The Axentia TSE-850 is a SAMA5D3-based device designed to generate
FM subcarrier signals.

Signed-off-by: Peter Rosin <peda@axentia.se>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>

The sama5d36ek CMP board is the variant of sama5d3xek board.
It is equipped with the low-power DDR2 SDRAM, PMIC ACT8865 and
some power rail. Its main purpose is used to measure the power
consumption.
The difference of the sama5d36ek CMP dts from sama5d36ek dts is
listed as below.
 1. The USB host nodes are removed, that is, the USB host is disabled.
 2. The gpio_keys node is added to wake up from the sleep.
 3. The LCD isn't supported due to the pins for LCD are conflicted
    with gpio_keys.
 4. The adc0 node support the pinctrl sleep state to fix the over
    consumption on VDDANA.

As said in errata, "When the USB host ports are used in high speed
mode (EHCI), it is not possible to suspend the ports if no device is
attached on each port. This leads to increased power consumption even
if the system is in a low power mode." That is why the the USB host
is disabled.

Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>

The sama5d2 SoC has Synchronous Serial Controller which provides
synchronous communication link with external devices.
It's generally used in audio and telecom applications such as
I2S, Short Frame Sync, Long Frame Sync.

Signed-off-by: Alex Gershgorin <alex.gershgorin@qcore.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>

Use DMA for UART3 as we have enough channels and to show how to
specify DMA use with serial nodes.

Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>

Now that DMA1 is defined, use it to distribute channel usage among the two
controllers.

Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>

The sama5d2 SoC has a second DMA controller and can be used just like DMA0.
By default both DMA controllers are configured as "Secure" in
MATRIX_SPSELR so we can use whichever we want in a "single Secure World"
configuration.
Surprisingly the DMA1 has a lower address than DMA0. To avoid confusion
place it after DMA0 node anyway.

Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>

Enable UART1 and use DMA configuration with it.

Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>

Some peripherals are "Programmable Secure" but left as "Secure" by default.
If tried to be connected to Non-Secure DMA controller, the possibility to
leak secure data is prevented so using these peripherals with DMA1 is not
possible with this default configuration (MATRIX_SPSELR registers setup by
bootloader).
Move them to DMA0 which is an "Always-Secure" DMA controller.

Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>

The new size (0x100) also matches the size given in sama5d3.dtsi

Documentation reference: section 43.6 "Universal Asynchronous
Receiver Transmitter (UART) User Interface", table 43-4 "Register
Mapping" in [1].

[1] Atmel-11121F-ATARM-SAMA5D3-Series-Datasheet_02-Feb-16

Signed-off-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>

The SoC hix5hd2 compatible string has the suffix "-gmac" and
we should not change it.
We should only add the generic compatible string "hisi-gmac-v1".

Fixes: 0855950b ("ARM: dts: hix5hd2: add gmac generic compatible and clock names")
Signed-off-by: Dongpo Li <lidongpo@hisilicon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Bug report from Debian [0] shows there's minor changed model of
Linkstation LS-GL that uses the 2nd SATA port of the SoC.
So it's necessary to enable two SATA ports, though for that specific
model only the 2nd one is used.

[0] https://bugs.debian.org/845611



Fixes: b1742ffa ("ARM: dts: orion5x: add device tree for buffalo linkstation ls-gl")
Reported-by: Ryan Tandy <ryan@nardis.ca>
Tested-by: Ryan Tandy <ryan@nardis.ca>
Signed-off-by: Roger Shimizu <rogershimizu@gmail.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>

The eLCDIF IP of the i.MX 7 SoC knows multiple clocks and lists them
separately:

Clock      Clock Root              Description
apb_clk    MAIN_AXI_CLK_ROOT       AXI clock
pix_clk    LCDIF_PIXEL_CLK_ROOT    Pixel clock
ipg_clk_s  MAIN_AXI_CLK_ROOT       Peripheral access clock

All of them are switched by a single gate, which is part of the
IMX7D_LCDIF_PIXEL_ROOT_CLK clock. Hence using that clock also for
the AXI bus clock (clock-name "axi") makes sure the gate gets
enabled when accessing registers.

There seem to be no separate AXI display clock, and the clock is
optional. Hence remove the dummy clock.

This fixes kernel freezes when starting the X-Server (which
disables/re-enables the display controller).

Fixes: e8ed73f6 ("ARM: dts: imx7d: add lcdif support")
Signed-off-by: Stefan Agner <stefan@agner.ch>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Acked-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Olof Johansson <olof@lixom.net>

In a previous commit, I made a copy/paste error in the pinmux
definitions of UART3: PG{13,14} instead of PA{13,14}. This commit takes
care of that. I have tested this commit on Orange Pi PC and Orange Pi
Plus, and it works for these boards.

Fixes: e3d11d3c ("dts: sun8i-h3: add pinmux definitions for
UART2-3")

Signed-off-by: Jorik Jonker <jorik@kippendief.biz>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Olof Johansson <olof@lixom.net>

Add gmac generic compatible and clock names.

Signed-off-by: Dongpo Li <lidongpo@hisilicon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Added basic dts support for MicroZed board.

- UART
- SDHCI
- Ethernet

Cc: Soren Brinkmann <soren.brinkmann@xilinx.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Jagan Teki <jteki@openedev.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>

The mmc controller in da850 supports high speed modes
so add cap-sd-highspeed and cap-mmc-highspeed.

Signed-off-by: Axel Haslam <ahaslam@baylibre.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>

This SoC has a separate pin controller for configuring pullup/pulldown
bias on groups of pins.

Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: David Lechner <david@lechnology.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>

Several versions of DW DMAC have multi block transfers hardware
support. Hardware support of multi block transfers is disabled
by default if we use DT to configure DMAC and software emulation
of multi block transfers used instead.
Add multi-block property, so it is possible to enable hardware
multi block transfers (if present) via DT.

Switch from per device is_nollp variable to multi_block array
to be able enable/disable multi block transfers separately per
channel.

Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>

Currently the memory controller and master priorities drivers are
enabled in da850.dtsi. For boards for which there are no settings
defined, this makes these drivers emit error messages.

Disable the nodes in da850.dtsi and only enable them for da850-lcdk -
the only board that currently needs them.

Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>

In order to avoid Linux generating a random mac address on every boot,
add an ethernet0 alias that will allow u-boot to patch the dtb with
the MAC address programmed into the EEPROM.

Signed-off-by: Fabien Parent <fparent@baylibre.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>

Add PCIe support to the ARTPEC-6 SoC. This uses the existing
pcie-artpec6 driver.
So, all that is needed is device tree entries in the DTS.

Signed-off-by: Niklas Cassel <niklas.cassel@axis.com>
Signed-off-by: Jesper Nilsson <jespern@axis.com>

Add PCIe support to the ARTPEC-6 SoC. This uses the existing
pcie-artpec6 driver.
So, all that is needed is device tree entries in the DTS.

Signed-off-by: Niklas Cassel <niklas.cassel@axis.com>
Signed-off-by: Jesper Nilsson <jespern@axis.com>

This machine is an open hardware router by cz.nic driven by a
Marvell Armada 385.

Signed-off-by: Uwe Kleine-König <uwe@kleine-koenig.org>
Signed-off-by: Tomas Hlavacek <tmshlvck@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: Jisheng Zhang <jszhang@marvell.com>

This patch fixes the following DTC warnings with W=1:

Warning (unit_address_vs_reg): Node /regulators/regulator@0 has a unit
name, but no reg property
Warning (unit_address_vs_reg): Node /regulators/regulator@1 has a unit
name, but no reg property
Warning (unit_address_vs_reg): Node /regulators/regulator@2 has a unit
name, but no reg property
Warning (unit_address_vs_reg): Node /regulators/regulator@3 has a unit
name, but no reg property
Warning (unit_address_vs_reg): Node /regulators/regulator@4 has a unit
name, but no reg property

Signed-off-by: Jisheng Zhang <jszhang@marvell.com>

Add xo entry to sdhc clock node on all qcom platforms.

Signed-off-by: Ritesh Harjani <riteshh@codeaurora.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>

Add a device node for the Product Register, which provides SoC product
and revision information.

Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Add a device node for the Product Register, which provides SoC product
and revision information.

Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Add a device node for the Product Register, which provides SoC product
and revision information.

Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Add a device node for the Product Register, which provides SoC product
and revision information.

Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Add a device node for the Product Register, which provides SoC product
and revision information.

Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Add a device node for the Product Register, which provides SoC product
and revision information.

Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Add a device node for the Product Register, which provides SoC product
and revision information.

Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Define the SK-RZG1E board dependent part of the Ether device node.
Enable DHCP and NFS root  for the kernel booting.

Based on the original (and large) patch by Dmitry Shifrin
<dmitry.shifrin@cogentembedded.com>.

Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Add the initial  device tree for the R8A7745 SoC based SK-RZG1E board.
The board has 1  debug  serial  port (SCIF2); include support for it,
so that the serial console can  work.

Based on the original (and large) patch by Dmitry Shifrin
<dmitry.shifrin@cogentembedded.com>.

Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Describe the IRQC interrupt controller in the R8A7745 device tree.

Based on the original (and large) patch by Dmitry Shifrin
<dmitry.shifrin@cogentembedded.com>.

Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Define the generic R8A7745 part of the Ether device node.

Based on the original (and large) patch by Dmitry Shifrin
<dmitry.shifrin@cogentembedded.com>.

Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Describe [H]SCIF{|A|B} ports in the R8A7745 device tree.

Based on the original (and large) patch by Dmitry Shifrin
<dmitry.shifrin@cogentembedded.com>.

Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
[simon: consistently use tabs for indentation]
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Describe SYS-DMAC0/1 in the R8A7745 device tree.

Based on the original (and large) patch by Dmitry Shifrin
<dmitry.shifrin@cogentembedded.com>.

Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

The  initial R8A7745 SoC device tree including CPU0, GIC, timer, SYSC, RST,
CPG, and the required clock descriptions.

Based on the original (and large) patch by Dmitry Shifrin
<dmitry.shifrin@cogentembedded.com>.

Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>