commit c4295ab0 upstream.

After Commit 3499ba81 ("xen: Fix event channel callback via
INTX/GSI"), xenbus_probe() will be called too early on Arm. This will
recent to a guest hang during boot.

If the hang wasn't there, we would have ended up to call
xenbus_probe() twice (the second time is in xenbus_probe_initcall()).

We don't need to initialize xenbus_probe() early for Arm guest.
Therefore, the call in xen_guest_init() is now removed.

After this change, there is no more external caller for xenbus_probe().
So the function is turned to a static one. Interestingly there were two
prototypes for it.

Cc: stable@vger.kernel.org
Fixes: 3499ba81

 ("xen: Fix event channel callback via INTX/GSI")
Reported-by: Ian Jackson <iwj@xenproject.org>
Signed-off-by: Julien Grall <jgrall@amazon.com>
Reviewed-by: David Woodhouse <dwmw@amazon.co.uk>
Reviewed-by: Stefano Stabellini <sstabellini@kernel.org>
Link: https://lore.kernel.org/r/20210210170654.5377-1-julien@xen.org


Signed-off-by: Juergen Gross <jgross@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

[ Upstream commit 3499ba81

 ]

For a while, event channel notification via the PCI platform device
has been broken, because we attempt to communicate with xenstore before
we even have notifications working, with the xs_reset_watches() call
in xs_init().

We tend to get away with this on Xen versions below 4.0 because we avoid
calling xs_reset_watches() anyway, because xenstore might not cope with
reading a non-existent key. And newer Xen *does* have the vector
callback support, so we rarely fall back to INTX/GSI delivery.

To fix it, clean up a bit of the mess of xs_init() and xenbus_probe()
startup. Call xs_init() directly from xenbus_init() only in the !XS_HVM
case, deferring it to be called from xenbus_probe() in the XS_HVM case
instead.

Then fix up the invocation of xenbus_probe() to happen either from its
device_initcall if the callback is available early enough, or when the
callback is finally set up. This means that the hack of calling
xenbus_probe() from a workqueue after the first interrupt, or directly
from the PCI platform device setup, is no longer needed.

Signed-off-by: David Woodhouse <dwmw@amazon.co.uk>
Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Link: https://lore.kernel.org/r/20210113132606.422794-2-dwmw2@infradead.org


Signed-off-by: Juergen Gross <jgross@suse.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

There are several occurrences of the following pattern:

	for_each_memblock(memory, reg) {
		start = __pfn_to_phys(memblock_region_memory_base_pfn(reg);
		end = __pfn_to_phys(memblock_region_memory_end_pfn(reg));

		/* do something with start and end */
	}

Using for_each_mem_range() iterator is more appropriate in such cases and
allows simpler and cleaner code.

[akpm@linux-foundation.org: fix arch/arm/mm/pmsa-v7.c build]
[rppt@linux.ibm.com: mips: fix cavium-octeon build caused by memblock refactoring]
  Link: http://lkml.kernel.org/r/20200827124549.GD167163@linux.ibm.com



Signed-off-by: Mike Rapoport <rppt@linux.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Baoquan He <bhe@redhat.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Daniel Axtens <dja@axtens.net>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: Emil Renner Berthing <kernel@esmil.dk>
Cc: Hari Bathini <hbathini@linux.ibm.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Cc: Marek Szyprowski <m.szyprowski@samsung.com>
Cc: Max Filippov <jcmvbkbc@gmail.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Michal Simek <monstr@monstr.eu>
Cc: Miguel Ojeda <miguel.ojeda.sandonis@gmail.com>
Cc: Palmer Dabbelt <palmer@dabbelt.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Paul Walmsley <paul.walmsley@sifive.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Stafford Horne <shorne@gmail.com>
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Will Deacon <will@kernel.org>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Link: https://lkml.kernel.org/r/20200818151634.14343-13-rppt@kernel.org


Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Use per_cpu_ptr_to_phys() instead of virt_to_phys() for per-cpu
address conversion.

In xen_starting_cpu(), per-cpu xen_vcpu_info address is converted
to gfn by virt_to_gfn() macro. However, since the virt_to_gfn(v)
assumes the given virtual address is in linear mapped kernel memory
area, it can not convert the per-cpu memory if it is allocated on
vmalloc area.

This depends on CONFIG_NEED_PER_CPU_EMBED_FIRST_CHUNK.
If it is enabled, the first chunk of percpu memory is linear mapped.
In the other case, that is allocated from vmalloc area. Moreover,
if the first chunk of percpu has run out until allocating
xen_vcpu_info, it will be allocated on the 2nd chunk, which is
based on kernel memory or vmalloc memory (depends on
CONFIG_NEED_PER_CPU_KM).

Without this fix and kernel configured to use vmalloc area for
the percpu memory, the Dom0 kernel will fail to boot with following
errors.

[    0.466172] Xen: initializing cpu0
[    0.469601] ------------[ cut here ]------------
[    0.474295] WARNING: CPU: 0 PID: 1 at arch/arm64/xen/../../arm/xen/enlighten.c:153 xen_starting_cpu+0x160/0x180
[    0.484435] Modules linked in:
[    0.487565] CPU: 0 PID: 1 Comm: swapper/0 Not tainted 5.9.0-rc4+ #4
[    0.493895] Hardware name: Socionext Developer Box (DT)
[    0.499194] pstate: 00000005 (nzcv daif -PAN -UAO BTYPE=--)
[    0.504836] pc : xen_starting_cpu+0x160/0x180
[    0.509263] lr : xen_starting_cpu+0xb0/0x180
[    0.513599] sp : ffff8000116cbb60
[    0.516984] x29: ffff8000116cbb60 x28: ffff80000abec000
[    0.522366] x27: 0000000000000000 x26: 0000000000000000
[    0.527754] x25: ffff80001156c000 x24: fffffdffbfcdb600
[    0.533129] x23: 0000000000000000 x22: 0000000000000000
[    0.538511] x21: ffff8000113a99c8 x20: ffff800010fe4f68
[    0.543892] x19: ffff8000113a9988 x18: 0000000000000010
[    0.549274] x17: 0000000094fe0f81 x16: 00000000deadbeef
[    0.554655] x15: ffffffffffffffff x14: 0720072007200720
[    0.560037] x13: 0720072007200720 x12: 0720072007200720
[    0.565418] x11: 0720072007200720 x10: 0720072007200720
[    0.570801] x9 : ffff8000100fbdc0 x8 : ffff800010715208
[    0.576182] x7 : 0000000000000054 x6 : ffff00001b790f00
[    0.581564] x5 : ffff800010bbf880 x4 : 0000000000000000
[    0.586945] x3 : 0000000000000000 x2 : ffff80000abec000
[    0.592327] x1 : 000000000000002f x0 : 0000800000000000
[    0.597716] Call trace:
[    0.600232]  xen_starting_cpu+0x160/0x180
[    0.604309]  cpuhp_invoke_callback+0xac/0x640
[    0.608736]  cpuhp_issue_call+0xf4/0x150
[    0.612728]  __cpuhp_setup_state_cpuslocked+0x128/0x2c8
[    0.618030]  __cpuhp_setup_state+0x84/0xf8
[    0.622192]  xen_guest_init+0x324/0x364
[    0.626097]  do_one_initcall+0x54/0x250
[    0.630003]  kernel_init_freeable+0x12c/0x2c8
[    0.634428]  kernel_init+0x1c/0x128
[    0.637988]  ret_from_fork+0x10/0x18
[    0.641635] ---[ end trace d95b5309a33f8b27 ]---
[    0.646337] ------------[ cut here ]------------
[    0.651005] kernel BUG at arch/arm64/xen/../../arm/xen/enlighten.c:158!
[    0.657697] Internal error: Oops - BUG: 0 [#1] SMP
[    0.662548] Modules linked in:
[    0.665676] CPU: 0 PID: 1 Comm: swapper/0 Tainted: G        W         5.9.0-rc4+ #4
[    0.673398] Hardware name: Socionext Developer Box (DT)
[    0.678695] pstate: 00000005 (nzcv daif -PAN -UAO BTYPE=--)
[    0.684338] pc : xen_starting_cpu+0x178/0x180
[    0.688765] lr : xen_starting_cpu+0x144/0x180
[    0.693188] sp : ffff8000116cbb60
[    0.696573] x29: ffff8000116cbb60 x28: ffff80000abec000
[    0.701955] x27: 0000000000000000 x26: 0000000000000000
[    0.707344] x25: ffff80001156c000 x24: fffffdffbfcdb600
[    0.712718] x23: 0000000000000000 x22: 0000000000000000
[    0.718107] x21: ffff8000113a99c8 x20: ffff800010fe4f68
[    0.723481] x19: ffff8000113a9988 x18: 0000000000000010
[    0.728863] x17: 0000000094fe0f81 x16: 00000000deadbeef
[    0.734245] x15: ffffffffffffffff x14: 0720072007200720
[    0.739626] x13: 0720072007200720 x12: 0720072007200720
[    0.745008] x11: 0720072007200720 x10: 0720072007200720
[    0.750390] x9 : ffff8000100fbdc0 x8 : ffff800010715208
[    0.755771] x7 : 0000000000000054 x6 : ffff00001b790f00
[    0.761153] x5 : ffff800010bbf880 x4 : 0000000000000000
[    0.766534] x3 : 0000000000000000 x2 : 00000000deadbeef
[    0.771916] x1 : 00000000deadbeef x0 : ffffffffffffffea
[    0.777304] Call trace:
[    0.779819]  xen_starting_cpu+0x178/0x180
[    0.783898]  cpuhp_invoke_callback+0xac/0x640
[    0.788325]  cpuhp_issue_call+0xf4/0x150
[    0.792317]  __cpuhp_setup_state_cpuslocked+0x128/0x2c8
[    0.797619]  __cpuhp_setup_state+0x84/0xf8
[    0.801779]  xen_guest_init+0x324/0x364
[    0.805683]  do_one_initcall+0x54/0x250
[    0.809590]  kernel_init_freeable+0x12c/0x2c8
[    0.814016]  kernel_init+0x1c/0x128
[    0.817583]  ret_from_fork+0x10/0x18
[    0.821226] Code: d0006980 f9427c00 cb000300 17ffffea (d4210000)
[    0.827415] ---[ end trace d95b5309a33f8b28 ]---
[    0.832076] Kernel panic - not syncing: Attempted to kill init! exitcode=0x0000000b
[    0.839815] ---[ end Kernel panic - not syncing: Attempted to kill init! exitcode=0x0000000b ]---

Signed-off-by: Masami Hiramatsu <mhiramat@kernel.org>
Reviewed-by: Stefano Stabellini <sstabellini@kernel.org>
Link: https://lore.kernel.org/r/160196697165.60224.17470743378683334995.stgit@devnote2


Signed-off-by: Juergen Gross <jgross@suse.com>

Move more nitty gritty DMA implementation details into the common
internal header.

Signed-off-by: Christoph Hellwig <hch@lst.de>

The VCPUOP_register_runstate_memory_area hypercall takes a virtual
address of a buffer as a parameter. The semantics of the hypercall are
such that the virtual address should always be valid.

When KPTI is enabled and we are running userspace code, the virtual
address is not valid, thus, Linux is violating the semantics of
VCPUOP_register_runstate_memory_area.

Do not call VCPUOP_register_runstate_memory_area when KPTI is enabled.

Signed-off-by: Stefano Stabellini <stefano.stabellini@xilinx.com>
CC: Bertrand Marquis <Bertrand.Marquis@arm.com>
CC: boris.ostrovsky@oracle.com
CC: jgross@suse.com
Link: https://lore.kernel.org/r/20200924234955.15455-1-sstabellini@kernel.org


Reviewed-by: Bertrand Marquis <bertrand.marquis@arm.com>
Signed-off-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>

dma_cache_maint is getting called passing a dma address which could be
different from a physical address.

Add a struct device* parameter to dma_cache_maint.

Translate the dma_addr_t parameter of dma_cache_maint by calling
dma_to_phys. Do it for the first page and all the following pages, in
case of multipage handling.

Signed-off-by: Stefano Stabellini <stefano.stabellini@xilinx.com>
Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Tested-by: Corey Minyard <cminyard@mvista.com>
Tested-by: Roman Shaposhnik <roman@zededa.com>
Link: https://lore.kernel.org/r/20200710223427.6897-11-sstabellini@kernel.org


Signed-off-by: Juergen Gross <jgross@suse.com>

xen_dma_sync_for_cpu, xen_dma_sync_for_device, xen_arch_need_swiotlb are
getting called passing dma addresses. On some platforms dma addresses
could be different from physical addresses. Before doing any operations
on these addresses we need to convert them back to physical addresses
using dma_to_phys.

Move the arch_sync_dma_for_cpu and arch_sync_dma_for_device calls from
xen_dma_sync_for_cpu/device to swiotlb-xen.c, and add a call dma_to_phys
to do address translations there.

dma_cache_maint is fixed by the next patch.

Signed-off-by: Stefano Stabellini <stefano.stabellini@xilinx.com>
Tested-by: Corey Minyard <cminyard@mvista.com>
Tested-by: Roman Shaposhnik <roman@zededa.com>
Acked-by: Juergen Gross <jgross@suse.com>
Link: https://lore.kernel.org/r/20200710223427.6897-10-sstabellini@kernel.org


Signed-off-by: Juergen Gross <jgross@suse.com>

No functional changes. The parameter is unused in this patch but will be
used by next patches.

Signed-off-by: Stefano Stabellini <stefano.stabellini@xilinx.com>
Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Tested-by: Corey Minyard <cminyard@mvista.com>
Tested-by: Roman Shaposhnik <roman@zededa.com>
Link: https://lore.kernel.org/r/20200710223427.6897-6-sstabellini@kernel.org


Signed-off-by: Juergen Gross <jgross@suse.com>

No functional changes. The parameter is unused in this patch but will be
used by next patches.

Signed-off-by: Stefano Stabellini <stefano.stabellini@xilinx.com>
Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Tested-by: Corey Minyard <cminyard@mvista.com>
Tested-by: Roman Shaposhnik <roman@zededa.com>
Link: https://lore.kernel.org/r/20200710223427.6897-5-sstabellini@kernel.org


Signed-off-by: Juergen Gross <jgross@suse.com>

Fix the following sparse warning:

arch/arm64/xen/../../arm/xen/enlighten.c:244: warning: macro
"GRANT_TABLE_PHYSADDR" is not used [-Wunused-macros]

It is an isolated macro, and should be removed when its last user
was deleted in the following commit 3cf4095d

 ("arm/xen: Use
xen_xlate_map_ballooned_pages to setup grant table")

Signed-off-by: Xiaofei Tan <tanxiaofei@huawei.com>
Reviewed-by: Stefano Stabellini <sstabellini@kernel.org>
Signed-off-by: Stefano Stabellini <sstabellini@kernel.org>

Fix the following sparse warning:

arch/arm64/xen/../../arm/xen/enlighten.c:39:19: warning: symbol
'_xen_start_info' was not declared. Should it be static?

Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Jason Yan <yanaijie@huawei.com>
Reviewed-by: Stefano Stabellini <sstabellini@kernel.org>
Link: https://lore.kernel.org/r/20200415084853.5808-1-yanaijie@huawei.com


Signed-off-by: Juergen Gross <jgross@suse.com>

These are pure cache maintainance routines, so drop the unused
struct device argument.

Signed-off-by: Christoph Hellwig <hch@lst.de>
Suggested-by: Daniel Vetter <daniel.vetter@ffwll.ch>

The xen_mm_init is not exported or used outside of the file
it is declared in, so make it static. This fixes the following
sparse warning:

arch/arm/xen/mm.c:136:12: warning: symbol 'xen_mm_init' was not declared. Should it be static?

Signed-off-by: Ben Dooks (Codethink) <ben.dooks@codethink.co.uk>
Reviewed-by: Stefano Stabellini <sstabellini@kernel.org>
Signed-off-by: Juergen Gross <jgross@suse.com>

Include <xen/xen-ops.h> for xen_{create,destroy}_contigous_region
call declarations. Fixes the following sparse warnings:

arch/arm/xen/mm.c:119:5: warning: symbol 'xen_create_contiguous_region' was not declared. Should it be static?
arch/arm/xen/mm.c:131:6: warning: symbol 'xen_destroy_contiguous_region' was not declared. Should it be static?

Signed-off-by: Ben Dooks (Codethink) <ben.dooks@codethink.co.uk>
Reviewed-by: Stefano Stabellini <sstabellini@kernel.org>
Signed-off-by: Juergen Gross <jgross@suse.com>

Today the EFI runtime functions are setup in architecture specific
code (x86 and arm), with the functions themselves living in drivers/xen
as they are not architecture dependent.

As the setup is exactly the same for arm and x86 move the setup to
drivers/xen, too. This at once removes the need to make the single
functions global visible.

Signed-off-by: Juergen Gross <jgross@suse.com>
Reviewed-by: Jan Beulich <jbeulich@suse.com>
[boris: "Dropped EXPORT_SYMBOL_GPL(xen_efi_runtime_setup)"]
Signed-off-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>

arm64 shares some code under arch/arm/xen, including mm.c.
However ZONE_DMA is removed by commit
ad67f5a6

("arm64: replace ZONE_DMA with ZONE_DMA32").

So add a check if CONFIG_ZONE_DMA32 is enabled use __GFP_DMA32.

Signed-off-by: Peng Fan <peng.fan@nxp.com>
Acked-by: Stefano Stabellini <sstabellini@kernel.org>
Signed-off-by: Stefano Stabellini <sstabellini@kernel.org>

HYPERVISOR_platform_op() is an inline function and should not
be exported. Since commit 15bfc234 ("modpost: check for
static EXPORT_SYMBOL* functions"), this causes a warning:

WARNING: "HYPERVISOR_platform_op" [vmlinux] is a static EXPORT_SYMBOL_GPL

Instead, export the underlying function called by the static inline:
HYPERVISOR_platform_op_raw.

Fixes: 15bfc234

 ("modpost: check for static EXPORT_SYMBOL* functions")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Stefano Stabellini <stefano.stabellini@xilinx.com>
Signed-off-by: Stefano Stabellini <sstabellini@kernel.org>

Other parts of the kernel expect these nonblocking EFI callbacks to
exist and crash when running under Xen. Since the implementations of
xen_efi_set_variable() and xen_efi_query_variable_info() do not take any
locks, use them for the nonblocking callbacks too.

Signed-off-by: Ross Lagerwall <ross.lagerwall@citrix.com>
Reviewed-by: Juergen Gross <jgross@suse.com>
Signed-off-by: Juergen Gross <jgross@suse.com>

Now that we know we always have the dma-noncoherent.h helpers available
if we are on an architecture with support for non-coherent devices,
we can just call them directly, and remove the calls to the dma-direct
routines, including the fact that we call the dma_direct_map_page
routines but ignore the value returned from it.  Instead we now have
Xen wrappers for the arch_sync_dma_for_{device,cpu} helpers that call
the special Xen versions of those routines for foreign pages.

Note that the new helpers get the physical address passed in addition
to the dma address to avoid another translation for the local cache
maintainance.  The pfn_valid checks remain on the dma address as in
the old code, even if that looks a little funny.

Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Reviewed-by: Stefano Stabellini <sstabellini@kernel.org>
Acked-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>

These routines are only used by swiotlb-xen, which cannot be modular.

Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Stefano Stabellini <sstabellini@kernel.org>

arm and arm64 can just use xen_swiotlb_dma_ops directly like x86, no
need for a pointer indirection.

Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Julien Grall <julien.grall@arm.com>
Reviewed-by: Stefano Stabellini <sstabellini@kernel.org>

Calculate the required operation in the caller, and pass it directly
instead of recalculating it for each page, and use simple arithmetics
to get from the physical address to Xen page size aligned chunks.

Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Stefano Stabellini <sstabellini@kernel.org>

Use the dma-noncoherent dev_is_dma_coherent helper instead of the home
grown variant.  Note that both are always initialized to the same
value in arch_setup_dma_ops.

Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Julien Grall <julien.grall@arm.com>
Reviewed-by: Stefano Stabellini <sstabellini@kernel.org>

Based on 2 normalized pattern(s):

  this program is free software you can redistribute it and or modify
  it under the terms of the gnu general public license as published by
  the free software foundation either version 2 of the license or at
  your option any later version this program is distributed in the
  hope that it will be useful but without any warranty without even
  the implied warranty of merchantability or fitness for a particular
  purpose see the gnu general public license for more details you
  should have received a copy of the gnu general public license along
  with this program if not see http www gnu org licenses

  this program is free software you can redistribute it and or modify
  it under the terms of the gnu general public license as published by
  the free software foundation either version 2 of the license or at
  your option any later version this program is distributed in the
  hope that it will be useful but without any warranty without even
  the implied warranty of merchantability or fitness for a particular
  purpose see the gnu general public license for more details [based]
  [from] [clk] [highbank] [c] you should have received a copy of the
  gnu general public license along with this program if not see http
  www gnu org licenses

extracted by the scancode license scanner the SPDX license identifier

  GPL-2.0-or-later

has been chosen to replace the boilerplate/reference in 355 file(s).

Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Jilayne Lovejoy <opensource@jilayne.com>
Reviewed-by: Steve Winslow <swinslow@gmail.com>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190519154041.837383322@linutronix.de


Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Add SPDX license identifiers to all Make/Kconfig files which:

 - Have no license information of any form

These files fall under the project license, GPL v2 only. The resulting SPDX
license identifier is:

  GPL-2.0-only

Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Add SPDX license identifiers to all files which:

 - Have no license information of any form

 - Have EXPORT_.*_SYMBOL_GPL inside which was used in the
   initial scan/conversion to ignore the file

These files fall under the project license, GPL v2 only. The resulting SPDX
license identifier is:

  GPL-2.0-only

Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

A new local variable is introduced for accessing p2m entry with lock
protection.

Signed-off-by: Hillf Danton <hdanton@sina.com>
Signed-off-by: Stefano Stabellini <sstabellini@kernel.org>
Reviewed-by: Stefano Stabellini <sstabellini@kernel.org>

Release the newly allocated p2m entry if we detect a duplicate in the RB
tree.

Signed-off-by: Hillf Danton <hdanton@sina.com>
Signed-off-by: Stefano Stabellini <sstabellini@kernel.org>
Reviewed-by: Stefano Stabellini <sstabellini@kernel.org>

Every in-kernel use of this function defined it to KERNEL_DS (either as
an actual define, or as an inline function).  It's an entirely
historical artifact, and long long long ago used to actually read the
segment selector valueof '%ds' on x86.

Which in the kernel is always KERNEL_DS.

Inspired by a patch from Jann Horn that just did this for a very small
subset of users (the ones in fs/), along with Al who suggested a script.
I then just took it to the logical extreme and removed all the remaining
gunk.

Roughly scripted with

   git grep -l '(get_ds())' -- :^tools/ | xargs sed -i 's/(get_ds())/(KERNEL_DS)/'
   git grep -lw 'get_ds' -- :^tools/ | xargs sed -i '/^#define get_ds()/d'

plus manual fixups to remove a few unusual usage patterns, the couple of
inline function cases and to fix up a comment that had become stale.

The 'get_ds()' function remains in an x86 kvm selftest, since in user
space it actually does something relevant.

Inspired-by: Jann Horn <jannh@google.com>
Inspired-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Remove duplicate header which is included twice.

Signed-off-by: Souptick Joarder <jrdr.linux@gmail.com>
Reviewed-by: Oleksandr Andrushchenko <oleksandr_andrushchenko@epam.com>
Acked-by: Stefano Stabellini <sstabellini@kernel.org>
Signed-off-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>

Move remaining definitions and declarations from include/linux/bootmem.h
into include/linux/memblock.h and remove the redundant header.

The includes were replaced with the semantic patch below and then
semi-automated removal of duplicated '#include <linux/memblock.h>

@@
@@
- #include <linux/bootmem.h>
+ #include <linux/memblock.h>

[sfr@canb.auug.org.au: dma-direct: fix up for the removal of linux/bootmem.h]
  Link: http://lkml.kernel.org/r/20181002185342.133d1680@canb.auug.org.au
[sfr@canb.auug.org.au: powerpc: fix up for removal of linux/bootmem.h]
  Link: http://lkml.kernel.org/r/20181005161406.73ef8727@canb.auug.org.au
[sfr@canb.auug.org.au: x86/kaslr, ACPI/NUMA: fix for linux/bootmem.h removal]
  Link: http://lkml.kernel.org/r/20181008190341.5e396491@canb.auug.org.au
Link: http://lkml.kernel.org/r/1536927045-23536-30-git-send-email-rppt@linux.vnet.ibm.com


Signed-off-by: Mike Rapoport <rppt@linux.vnet.ibm.com>
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Acked-by: Michal Hocko <mhocko@suse.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Chris Zankel <chris@zankel.net>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Greentime Hu <green.hu@gmail.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Guan Xuetao <gxt@pku.edu.cn>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: "James E.J. Bottomley" <jejb@parisc-linux.org>
Cc: Jonas Bonn <jonas@southpole.se>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Ley Foon Tan <lftan@altera.com>
Cc: Mark Salter <msalter@redhat.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Matt Turner <mattst88@gmail.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Michal Simek <monstr@monstr.eu>
Cc: Palmer Dabbelt <palmer@sifive.com>
Cc: Paul Burton <paul.burton@mips.com>
Cc: Richard Kuo <rkuo@codeaurora.org>
Cc: Richard Weinberger <richard@nod.at>
Cc: Rich Felker <dalias@libc.org>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Serge Semin <fancer.lancer@gmail.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Vineet Gupta <vgupta@synopsys.com>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

There are some PV specific functions in arch/x86/xen/mmu.c which can be
moved to mmu_pv.c. This in turn enables to build multicalls.c dependent
on CONFIG_XEN_PV.

Signed-off-by: Juergen Gross <jgross@suse.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Cc: xen-devel@lists.xenproject.org
Cc: virtualization@lists.linux-foundation.org
Cc: akataria@vmware.com
Cc: rusty@rustcorp.com.au
Cc: hpa@zytor.com
Link: https://lkml.kernel.org/r/20180828074026.820-3-jgross@suse.com

Use a global variable to store the start flags for both PV and PVH.
This allows the xen_initial_domain macro to work properly on PVH.

Note that ARM is also switched to use the new variable.

Signed-off-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Signed-off-by: Roger Pau Monné <roger.pau@citrix.com>
Reviewed-by: Juergen Gross <jgross@suse.com>
Signed-off-by: Juergen Gross <jgross@suse.com>

My recent Xen patch series introduces a new HYPERVISOR_memory_op to
support direct priv-mapping of certain guest resources (such as ioreq
pages, used by emulators) by a tools domain, rather than having to access
such resources via the guest P2M.

This patch adds the necessary infrastructure to the privcmd driver and
Xen MMU code to support direct resource mapping.

NOTE: The adjustment in the MMU code is partially cosmetic. Xen will now
      allow a PV tools domain to map guest pages either by GFN or MFN, thus
      the term 'mfn' has been swapped for 'pfn' in the lower layers of the
      remap code.

Signed-off-by: Paul Durrant <paul.durrant@citrix.com>
Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Signed-off-by: Juergen Gross <jgross@suse.com>

The grant v2 support was removed from the kernel with
commit 438b33c7

 ("xen/grant-table:
remove support for V2 tables") as the higher memory footprint of v2
grants resulted in less grants being possible for a kernel compared
to the v1 grant interface.

As machines with more than 16TB of memory are expected to be more
common in the near future support of grant v2 is mandatory in order
to be able to run a Xen pv domain at any memory location.

So re-add grant v2 support basically by reverting above commit.

Signed-off-by: Juergen Gross <jgross@suse.com>
Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Signed-off-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>

rwlock.h should not be included directly. Instead linux/splinlock.h
should be included. One thing it does is to break the RT build.

Cc: Stefano Stabellini <sstabellini@kernel.org>
Cc: xen-devel@lists.xenproject.org
Cc: linux-arm-kernel@lists.infradead.org
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Reviewed-by: Stefano Stabellini <sstabellini@kernel.org>
Signed-off-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>

ARM and x86 had duplicated versions of the dma_ops structure, the
only difference is that x86 hasn't wired up the set_dma_mask,
mmap, and get_sgtable ops yet.  On x86 all of them are identical
to the generic version, so they aren't needed but harmless.

All the symbols used only for xen_swiotlb_dma_ops can now be marked
static as well.

Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>

The script "checkpatch.pl" pointed information out like the following.

ERROR: do not use assignment in if condition

Thus fix the affected source code place.

Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Reviewed-by: Stefano Stabellini <sstabellini@kernel.org>

Omit an extra message for a memory allocation failure in this function.

This issue was detected by using the Coccinelle software.

Link: http://events.linuxfoundation.org/sites/events/files/slides/LCJ16-Refactor_Strings-WSang_0.pdf


Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Reviewed-by: Stefano Stabellini <sstabellini@kernel.org>