The VXLAN neigh_reduce() code is completely non-functional since
check-in. Specific errors:

1) The original code drops all packets with a multicast destination address,
	even though neighbor solicitations are sent to the solicited-node
	address, a multicast address. The code after this check was never run.
2) The neighbor table lookup used the IPv6 header destination, which is the
	solicited node address, rather than the target address from the
	neighbor solicitation. So neighbor lookups would always fail if it
	got this far. Also for L3MISSes.
3) The code calls ndisc_send_na(), which does a send on the tunnel device.
	The context for neigh_reduce() is the transmit path, vxlan_xmit(),
	where the host or a bridge-attached neighbor is trying to transmit
	a neighbor solicitation. To respond to it, the tunnel endpoint needs
	to do a *receive* of the appropriate neighbor advertisement. Doing a
	send, would only try to send the advertisement, encapsulated, to the
	remote destinations in the fdb -- hosts that definitely did not do the
	corresponding solicitation.
4) The code uses the tunnel endpoint IPv6 forwarding flag to determine the
	isrouter flag in the advertisement. This has nothing to do with whether
	or not the target is a router, and generally won't be set since the
	tunnel endpoint is bridging, not routing, traffic.

	The patch below creates a proxy neighbor advertisement to respond to
neighbor solicitions as intended, providing proper IPv6 support for neighbor
reduction.

Signed-off-by: David L Stevens <dlstevens@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Christian Riesch says:

====================
net: davinci_emac: Fix interrupt requests and error handling

since commit 6892b41d (Linux 3.11) the
davinci_emac driver is broken. After doing ifconfig down, ifconfig up,
requesting the interrupts for the driver fails. The interface remains dead
until the board is rebooted.

The first patch in this patchset reverts commit
6892b41d

 partially and makes the driver
useable again.

During the work on the first patch, a number of bugs in the error handling
of the driver's ndo_open code were found. The second patch fixes these bugs.

I believe the first patch meets the rules for stable kernels, I therefore added
the stable tag to this patch. The second patch is just cleanup, the code
that is fixed by this patch is only executed in case of an error.
====================

Signed-off-by: David S. Miller <davem@davemloft.net>

If an error occurs during the initialization in emac_dev_open() (the
driver's ndo_open function), interrupts, DMA descriptors etc. must be freed.
The current rollback code is buggy in several ways.

  1) Freeing the interrupts. The current code will not free all interrupts
     that were requested by the driver. Furthermore,  the code tries to do a
     platform_get_resource(priv->pdev, IORESOURCE_IRQ, -1) in its last
     iteration.

     This patch fixes these bugs.

  2) Wrong order of err: and rollback: labels. If the setup of the PHY in
     the code fails, the interrupts that have been requested before are
     not freed:

        request irq
                if requesting irqs fails, goto rollback
        setup phy
                if phy setup fails, goto err
        return 0

     rollback:
        free irqs
     err:

     This patch brings the code into the correct order.

  3) The code calls napi_enable() and emac_int_enable(), but does not
     undo both in case of an error.

     This patch adds calls of emac_int_disable() and napi_disable() to the
     rollback code.

  4) RX DMA descriptors are not freed in case of an error: Right before
     requesting the irqs, the function creates DMA descriptors for the
     RX channel. These RX descriptors are never freed when we jump to either
     rollback or err.

     This patch adds code for freeing the DMA descriptors in the case of
     an initialization error. This required a modification of
     cpdma_ctrl_stop() in davinci_cpdma.c: We must be able to call this
     function to free the DMA descriptors while the DMA channels are
     in IDLE state (before cpdma_ctlr_start() was called).

Tested on a custom board with the Texas Instruments AM1808.

Signed-off-by: Christian Riesch <christian.riesch@omicron.at>
Signed-off-by: David S. Miller <davem@davemloft.net>

In commit 6892b41d



Author: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Date:   Tue Jun 25 21:24:51 2013 +0530
net: davinci: emac: Convert to devm_* api

the call of request_irq is replaced by devm_request_irq and the call
of free_irq is removed. But since interrupts are requested in
emac_dev_open, doing ifconfig up/down on the board requests the
interrupts again each time, causing devm_request_irq to fail. The
interface is dead until the device is rebooted.

This patch reverts said commit partially: It changes the driver back
to use request_irq instead of devm_request_irq, puts free_irq back in
place, but keeps the remaining changes of the original patch.

Reported-by: Jon Ringle <jon@ringle.org>
Signed-off-by: Christian Riesch <christian.riesch@omicron.at>
Cc: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Neighbor Solicitation is ipv6 protocol, so we should check
skb->protocol with ETH_P_IPV6

Signed-off-by: Li RongQing <roy.qing.li@gmail.com>
Cc: WANG Cong <amwang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Few platforms use external regulator to keep the ethernet MAC supplied.
So, request and enable the regulator for driver functionality.

Fixes: 66fda75f

 (regulator: core: Replace direct ops->disable usage)
Reported-by: Russell King <rmk+kernel@arm.linux.org.uk>
Suggested-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Jesse Gross says:

====================
Open vSwitch

Four small fixes for net/3.14. I realize that these are late in the
cycle - just got back from vacation.
====================

Signed-off-by: David S. Miller <davem@davemloft.net>

Commit 812e44dd

 ("ip6mr: advertise new mfc entries via rtnl") reuses the
function ip6mr_fill_mroute() to notify mfc events.
But this function was used only for dump and thus was always setting the
flag NLM_F_MULTI, which is wrong in case of a single notification.

Libraries like libnl will wait forever for NLMSG_DONE.

CC: Thomas Graf <tgraf@suug.ch>
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Acked-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

Commit 8cd3ac9f

 ("ipmr: advertise new mfc entries via rtnl") reuses the
function ipmr_fill_mroute() to notify mfc events.
But this function was used only for dump and thus was always setting the
flag NLM_F_MULTI, which is wrong in case of a single notification.

Libraries like libnl will wait forever for NLMSG_DONE.

CC: Thomas Graf <tgraf@suug.ch>
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Acked-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

Commit 3ff661c3

 ("net: rtnetlink notify events for FDB NTF_SELF adds and
deletes") reuses the function nlmsg_populate_fdb_fill() to notify fdb events.
But this function was used only for dump and thus was always setting the
flag NLM_F_MULTI, which is wrong in case of a single notification.

Libraries like libnl will wait forever for NLMSG_DONE.

CC: Thomas Graf <tgraf@suug.ch>
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Acked-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

While it is true that getnstimeofday() uses about 40 cycles if TSC
is available, it can use 1600 cycles if hpet is the clocksource.

Switch to get_jiffies_64(), as this is more than enough, and
go back to 60 seconds periods.

Fixes: 8c27bd75

 ("tcp: syncookies: reduce cookie lifetime to 128 seconds")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Florian Westphal <fw@strlen.de>
Acked-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

The documentation for how to use netlink mmap interface is incorrect.
The calls to setsockopt() require an additional argument.

Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

The kernel starts out its "jiffies" timer as 5 minutes below zero, as
shown in include/linux/jiffies.h:

  /*
   * Have the 32 bit jiffies value wrap 5 minutes after boot
   * so jiffies wrap bugs show up earlier.
   */
  #define INITIAL_JIFFIES ((unsigned long)(unsigned int) (-300*HZ))

The loop in ovs_flow_stats_get() starts out with 'used' set to 0, then
takes any "later" time.  This means that for the first five minutes after
boot, flows will always be reported as never used, since 0 is greater than
any time already seen.

Signed-off-by: Ben Pfaff <blp@nicira.com>
Acked-by: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: Jesse Gross <jesse@nicira.com>

Currently, via-rhine fails to call pci_disable_device() for errors
in rhine_init_one().

Reported-by: Huqiu Liu <liuhq11@mails.tsinghua.edu.cn>
Signed-off-by: Roger Luethi <rl@hellgate.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

Use pci_iounmap instead of iounmap when the virtual mapping was done
with pci_iomap. A simplified version of the semantic patch that finds this
issue is as follows: (http://coccinelle.lip6.fr/

)

// <smpl>
@r@
expression addr;
@@
addr = pci_iomap(...)

@rr@
expression r.addr;
@@
* iounmap(addr)
// </smpl>

Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch fixes a NULL pointer dereference in the event of an
skb allocation failure in arp_reduce().

Signed-Off-By: David L Stevens <dlstevens@us.ibm.com>
Acked-by: Cong Wang <cwang@twopensource.com>

Signed-off-by: David S. Miller <davem@davemloft.net>

Michael Chan says:

====================
cnic bug fixes for net-next

Michael Chan (3):
  cnic: Use proper ulp_ops for per device operations.
  cnic,bnx2i,bnx2fc: Fix inconsistent use of page size
  cnic: Update version to 2.5.20 and copyright year.
====================

Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The bnx2/bnx2x rings are made up of linked pages.  However there is an
upper limit on the page size as some the page size settings are 16-bit
in the hardware/firmware interface.  In the current code, some parts
use BNX2_PAGE_SIZE which has a 16K upper limit and some parts use
PAGE_SIZE.  On archs with >= 64K PAGE_SIZE, it generates some compile
warnings.  Define a new CNIC_PAGE_SZIE which has an upper limit of
16K and use it consistently in all relevant parts.

Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: Eddie Wai <eddie.wai@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

For per device operations, cnic needs to dereference the RCU protected
cp->ulp_ops instead of the global cnic_ulp_tbl.  In 2 locations,
cnic_send_nlmsg() and cnic_copy_ulp_stats(), it was referencing the
global table.  If the device has been unregistered and these functions
are still being called (very unlikely scenarios), it could lead to NULL
pointer dereference.

Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This is a context modified revert of commit 6a9612e2
("net: cdc_ncm: remove ncm_parm field") which introduced
a NCM specification violation, causing setup errors for
some devices. These errors resulted in the device and
host disagreeing about shared settings, with complete
failure to communicate as the end result.

The NCM specification require that many of the NCM specific
control reuests are sent only while the NCM Data Interface
is in alternate setting 0. Reverting the commit ensures that
we follow this requirement.

Fixes: 6a9612e2

 ("net: cdc_ncm: remove ncm_parm field")
Reported-and-tested-by: Pasi Kärkkäinen <pasik@iki.fi>
Reported-by: Thomas Schäfer <tschaefer@t-online.de>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>

In ip6_append_data_mtu(), when the xfrm mode is not tunnel(such as
transport),the ipsec header need to be added in the first fragment, so the mtu
will decrease to reserve space for it, then the second fragment come, the mtu
should be turn back, as the commit 0c183379


said.  however, in the commit a493e60ac4bbe2e977e7129d6d8cbb0dd236be, it use
*mtu = min(*mtu, ...) to change the mtu, which lead to the new mtu is alway
equal with the first fragment's. and cannot turn back.

when I test through  ping6 -c1 -s5000 $ip (mtu=1280):
...frag (0|1232) ESP(spi=0x00002000,seq=0xb), length 1232
...frag (1232|1216)
...frag (2448|1216)
...frag (3664|1216)
...frag (4880|164)

which should be:
...frag (0|1232) ESP(spi=0x00001000,seq=0x1), length 1232
...frag (1232|1232)
...frag (2464|1232)
...frag (3696|1232)
...frag (4928|116)

so delete the min() when change back the mtu.

Signed-off-by: Xin Long <lucien.xin@gmail.com>
Fixes: 75a493e6

 ("ipv6: ip6_append_data_mtu did not care about pmtudisc and frag_size")
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

The Kconfig symbol ISDN_CAPI_MIDDLEWARE is only used in capi.c. Setting
it without setting ISDN_CAPI_CAPI20 is therefor useless. Make it depend
on ISDN_CAPI_CAPI20 and put its entry after ISDN_CAPI_CAPI20's entry.

Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Tilman Schmidt <tilman@imap.cc>
Signed-off-by: David S. Miller <davem@davemloft.net>

Steffen Klassert says:

====================
1) Fix a sleep in atomic when pfkey_sadb2xfrm_user_sec_ctx()
   is called from pfkey_compile_policy().
   Fix from Nikolay Aleksandrov.

2) security_xfrm_policy_alloc() can be called in process and atomic
   context. Add an argument to let the callers choose the appropriate
   way. Fix from Nikolay Aleksandrov.
====================

Signed-off-by: David S. Miller <davem@davemloft.net>

commit f280e89a

 (drivers: net: cpsw: fix for cpsw crash when build as modules)
moved cpts_register()/cpts_unregister() to  ndo_open()/ndo_stop(), but failed
to remove cpts_register in cpsw_probe() which leads to a double registration
and the following debug object splat.

[   18.991902] ODEBUG: init active (active state 0) object type: timer_list hint: delayed_work_timer_fn+0x0/0x2c
[   19.082249] [<c0059e80>] (init_timer_key) from [<c04965d4>] (cpts_register+0x1f0/0x2c4)
[   19.090642] [<c04965d4>] (cpts_register) from [<c04931dc>] (cpsw_ndo_open+0x780/0x81c)
[   19.098948] [<c04931dc>] (cpsw_ndo_open) from [<c0599c2c>] (__dev_open+0xb4/0x118)

Signed-off-by: Benedikt Spranger <b.spranger@linutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

1. For the 64 bits dma mask use dma_set_mask_and_coherent instead of
   dma_set_mask and dma_set_coherent_mask.

2. For the 32 bits dma mask dma_set_coherent_mask is only called if
   dma_set_mask fails, which is unusual. Assuming this as a bug, fixes
   it by replacing calls to dma_set_mask and dma_set_coherent_mask by a
   call to dma_set_mask_and_coherent.

Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com>
Tested-by: Jonas Hahnfeld <hahnjo@hahnjo.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

John W. Linville says:

====================
Please pull these last(?) few wireless bits intended for the 3.14
stream.  Each is here to address a problem found with a patch already
merged...

Dave Jones gives us a memory leak fix, for an error path in brcmfmac.

Felix Fietkau moves a small delay to make it actually reachable.

Helmut Schaa fixes an ath9k sequence numbering problem for non-data
frames.

Stanislaw Gruszka reverts an earlier fix that was found to cause
random connection drops on RT5390 PCI adapters
====================

Signed-off-by: David S. Miller <davem@davemloft.net>

Callers of phy_ethtool_get_wol are supposed to provide a properly
cleared struct ethtool_wolinfo. Therefore, fix phy_suspend to clear
it before passing it to phy_ethtool_get_wol.

Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Reviewed-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>

If this is added to the driver files, then maybe it's
appropriate to add to MAINTAINERS as well.

Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pull x86 fixes from Peter Anvin:
 "Two x86 fixes: Suresh's eager FPU fix, and a fix to the NUMA quirk for
  AMD northbridges.

  This only includes Suresh's fix patch, not the "mostly a cleanup"
  patch which had __init issues"

* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/amd/numa: Fix northbridge quirk to assign correct NUMA node
  x86, fpu: Check tsk_used_math() in kernel_fpu_end() for eager FPU

Pull ACPI and power management fixes from Rafael Wysocki:
 "Three of these are regression fixes, for two recent regressions and
  one introduced during the 3.13 cycle, and the fourth one is a working
  version of the fix that had to be reverted last time.

  Specifics:

   - A recent ACPI resources handling fix overlooked the fact that it
     had to update the ACPI PNP subsystem's resources parsing too and
     caused confusing warning messages to be printed during system
     intialization on some systems (with arguably buggy ACPI tables).
     Fix from Zhang Rui.

   - Moving the early ACPI initialization before timekeeping_init()
     earlier in this cycle broke fast TSC calibration on at least one
     system, so it needs to be done later, but still before
     efi_enter_virtual_mode() to allow the EFI initialization to refer
     to ACPI.

   - A change related to code duplication reduction in the cpufreq core
     inadvertently caused cpufreq intialization to fail for some CPUs
     handled by intel_pstate by adding checks that may fail for that
     driver, but aren't even necessary when it is used.  The issue is
     addressed by preventing those checks from run in the configurations
     in which they aren't needed.

   - If the Hardware Reduced ACPI flag is set in the ACPI tables, system
     suspend, hibernation and ACPI power off will only work when special
     sleep control and sleep status registeres are provided (their
     addresses in the ACPI tables are not zero).  If those registers are
     not available, the features in question have no chances to work, so
     they shouldn't even be regarded as supported.  That helps with
     power off in particular, because alternative power off methods may
     be used then and they may actually work"

* tag 'pm+acpi-3.14-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
  ACPI / sleep: Add extra checks for HW Reduced ACPI mode sleep states
  ACPI / init: Invoke early ACPI initialization later
  cpufreq: Skip current frequency initialization for ->setpolicy drivers
  PNP / ACPI: proper handling of ACPI IO/Memory resource parsing failures

Pull device-mapper fixes form Mike Snitzer:
 "Two small fixes for the DM cache target:

   - fix corruption with >2TB fast device due to truncation bug
   - fix access beyond end of origin device due to a partial block"

* tag 'dm-3.14-fixes-4' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm:
  dm cache: fix access beyond end of origin device
  dm cache: fix truncation bug when copying a block to/from >2TB fast device

Merge branch 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless into for-davem

For systems with multiple servers and routed fabric, all
northbridges get assigned to the first server. Fix this by also
using the node reported from the PCI bus. For single-fabric
systems, the northbriges are on PCI bus 0 by definition, which
are on NUMA node 0 by definition, so this is invarient on most
systems.

Tested on fam10h and fam15h single and multi-fabric systems and
candidate for stable.

Signed-off-by: Daniel J Blueman <daniel@numascale.com>
Acked-by: Steffen Persvold <sp@numascale.com>
Acked-by: Borislav Petkov <bp@suse.de>
Cc: <stable@vger.kernel.org>
Link: http://lkml.kernel.org/r/1394710981-3596-1-git-send-email-daniel@numascale.com


Signed-off-by: Ingo Molnar <mingo@kernel.org>

Pull drm fixes from Dave Airlie:
 "Pretty minor set of fixes for radeon, ttm and vmwgfx.  The ttm ones
  are a regression and an oops seen on server chipsets"

* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
  drm/vmwgfx: Fix a surface reference corner-case in legacy emulation mode
  drm/radeon/cik: properly set compute ring status on disable
  drm/radeon/cik: stop the sdma engines in the enable() function
  drm/radeon/cik: properly set sdma ring status on disable
  drm/radeon: fix runpm disabling on non-PX harder
  drm/ttm: don't oops if no invalidate_caches()
  drm/ttm: Work around performance regression with VM_PFNMAP

Pull i2c Kconfig fix from Wolfram Sang.

* 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
  i2c: Remove usage of orphaned symbol OF_I2C

Pull networking fixes from David Miller:
 "I know this is a bit more than you want to see, and I've told the
  wireless folks under no uncertain terms that they must severely scale
  back the extent of the fixes they are submitting this late in the
  game.

  Anyways:

   1) vmxnet3's netpoll doesn't perform the equivalent of an ISR, which
      is the correct implementation, like it should.  Instead it does
      something like a NAPI poll operation.  This leads to crashes.

      From Neil Horman and Arnd Bergmann.

   2) Segmentation of SKBs requires proper socket orphaning of the
      fragments, otherwise we might access stale state released by the
      release callbacks.

      This is a 5 patch fix, but the initial patches are giving
      variables and such significantly clearer names such that the
      actual fix itself at the end looks trivial.

      From Michael S.  Tsirkin.

   3) TCP control block release can deadlock if invoked from a timer on
      an already "owned" socket.  Fix from Eric Dumazet.

   4) In the bridge multicast code, we must validate that the
      destination address of general queries is the link local all-nodes
      multicast address.  From Linus Lüssing.

   5) The x86 BPF JIT support for negative offsets puts the parameter
      for the helper function call in the wrong register.  Fix from
      Alexei Starovoitov.

   6) The descriptor type used for RTL_GIGA_MAC_VER_17 chips in the
      r8169 driver is incorrect.  Fix from Hayes Wang.

   7) The xen-netback driver tests skb_shinfo(skb)->gso_type bits to see
      if a packet is a GSO frame, but that's not the correct test.  It
      should use skb_is_gso(skb) instead.  Fix from Wei Liu.

   8) Negative msg->msg_namelen values should generate an error, from
      Matthew Leach.

   9) at86rf230 can deadlock because it takes the same lock from it's
      ISR and it's hard_start_xmit method, without disabling interrupts
      in the latter.  Fix from Alexander Aring.

  10) The FEC driver's restart doesn't perform operations in the correct
      order, so promiscuous settings can get lost.  Fix from Stefan
      Wahren.

  11) Fix SKB leak in SCTP cookie handling, from Daniel Borkmann.

  12) Reference count and memory leak fixes in TIPC from Ying Xue and
      Erik Hugne.

  13) Forced eviction in inet_frag_evictor() must strictly make sure all
      frags are deleted, otherwise module unload (f.e.  6lowpan) can
      crash.  Fix from Florian Westphal.

  14) Remove assumptions in AF_UNIX's use of csum_partial() (which it
      uses as a hash function), which breaks on PowerPC.  From Anton
      Blanchard.

      The main gist of the issue is that csum_partial() is defined only
      as a value that, once folded (f.e.  via csum_fold()) produces a
      correct 16-bit checksum.  It is legitimate, therefore, for
      csum_partial() to produce two different 32-bit values over the
      same data if their respective alignments are different.

  15) Fix endiannes bug in MAC address handling of ibmveth driver, also
      from Anton Blanchard.

  16) Error checks for ipv6 exthdrs offload registration are reversed,
      from Anton Nayshtut.

  17) Externally triggered ipv6 addrconf routes should count against the
      garbage collection threshold.  Fix from Sabrina Dubroca.

  18) The PCI shutdown handler added to the bnx2 driver can wedge the
      chip if it was not brought up earlier already, which in particular
      causes the firmware to shut down the PHY.  Fix from Michael Chan.

  19) Adjust the sanity WARN_ON_ONCE() in qdisc_list_add() because as
      currently coded it can and does trigger in legitimate situations.
      From Eric Dumazet.

  20) BNA driver fails to build on ARM because of a too large udelay()
      call, fix from Ben Hutchings.

  21) Fair-Queue qdisc holds locks during GFP_KERNEL allocations, fix
      from Eric Dumazet.

  22) The vlan passthrough ops added in the previous release causes a
      regression in source MAC address setting of outgoing headers in
      some circumstances.  Fix from Peter Boström"

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (70 commits)
  ipv6: Avoid unnecessary temporary addresses being generated
  eth: fec: Fix lost promiscuous mode after reconnecting cable
  bonding: set correct vlan id for alb xmit path
  at86rf230: fix lockdep splats
  net/mlx4_en: Deregister multicast vxlan steering rules when going down
  vmxnet3: fix building without CONFIG_PCI_MSI
  MAINTAINERS: add networking selftests to NETWORKING
  net: socket: error on a negative msg_namelen
  MAINTAINERS: Add tools/net to NETWORKING [GENERAL]
  packet: doc: Spelling s/than/that/
  net/mlx4_core: Load the IB driver when the device supports IBoE
  net/mlx4_en: Handle vxlan steering rules for mac address changes
  net/mlx4_core: Fix wrong dump of the vxlan offloads device capability
  xen-netback: use skb_is_gso in xenvif_start_xmit
  r8169: fix the incorrect tx descriptor version
  tools/net/Makefile: Define PACKAGE to fix build problems
  x86: bpf_jit: support negative offsets
  bridge: multicast: enable snooping on general queries only
  bridge: multicast: add sanity check for general query destination
  tcp: tcp_release_cb() should release socket ownership
  ...

The symbol is an orphan, don't depend on it anymore.

Signed-off-by: Richard Weinberger <richard@nod.at>
[wsa: enhanced commit message]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Fixes: 687b81d0 (i2c: move OF helpers into the core)
Cc: stable@kernel.org

* pnp:
  PNP / ACPI: proper handling of ACPI IO/Memory resource parsing failures

* acpi-init:
  ACPI / init: Invoke early ACPI initialization later

* acpi-sleep:
  ACPI / sleep: Add extra checks for HW Reduced ACPI mode sleep states

* pm-cpufreq:
  cpufreq: Skip current frequency initialization for ->setpolicy drivers

If the HW Reduced ACPI mode bit is set in the FADT, ACPICA uses
the optional sleep control and sleep status registers for making
the system enter sleep states (including S5), so it is not possible
to use system sleep states or power it off using ACPI if the HW
Reduced ACPI mode bit is set and those registers are not available.

For this reason, add a new function, acpi_sleep_state_supported(),
checking if the HW Reduced ACPI mode bit is set and whether or not
system sleep states are usable in that case in addition to checking
the return value of acpi_get_sleep_type_data() and make the ACPI
sleep setup routines use that function to check the availability of
system sleep states.

Among other things, this prevents the kernel from attempting to
use ACPI for powering off HW Reduced ACPI systems without the sleep
control and sleep status registers, because ACPI power off doesn't
have a chance to work on them.  That allows alternative power off
mechanisms that may actually work to be used on those systems.  The
affected machines include Dell Venue 8 Pro, Asus T100TA, Haswell
Desktop SDP and Ivy Bridge EP Demo depot.

References: https://bugzilla.kernel.org/show_bug.cgi?id=70931


Reported-by: Adam Williamson <awilliam@redhat.com>
Tested-by: Aubrey Li <aubrey.li@linux.intel.com>
Cc: 3.4+ <stable@vger.kernel.org> # 3.4+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>