Initial release for rk3228 sdk board.

Signed-off-by: Jeffy Chen <jeffy.chen@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>

Initial release for rk3228 shared dtsi.

Signed-off-by: Jeffy Chen <jeffy.chen@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>

The card detect pin is currently called sdmcc-cd.
This patch fixes the typo and renames the pin to sdmmc-cd.

Signed-off-by: Matthias Brugger <mbrugger@suse.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>

In general, the logic voltage is affected by ddr frequency factors.
We should fix the correct voltage range since assuemd that we have the
ddr frequency driver in mainline in the future.

AFAIK, the 1.8v voltage is used by the SD3.0 card.

Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>

Rk3288-evb-act8846 and rk3288-evb-rk808 are the power boards of
rk3288-evb, they provide the same power supply interface to the
motherboard. Sort out them, put the public part to rk3288-evb.dtsi,
such as gmac and cpu-supply, leaving only the power section.

Signed-off-by: Chris Zhong <zyw@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>

vcc_wl and vcc_lcd are 2 gpio switches for rk3288-evb-act8846 board.

Signed-off-by: Chris Zhong <zyw@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>

According to the schematic, the name of REG8 should be vcc_tp, rather
than vcca_tp.

Signed-off-by: Chris Zhong <zyw@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>

Add support for the IR receiver present on the R89 board.

Signed-off-by: Heiko Stuebner <heiko@sntech.de>

Minnie provides an elan,ekth3500 touchscreen over the display,
so add the necessary node to enable it.

Signed-off-by: Heiko Stuebner <heiko.stuebner@collabora.com>

Also known as the Asus Chromebit.

Signed-off-by: Chris Zhong <zyw@rock-chips.com>
Tested-by: Caesar Wang <wxt@rock-chips.com>
For the license change:
Acked-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>

Similar to pinky, brain is a development model and probably also
nearing extinction. But to keep pinky from being lonely I'll keep
the two brain boards around as well, especially as they as well
have easily accessible dut-connectors.

Signed-off-by: Heiko Stuebner <heiko.stuebner@collabora.com>
For the license change:
Acked-by: Brian Norris <briannorris@chromium.org>

The edp-24m clock has two possible sources: the 24MHz oscillator as well
as an external 27MHz input. The power-on-default is the 27MHz clock which
is not supplied on all Rockchip boards. While on all current boards and
also all Veyron Chromebooks the bootloader seems to adapt the muxing to
the internal source, this doesn't seem to be the case on headless veyron
devices like brain and mickey making the edp-24m clock an orphan.
On the hardware side the 27m input also is not connected at all.

With the upcoming deferral of orphan-clocks this results in the power-
domain code deferring, as it cannot request the needed clock and if the
synchronous reset is sucessfullat all in this case is also unknown.

So fix that by making sure, the edp-24m clock is muxed to the internal
24MHz oscillator at all times.

Signed-off-by: Heiko Stuebner <heiko.stuebner@collabora.com>

According to a commit on the ChromeOS kernel, the temperature of the Speedy
surface is over skin temperature spec. So adjust the thermal settings
to mimic the ChromeOS tree to stay within these spec limits.

Signed-off-by: Heiko Stuebner <heiko.stuebner@collabora.com>
Reviewed-by: Caesar Wang <wxt@rock-chips.com>

In some cases the machine radiating is very poor,sometime the temperature
is rising very quickly on heavy loading.So we need have more frequent
polling and better granularity.

Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko.stuebner@collabora.com>

Add Crypto node for rk3288 including crypto controller and dma clk.

Signed-off-by: Zain Wang <zain.wang@rock-chips.com>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>

Initial release for rk3036 sdk board.

Signed-off-by: Xing Zheng <zhengxing@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>

Initial release for rk3036 shared dtsi.

Signed-off-by: Xing Zheng <zhengxing@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>

Add support for the IR receiver as present on the Radxa Rock 2 Square
board.

Signed-off-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>

add playback and capture properties to compatible various chips.

Signed-off-by: Sugar Zhang <sugar.zhang@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>

The act8846 on rock2 boards controls the system power, so add the
appropriate property to allow turning off the board.

Signed-off-by: John Keeping <john@metanate.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>

Add an ethernet0 alias for the RK3066/RK3188 mac interface so
that u-boot can find the device-node and fill in the mac address on
boards that support a wired network interface.

Signed-off-by: Heiko Stuebner <heiko@sntech.de>

Add an ethernet0 alias for the RK3288 mac interface so
that u-boot can find the device-node and fill in the mac address on
boards that support a wired network interface.

Signed-off-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>

This reverts commit af19161a,
which breaks the omap3 device tree build due to a wrong reference.

I accidently queued this change via the power supply subsystem while
telling Marek at the same time, that it should go through Tony.
Following that I did miss Stephen's messages about the build failure in
linux-next and since he switched to merging an older snapshot nobody
else noticed the problem in my tree. I didn't notice myself, since I
did not build any device tree files assuming none have changed by me.

Signed-off-by: Sebastian Reichel <sre@kernel.org>
Reported-by: Felipe Balbi <balbi@ti.com>
Tested-by: Felipe Balbi <balbi@ti.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Tested-by: Kevin Hilman <khilman@linaro.org>
Acked-by: Tony Lindgren <tony@atomide.com>

This patch adds DT entries for the LEDs found on the Kirkwood-based
LaCie boards 2Big and 5Big Network v2.

Signed-off-by: Simon Guinot <simon.guinot@sequanux.org>
Acked-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>

This reverts commit d871cd2e as it causes
regression in BBB

Reported-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>

This reverts commit e3faf2b8 as it causes
regression in BBB

Reported-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>

The System Bus Controller block has two register regions,
but having only the second one in a separate node was not nice.

Replace it with a new node with two register regions in it.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Olof Johansson <olof@lixom.net>

Enable building all dtb files when CONFIG_OF_ALL_DTBS is enabled. The dtbs
are not really dependent on a platform being enabled or any other kernel
config, so for testing coverage it is convenient to build all of the dtbs.
This builds all dts files in the tree, not just targets listed. This
is simpler for arm64 which has a bunch of sub-dirs.

Signed-off-by: Rob Herring <robh@kernel.org>
Cc: Russell King <linux@arm.linux.org.uk>

Switch to use the ti,edma3-tpcc and ti,edma3-tptc binding for the eDMA3 and
enable the DMA even crossbar with ti,am335x-edma-crossbar.
With the new bindings boards can customize and tweak the DMA channel
priority to match their needs. With the new binding the memcpy is safe
to be used since with the old binding it was not possible for a driver
to know which channel is allowed to be used as non HW triggered channel.

Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>

Switch to use the ti,edma3-tpcc and ti,edma3-tptc binding for the eDMA3 and
enable the DMA even crossbar with ti,am335x-edma-crossbar.
With the new bindings boards can customize and tweak the DMA channel
priority to match their needs. With the new binding the memcpy is safe
to be used since with the old binding it was not possible for a driver
to know which channel is allowed to be used as non HW triggered channel.

Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>

Add L2 cache controller nodes for all the UniPhier SoC DTSI.
Also, add an L3 cache controller node for PH1-Pro5 DTSI.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Olof Johansson <olof@lixom.net>

This allows the tuning code to run and use higher speeds on capable cards.

Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

The drive/sample clocks can be phase shifted.  The drive clock
could be used in a future patch to adjust hold times.  The sample
clock is used for tuning.

Signed-off-by: Alexandru M Stan <amstan@chromium.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Add aliases to fix the I2C indexes like the other UniPhier boards.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Olof Johansson <olof@lixom.net>

Initial version of DTS for ProXstream2 Vodka board.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>

Initial version of DTS for ProXstream2 Gentil board.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>

Specifying both console and stdout-path is redundant.  Add options
":115200n8" to stdout-path and drop "console=ttyS0,115200".

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>

The change corrects cpu compatible property to a defined one,
see Documentation/devicetree/bindings/arm/cpus.txt

Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>

The change corrects cpu compatible property to a defined one,
see Documentation/devicetree/bindings/arm/cpus.txt

Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>

Adds to the node of the DISP1 power domain the two clocks that need to
be reparented while the domain is powered off:
CLK_MOUT_ACLK200_DISP1_SUB and CLK_MOUT_ACLK300_DISP1_SUB.

Otherwise the state is unknown at power up and the mixer's clocks are
all messed up.

Signed-off-by: Tomeu Vizoso <tomeu.vizoso@collabora.com>
Link: http://lkml.kernel.org/g/561CDC33.7050103@collabora.com


Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>