between.

Set the prepare_upstream_first flag so that the upstream DSI host
is prepared / pre_enabled first, and therefore the bus is in a
defined state.

Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>

mipi_dsi_attach is allowed to fail, and currently the probe
code doesn't clean up (mainly drm_panel_remove) if this happens.

Add cleanup code on failure.

Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>

There is no specific AArch32 driver for the Cortex-A72 PMU, but the
Cortex-A7 one works and is much better than no PMU driver at all.

Signed-off-by: Ben Avison <bavison@riscosopen.org>

Allowing GPIO state to persist allows the use of gpioset to control
GPIO levels without having to use the --mode=wait feature.

Signed-off-by: Phil Elwell <phil@raspberrypi.com>

On some platforms the cma area can be half the entire system memory,
meaning that allocations start happening in the cma area immediately.
This leads to fragmentation and subsequent fatal cma_alloc failures.

We introduce an "alloc_in_cma_threshold" parameter which requires that
this many sixteenths of the free pages must be in cma before it will
try to use them. By default this is set to 12, but the previous
behaviour can be restored by setting it to 8 on startup.

Signed-off-by: David Plowman <david.plowman@raspberrypi.com>

The encoder can skip frames totally should rate control overshoot
the target bitrate too far. In this situation it generates an
output buffer of length 0.
V4L2 treats a buffer of length 0 as an end of stream flag, which is
not appropriate in this case, therefore we can not return that buffer
to the client.

The driver was returning the buffer to videobuf2 in the QUEUED state,
however that buffer was then not dequeued again, so the number of
buffers was reduced each time this happened. In the pathological
case of using GStreamer's videotestsrc in mode 1 for noise, this happens
sufficiently frequently to totally stall the pipeline.

If the port is still enabled then return the buffer straight back to
the VPU rather than to videobuf2.

Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>

Add a "drm" parameter that enables use of the drm/mi0283qt driver instead
of fbtft/fb_ili9341. Also add a "backlight-pwm" parameter that can be used
with the "drm" parameter.

Signed-off-by: Noralf Trønnes <noralf@tronnes.org>

This reverts commit 97d1b136.

The fbtft backlight problem was fixed in 5.15.6 so this workaround has to
be reverted to make backlight work again.

Ref: https://github.com/notro/fbtft/issues/571



Signed-off-by: Noralf Trønnes <noralf@tronnes.org>

Link: https://lore.kernel.org/r/20220325150419.931802116@linuxfoundation.org


Tested-by: Fox Chen <foxhlchen@gmail.com>
Tested-by: Florian Fainelli <f.fainelli@gmail.com>
Tested-by: Shuah Khan <skhan@linuxfoundation.org>
Tested-by: Linux Kernel Functional Testing <lkft@linaro.org>
Tested-by: Ron Economos <re@w6rz.net>
Tested-by: Bagas Sanjaya <bagasdotme@gmail.com>
Tested-by: Sudip Mukherjee <sudip.mukherjee@codethink.co.uk>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 2d327a79 upstream.

My latest patch, attempting to fix the refcount leak in a minimal
way turned out to add a new bug.

Whenever the bind operation fails before we attempt to grab
a reference count on a device, we might release the device refcount
of a prior successful bind() operation.

syzbot was not happy about this [1].

Note to stable teams:

Make sure commit b37a4668 ("netdevice: add the case if dev is NULL")
is already present in your trees.

[1]
general protection fault, probably for non-canonical address 0xdffffc0000000070: 0000 [#1] PREEMPT SMP KASAN
KASAN: null-ptr-deref in range [0x0000000000000380-0x0000000000000387]
CPU: 1 PID: 3590 Comm: syz-executor361 Tainted: G        W         5.17.0-syzkaller-04796-g169e77764adc #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
RIP: 0010:llc_ui_connect+0x400/0xcb0 net/llc/af_llc.c:500
Code: 80 3c 02 00 0f 85 fc 07 00 00 4c 8b a5 38 05 00 00 48 b8 00 00 00 00 00 fc ff df 49 8d bc 24 80 03 00 00 48 89 fa 48 c1 ea 03 <80> 3c 02 00 0f 85 a9 07 00 00 49 8b b4 24 80 03 00 00 4c 89 f2 48
RSP: 0018:ffffc900038cfcc0 EFLAGS: 00010202
RAX: dffffc0000000000 RBX: ffff8880756eb600 RCX: 0000000000000000
RDX: 0000000000000070 RSI: ffffc900038cfe3e RDI: 0000000000000380
RBP: ffff888015ee5000 R08: 0000000000000001 R09: ffff888015ee5535
R10: ffffed1002bdcaa6 R11: 0000000000000000 R12: 0000000000000000
R13: ffffc900038cfe37 R14: ffffc900038cfe38 R15: ffff888015ee5012
FS:  0000555555acd300(0000) GS:ffff8880b9d00000(0000) knlGS:0000000000000000
CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 0000000020000280 CR3: 0000000077db6000 CR4: 00000000003506e0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
Call Trace:
 <TASK>
 __sys_connect_file+0x155/0x1a0 net/socket.c:1900
 __sys_connect+0x161/0x190 net/socket.c:1917
 __do_sys_connect net/socket.c:1927 [inline]
 __se_sys_connect net/socket.c:1924 [inline]
 __x64_sys_connect+0x6f/0xb0 net/socket.c:1924
 do_syscall_x64 arch/x86/entry/common.c:50 [inline]
 do_syscall_64+0x35/0xb0 arch/x86/entry/common.c:80
 entry_SYSCALL_64_after_hwframe+0x44/0xae
RIP: 0033:0x7f016acb90b9
Code: 28 c3 e8 2a 14 00 00 66 2e 0f 1f 84 00 00 00 00 00 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 73 01 c3 48 c7 c1 c0 ff ff ff f7 d8 64 89 01 48
RSP: 002b:00007ffd417947f8 EFLAGS: 00000246 ORIG_RAX: 000000000000002a
RAX: ffffffffffffffda RBX: 0000000000000000 RCX: 00007f016acb90b9
RDX: 0000000000000010 RSI: 0000000020000140 RDI: 0000000000000003
RBP: 00007f016ac7d0a0 R08: 0000000000000000 R09: 0000000000000000
R10: 0000000000000000 R11: 0000000000000246 R12: 00007f016ac7d130
R13: 0000000000000000 R14: 0000000000000000 R15: 0000000000000000
 </TASK>
Modules linked in:
---[ end trace 0000000000000000 ]---
RIP: 0010:llc_ui_connect+0x400/0xcb0 net/llc/af_llc.c:500

Fixes: 764f4eb6

 ("llc: fix netdevice reference leaks in llc_ui_bind()")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Cc: 赵子轩 <beraphin@gmail.com>
Cc: Stoyan Manolov <smanolov@suse.de>
Link: https://lore.kernel.org/r/20220325035827.360418-1-eric.dumazet@gmail.com


Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 8926d88c upstream.

The get_user()/put_user() functions are meant to check for
access_ok(), while the __get_user()/__put_user() functions
don't.

This broke in 4.19 for nds32, when it gained an extraneous
check in __get_user(), but lost the check it needs in
__put_user().

Fixes: 487913ab

 ("nds32: Extract the checking and getting pointer to a macro")
Cc: stable@vger.kernel.org @ v4.19+
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 26509034

 upstream.

While most m68k platforms use separate address spaces for user
and kernel space, at least coldfire does not, and the other
ones have a TASK_SIZE that is less than the entire 4GB address
range.

Using the default implementation of __access_ok() stops coldfire
user space from trivially accessing kernel memory.

Reviewed-by: Christoph Hellwig <hch@lst.de>
Cc: stable@vger.kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 98d504a8 upstream.

The spread of capability between the three WiFi silicon parts wcn36xx
supports is:

wcn3620 - 802.11 a/b/g
wcn3660 - 802.11 a/b/g/n
wcn3680 - 802.11 a/b/g/n/ac

We currently treat wcn3660 as wcn3620 thus limiting it to 2GHz channels.
Fix this regression by ensuring we differentiate between all three parts.

Fixes: 8490987b

 ("wcn36xx: Hook and identify RF_IRIS_WCN3680")
Cc: stable@vger.kernel.org
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Reviewed-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220125004046.4058284-1-bryan.odonoghue@linaro.org


Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit fb5abce6 upstream.

As part of the series conversion to remove nested TPM operations:

https://lore.kernel.org/all/20190205224723.19671-1-jarkko.sakkinen@linux.intel.com/



exposure of the chip->tpm_mutex was removed from much of the upper
level code.  In this conversion, tpm2_del_space() was missed.  This
didn't matter much because it's usually called closely after a
converted operation, so there's only a very tiny race window where the
chip can be removed before the space flushing is done which causes a
NULL deref on the mutex.  However, there are reports of this window
being hit in practice, so fix this by converting tpm2_del_space() to
use tpm_try_get_ops(), which performs all the teardown checks before
acquring the mutex.

Cc: stable@vger.kernel.org # 5.4.x
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Reviewed-by: Jarkko Sakkinen <jarkko@kernel.org>
Signed-off-by: Jarkko Sakkinen <jarkko@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 4a2d4496 upstream.

While commit 6a01afcf ("mac80211: mesh: Free ie data when leaving
mesh") fixed a memory leak on mesh leave / teardown it introduced a
potential memory corruption caused by a double free when rejoining the
mesh:

  ieee80211_leave_mesh()
  -> kfree(sdata->u.mesh.ie);
  ...
  ieee80211_join_mesh()
  -> copy_mesh_setup()
     -> old_ie = ifmsh->ie;
     -> kfree(old_ie);

This double free / kernel panics can be reproduced by using wpa_supplicant
with an encrypted mesh (if set up without encryption via "iw" then
ifmsh->ie is always NULL, which avoids this issue). And then calling:

  $ iw dev mesh0 mesh leave
  $ iw dev mesh0 mesh join my-mesh

Note that typically these commands are not used / working when using
wpa_supplicant. And it seems that wpa_supplicant or wpa_cli are going
through a NETDEV_DOWN/NETDEV_UP cycle between a mesh leave and mesh join
where the NETDEV_UP resets the mesh.ie to NULL via a memcpy of
default_mesh_setup in cfg80211_netdev_notifier_call, which then avoids
the memory corruption, too.

The issue was first observed in an application which was not using
wpa_supplicant but "Senf" instead, which implements its own calls to
nl80211.

Fixing the issue by removing the kfree()'ing of the mesh IE in the mesh
join function and leaving it solely up to the mesh leave to free the
mesh IE.

Cc: stable@vger.kernel.org
Fixes: 6a01afcf

 ("mac80211: mesh: Free ie data when leaving mesh")
Reported-by: Matthias Kretschmer <mathias.kretschmer@fit.fraunhofer.de>
Signed-off-by: Linus Lüssing <ll@simonwunderlich.de>
Tested-by: Mathias Kretschmer <mathias.kretschmer@fit.fraunhofer.de>
Link: https://lore.kernel.org/r/20220310183513.28589-1-linus.luessing@c0d3.blue


Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 222ca305 upstream.

Three architectures check the end of a user access against the
address limit without taking a possible overflow into account.
Passing a negative length or another overflow in here returns
success when it should not.

Use the most common correct implementation here, which optimizes
for a constant 'size' argument, and turns the common case into a
single comparison.

Cc: stable@vger.kernel.org
Fixes: da551281 ("csky: User access")
Fixes: f663b60f ("microblaze: Fix uaccess_ok macro")
Fixes: 7567746e

 ("Hexagon: Add user access functions")
Reported-by: David Laight <David.Laight@aculab.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 10c53578

 upstream.

Currently rcu_preempt_deferred_qs_irqrestore() releases rnp->boost_mtx
before reporting the expedited quiescent state.  Under heavy real-time
load, this can result in this function being preempted before the
quiescent state is reported, which can in turn prevent the expedited grace
period from completing.  Tim Murray reports that the resulting expedited
grace periods can take hundreds of milliseconds and even more than one
second, when they should normally complete in less than a millisecond.

This was fine given that there were no particular response-time
constraints for synchronize_rcu_expedited(), as it was designed
for throughput rather than latency.  However, some users now need
sub-100-millisecond response-time constratints.

This patch therefore follows Neeraj's suggestion (seconded by Tim and
by Uladzislau Rezki) of simply reversing the two operations.

Reported-by: Tim Murray <timmurray@google.com>
Reported-by: Joel Fernandes <joelaf@google.com>
Reported-by: Neeraj Upadhyay <quic_neeraju@quicinc.com>
Reviewed-by: Neeraj Upadhyay <quic_neeraju@quicinc.com>
Reviewed-by: Uladzislau Rezki (Sony) <urezki@gmail.com>
Tested-by: Tim Murray <timmurray@google.com>
Cc: Todd Kjos <tkjos@google.com>
Cc: Sandeep Patil <sspatil@google.com>
Cc: <stable@vger.kernel.org> # 5.4.x
Signed-off-by: Paul E. McKenney <paulmck@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 6b79f96f

 upstream.

If virtio_gpu_object_shmem_init() fails (e.g. due to fault injection, as it
happened in the bug report by syzbot), virtio_gpu_array_put_free() could be
called with objs equal to NULL.

Ensure that objs is not NULL in virtio_gpu_array_put_free(), or otherwise
return from the function.

Cc: stable@vger.kernel.org # 5.13.x
Signed-off-by: Roberto Sassu <roberto.sassu@huawei.com>
Reported-by:  <syzbot+e9072e90624a31dfa85f@syzkaller.appspotmail.com>
Fixes: 377f8331 ("drm/virtio: fix possible leak/unlock virtio_gpu_object_array")
Link: http://patchwork.freedesktop.org/patch/msgid/20211213183122.838119-1-roberto.sassu@huawei.com


Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 1ec7ed51 upstream.

This reverts commit 2dc01659.

Users are reporting regressions in regulatory domain detection and
channel availability.

The problem this was trying to resolve was fixed in firmware anyway:

    QCA6174 hw3.0: sdio-4.4.1: add firmware.bin_WLAN.RMH.4.4.1-00042
    https://github.com/kvalo/ath10k-firmware/commit/4d382787f0efa77dba40394e0bc604f8eff82552

Link: https://bbs.archlinux.org/viewtopic.php?id=254535
Link: http://lists.infradead.org/pipermail/ath10k/2020-April/014871.html
Link: http://lists.infradead.org/pipermail/ath10k/2020-May/015152.html
Link: https://lore.kernel.org/all/1c160dfb-6ccc-b4d6-76f6-4364e0adb6dd@reox.at/
Fixes: 2dc01659

 ("ath: add support for special 0x0 regulatory domain")
Cc: <stable@vger.kernel.org>
Cc: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20200527165718.129307-1-briannorris@chromium.org


Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 2e7b4a32 upstream.

This Realtek device has both wifi and BT components. The latter reports
a USB ID of 0bda:2852, which is not in the table.

BT device description in /sys/kernel/debug/usb/devices contains the following entries:

T: Bus=01 Lev=01 Prnt=01 Port=03 Cnt=02 Dev#= 3 Spd=12 MxCh= 0
D: Ver= 1.00 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=0bda ProdID=2852 Rev= 0.00
S: Manufacturer=Realtek
S: Product=Bluetooth Radio
S: SerialNumber=00e04c000001
C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=500mA
I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms
E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms
I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms
I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms
I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms
I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms
I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms

The missing USB_ID was reported by user trius65 at https://github.com/lwfinger/rtw89/issues/122



Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: stable@vger.kernel.org
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 8893d27f

 upstream.

The implementations of aead and skcipher in the QAT driver do not
support properly requests with the CRYPTO_TFM_REQ_MAY_BACKLOG flag set.
If the HW queue is full, the driver returns -EBUSY but does not enqueue
the request.
This can result in applications like dm-crypt waiting indefinitely for a
completion of a request that was never submitted to the hardware.

To avoid this problem, disable the registration of all crypto algorithms
in the QAT driver by setting the number of crypto instances to 0 at
configuration time.

Cc: stable@vger.kernel.org
Signed-off-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit c844d22f

 upstream.

Clevo NL5xRU and NL5xNU/TUXEDO Aura 15 Gen1 and Gen2 have both a working
native and video interface. However the default detection mechanism first
registers the video interface before unregistering it again and switching
to the native interface during boot. This results in a dangling SBIOS
request for backlight change for some reason, causing the backlight to
switch to ~2% once per boot on the first power cord connect or disconnect
event. Setting the native interface explicitly circumvents this buggy
behaviour by avoiding the unregistering process.

Signed-off-by: Werner Sembach <wse@tuxedocomputers.com>
Cc: All applicable <stable@vger.kernel.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 7dacee0b

 upstream.

For some reason, the Microsoft Surface Go 3 uses the standard ACPI
interface for battery information, but does not use the standard PNP0C0A
HID. Instead it uses MSHW0146 as identifier. Add that ID to the driver
as this seems to work well.

Additionally, the power state is not updated immediately after the AC
has been (un-)plugged, so add the respective quirk for that.

Signed-off-by: Maximilian Luz <luzmaximilian@gmail.com>
Cc: All applicable <stable@vger.kernel.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit e702196b

 upstream.

On this board the ACPI RSDP structure points to both a RSDT and an XSDT,
but the XSDT points to a truncated FADT. This causes all sorts of trouble
and usually a complete failure to boot after the following error occurs:

  ACPI Error: Unsupported address space: 0x20 (*/hwregs-*)
  ACPI Error: AE_SUPPORT, Unable to initialize fixed events (*/evevent-*)
  ACPI: Unable to start ACPI Interpreter

This leaves the ACPI implementation in such a broken state that subsequent
kernel subsystem initialisations go wrong, resulting in among others
mismapped PCI memory, SATA and USB enumeration failures, and freezes.

As this is an older embedded platform that will likely never see any BIOS
updates to address this issue and its default shipping OS only complies to
ACPI 1.0, work around this by forcing `acpi=rsdt`. This patch, applied on
top of Linux 5.10.102, was confirmed on real hardware to fix the issue.

Signed-off-by: Mark Cilissen <mark@yotsuba.nl>
Cc: All applicable <stable@vger.kernel.org>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 6e1acfa3 upstream.

Bail out in case userspace uses unsupported registers.

Fixes: 49499c3e

 ("netfilter: nf_tables: switch registers to 32 bit addressing")
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 4c905f67 upstream.

Initialize registers to avoid stack leak into userspace.

Fixes: 96518518

 ("netfilter: add nftables")
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit e9e6faea upstream.

All packets on ingress (except for jumbo) are terminated with a 4-bytes
CRC checksum. It's the responsability of the driver to strip those 4
bytes. Unfortunately a change dating back to March 2017 re-shuffled some
code and made the CRC stripping code effectively dead.

This change re-orders that part a bit such that the datalen is
immediately altered if needed.

Fixes: 4902a922

 ("drivers: net: xgene: Add workaround for errata 10GE_8/ENET_11")
Cc: stable@vger.kernel.org
Signed-off-by: Stephane Graber <stgraber@ubuntu.com>
Tested-by: Stephane Graber <stgraber@ubuntu.com>
Link: https://lore.kernel.org/r/20220322224205.752795-1-stgraber@ubuntu.com


Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 17aaf019

 upstream.

Tests 72 and 78 for ALSA in kselftest fail due to reading
inconsistent values from some devices on a VirtualBox
Virtual Machine using the snd_intel8x0 driver for the AC'97
Audio Controller device.
Taking for example test number 72, this is what the test reports:
"Surround Playback Volume.0 expected 1 but read 0, is_volatile 0"
"Surround Playback Volume.1 expected 0 but read 1, is_volatile 0"
These errors repeat for each value from 0 to 31.

Taking a look at these error messages it is possible to notice
that the written values are read back swapped.
When the write is performed, these values are initially stored in
an array used to sanity-check them and write them in the pcmreg
array. To write them, the two one-byte values are packed together
in a two-byte variable through bitwise operations: the first
value is shifted left by one byte and the second value is stored in the
right byte through a bitwise OR. When reading the values back,
right shifts are performed to retrieve the previously stored
bytes. These shifts are executed in the wrong order, thus
reporting the values swapped as shown above.

This patch fixes this mistake by reversing the read
operations' order.

Signed-off-by: Giacomo Guiduzzi <guiduzzi.giacomo@gmail.com>
Signed-off-by: Paolo Valente <paolo.valente@linaro.org>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20220322200653.15862-1-guiduzzi.giacomo@gmail.com


Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit c14231cc upstream.

Save and restore CM_REG_AUX_VOL instead of register 0x24 twice on
suspend/resume.

Tested on CMI8738LX.

Fixes: cb60e5f5

 ("[ALSA] cmipci - Add PM support")
Signed-off-by: Jonathan Teh <jonathan.teh@outlook.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/DBAPR04MB7366CB3EA9C8521C35C56E8B920E9@DBAPR04MB7366.eurprd04.prod.outlook.com


Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 0f306cca

 upstream.

For the RODE NT-USB the lowest Playback mixer volume setting mutes the
audio output. But it is not reported as such causing e.g. PulseAudio to
accidentally mute the device when selecting a low volume.

Fix this by applying the existing quirk for this kind of issue when the
device is detected.

Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20220311201400.235892-1-lars@metafoo.de


Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 1f68915b

 upstream.

snd_pcm_reset() is a non-atomic operation, and it's allowed to run
during the PCM stream running.  It implies that the manipulation of
hw_ptr and other parameters might be racy.

This patch adds the PCM stream lock at appropriate places in
snd_pcm_*_reset() actions for covering that.

Cc: <stable@vger.kernel.org>
Reviewed-by: Jaroslav Kysela <perex@perex.cz>
Link: https://lore.kernel.org/r/20220322171325.4355-1-tiwai@suse.de


Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 69534c48

 upstream.

We have no protection against concurrent PCM buffer preallocation
changes via proc files, and it may potentially lead to UAF or some
weird problem.  This patch applies the PCM open_mutex to the proc
write operation for avoiding the racy proc writes and the PCM stream
open (and further operations).

Cc: <stable@vger.kernel.org>
Reviewed-by: Jaroslav Kysela <perex@perex.cz>
Link: https://lore.kernel.org/r/20220322170720.3529-5-tiwai@suse.de


Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 3c3201f8

 upstream.

Like the previous fixes to hw_params and hw_free ioctl races, we need
to paper over the concurrent prepare ioctl calls against hw_params and
hw_free, too.

This patch implements the locking with the existing
runtime->buffer_mutex for prepare ioctls.  Unlike the previous case
for snd_pcm_hw_hw_params() and snd_pcm_hw_free(), snd_pcm_prepare() is
performed to the linked streams, hence the lock can't be applied
simply on the top.  For tracking the lock in each linked substream, we
modify snd_pcm_action_group() slightly and apply the buffer_mutex for
the case stream_lock=false (formerly there was no lock applied)
there.

Cc: <stable@vger.kernel.org>
Reviewed-by: Jaroslav Kysela <perex@perex.cz>
Link: https://lore.kernel.org/r/20220322170720.3529-4-tiwai@suse.de


Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit dca947d4

 upstream.

In the current PCM design, the read/write syscalls (as well as the
equivalent ioctls) are allowed before the PCM stream is running, that
is, at PCM PREPARED state.  Meanwhile, we also allow to re-issue
hw_params and hw_free ioctl calls at the PREPARED state that may
change or free the buffers, too.  The problem is that there is no
protection against those mix-ups.

This patch applies the previously introduced runtime->buffer_mutex to
the read/write operations so that the concurrent hw_params or hw_free
call can no longer interfere during the operation.  The mutex is
unlocked before scheduling, so we don't take it too long.

Cc: <stable@vger.kernel.org>
Reviewed-by: Jaroslav Kysela <perex@perex.cz>
Link: https://lore.kernel.org/r/20220322170720.3529-3-tiwai@suse.de


Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 92ee3c60

 upstream.

Currently we have neither proper check nor protection against the
concurrent calls of PCM hw_params and hw_free ioctls, which may result
in a UAF.  Since the existing PCM stream lock can't be used for
protecting the whole ioctl operations, we need a new mutex to protect
those racy calls.

This patch introduced a new mutex, runtime->buffer_mutex, and applies
it to both hw_params and hw_free ioctl code paths.  Along with it, the
both functions are slightly modified (the mmap_count check is moved
into the state-check block) for code simplicity.

Reported-by: Hu Jiahui <kirin.say@gmail.com>
Cc: <stable@vger.kernel.org>
Reviewed-by: Jaroslav Kysela <perex@perex.cz>
Link: https://lore.kernel.org/r/20220322170720.3529-2-tiwai@suse.de


Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit b7557267

 upstream.

ASUS GA402 requires a workaround to manage the routing of its 4 speakers
like the other ASUS models. Add a corresponding quirk entry to fix it.

Signed-off-by: Jason Zheng <jasonzheng2004@gmail.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20220313092216.29858-1-jasonzheng2004@gmail.com


Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 882bd07f

 upstream.

On a HP 288 Pro G8, the front mic could not be detected.In order to
get it working, the pin configuration needs to be set correctly, and
the ALC671_FIXUP_HP_HEADSET_MIC2 fixup needs to be applied.

Signed-off-by: huangwenhui <huangwenhuia@uniontech.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20220311093836.20754-1-huangwenhuia@uniontech.com


Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 9cb72750

 upstream.

Fixes headset detection on Clevo NP50PNJ.

Signed-off-by: Tim Crawford <tcrawford@system76.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20220307193229.5141-1-tcrawford@system76.com


Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 0c20fce1

 upstream.

Fixes headset detection on Clevo NP70PNJ.

Signed-off-by: Tim Crawford <tcrawford@system76.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20220304170840.3351-1-tcrawford@system76.com


Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>