Adds basic support for Embedded Artists' LPC4357 Developer's Kit. Board
features a LPC4357 Soc, 32 MB SDRAM, 128 MB NAND Flash, 16 MB SPI
Flash, USB and Ethernet.

More information can be found on:
http://www.embeddedartists.com/products/kits/lpc4357_kit.php



Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>

NXP LPC18xx/43xx SoCs are very similar devices and should be able to
share a common base (lpc18xx.dtsi). Diffences between the devices are
put in a dtsi which is specific to that device.

Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>

Tested-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>

Merge "mvebu dt changes for v4.2 (part #1)" from Gregory CLEMENT:

- A series adding support for the Compulab CM-A510
- Add alias for mdio on Armada 38x

* tag 'mvebu-dt-4.2' of git://git.infradead.org/linux-mvebu:
  ARM: mvebu: add alias for mdio on Armada 38x
  ARM: dts: dove: Add Compulab SBC-A510 to Makefile
  ARM: dts: dove: Add proper support for Compulab CM-A510/SBC-A510
  ARM: dts: dove: Remove Compulab CM-A510 from Makefile
  ARM: dts: dove: Add internal i2c multiplexer node

Merge tag 'sti-dt-for-v4.2-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mcoquelin/sti into next/dt

Merge "STi DT updates for v4.2, round 2." from Maxime Coquelin:

Highlights:
-----------
 - Add USB3 support to STiH410 & STiH418
 - Add PWM support to STiH416 & STiH407 family
 - Add restart support to STiH416 & STiH407 family
 - Add PMU support to STiH416 & STiH407 family
 - Reorder includes in STiH407 DT files

* tag 'sti-dt-for-v4.2-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mcoquelin/sti:
  ARM: STi: DT: STih407: Re-order #include <*.dtsi> files
  ARM: STi: Ensure requested STi's SysCfg Controlled IRQs are enabled at boot
  ARM: STi: STiH407: Enable PMU IRQs
  ARM: STi: STiH407: Enable Cortex-A9 PMU support
  ARM: STi: STiH416: Enable PMU IRQs
  ARM: STi: STiH416: Enable Cortex-A9 PMU support
  ARM: STi: STiH416: Add Restart support for STiH416
  ARM: STi: STiH407: Add Restart support for STiH407
  ARM: STi: STiH416-b2020e: Enable PWM on the B2020 Rev-E
  ARM: STi: STiH416: Add DT nodes for PWM
  ARM: STi: STiH416: Add Pinctrl settings for PWM
  ARM: STi: STiH407: Add DT nodes for for PWM
  ARM: DT: STi: STiH418: Enable USB3 port on stih418-b2199.
  ARM: DT: STi: STiH418: Add miphy28lp optional oscillator clock properties
  ARM: DT: STi: stihxxx-b2120: Enable USB3 port on stih407-b2120 and stih410-b2120
  ARM: DT: STi: STiH407: Add dwc3 usb3 DT node.
  ARM: DT: STi: STiH407: Update picophyreset for the usb3 controllers usb2 phy

Merge tag 'rpi-dt-for-armsoc-v4.2' of git://git.kernel.org/pub/scm/linux/kernel/git/rpi/linux-rpi into next/dt

Merge "RaspberryPi Device Tree changes due for v4.2" from Lee Jones:

* tag 'rpi-dt-for-armsoc-v4.2' of git://git.kernel.org/pub/scm/linux/kernel/git/rpi/linux-rpi:
  ARM: bcm2835: dt: Use 0x4 prefix for DMA bus addresses to SDRAM.
  ARM: bcm2835: dt: Add the mailbox to the device tree
  ARM: bcm2835: dt: Fix i2c0 node name
  ARM: bcm2835: dt: Use pinctrl header
  ARM: bcm2835: dt: Add header file for pinctrl constants
  ARM: bcm2835: dt: Add root properties for Raspberry Pi
  ARM: bcm2835: dt: Add vendor prefix for Raspberry Pi

The Ux500 like other Cortex-A9 SoC's has a Snoop Control
Unit (SCU) and a Watchdog in the same address range as
the local timers. Add these to the SoC device tree.

Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>

Merge tag 'renesas-dt-for-v4.2' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/dt

Merge "Renesas ARM Based SoC DT Updates for v4.2" from Simon Horman:

* Enable DMA for HSUSB on r8a7790 and r8a7791 SoCs
* Configure the HOME key as wake-up source on kzm9g board
* Use generic names for device nodes on SH Mobile SoCs and boards
* Add "nor-jedec" compatible value to SH Mobile boards
* Add IRQC clock to r8a73a4, r8a779* SoCs
* Remove MSIOF address from r8a7790 and r8a7791 SoCs

* tag 'renesas-dt-for-v4.2' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas: (31 commits)
  ARM: shmobile: r8a7791: Enable DMA for HSUSB
  ARM: shmobile: r8a7791: add USB-DMAC device nodes
  ARM: shmobile: r8a7790: Enable DMA for HSUSB
  ARM: shmobile: r8a7790: add USB-DMAC device nodes
  ARM: shmobile: kzm9g dts: Configure the HOME key as wake-up source
  ARM: shmobile: koelsch dts: Use generic names for device nodes
  ARM: shmobile: lager dts: Use generic names for device nodes
  ARM: shmobile: bockw dts: Use generic names for device nodes
  ARM: shmobile: koelsch dts: Add "nor-jedec" compatible value
  ARM: shmobile: bockw dts: Add "nor-jedec" compatible value
  ARM: shmobile: lager dts: Add "nor-jedec" compatible value
  ARM: shmobile: bockw-reference dts: Add "nor-jedec" compatible value
  ARM: shmobile: henninger dts: Add "nor-jedec" compatible value
  ARM: shmobile: armadillo800eva dts: Use generic names for device nodes
  ARM: shmobile: marzen dts: Use generic names for device nodes
  ARM: shmobile: kzm9d dts: Use generic names for device nodes
  ARM: shmobile: ape6evm dts: Use generic names for device nodes
  ARM: shmobile: sh73a0 dtsi: Use generic names for device nodes
  ARM: shmobile: r8a7791 dtsi: Use generic names for device nodes
  ARM: shmobile: r8a7790 dtsi: Use generic names for device nodes
  ...

Merge "device-tree pxa update" from Robert Jarzmik:

 - clocks descriptions (pxa27x, pxa3xx)
 - timer descriptions (pxa27x, pxa3xx)
 - IPs which are embedded on the SoC
   - keypad
   - udc (USB client)
   - power I2C

These are amongst the building blocks for future pxa device-tree board
description.

* tag 'pxa-dt-4.2' of https://github.com/rjarzmik/linux:
  ARM: dts: pxa: add pxa-timer to pxa27x and pxa3xx
  ARM: dts: pxa: add pxa27x-keypad to pxa27x
  ARM: dts: pxa: add pxa27x-udc to pxa27x
  ARM: dts: pxa: add clocks
  ARM: dts: pxa: add pwri2c to pxa device-tree

Merge "Device Tree changes" from Florian Fainelli:

New devices:

- Felix adds support for the Buffalo WXR-1900DHP and adds the USB led on Buffalo
  WZR-1750DHP

- Rafal adds support for the SmartRG SR400ac, Asus RT-AC68U and RT-AC56U

New peripheral support:

- Brian adds Device Tree nodes for the Broadcom NAND controller found on
  BCM7xxx, BCM63138 and Cygnus SoCs

- Brian adds Device Tree nodes for the SATA AHCI and PHY controller found on
  BCM7xxx

- I add the Device Tree nodes and bindings documents for bringing-up secondary
  CPUs and timer/syscon-reboot on BCM63138

* tag 'arm-soc/for-4.2/dts' of http://github.com/broadcom/stblinux:
  ARM: BCM5301X: Add DT for Asus RT-AC56U
  ARM: BCM5301X: Add DT for Asus RT-AC68U
  ARM: dts: BCM63xx: Add timer and syscon-reboot nodes
  dt-bindings: Add documentation for the BCM63138 timer and syscon-reboot
  ARM: dts: brcmstb: add nodes for SATA controller and PHY
  ARM: dts: cygnus: Enable NAND support for Cygnus
  ARM: bcm63138: add NAND DT support
  ARM: bcm7445: add NAND to DTS
  ARM: BCM5301X: Add DT for SmartRG SR400ac
  ARM: BCM5301X: Add DT for Buffalo WXR-1900DHP
  ARM: BCM5301X: Add USB LED for Buffalo WZR-1750DHP
  ARM: dts: BCM63xx: Add SMP nodes and required properties
  Documentation: DT: Document SMP DT nodes and properties for BCM63138
  ARM: dts: BCM63xx: Add PMB busses nodes
  Documentation: DT: Add Broadcom BCM63138 PMB binding

This patch fixes a regression where serial is enabled by the first
(board) DTSI, then disabled by the second (SoC) file.  To enable
serial and keep it enabled, we need to include the file which enables
it last.

Reported-by: LAVA [via Peter Griffin <peter.griffin@linaro.org&gt;]>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Maxime Coquelin <maxime.coquelin@st.com>

There exists a tiny MMU, configurable only by the VC (running the
closed firmware), which maps from the ARM's physical addresses to bus
addresses.  These bus addresses determine the caching behavior in the
VC's L1/L2 (note: separate from the ARM's L1/L2) according to the top
2 bits.  The bits in the bus address mean:

From the VideoCore processor:
0x0... L1 and L2 cache allocating and coherent
0x4... L1 non-allocating, but coherent. L2 allocating and coherent
0x8... L1 non-allocating, but coherent. L2 non-allocating, but coherent
0xc... SDRAM alias. Cache is bypassed. Not L1 or L2 allocating or coherent

From the GPU peripherals (note: all peripherals bypass the L1
cache. The ARM will see this view once through the VC MMU):
0x0... Do not use
0x4... L1 non-allocating, and incoherent. L2 allocating and coherent.
0x8... L1 non-allocating, and incoherent. L2 non-allocating, but coherent
0xc... SDRAM alias. Cache is bypassed. Not L1 or L2 allocating or coherent

The 2835 firmware always configures the MMU to turn ARM physical
addresses with 0x0 top bits to 0x4, meaning present in L2 but
incoherent with L1.  However, any bus addresses we were generating in
the kernel to be passed to a device had 0x0 bits.  That would be a
reserved (possibly totally incoherent) value if sent to a GPU
peripheral like USB, or L1 allocating if sent to the VC (like a
firmware property request).  By setting dma-ranges, all of the devices
below it get a dev->dma_pfn_offset, so that dma_alloc_coherent() and
friends return addresses with 0x4 bits and avoid cache incoherency.

This matches the behavior in the downstream 2708 kernel (see
BUS_OFFSET in arch/arm/mach-bcm2708/include/mach/memory.h).

Signed-off-by: Eric Anholt <eric@anholt.net>
Tested-by: Noralf Trønnes <noralf@tronnes.org>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

Signed-off-by: Eric Anholt <eric@anholt.net>
Acked-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

Device tree node names should contain the node's reg property address value.
The i2c0 node was apparently forgotten in commit 25b2f1bd

 (ARM: bcm2835:
node name unit address cleanup).

Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

This patch converts all bcm2835 dts and dtsi files to use the pinctrl
header file.

Reviewed-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

This new header file defines pincontrol constants to use
from bcm2835 DTS files for pincontrol properties option.

Reviewed-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

This patch adds root compatible properties for the following boards:
- Raspberry Pi Model A
- Raspberry Pi Model A+
- Raspberry Pi Model B
- Raspberry Pi Model B (no P5)
- Raspberry Pi Model B rev2
- Raspberry Pi Model B+
- Raspberry Pi Compute Module

Reviewed-by: Stephen Warren <swarren@wwwdotorg.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

Since the prefix is already in use, we need to add it in the
vendor list.

Reviewed-by: Stephen Warren <swarren@wwwdotorg.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>

Add a "brcm,bcm6328-timer" and "syscon-reboot" nodes to allow the
generic syscon-reboot driver to reset a BCM63138 SoC.

Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>

A timer node and a syscon-reboot node are required for software reboot
to work on BCM63138, document these two nodes in the platform binding.

Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>

Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>

Enable NAND support for Broadcom Cygnus SoC

Signed-off-by: Ray Jui <rjui@broadcom.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>

Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Tested-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>

Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>

Update bcm63138.dtsi with the following:

- enable-method for both CPU nodes
- brcm,bcm63138-bootlut node
- resets properties to point to the correct PMB controller to release
  the secondary CPU from reset

Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>

Add binding documentation for the additional nodes and properties
required to get the secondary CPU online on the BCM63138 SoC.

Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>

Add the two BCM63138 PMB busses nodes found on this System-on-a-Chip as
described in their corresponding binding document.

Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>

Add a Device Tree binding for the Broadcom BCM63138 Processor Monitor
Bus, which is an internal bus used to access different power and reset
signals within a BCM63138 System-on-a-Chip.

Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>

Merge tag 'tegra-for-4.2-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into next/dt

Merge "ARM: tegra: Devicetree changes for v4.2-rc1" from Thierry Reding:

Contains a couple of fixes and additions to device tree files. The most
notable change is a fix for a misapplied patch that was only exposed by
a recent change in the regulator subsystem that caused USB to break on
Tegra124 recently.

Other than that there are a more or less random assortment of additions
to enable various features on a couple of boards.

* tag 'tegra-for-4.2-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
  ARM: tegra: Fix hda2codec_2x clock and reset names
  ARM: tegra: Add Tegra30 HDA support
  ARM: tegra: Cardhu device-tree comment spelling fix
  ARM: tegra: venice2: Set min-/max-microvolt for VDD_LED supply
  ARM: tegra: venice2: Mark eMMC as non-removable
  ARM: tegra: jetson-tk1: Enable HDA support
  ARM: tegra: Add missing HDMI +5V regulator
  ARM: tegra: cardhu: Add power and volume keys
  ARM: tegra: Correct which USB controller has the UTMI pad registers

Merge tag 'socfpga_dts_for_v4.2_part_2' of git://git.kernel.org/pub/scm/linux/kernel/git/dinguyen/linux into next/dt

Merge "SoCFPGA update for v4.2 part 2" from Dinh Nguyen:
- Add a DTS node for the A9 SCU

* tag 'socfpga_dts_for_v4.2_part_2' of git://git.kernel.org/pub/scm/linux/kernel/git/dinguyen/linux:
  ARM: socfpga: dts: add the a9-scu node

Merge tag 'v4.2-rockchip-dts1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into next/dt

Merge "ARM: rockchip: dts changes for 4.2" from Heiko Stuebner:

Some misc improvements defining additional supply regulators, enabling
the Cortex-A12 HW PMU on the rk3288 and the tsadc on some more rk3288
boards, as well as some usb properties and marking the radxarock pmic
as system-power-controller.

* tag 'v4.2-rockchip-dts1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
  ARM: dts: rockchip: add system-power-controller to act8846 on radxarock
  ARM: dts: rockchip: add properties for dwc2 usb otg controller
  ARM: dts: rockchip: enable tsadc on rk3288 boards
  ARM: dts: rockchip: add act8846 supplies on rk3288-firefly
  ARM: dts: rockchip: Specify VMMC and VQMMC on rk3288-evb
  ARM: dts: rockchip: Enable Cortex-A12 HW PMU events on rk3288

Add the dts node for the A9 SCU.

Signed-off-by: Dinh Nguyen <dinguyen@opensource.altera.com>

Merge tag 'ux500-v4.2-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson into next/dt

Merge "Ux500 Device Tree changes for the v4.2 series" form Linus Walleij:

Define CPU topology, connect that with CoreSight blocks,
add sensor information to DT boards.

* tag 'ux500-v4.2-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson:
  ARM: ux500: add the sensors to the STUIB board
  ARM: ux500: assign the sensor trigger IRQs
  ARM: ux500: fix lsm303dlh magnetometer compat string
  ARM: ux500: add CoreSight blocks to DTS file
  ARM: ux500: define CPU topology

This adds the device tree data for the LIS331DL and the
AK8974 magnetometer to the STUIB board device tree include
file.

Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

The ST sensors on the Ux500 boards were not utilizing the IRQs
for data ready sample triggers. Enable this by assigning the
right GPIO lines and interrupt lines (when the GPIO lines are
used for IRQs) to the accelerometer, gyro and magnetometer
sensors.

Signed-off-by: Linus Walleij <linus.walleij@linaro.org>