This machine is based on I2SE's Duckbill 2 board and features a
EnOcean daugther board based on the popular TCM310 chipset.
This product is intended to be used for e.g. home automation purposes.

Signed-off-by: Michael Heimpold <mhei@heimpold.de>
Cc: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

This machine is based on I2SE's Duckbill 2 board and features a
RS-485 daugther board. This device is intended to be used for
e.g. home automation purposes.

Signed-off-by: Michael Heimpold <mhei@heimpold.de>
Cc: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

This machine is an USB pen drive sized development board,
based on NXP's i.MX28 CPU. In contrast to the previous
model "Duckbill", the "Duckbill 2" series has internal
eMMC storage.

Signed-off-by: Michael Heimpold <mhei@heimpold.de>
Cc: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

This patch updates the Duckbill device tree and synchronize it with
the vendor distributed file. The changes in mostly pin-muxing stuff,
but also some minor fixes. In detail:
- enable SPI pins
- enable I2C pins
- enable UART pins
- enable LRADC pin
- adjust USB DR mode
- add default triggers for LEDs
- get rid of regulators simple-bus container
- adjust phy reset duration
  According to phy datasheet, 25ms are sufficient. This also reduces
  the time to boot the system.

Signed-off-by: Michael Heimpold <mhei@heimpold.de>
Cc: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Signed-off-by: Michael Heimpold <michael.heimpold@i2se.com>
Cc: Stefan Wahren <stefan.wahren@i2se.com>
Acked-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

This patch renames mmc2_sck_cfg in order to prepare for an alternative
muxing setup.

Signed-off-by: Michael Heimpold <michael.heimpold@i2se.com>
Cc: Stefan Wahren <stefan.wahren@i2se.com>
Acked-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Signed-off-by: Michael Heimpold <michael.heimpold@i2se.com>
Cc: Stefan Wahren <stefan.wahren@i2se.com>
Acked-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Quoting Philipp Zabel:
"Since this regulator is used as the TVDAC analog power supply, this
range should at least be limited to the analog power supply range of the
TVDAC, listed in Table 74-9. of the i.MX53 reference manual (2.5-2.75V).

But since the nominal voltage is 2.75V, which was used to determine the
analog gain that is supposed to result in the necessary 0.7V
peak-to-peak amplitude on the VGA output, I'd say we should just fix the
voltage to 2750000 here."

, so limit the TVDAC analog power supply as suggested.

Suggested-by: Lucas Stach <l.stach@pengutronix.de>
Suggested-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

imx6ul.dtsi already contains:

cpu0: cpu@0 {
	....
	arm-supply = <&reg_arm>;
	soc-supply = <&reg_soc>;
};

, so remove the duplication.

Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

The cm-fx6 module has an onboard Wolfson wm8731 codec which is muxed
to the ssi2 controller. Unlike most (all?) supported i.MX6 board/codec
combinations the wm8731 is operated in slave mode and the clock setup
is static.

Add support for it.

Signed-off-by: Valentin Raevsky <valentin@compulab.co.il>
[christopher.spinrath@rwth-aachen.de: enhanced commit message, ported
  to upstream and some cleanup]
Signed-off-by: Christopher Spinrath <christopher.spinrath@rwth-aachen.de>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Leave pca953x P06,P07 pins on b850v3 platform and P06 pin on
b450v3/b650v3 unconfigured in the kernel space since they could be
configured as DP1_RST and DP2_RST by the applications for the DP FW
update support.

Signed-off-by: Ken Lin <ken.lin@advantech.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

The switch to the new DSA binding used "marvell,mv88e6095" for the
compatible property which doesn't exist, use "marvell,mv88e6085"
instead.

Fixes: 455b82f0 ("ARM: dts: armada-385-linksys: Utilize new DSA binding")
Signed-off-by: Ralph Sennhauser <ralph.sennhauser@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>

The compatible should be 98dx4251 not 98dx4521.

Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>

This patch adds DT node for STMicroelectronics
DELTA V4L2 video decoder

Signed-off-by: Hugues Fruchet <hugues.fruchet@st.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>

Since everybody copied my own mistake from the DT binding example,
let's address all the offenders in one swift go.

Most of them got the CPU interface size wrong (4kB, while it should
be 8kB), except for both keystone platforms which got the control
interface wrong (4kB instead of 8kB).

In a few cases where I knew for sure what implementation was used,
I've added the "arm,gic-400" compatible string. I'm 99% sure that
this is what everyone is using, but short of having the TRM for
all the other SoCs, I've left them alone.

Acked-by: Shawn Guo <shawnguo@kernel.org>
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Santosh Shilimkar <ssantosh@kernel.org>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Matthias Brugger <matthias.bgg@gmail.com>
Acked-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>

Hardware flow-control capability must be specified at a platform
level in order to inform the ASC driver that the platform is capable
(i.e. are the lines wired up, etc).  STiH4{07,10} devices are indeed
capable, so let's provide the property.

Acked-by: Peter Griffin <peter.griffin@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Having just defined some new Pinctrl groups for when HW flow-control
is {en,dis}abled, let's reference them for use within the driver.

Acked-by: Peter Griffin <peter.griffin@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Each serial port which supports HW flow-control should have 2 Pinctrl
groups.  One for when HW flow-control is in progress, where the IP
will take over controlling the lines and another group which enables
the lines to be toggled using GPIO mechanisms.

Acked-by: Peter Griffin <peter.griffin@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

When hardware flow-control is disabled, manual toggling of the UART's
reset line (RTS) using userland applications (e.g. stty) is not
possible, since the ASC IP does not provide this functionality in the
same was as some other IPs do.  Thus, we have to do this manually.
This patch configures the UART RTS line as a GPIO for manipulation
within the UART driver when HW flow-control is not enabled.

Acked-by: Peter Griffin <peter.griffin@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Enable the audio codec and the audio dai for the sun8i A33 sinlinx board.

Signed-off-by: Mylène Josserand <mylene.josserand@free-electrons.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

Enable the audio codec and the audio dai for the sun8i R16 Parrot board.

Signed-off-by: Mylène Josserand <mylene.josserand@free-electrons.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

Add the audio codec, dai and a simple card to be able to use the
audio stream of the builtin codec on sun8i SoC.

This commit adds also an audio-routing for the sound card node to link
the analog DAPM widgets (Right/Left DAC) and the digital one's as they
are created in different drivers.

Signed-off-by: Mylène Josserand <mylene.josserand@free-electrons.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

Add the device tree entries needed to support the EMAC AXI
bus settings on the Arria10 SoCFPGA chip.

Signed-off-by: Thor Thayer <thor.thayer@linux.intel.com>
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>

chiliBoard has a battery connector, so support charging battery
through tps65217 chip.

Additionally, enabling tps65217 charger allows us to get status
of AC power.

Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

On chiliBoard power button is connected to TPS65217. It signals power
button presses by asserting interrupt output and allows to read the
state by i2c bus.

Handle TPS65217 interrupts and enable notifications of power button
presses.

Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

The rename of orion5x-lschl.dts needs to be reflected in the Makefile:

make[3]: *** No rule to make target 'arch/arm/boot/dts/orion5x-lschl.dtb', needed by '__build'.

Fixes: 6cfd3cd8 ("ARM: dts: orion5x-lschl: More consistent naming on linkstation series")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>

The A23 and A33 have an ARM Mali 400 GPU. Now that we have a binding, add
it to our DT.

Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

This patch adds I2C1 instance support for STM32x9I-Eval board.

Signed-off-by: M'boumba Cedric Madianga <cedric.madianga@gmail.com>
Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com>

This patch adds I2C1 support for STM32F429 SoC

Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: M'boumba Cedric Madianga <cedric.madianga@gmail.com>
Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com>

This patch uses clock DT binding definition instead numerical values
for stm32f429 board.

Signed-off-by: Gabriel Fernandez <gabriel.fernandez@st.com>
Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com>

Define and enable pwm1 and pwm3 for stm32f469 discovery board

Signed-off-by: Benjamin Gaignard <benjamin.gaignard@st.com>
Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com>

Add Timers and it sub-nodes into DT for stm32f429 family.

Signed-off-by: Benjamin Gaignard <benjamin.gaignard@st.com>
Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com>

This clock has been missing since some early stages of device tree
conversion. Adding the right clocks to the device tree makes USB
work again.

Cc: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

The physical pins from the SoC are in a sense belonging to the
PHY device (AB8500 USB) rather than the MUSB USB IP block.
The driver definately assumes so: before this change it
complains that it cannot control the pins it is using:

abx5x0-usb ab8500-usb.0: could not get/set default pinstate

After this patch the warning goes away.

Cc: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

This moves the enable-active-high setting from the SoC to the
board for the VMMCQ regulators. It should at least be in the
vicinity of the GPIO line it is defined for.

Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Provide human readable names for all power domains defined in Exynos SoCs.

Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>

These boards are Marvell's evaluation boards for the 98DX4251 and
98DX3336 SoCs.

[gregory.clement@free-electrons.com: fix topic and update Makefile]
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>

The Marvell 98DX3236, 98DX3336, 98DX4521 and variants are switch ASICs
with integrated CPUs. They are similar to the Armada XP SoCs but have
different I/O interfaces.

[gregory.clement@free-electrons.com: fix topic]
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>

Enable the SATA node for da850-lcdk. We omit the pinctrl property on
purpose - the muxed SATA pins are not hooked up to anything
SATA-related on the lcdk.

Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>

Add the SATA node to the da850 device tree.

Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>