Skip to content
  1. Nov 21, 2014
  3. Oct 19, 2014
    • David S. Miller's avatar
      sparc64: Do not define thread fpregs save area as zero-length array. · e2653143
      David S. Miller authored 
      

This breaks the stack end corruption detection facility.

What that facility does it write a magic value to "end_of_stack()"
and checking to see if it gets overwritten.

"end_of_stack()" is "task_thread_info(p) + 1", which for sparc64 is
the beginning of the FPU register save area.

So once the user uses the FPU, the magic value is overwritten and the
debug checks trigger.

Fix this by making the size explicit.

Due to the size we use for the fpsaved[], gsr[], and xfsr[] arrays we
are limited to 7 levels of FPU state saves.  So each FPU register set
is 256 bytes, allocate 256 * 7 for the fpregs area.

Reported-by: default avatarMeelis Roos <mroos@linux.ee>
Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
      e2653143
    • David S. Miller's avatar
      sparc64: Fix corrupted thread fault code. · 84bd6d8b
      David S. Miller authored 
      Every path that ends up at do_sparc64_fault() must install a valid
FAULT_CODE_* bitmask in the per-thread fault code byte.

Two paths leading to the label winfix_trampoline (which expects the
FAULT_CODE_* mask in register %g4) were not doing so:

1) For pre-hypervisor TLB protection violation traps, if we took
   the 'winfix_trampoline' path we wouldn't have %g4 initialized
   with the FAULT_CODE_* value yet.  Resulting in using the
   TLB_TAG_ACCESS register address value instead.

2) In the TSB miss path, when we notice that we are going to use a
   hugepage mapping, but we haven't allocated the hugepage TSB yet, we
   still have to take the window fixup case into consideration and
   in that particular path we leave %g4 not setup properly.

Errors on this sort were largely invisible previously, but after
commit 4ccb9272 ("sparc64: sun4v TLB
error power off events") we now have a fault_code mask bit
(FAULT_CODE_BAD_RA) that triggers due to this bug.

FAULT_CODE_BAD_RA triggers because this bit is set in TLB_TAG_ACCESS
(see #1 above) and thus we get seemingly random bus errors triggered
for user processes.

Fixes: 4ccb9272

 ("sparc64: sun4v TLB error power off events")
Reported-by: default avatarMeelis Roos <mroos@linux.ee>
Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
      84bd6d8b
    • Andy Lutomirski's avatar
      x86,kvm,vmx: Preserve CR4 across VM entry · d974baa3
      Andy Lutomirski authored 
      

CR4 isn't constant; at least the TSD and PCE bits can vary.

TBH, treating CR0 and CR3 as constant scares me a bit, too, but it looks
like it's correct.

This adds a branch and a read from cr4 to each vm entry.  Because it is
extremely likely that consecutive entries into the same vcpu will have
the same host cr4 value, this fixes up the vmcs instead of restoring cr4
after the fact.  A subsequent patch will add a kernel-wide cr4 shadow,
reducing the overhead in the common case to just two memory reads and a
branch.

Signed-off-by: default avatarAndy Lutomirski <luto@amacapital.net>
Acked-by: default avatarPaolo Bonzini <pbonzini@redhat.com>
Cc: stable@vger.kernel.org
Cc: Petr Matousek <pmatouse@redhat.com>
Cc: Gleb Natapov <gleb@kernel.org>
Signed-off-by: default avatarLinus Torvalds <torvalds@linux-foundation.org>
      d974baa3
  5. Oct 17, 2014
  7. Oct 16, 2014
  9. Oct 15, 2014
    • Steve Capper's avatar
      arm: kvm: STRICT_MM_TYPECHECKS fix for user_mem_abort · 3d08c629
      Steve Capper authored 
      Commit:
b8865767

 ARM: KVM: user_mem_abort: support stage 2 MMIO page mapping

introduced some code in user_mem_abort that failed to compile if
STRICT_MM_TYPECHECKS was enabled.

This patch fixes up the failing comparison.

Signed-off-by: default avatarSteve Capper <steve.capper@linaro.org>
Reviewed-by: default avatarKim Phillips <kim.phillips@linaro.org>
Signed-off-by: default avatarChristoffer Dall <christoffer.dall@linaro.org>
      3d08c629
    • Olof Johansson's avatar
      ARM: sunxi_defconfig: enable CONFIG_REGULATOR · 9a2ad529
      Olof Johansson authored 
      Commit 97a13e52

 ('net: phy: mdio-sun4i: don't select REGULATOR') removed
the select of REGULATOR, which means that it now has to be explicitly
enabled in the defconfig or things won't work very well.

In particular, this fixes a problem with SD/MMC not probing on my A31-based
board.

Cc: Beniamino Galvani <b.galvani@gmail.com>
Signed-off-by: default avatarOlof Johansson <olof@lixom.net>
      9a2ad529
    • David S. Miller's avatar
      sparc64: Fix FPU register corruption with AES crypto offload. · f4da3628
      David S. Miller authored 
      

The AES loops in arch/sparc/crypto/aes_glue.c use a scheme where the
key material is preloaded into the FPU registers, and then we loop
over and over doing the crypt operation, reusing those pre-cooked key
registers.

There are intervening blkcipher*() calls between the crypt operation
calls.  And those might perform memcpy() and thus also try to use the
FPU.

The sparc64 kernel FPU usage mechanism is designed to allow such
recursive uses, but with a catch.

There has to be a trap between the two FPU using threads of control.

The mechanism works by, when the FPU is already in use by the kernel,
allocating a slot for FPU saving at trap time.  Then if, within the
trap handler, we try to use the FPU registers, the pre-trap FPU
register state is saved into the slot.  Then at trap return time we
notice this and restore the pre-trap FPU state.

Over the long term there are various more involved ways we can make
this work, but for a quick fix let's take advantage of the fact that
the situation where this happens is very limited.

All sparc64 chips that support the crypto instructiosn also are using
the Niagara4 memcpy routine, and that routine only uses the FPU for
large copies where we can't get the source aligned properly to a
multiple of 8 bytes.

We look to see if the FPU is already in use in this context, and if so
we use the non-large copy path which only uses integer registers.

Furthermore, we also limit this special logic to when we are doing
kernel copy, rather than a user copy.

Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
      f4da3628
    • Iyappan Subramanian's avatar
      dtb: Add SGMII based 1GbE node to APM X-Gene SoC device tree · 4c2e7f09
      Iyappan Subramanian authored 
      

Signed-off-by: default avatarIyappan Subramanian <isubramanian@apm.com>
Signed-off-by: default avatarKeyur Chudgar <kchudgar@apm.com>
Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
      4c2e7f09
    • Alexei Starovoitov's avatar
      x86: bpf_jit: fix two bugs in eBPF JIT compiler · e0ee9c12
      Alexei Starovoitov authored 
      1.
JIT compiler using multi-pass approach to converge to final image size,
since x86 instructions are variable length. It starts with large
gaps between instructions (so some jumps may use imm32 instead of imm8)
and iterates until total program size is the same as in previous pass.
This algorithm works only if program size is strictly decreasing.
Programs that use LD_ABS insn need additional code in prologue, but it
was not emitted during 1st pass, so there was a chance that 2nd pass would
adjust imm32->imm8 jump offsets to the same number of bytes as increase in
prologue, which may cause algorithm to erroneously decide that size converged.
Fix it by always emitting largest prologue in the first pass which
is detected by oldproglen==0 check.
Also change error check condition 'proglen != oldproglen' to fail gracefully.

2.
while staring at the code realized that 64-byte buffer may not be enough
when 1st insn is large, so increase it to 128 to avoid buffer overflow
(theoretical maximum size of prologue+div is 109) and add runtime check.

Fixes: 62258278

 ("net: filter: x86: internal BPF JIT")
Reported-by: default avatarDarrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: default avatarAlexei Starovoitov <ast@plumgrid.com>
Tested-by: default avatarDarrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
      e0ee9c12
  11. Oct 14, 2014
  13. Oct 13, 2014
  15. Oct 12, 2014
    • Helge Deller's avatar
      parisc: Reduce SIGRTMIN from 37 to 32 to behave like other Linux architectures · 1f25df2e
      Helge Deller authored 
      This patch reduces the value of SIGRTMIN on PARISC from 37 to 32, thus
increasing the number of available RT signals and bring it in sync with other
Linux architectures.

Historically we wanted to natively support HP-UX 32bit binaries with the
PA-RISC Linux port.  Because of that we carried the various available signals
from HP-UX (e.g. SIGEMT and SIGLOST) and folded them in between the native
Linux signals.  Although this was the right decision at that time, this
required us to increase SIGRTMIN to at least 37 which left us with 27 (64-37)
RT signals.

Those 27 RT signals haven't been a problem in the past, but with the upcoming
importance of systemd we now got the problem that systemd alloctes (hardcoded)
signals up to SIGRTMIN+29 which is beyond our NSIG of 64. Because of that we
have not been able to use systemd on the PARISC Linux port yet.

Of course we could ask the systemd developers to not use those hardcoded
values, but this change is very unlikely, esp. with PA-RISC being a niche
architecture.

The other possibility would be to increase NSIG to e.g. 128, but this would
mean to duplicate most of the existing Linux signal handling code into the
parisc specific Linux kernel tree which would most likely introduce lots of new
bugs beside the code duplication.

The third option is to drop some HP-UX signals and shuffle some other signals
around to bring SIGRTMIN to 32.  This is of course an ABI change, but testing
has shown that existing Linux installations are not visibly affected by this
change - most likely because we move those signals around which are rarely used
and move them to slots which haven't been used in Linux yet. In an existing
installation I was able to exchange either the Linux kernel or glibc (or both)
without affecting the boot process and installed applications.

Dropping the HP-UX signals isn't an issue either, since support for HP-UX was
basically dropped a few months back with Kernel 3.14 in commit
f5a408d5

 already, when we changed EWOULDBLOCK
to be equal to EAGAIN.

So, even if this is an ABI change, it's better to change it now and thus bring
PARISC Linux in sync with other architectures to avoid other issues in the
future.

Signed-off-by: default avatarHelge Deller <deller@gmx.de>
Cc: Carlos O'Donell <carlos@systemhalted.org>
Cc: John David Anglin <dave.anglin@bell.net>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Cc: Aaro Koskinen <aaro.koskinen@iki.fi>
Cc: PARISC Linux Kernel Mailinglist <linux-parisc@vger.kernel.org>
Tested-by: default avatarAaro Koskinen <aaro.koskinen@iki.fi>
      1f25df2e