When DEBUG is enabled, do_page_fault() may dereference a NULL pointer,
causing recursive bus errors.

Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>

Cfr. commit 7934779a

 ("Driver-Core: disable
/sbin/hotplug by default").

Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>

Rename RTC_PORT() to ATARI_RTC_PORT(), as the rtc-cmos RTC driver uses the
presence of this macro to enable support for the second NVRAM bank, which
Atari doesn't have ("Unable to handle kernel access at virtual address
00ff8965").

Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>

Since commit d6713b40

 ("m68k: early
parameter support"), the user can specify multiple debug consoles using the
"debug=" kernel command line parameter.
However, as there's only a single struct console object, which is reused,
it would actually register the same console object multiple times, causing
the following warning:

WARNING: CPU: 0 PID: 0 at kernel/printk/printk.c:2233 register_console+0x36/
console 'debug0' already registered

Make sure to register the console object only once, to avoid the warning.

Note that still only one console (the one corresponding to the last
"debug=" parameter) will be active at the same time, as the .write() method
of the already registered console object is overwritten by a subsequent
"debug=" parameter.

Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>

This reduces the kernel image size by ca. 160 KiB.

Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>

Add optional support to export the bootinfo used to boot the kernel in a
"bootinfo" file in procfs.  This is useful with kexec.

This is based on the similar feature for ATAGS on ARM.

Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>

Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>

As reported by Finn Thain, the Mac IIsi ADB driver should be disabled
because it will crash.

Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>

Use the beam position registers, which provide at least 17 bits of data
changing at 1.79 MHz.

Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>

On m68k, get_cycles() (the default implementation for random_get_entropy())
always returns zero, providing no entropy for the random driver.

Add a hook where platforms can provide their own implementation, and wire
it up in the infrastructure provided by commit
61875f30

 ("random: allow architectures to
optionally define random_get_entropy()").

Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>

nf_init() uses virt_to_phys(), which depends on m68k_memoffset being set and
module_fixup() having been called, but this is only done in paging_init().
Hence call paging_init() before nf_init().

This went unnoticed, as virt_to_phys() is a no-op on Atari, unless you start
fiddling with the memory blocks in the bootinfo manually.

Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>

Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>

Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>

Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>

Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>

Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>

Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>

Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>

Move generic definitions used by bootstraps to uapi/asm/bootinfo.h:
  - Machine types,
  - CPU, FPU, and MMU types,
  - struct mem_info.

Keep a copy of struct mem_info for in-kernel use, and rename it to struct
m68k_mem_info, as the exported one will be modified later.

Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>

Export the bootinfo definitions that are used by bootstrap loaders, and
split them up in generic and platform-specific parts.

Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>

Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>

struct mac_booter_data is no longer part of the bootinfo API, hence move it
from <asm/bootinfo.h> to <asm/macintosh.h>, dropping all unused fields in
the process.

Also remove the no longer used mac_booter_data pointer from head.S.

Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>

Drop remainings and API for backwards compatibility with bootinfo interface
version 1.0.  This was used when booting a 2.1.x or newer kernel on Amiga,
Atari, or Mac using a bootstrap for kernel 2.0.x.

Everybody upgraded his bootstrap a long time ago, so this can go.

Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>

Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>

Since the introduction of init sections (which are located after BSS), the
bootinfo is no longer located right after the BSS, but after all kernel
sections.

Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>

Remove the external declarations for m68k_realnum_memory and m68k_memory,
which are already provided by <asm/setup.h>, to avoid conflicts later.

Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>

Fix member definitions for non-native userspace handling:
  - All multi-byte values are big-endian, hence use __be*,
  - All pointers are 32-bit pointers under AmigaOS, but unused (except for
    cd_BoardAddr) under Linux, hence use __be32.

Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>

The Zorro definitions and device IDs are used by bootstraps, hence they
should be exported through UAPI.

Unfortunately zorro.h was never marked for export when headers_install
was introduced, so it was forgotten during the big UAPI disintegration.
In addition, the removal of zorro_ids.h had been sneaked into commit
7e7a43c3

 ("PCI: don't export device IDs to
userspace") before, so it was also forgotten.

Split off and export the Zorro definitions used by bootstraps.

Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>

ZTWO_VADDR() converts from physical to virtual I/O addresses, so it should
return "void __iomem *" instead of "unsigned long".

This allows to drop several casts, but requires adding a few casts to
accomodate legacy driver frameworks that store "unsigned long" I/O
addresses.

Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>

Filling in dev_name of the Zorro bus type and dev.id of each device allows
the driver core to enumerate devices, so we don't have to do that
ourselves.

This changes the names of devices in sysfs from "%02x" to "zorro%u".

Note that filling in dev.id is also needed to support MFD Zorro devices.

Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>

Using an empty static inline function in the CONFIG_ZORRO_NAMES=n case
allows to drop compilation of names.c.

Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>

If the device is not found in the database, it's not needed to fill in
a dummy name. The caller of zorro_name_device() has already taken care
of that to support CONFIG_ZORRO_NAMES=n.

Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>

Currently the array of Zorro devices is allocated statically, wasting
up to 4.5 KiB when running an Amiga or multi-platform kernel on a machine
with no or a handful of Zorro expansion cards. Convert it to conditional
dynamic memory allocation to fix this.

amiga_parse_bootinfo() still needs to store some information about the
detected Zorro devices, at a time even the bootmem allocator is not yet
available.  This is now handled using a much smaller array (typically less
than 0.5 KiB), which is __initdata and thus freed later.

Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>

  - Arch-specific headers were moved to arch/<arch/>/include/asm,
  - APUS support was dropped a long time ago

Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>

Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>

This reduces the kernel image size by ca. 100 KiB, while still allowing
NFS root.

Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>

This is no longer done from iop_init()

Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>

As Sun 3 kernels cannot be multi-platform due to the different Sun 3 MMU
type, it made sense to statically allocate the table to track IOMMU use.

However, Sun 3x kernels can be multi-platform. Furthermore, Sun 3x uses
a larger table than Sun 3 (8192 bytes instead of 512 bytes).

Hence switch to dynamic allocation of this table using the bootmem
allocator to avoid wasting 8192 bytes when not running on a Sun 3x.
As this allocator returns zeroed memory, there's no need to explicitly
initialize the table to zeroes.

Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>

Some functions that are only called (indirectly) from setup_arch() lack
__init annotations.

Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>