There is an exit path where rx is kfree'd on put_ir_rx and then
a jump to label out_put_xx will again kfree it with another
call to put_ir_rx.  Fix this by adding a new label that avoids
this 2nd call to put_ir_rx for this specific case.

Detected with CoverityScan, CID#145119 ("Use after free")

Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>

To enable eventual removal of pr_warning

This makes pr_warn use consistent for drivers/media

Prior to this patch, there was 1 use of pr_warning and
310 uses of pr_warn in drivers/media

Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>

First version of the Virtual Media Controller.
Add a simple version of the core of the driver, the capture and
sensor nodes in the topology, generating a grey image in a hardcoded
format.

Signed-off-by: Helen Koike <helen.koike@collabora.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
[hans.verkuil@cisco.com: fix small typo in Kconfig]

Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>

The OV5647 sensor from Omnivision supports up to 2592x1944 @ 15 fps, RAW 8
and RAW 10 output formats, and MIPI CSI-2 interface.

The driver adds support for 640x480 RAW 8.

Signed-off-by: Ramiro Oliveira <roliveir@synopsys.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Vladimir Zapolskiy <vladimir_zapolskiy@mentor.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>

Create device tree bindings documentation.

Signed-off-by: Ramiro Oliveira <roliveir@synopsys.com>
Acked-by: Rob Herring <robh@kernel.org>
Reviewed-by: Vladimir Zapolskiy <vladimir_zapolskiy@mentor.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>

The ov5645 sensor from Omnivision supports up to 2592x1944
and CSI2 interface.

The driver adds support for the following modes:
- 1280x960
- 1920x1080
- 2592x1944

Output format is packed 8bit UYVY.

Signed-off-by: Todor Tomov <todor.tomov@linaro.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>

Add the document for ov5645 device tree binding.

Signed-off-by: Todor Tomov <todor.tomov@linaro.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>

The two histogram controls will modify the layout of the
metadata, so this flag should be set.

Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>

Explain when the V4L2_CTRL_FLAG_MODIFY_LAYOUT and
V4L2_CTRL_FLAG_MODIFY_GRABBER flags should be used.

Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>

The rotate control will modify the layout by definition. Always
set this flag.

Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>

Add new flag to indicate that changing this control will change the
buffer/mediabus layout as well.

Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>

Document this new control flag.

Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>

The HGT is a Histogram Generator Two-Dimensions. It computes a weighted
frequency histograms for hue and saturation areas over a configurable
region of the image with optional subsampling.

Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>

The format is used on the R-Car VSP1 video queues that carry
2-D histogram statistics data.

Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>

The HGO is a Histogram Generator One-Dimension. It computes per-channel
histograms over a configurable region of the image with optional
subsampling.

Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>

The format is used on the R-Car VSP1 video queues that carry
1-D histogram statistics data.

Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>

The addresses are incorrect, fix them.

Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>

Histogram generators are single-pad entities that branch as leaf nodes
at any point in the pipeline. Make sure that pipeline traversal and
routing configuration support them correctly.

Support for the actual HGO and HGT operation will come later.

Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>

The histogram common code will be used to implement support for both the
HGO and HGT histogram computation engines.

Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>

The metadata buffer type is used to transfer metadata between userspace
and kernelspace through a V4L2 buffers queue. It comes with a new
metadata capture capability and format description.

Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Tested-by: Guennadi Liakhovetski <guennadi.liakhovetski@intel.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
[hans.verkuil@cisco.com: removed left-over 'experimental' note]
[hans.verkuil@cisco.com: add newline after _v4l2-meta-format label]

Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>

Some WPF instances, on Gen3 devices, can perform 90° rotation when
writing frames to memory. Implement support for this using the
V4L2_CID_ROTATE control.

Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>

V4L2 exposes parameters that influence buffers sizes through the format
ioctls (VIDIOC_G_FMT, VIDIOC_TRY_FMT, VIDIOC_S_FMT, and possibly
VIDIOC_G_SELECTION and VIDIOC_S_SELECTION). Other parameters not part of
the format structure may also influence buffer sizes or buffer layout in
general. One existing such parameter is rotation, which is implemented
by the V4L2_CID_ROTATE control and thus exposed through the V4L2 control
ioctls.

The interaction between those parameters and buffers is currently only
partially specified by the V4L2 API. In particular interactions between
controls and buffers isn't specified at all. The behaviour of the
VIDIOC_S_FMT and VIDIOC_S_SELECTION ioctls when buffers are allocated is
also not fully specified.

This patch clearly defines and documents the interactions between
formats, selections, controls and buffers.

The preparatory discussions for the documentation change considered
completely disallowing controls that change the buffer size or layout,
in favour of extending the format API with a new ioctl that would bundle
those controls with format information. The idea has been rejected, as
this would essentially be a restricted version of the upcoming request
API that wouldn't bring any additional value.

Another option we have considered was to mandate the use of the request
API to modify controls that influence buffer size or layout. This has
also been rejected on the grounds that requiring the request API to
change rotation even when streaming is stopped would significantly
complicate implementation of drivers and usage of the V4L2 API for
applications.

Applications will however be required to use the upcoming request API to
change at runtime formats or controls that influence the buffer size or
layout, because of the need to synchronize buffers with the formats and
controls. Otherwise there would be no way to interpret the content of a
buffer correctly.

Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>

Simplify ov2640_set_params and ov2640_set_fmt.

Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>

Simplify ov9740_s_fmt.

Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Reported-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>

Simplify ov9640_s_fmt and ov9640_set_fmt

Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>

Merge ov772x_s_fmt into ov772x_set_fmt.

Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>

Simplify ov5642_set_fmt().

Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Reported-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>

Simplify mt9v022_s_fmt and mt9v022_set_fmt.

Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>

Simplify mt9m001_s_fmt and mt9m001_set_fmt.

Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>

Simplify imx074_set_fmt().

Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Reported-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>

The Si2141 needs two distinct commands for powerup/reset, otherwise it
will not respond to chip revision requests. It also needs a firmware
to run properly.

Cc: Evgeny Plehov <EvgenyPlehov@ukr.net>
Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>

'Reset' loop does not look correct. I tested it very many times and
it never repeated those commands. If problem, it tries to solve,
really occurs on some situations better solution should be find out.

There is another patch which does not have such hackish looking loop.
Lets change to it.

Cc: Evgeny Plehov <EvgenyPlehov@ukr.net>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>

The XV601/709 encodings are special: they signal limited range, but use the full range
to encode a larger gamut with R', G' and B' values outside the [0-1] range.

So don't clamp to limited range for these two encodings.

Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>

The XV601/709 Y'CbCr encoding was changed to limited range, but the comment
still indicates full range.

Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>

Use setup_timer() instead of init_timer() to simplify the code.

Signed-off-by: Geliang Tang <geliangtang@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>

Use setup_timer() instead of init_timer() to simplify the code.

Signed-off-by: Geliang Tang <geliangtang@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>

Use setup_timer() instead of init_timer() to simplify the code.

Signed-off-by: Geliang Tang <geliangtang@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>

Use setup_timer() instead of init_timer() to simplify the code.

Signed-off-by: Geliang Tang <geliangtang@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>

Use setup_timer() instead of init_timer() to simplify the code.

Signed-off-by: Geliang Tang <geliangtang@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>

Use setup_timer() instead of init_timer() to simplify the code.

Signed-off-by: Geliang Tang <geliangtang@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>