Add items in arch/arm/boot/dt/Makefile to compile the dtb
for mach-mmp.
Change the dts and dtsi file to use #include instead of \include\

Signed-off-by: Chao Xie <chao.xie@marvell.com>
Acked-by: Haojian Zhuang <haojian.zhuang@gmail.com>
Signed-off-by: Michael Turquette <mturquette@linaro.org>

The Parallella board comes with a U-Boot bootloader that loads one of
two predefined FPGA bitstreams before booting the kernel. Both define an
AXI interface to the on-board Epiphany processor.

Enable clocks FCLK0..FCLK3 for the Programmable Logic by default.

Otherwise accessing, e.g., the ESYSRESET register freezes the board,
as seen with the Epiphany SDK tools e-reset and e-hw-rev, using /dev/mem.

Cc: <stable@vger.kernel.org> # 3.17.x
Signed-off-by: Andreas Färber <afaerber@suse.de>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Olof Johansson <olof@lixom.net>

Driver has been there since a while back, but the dts never seems to
have been updated with the node (nor pinctrl). Do so now.

Cc: Matt Porter <mporter@linaro.org>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Olof Johansson <olof@lixom.net>

With legacy booting, the platform init code was taking care of
the configuring of GPIOs. With device tree based booting, things
may or may not work depending what bootloader has configured or
if the legacy platform code gets called.

Let's add support for the pwrdn and reset GPIOs to the smc91x
driver to fix the issues of smc91x not working properly when
booted in device tree mode.

And let's change n900 to use these settings as some versions
of the bootloader do not configure things properly causing
errors.

Reported-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Commit 78b81f46 ("ARM: dts: imx28-evk: Run I2C0 at 400kHz") caused issues
when doing the following sequence in loop:

- Boot the kernel
- Perform audio playback
- Reboot the system via 'reboot' command

In many times the audio card cannot be probed, which causes playback to fail.

After restoring to the original i2c0 frequency of 100kHz there is no such
problem anymore.

This reverts commit 78b81f46

.

Cc: <stable@vger.kernel.org> # 3.16+
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

Without the 3.3V regulator node, the SDMMC driver will give these warnings:

dw_mmc ff704000.dwmmc0: No vmmc regulator found
dw_mmc ff704000.dwmmc0: No vqmmc regulator found

This patch adds the regulator node, and points the SD/MMC to the regulator.

Signed-off-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Reviewed-by: Doug Anderson <dianders@chromium.org>
---
v3: Rename nodes to have schematic-name_regulator and remove "boot-on" and
    "always-on"
v2: Move the regulator nodes to their respective board dts file and
    correctly rename them to match the schematic

Without this patch, the booting the SOCFPGA platform would hang at the
SDMMC driver loading. The issue, debugged by Doug Anderson, turned out
to be that the GPIO bank used by the SD card-detect was not set to
status="okay".

Also update the cd-gpios to point to portb of the &gpio1 GPIO IP.

Suggested-by: Doug Anderson <dianders@chromium.org>
Reviewed-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Dinh Nguyen <dinguyen@opensource.altera.com>
---
v4: Use &gpio1 to set status="okay" and update cd-gpio=&portb
v3: Correctly degugged the issue to be a gpio node not having status="okay"

Since the Synopsys GPIO IP can support multiple ports of varying widths, it
would make more sense to have the GPIO node DTS entry as this:

gpio0: gpio@ff708000{
	porta{
	};
};

Also, this is documented in the snps-dwapb-gpio.txt.

Suggested-by: Doug Anderson <dianders@chromium.org>
Reviewed-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Dinh Nguyen <dinguyen@opensource.altera.com>

PLLB input and output ranges were wrongly copied from at91sam9261 as the
datasheet didn't mention explicitly PLLB. Correct their values.

This fixes USB.

Reported-by: Andreas Henriksson <andreas.henriksson@endian.se>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Tested-by: Andreas Henriksson <andreas.henriksson@endian.se>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>

sed -i 's/}\ ;/};/g'

Signed-off-by: Michal Simek <michal.simek@xilinx.com>

Add the cadence watchdog node to the Zynq devicetree.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>

Add missing reference for memory-controller.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>

Add missing reference for ADC node.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>

By in sync with others node and add also baseaddr
to the node name.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>

Due to dependencies between timer and CPU frequency, only changes by
powers of two are allowed. The clocksource driver prevents other
changes, but with cpufreq and its governors it can result in being
spammed with error messages constantly. Hence, remove the 222 MHz OPP.

Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>

The size of the GEM's register area is only 0x1000 bytes.

Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>

Explicitly set the dr_mode for the second dwc3 controller on the
Arndale Octa board to host mode. This is required to ensure the
controller is initialized in the right mode if the kernel is build
with USB gadget support.

Reported-By: Andreas Faerber <afaerber@suse.de>
Signed-off-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>

In case the optional dr_mode property isn't set in the dwc3 nodes the
the controller will go into OTG mode if both USB host and USB gadget
functionality are enabled in the kernel configuration. Unfortunately
this results in USB not working on exynos5420-peach-pit and
exynos5800-peach-pi with such a kernel configuration unless manually
change the mode. To resolve that explicitly configure the dual role
mode as host.

Signed-off-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Reviewed-by: Andreas Faerber <afaerber@suse.de>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>

CM-QS600 is a APQ8064 based computer on module.
The details are available at
http://compulab.co.il/products/computer-on-modules/cm-qs600/



Signed-off-by: Mike Rapoport <mike.rapoport@gmail.com>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Kumar Gala <galak@codeaurora.org>

This DTS has support for the Sony Xperia Z1 phone (codenamed Honami).
This first version of the DTS supports just a serial console.

Signed-off-by: Tim Bird <tim.bird@sonymobile.com>
Tested-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Kumar Gala <galak@codeaurora.org>

Add SATA PHY and SATA AHCI controller nodes to device tree to enable
generic ahci support on the IPQ8064/AP148 board.

Signed-off-by: Kumar Gala <galak@codeaurora.org>

Fix wrong compatible string of Exynos3250 RTC (Real-Time Clock) dt node.
The RTC of Exynos3250 must need additional source clock (XrtcXTI).

Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

I added smc91x support but turns out we currently do not set the
smc91x timings in gpmc.c but rely on the bootloader timings. This
produces the following error unless the smc91x GPMC timings are
initialized by the bootloader:

Unhandled fault: external abort on non-linefetch (0x1008) at 0xd080630e
...
[<c04067fc>] (smc_drv_probe) from [<c038e9c4>] (platform_drv_probe+0x2c/0x5c)
[<c038e9c4>] (platform_drv_probe) from [<c038d450>] (driver_probe_device+0x104/0x22c)
[<c038d450>] (driver_probe_device) from [<c038d60c>] (__driver_attach+0x94/0x98)
[<c038d60c>] (__driver_attach) from [<c038bc3c>] (bus_for_each_dev+0x54/0x88)
[<c038bc3c>] (bus_for_each_dev) from [<c038cc3c>] (bus_add_driver+0xd8/0x1d8)
[<c038cc3c>] (bus_add_driver) from [<c038dd74>] (driver_register+0x78/0xf4)
[<c038dd74>] (driver_register) from [<c0008924>] (do_one_initcall+0x80/0x1c0)
[<c0008924>] (do_one_initcall) from [<c0852d9c>] (kernel_init_freeable+0x1b8/0x28c)
[<c0852d9c>] (kernel_init_freeable) from [<c05ce86c>] (kernel_init+0x8/0xec)
[<c05ce86c>] (kernel_init) from [<c000e728>] (ret_from_fork+0x14/0x2c)

Let's fix the issue by disabling the smc91x module for now until we
have sorted out the issues in gpmc.c.

Reported-by: Kevin Hilman <khilman@linaro.org>
Tested-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Regulators for MMC2 (SD card) are PVDD_TFLASH_2V8 (LDO19) for vmmc
and PVDD_APIO_MMCOFF_2V8 (LDO13) for vqmmc.  Currently the device
tree entry for MMC2 uses PVDD_PRE_1V8 (LDO10) for vmmc and vqmmc is
not specified.  Fix it.

Without this patch:
- "mmc: dw_mmc: use mmc_regulator_get_supply to handle regulators"
  patch causes a SD card detection to fail
- "mmc: dw_mmc: Support voltage changes" patch causes a boot hang

This patch fixes both above problems.

Suggested-by: Doug Anderson <dianders@google.com>
Cc: Yuvaraj Kumar C D <yuvaraj.cd@samsung.com>
Cc: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Fixes: 01730558

 ("mmc: dw_mmc: Support voltage changes")
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Carlo Caione <carlo@caione.org>

The K2L MDIO io space has different start address.
Hence, fix it to be 0x26200f00 according to TRM.

Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>

The K2E MDIO io space has different start address.
Hence, fix it to be 0x24200f00 according to TRM.

Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>

Keystone supports dma-coherent on USB master and also needs
dma-ranges to specify the hardware alias memory range in which DMA
can be operational.
Such configuration applied for USB0 devices, but It's missed for
USB1 device which is present only in K2E SoC - hence apply it.

Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>

The IO range size is set incorrectly for USB PHY0 deivice
it should be 24 instead of 32. Otherwise, It causes
USB PHY1 probing failure.

Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>

This patch enables the Ethernet port on the Marvell Berlin2Q DMP board.

Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch adds the Ethernet node, enabling the network unit on Berlin
BG2Q SoCs.

Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add the clock tree description for the PXA27x based boards.

Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Mike Turquette <mturquette@linaro.org>

There are 2 MACIDs stored in the control module of the am33xx. These are
read by the cpsw driver if no valid MACID was found in the devicetree.

Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Reviewed-by: Wolfram Sang <wsa@the-dreams.de>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Reviewed-by: Wolfram Sang <wsa@the-dreams.de>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Now that we have a compatible of its own for the mbus clock, switch to it.

Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>

Enable gcov support for ARM based on original patches by David
Singleton and George G. Davis

Riku - updated to patch to current mainline kernel. The patch
has been submitted in 2010, 2012 - for symmetry, now in 2014 too.

https://lwn.net/Articles/390419/
http://marc.info/?l=linux-arm-kernel&m=133823081813044



v2: remove arch/arm/kernel from gcov disabled files

Cc: Andrey Ryabinin <a.ryabinin@samsung.com>
Cc: Naresh Kamboju <naresh.kamboju@linaro.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Riku Voipio <riku.voipio@linaro.org>
Signed-off-by: Vincent Sanders <vincent.sanders@collabora.co.uk>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Apparently most of the newly added nodes had the same problem,
so instead of reverting the individual patches, this undoes
the effect of the merge and backs out all of them at once.

Signed-off-by: Arnd Bergmann <arnd@arndb.de>

This reverts commit 610bd872

.

"ARM: dts: hix5hd2: add wdg node" causes a build breakage due to
an undefined constatns:

Error: arch/arm/boot/dts/hisi-x5hd2.dtsi:374.22-23 syntax error

(Don't you just looove the dtc error messages? They are so informative!)

Signed-off-by: Olof Johansson <olof@lixom.net>

Add dt for rk3288 i2s controller, since i2s clock pins and data pins
default to be GPIO, this patch also add pinctrl to mux them.

Tested on RK3288 board.

Signed-off-by: Jianqun Xu <jay.xu@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>

... for V2M-P1 motherboard CLCD (limited to 640x480 16bpp and using
dedicated video RAM bank) and for V2P-CA9 (up to 1024x768 16bpp).

Signed-off-by: Pawel Moll <pawel.moll@arm.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>