Sending them out on a different queue can cause a race condition where a
number of packets in the queue may be discarded by the receiver, because
the ADDBA request is sent too early.
This affects any driver with software A-MPDU setup which does not allocate
packet seqno in hardware on tx, regardless of whether iTXQ is used or not.
The only driver I've seen that explicitly deals with this issue internally
is mwl8k.

Cc: stable@vger.kernel.org
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Link: https://lore.kernel.org/r/20211202124533.80388-1-nbd@nbd.name


Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Reload the regdom when the regulatory db is reloaded.
Otherwise, the user had to change the regulatoy domain
to a different one and then reset it to the correct
one to have a new regulatory db take effect after a
reload.

Signed-off-by: Finn Behrens <fin@nyantec.com>
Link: https://lore.kernel.org/r/YaIIZfxHgqc/UTA7@gimli.kloenk.dev


[edit commit message]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

As pointed out by Stephen, add the missing docs.

Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Link: https://lore.kernel.org/r/20211129091948.1327ec82beab.Iecc5975406a3028d35c65ff8d2dec31a693888d3@changeid


Signed-off-by: Johannes Berg <johannes.berg@intel.com>

The following is from a system that went OOM due to a memory leak:

wlan0: Allocated STA 74:83:c2:64:0b:87
wlan0: Allocated STA 74:83:c2:64:0b:87
wlan0: IBSS finish 74:83:c2:64:0b:87 (---from ieee80211_ibss_add_sta)
wlan0: Adding new IBSS station 74:83:c2:64:0b:87
wlan0: moving STA 74:83:c2:64:0b:87 to state 2
wlan0: moving STA 74:83:c2:64:0b:87 to state 3
wlan0: Inserted STA 74:83:c2:64:0b:87
wlan0: IBSS finish 74:83:c2:64:0b:87 (---from ieee80211_ibss_work)
wlan0: Adding new IBSS station 74:83:c2:64:0b:87
wlan0: moving STA 74:83:c2:64:0b:87 to state 2
wlan0: moving STA 74:83:c2:64:0b:87 to state 3
.
.
wlan0: expiring inactive not authorized STA 74:83:c2:64:0b:87
wlan0: moving STA 74:83:c2:64:0b:87 to state 2
wlan0: moving STA 74:83:c2:64:0b:87 to state 1
wlan0: Removed STA 74:83:c2:64:0b:87
wlan0: Destroyed STA 74:83:c2:64:0b:87

The ieee80211_ibss_finish_sta() is called twice on the same STA from 2
different locations. On the second attempt, the allocated STA is not
destroyed creating a kernel memory leak.

This is happening because sta_info_insert_finish() does not call
sta_info_free() the second time when the STA already exists (returns
-EEXIST). Note that the caller sta_info_insert_rcu() assumes STA is
destroyed upon errors.

Same fix is applied to -ENOMEM.

Signed-off-by: Ahmed Zaki <anzaki@gmail.com>
Link: https://lore.kernel.org/r/20211002145329.3125293-1-anzaki@gmail.com


[change the error path label to use the existing code]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Mesh forwarding requires that the fwd_skb->dev is set up for TX handling,
otherwise the following warning will be generated, so set it up for the
pending frames.

[   72.835674 ] WARNING: CPU: 0 PID: 1193 at __skb_flow_dissect+0x284/0x1298
[   72.842379 ] Modules linked in: ksmbd pppoe ppp_async l2tp_ppp ...
[   72.962020 ] CPU: 0 PID: 1193 Comm: kworker/u5:1 Tainted: P S 5.4.137 #0
[   72.969938 ] Hardware name: MT7622_MT7531 RFB (DT)
[   72.974659 ] Workqueue: napi_workq napi_workfn
[   72.979025 ] pstate: 60000005 (nZCv daif -PAN -UAO)
[   72.983822 ] pc : __skb_flow_dissect+0x284/0x1298
[   72.988444 ] lr : __skb_flow_dissect+0x54/0x1298
[   72.992977 ] sp : ffffffc010c738c0
[   72.996293 ] x29: ffffffc010c738c0 x28: 0000000000000000
[   73.001615 ] x27: 000000000000ffc2 x26: ffffff800c2eb818
[   73.006937 ] x25: ffffffc010a987c8 x24: 00000000000000ce
[   73.012259 ] x23: ffffffc010c73a28 x22: ffffffc010a99c60
[   73.017581 ] x21: 000000000000ffc2 x20: ffffff80094da800
[   73.022903 ] x19: 0000000000000000 x18: 0000000000000014
[   73.028226 ] x17: 00000000084d16af x16: 00000000d1fc0bab
[   73.033548 ] x15: 00000000715f6034 x14: 000000009dbdd301
[   73.038870 ] x13: 00000000ea4dcbc3 x12: 0000000000000040
[   73.044192 ] x11: 000000000eb00ff0 x10: 0000000000000000
[   73.049513 ] x9 : 000000000eb00073 x8 : 0000000000000088
[   73.054834 ] x7 : 0000000000000000 x6 : 0000000000000001
[   73.060155 ] x5 : 0000000000000000 x4 : 0000000000000000
[   73.065476 ] x3 : ffffffc010a98000 x2 : 0000000000000000
[   73.070797 ] x1 : 0000000000000000 x0 : 0000000000000000
[   73.076120 ] Call trace:
[   73.078572 ]  __skb_flow_dissect+0x284/0x1298
[   73.082846 ]  __skb_get_hash+0x7c/0x228
[   73.086629 ]  ieee80211_txq_may_transmit+0x7fc/0x17b8 [mac80211]
[   73.092564 ]  ieee80211_tx_prepare_skb+0x20c/0x268 [mac80211]
[   73.098238 ]  ieee80211_tx_pending+0x144/0x330 [mac80211]
[   73.103560 ]  tasklet_action_common.isra.16+0xb4/0x158
[   73.108618 ]  tasklet_action+0x2c/0x38
[   73.112286 ]  __do_softirq+0x168/0x3b0
[   73.115954 ]  do_softirq.part.15+0x88/0x98
[   73.119969 ]  __local_bh_enable_ip+0xb0/0xb8
[   73.124156 ]  napi_workfn+0x58/0x90
[   73.127565 ]  process_one_work+0x20c/0x478
[   73.131579 ]  worker_thread+0x50/0x4f0
[   73.135249 ]  kthread+0x124/0x128
[   73.138484 ]  ret_from_fork+0x10/0x1c

Signed-off-by: Xing Song <xing.song@mediatek.com>
Tested-By: Frank Wunderlich <frank-w@public-files.de>
Link: https://lore.kernel.org/r/20211123033123.2684-1-xing.song@mediatek.com


Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Some drivers that do their own sequence number allocation (e.g. ath9k) rely
on being able to modify params->ssn on starting tx ampdu sessions.
This was broken by a change that modified it to use sta->tid_seq[tid] instead.

Cc: stable@vger.kernel.org
Fixes: 31d8bb4e

 ("mac80211: agg-tx: refactor sending addba")
Reported-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Link: https://lore.kernel.org/r/20211124094024.43222-1-nbd@nbd.name


Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Since retransmission clears info->control, rate control needs to be called
again, otherwise the driver might crash due to invalid rates.

Cc: stable@vger.kernel.org # 5.14+
Reported-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Reported-by: Robert W <rwbugreport@lost-in-the-void.net>
Fixes: 03c3911d

 ("mac80211: call ieee80211_tx_h_rate_ctrl() when dequeue")
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Tested-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Link: https://lore.kernel.org/r/20211122204323.9787-1-nbd@nbd.name


Signed-off-by: Johannes Berg <johannes.berg@intel.com>

For admission control, obviously all of that only works for
QoS data frames, otherwise we cannot even access the QoS
field in the header.

Syzbot reported (see below) an uninitialized value here due
to a status of a non-QoS nullfunc packet, which isn't even
long enough to contain the QoS header.

Fix this to only do anything for QoS data packets.

Reported-by:  <syzbot+614e82b88a1a4973e534@syzkaller.appspotmail.com>
Fixes: 02219b3a ("mac80211: add WMM admission control support")
Link: https://lore.kernel.org/r/20211122124737.dad29e65902a.Ieb04587afacb27c14e0de93ec1bfbefb238cc2a0@changeid


Signed-off-by: Johannes Berg <johannes.berg@intel.com>

sta is NULL for mesh point (resolved later), so sk pacing parameters
were not applied.

Signed-off-by: Maxime Bizon <mbizon@freebox.fr>
Link: https://lore.kernel.org/r/66f51659416ac35d6b11a313bd3ffe8b8a43dd55.camel@freebox.fr


Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Jakub Kicinski says:

====================
tls: splice_read fixes

As I work my way to unlocked and zero-copy TLS Rx the obvious bugs
in the splice_read implementation get harder and harder to ignore.
This is to say the fixes here are discovered by code inspection,
I'm not aware of anyone actually using splice_read.
====================

Link: https://lore.kernel.org/r/20211124232557.2039757-1-kuba@kernel.org


Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Previous patch fixes overriding callbacks incorrectly. Triggering
the crash in sendpage_locked would be more spectacular but it's
hard to get to, so take the easier path of proving this is broken
and call getname. We're currently getting IPv4 socket info on an
IPv6 socket.

Signed-off-by: Jakub Kicinski <kuba@kernel.org>

We replace proto_ops whenever TLS is configured for RX. But our
replacement also overrides sendpage_locked, which will crash
unless TX is also configured. Similarly we plug both of those
in for TLS_HW (NIC crypto offload) even tho TLS_HW has a completely
different implementation for TX.

Last but not least we always plug in something based on inet_stream_ops
even though a few of the callbacks differ for IPv6 (getname, release,
bind).

Use a callback building method similar to what we do for struct proto.

Fixes: c46234eb ("tls: RX path for ktls")
Fixes: d4ffb02d

 ("net/tls: enable sk_msg redirect to tls socket egress")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Add tests for half-received and peeked records.

Signed-off-by: Jakub Kicinski <kuba@kernel.org>

recvmsg() will put peek()ed and partially read records onto the rx_list.
splice_read() needs to consult that list otherwise it may miss data.
Align with recvmsg() and also put partially-read records onto rx_list.
tls_sw_advance_skb() is pretty pointless now and will be removed in
net-next.

Fixes: 692d7b5d

 ("tls: Fix recvmsg() to be able to peek across multiple records")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Make sure we correctly reject splicing non-data records.

Signed-off-by: Jakub Kicinski <kuba@kernel.org>

We don't support splicing control records. TLS 1.3 changes moved
the record type check into the decrypt if(). The skb may already
be decrypted and still be an alert.

Note that decrypt_skb_update() is idempotent and updates ctx->decrypted
so the if() is pointless.

Reorder the check for decryption errors with the content type check
while touching them. This part is not really a bug, because if
decryption failed in TLS 1.3 content type will be DATA, and for
TLS 1.2 it will be correct. Nevertheless its strange to touch output
before checking if the function has failed.

Fixes: fedf201e

 ("net: tls: Refactor control message handling on recv")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Test broken records.

Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Add helpers for sending and receiving special record types.

Signed-off-by: Jakub Kicinski <kuba@kernel.org>

We have the same code 3 times, about to add a fourth copy.

Signed-off-by: Jakub Kicinski <kuba@kernel.org>

The issue happened randomly in runtime.  The message "Link is Down" is
popped but soon it recovered to "Link is Up".

The "Link is Down" results from the incorrect read data for reading the
PHY register via MDIO bus.  The correct sequence for reading the data
shall be:
1. fire the command
2. wait for command done (this step was missing)
3. wait for data idle
4. read data from data register

Cc: stable@vger.kernel.org
Fixes: f160e994

 ("net: phy: Add mdio-aspeed")
Reviewed-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Dylan Hung <dylan_hung@aspeedtech.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://lore.kernel.org/r/20211125024432.15809-1-dylan_hung@aspeedtech.com


Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Oleksandr brought a bug report where netpoll causes trace
messages in the log on igb.

Danielle brought this back up as still occurring, so we'll try
again.

[22038.710800] ------------[ cut here ]------------
[22038.710801] igb_poll+0x0/0x1440 [igb] exceeded budget in poll
[22038.710802] WARNING: CPU: 12 PID: 40362 at net/core/netpoll.c:155 netpoll_poll_dev+0x18a/0x1a0

As Alex suggested, change the driver to return work_done at the
exit of napi_poll, which should be safe to do in this driver
because it is not polling multiple queues in this single napi
context (multiple queues attached to one MSI-X vector). Several
other drivers contain the same simple sequence, so I hope
this will not create new problems.

Fixes: 16eb8815

 ("igb: Refactor clean_rx_irq to reduce overhead and improve performance")
Reported-by: Oleksandr Natalenko <oleksandr@natalenko.name>
Reported-by: Danielle Ratson <danieller@nvidia.com>
Suggested-by: Alexander Duyck <alexander.duyck@gmail.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Oleksandr Natalenko <oleksandr@natalenko.name>
Tested-by: Danielle Ratson <danieller@nvidia.com>
Link: https://lore.kernel.org/r/20211123204000.1597971-1-jesse.brandeburg@intel.com


Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Karsten Graul says:

====================
net/smc: fixes 2021-11-24

Patch 1 from DaXing fixes a possible loop in smc_listen().
Patch 2 prevents a NULL pointer dereferencing while iterating
over the lower network devices.
====================

Link: https://lore.kernel.org/r/20211124123238.471429-1-kgraul@linux.ibm.com


Signed-off-by: Jakub Kicinski <kuba@kernel.org>

The kernel_listen function in smc_listen will fail when all the available
ports are occupied.  At this point smc->clcsock->sk->sk_data_ready has
been changed to smc_clcsock_data_ready.  When we call smc_listen again,
now both smc->clcsock->sk->sk_data_ready and smc->clcsk_data_ready point
to the smc_clcsock_data_ready function.

The smc_clcsock_data_ready() function calls lsmc->clcsk_data_ready which
now points to itself resulting in an infinite loop.

This patch restores smc->clcsock->sk->sk_data_ready with the old value.

Fixes: a60a2b1e

 ("net/smc: reduce active tcp_listen workers")
Signed-off-by: Guo DaXing <guodaxing@huawei.com>
Acked-by: Tony Lu <tonylu@linux.alibaba.com>
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Coverity reports a possible NULL dereferencing problem:

in smc_vlan_by_tcpsk():
6. returned_null: netdev_lower_get_next returns NULL (checked 29 out of 30 times).
7. var_assigned: Assigning: ndev = NULL return value from netdev_lower_get_next.
1623                ndev = (struct net_device *)netdev_lower_get_next(ndev, &lower);
CID 1468509 (#1 of 1): Dereference null return value (NULL_RETURNS)
8. dereference: Dereferencing a pointer that might be NULL ndev when calling is_vlan_dev.
1624                if (is_vlan_dev(ndev)) {

Remove the manual implementation and use netdev_walk_all_lower_dev() to
iterate over the lower devices. While on it remove an obsolete function
parameter comment.

Fixes: cb9d43f6

 ("net/smc: determine vlan_id of stacked net_device")
Suggested-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Marek Behún says:

====================
phylink resolve fixes

With information from me and my nagging, Russell has produced two fixes
for phylink, which add code that triggers another phylink_resolve() from
phylink_resolve(), if certain conditions are met:
  interface is being changed
or
  link is down and previous link was up
These are needed because sometimes the PCS callbacks may provide stale
values if link / speed / ...
====================

Link: https://lore.kernel.org/r/20211123154403.32051-1-kabel@kernel.org


Signed-off-by: Jakub Kicinski <kuba@kernel.org>

On mv88e6xxx 1G/2.5G PCS, the SerDes register 4.2001.2 has the following
description:
  This register bit indicates when link was lost since the last
  read. For the current link status, read this register
  back-to-back.

Thus to get current link state, we need to read the register twice.

But doing that in the link change interrupt handler would lead to
potentially ignoring link down events, which we really want to avoid.

Thus this needs to be solved in phylink's resolve, by retriggering
another resolve in the event when PCS reports link down and previous
link was up, and by re-reading PCS state if the previous link was down.

The wrong value is read when phylink requests change from sgmii to
2500base-x mode, and link won't come up. This fixes the bug.

Fixes: 9525ae83

 ("phylink: add phylink infrastructure")
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

On PHY state change the phylink_resolve() function can read stale
information from the MAC and report incorrect link speed and duplex to
the kernel message log.

Example with a Marvell 88X3310 PHY connected to a SerDes port on Marvell
88E6393X switch:
- PHY driver triggers state change due to PHY interface mode being
  changed from 10gbase-r to 2500base-x due to copper change in speed
  from 10Gbps to 2.5Gbps, but the PHY itself either hasn't yet changed
  its interface to the host, or the interrupt about loss of SerDes link
  hadn't arrived yet (there can be a delay of several milliseconds for
  this), so we still think that the 10gbase-r mode is up
- phylink_resolve()
  - phylink_mac_pcs_get_state()
    - this fills in speed=10g link=up
  - interface mode is updated to 2500base-x but speed is left at 10Gbps
  - phylink_major_config()
    - interface is changed to 2500base-x
  - phylink_link_up()
    - mv88e6xxx_mac_link_up()
      - .port_set_speed_duplex()
        - speed is set to 10Gbps
    - reports "Link is Up - 10Gbps/Full" to dmesg

Afterwards when the interrupt finally arrives for mv88e6xxx, another
resolve is forced in which we get the correct speed from
phylink_mac_pcs_get_state(), but since the interface is not being
changed anymore, we don't call phylink_major_config() but only
phylink_mac_config(), which does not set speed/duplex anymore.

To fix this, we need to force the link down and trigger another resolve
on PHY interface change event.

Fixes: 9525ae83

 ("phylink: add phylink infrastructure")
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Usage of phy_ethtool_get_link_ksettings() in the link status change
handler isn't needed, and in combination with the referenced change
it results in a deadlock. Simply remove the call and replace it with
direct access to phydev->speed. The duplex argument of
lan743x_phy_update_flowcontrol() isn't used and can be removed.

Fixes: c10a485c

 ("phy: phy_ethtool_ksettings_get: Lock the phy for consistency")
Reported-by: Alessandro B Maurici <abmaurici@gmail.com>
Tested-by: Alessandro B Maurici <abmaurici@gmail.com>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/40e27f76-0ba3-dcef-ee32-a78b9df38b0f@gmail.com


Signed-off-by: Jakub Kicinski <kuba@kernel.org>

While testing BIG TCP patch series, I was expecting that TCP_RR workloads
with 80KB requests/answers would send one 80KB TSO packet,
then being received as a single GRO packet.

It turns out this was not happening, and the root cause was that
cubic Hystart ACK train was triggering after a few (2 or 3) rounds of RPC.

Hystart was wrongly setting CWND/SSTHRESH to 30, while my RPC
needed a budget of ~20 segments.

Ideally these TCP_RR flows should not exit slow start.

Cubic Hystart should reset itself at each round, instead of assuming
every TCP flow is a bulk one.

Note that even after this patch, Hystart can still trigger, depending
on scheduling artifacts, but at a higher CWND/SSTHRESH threshold,
keeping optimal TSO packet sizes.

Tested:

ip link set dev eth0 gro_ipv6_max_size 131072 gso_ipv6_max_size 131072
nstat -n; netperf -H ... -t TCP_RR  -l 5  -- -r 80000,80000 -K cubic; nstat|egrep "Ip6InReceives|Hystart|Ip6OutRequest...

Update the B53 Ethernet switch section to contain
drivers/net/dsa/bcm_sf2*.

Reported-by: Russell King (Oracle) <linux@armlinux.org.uk>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://lore.kernel.org/r/20211123222422.3745485-1-f.fainelli@gmail.com


Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Merge tag 'ieee802154-for-net-2021-11-24' of git://git.kernel.org/pub/scm/linux/kernel/git/sschmidt/wpan

Stefan Schmidt says:

====================
pull-request: ieee802154 for net 2021-11-24

A fix from Alexander which has been brought up various times found by
automated checkers. Make sure values are in u32 range.

* tag 'ieee802154-for-net-2021-11-24' of git://git.kernel.org/pub/scm/linux/kernel/git/sschmidt/wpan:
  net: ieee802154: handle iftypes as u32
====================

Link: https://lore.kernel.org/r/20211124150934.3670248-1-stefan@datenfreihafen.org


Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Update NC-SI command handler (both standard and OEM) to take into
account of payload paddings in allocating skb (in case of payload
size is not 32-bit aligned).

The checksum field follows payload field, without taking payload
padding into account can cause checksum being truncated, leading to
dropped packets.

Fixes: fb4ee675

 ("net/ncsi: Add NCSI OEM command support")
Signed-off-by: Kumar Thangavel <thangavel.k@hcl.com>
Acked-by: Samuel Mendoza-Jonas <sam@mendozajonas.com>
Reviewed-by: Paul Menzel <pmenzel@molgen.mpg.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

This was previously added in selftests but never added
to the Makefile

Signed-off-by: James Prestwood <prestwoj@gmail.com>
Link: https://lore.kernel.org/r/20211122171806.3529401-1-prestwoj@gmail.com


Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Signed-off-by: Jamal Hadi Salim <jhs@mojatatu.com>
Acked-by: Cong Wang <cong.wang@bytedance.com>
Link: https://lore.kernel.org/r/20211122144252.25156-1-jhs@emojatatu.com


Signed-off-by: Jakub Kicinski <kuba@kernel.org>

This file has not been updated for a while.

Sync it before BIG TCP patch series.

Signed-off-by: Eric Dumazet <edumazet@google.com>
Link: https://lore.kernel.org/r/20211122184810.769159-1-eric.dumazet@gmail.com


Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Currently mvpp2_xdp_setup won't allow attaching XDP program if
  mtu > ETH_DATA_LEN (1500).

The mvpp2_change_mtu on the other hand checks whether
  MVPP2_RX_PKT_SIZE(mtu) > MVPP2_BM_LONG_PKT_SIZE.

These two checks are semantically different.

Moreover this limit can be increased to MVPP2_MAX_RX_BUF_SIZE, since in
mvpp2_rx we have
  xdp.data = data + MVPP2_MH_SIZE + MVPP2_SKB_HEADROOM;
  xdp.frame_sz = PAGE_SIZE;

Change the checks to check whether
  mtu > MVPP2_MAX_RX_BUF_SIZE

Fixes: 07dd0a7a

 ("mvpp2: add basic XDP support")
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Calling ipa_cmd_pipeline_clear() after stopping the channel
underlying the AP<-modem RX endpoint can lead to a deadlock.

This occurs in the ->runtime_suspend device power operation for the
IPA driver.  While this callback is in progress, any other requests
for power will block until the callback returns.

Stopping the AP<-modem RX channel does not prevent the modem from
sending another packet to this endpoint.  If a packet arrives for an
RX channel when the channel is stopped, an SUSPEND IPA interrupt
condition will be pending.  Handling an IPA interrupt requires
power, so ipa_isr_thread() calls pm_runtime_get_sync() first thing.

The problem occurs because a "pipeline clear" command will not
complete while such a SUSPEND interrupt condition exists.  So the
SUSPEND IPA interrupt handler won't proceed until it gets power;
that won't happen until the ->runtime_suspend callback (and its
"pipeline clear" command) completes; and that can't happen while
the SUSPEND interrupt condition exists.

It turns out that in this case there is no need to use the "pipeline
clear" command.  There are scenarios in which clearing the pipeline
is required while suspending, but those are not (yet) supported
upstream.  So a simple fix, avoiding the potential deadlock, is to
stop calling ipa_cmd_pipeline_clear() in ipa_endpoint_suspend().
This removes the only user of ipa_cmd_pipeline_clear(), so get rid
of that function.  It can be restored again whenever it's needed.

This is basically a manual revert along with an explanation for
commit 6cb63ea6 ("net: ipa: introduce ipa_cmd_tag_process()").

Fixes: 6cb63ea6

 ("net: ipa: introduce ipa_cmd_tag_process()")
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

The smsc95xx driver is dropping phy speed settings and causing a stack
trace at device unbind:

[  536.379147] smsc95xx 2-1:1.0 eth1: unregister 'smsc95xx' usb-ci_hdrc.2-1, smsc95xx USB 2.0 Ethernet
[  536.425029] ------------[ cut here ]------------
[  536.429650] WARNING: CPU: 0 PID: 439 at fs/kernfs/dir.c:1535 kernfs_remove_by_name_ns+0xb8/0xc0
[  536.438416] kernfs: can not remove 'attached_dev', no directory
[  536.444363] Modules linked in: xts dm_crypt dm_mod atmel_mxt_ts smsc95xx usbnet
[  536.451748] CPU: 0 PID: 439 Comm: sh Tainted: G        W         5.15.0 #1
[  536.458636] Hardware name: Freescale i.MX53 (Device Tree Support)
[  536.464735] Backtrace: 
[  536.467190] [<80b1c904>] (dump_backtrace) from [<80b1cb48>] (show_stack+0x20/0x24)
[  536.474787]  r7:000005ff r6:8035b294 r5:600f0013 r4:80d8af78
[  536.480449] [<80b1cb28>] (show_stack) from [<80b1f764>] (dump_stack_lvl+0x48/0x54)
[  536.488035] [<80b1f71c>] (dump_stack_lvl) from [<80b1f788>] (dump_stack+0x18/0x1c)
[  536.495620]  r5:00000009 r4:80d9b820
[  536.499198] [<80b1f770>] (dump_stack) from [<80124fac>] (__warn+0xfc/0x114)
[  536.506187] [<80124eb0>] (__warn) from [<80b1d21c>] (warn_slowpath_fmt+0xa8/0xdc)
[  536.513688]  r7:000005ff r6:80d9b820 r5:80d9b8e0 r4:83744000
[  536.519349] [<80b1d178>] (warn_slowpath_fmt) from [<8035b294>] (kernfs_remove_by_name_ns+0xb8/0xc0)
[  536.528416]  r9:00000001 r8:00000000 r7:824926dc r6:00000000 r5:80df6c2c r4:00000000
[  536.536162] [<8035b1dc>] (kernfs_remove_by_name_ns) from [<80b1f56c>] (sysfs_remove_link+0x4c/0x50)
[  536.545225]  r6:7f00f02c r5:80df6c2c r4:83306400
[  536.549845] [<80b1f520>] (sysfs_remove_link) from [<806f9c8c>] (phy_detach+0xfc/0x11c)
[  536.557780]  r5:82492000 r4:83306400
[  536.561359] [<806f9b90>] (phy_detach) from [<806f9cf8>] (phy_disconnect+0x4c/0x58)
[  536.568943]  r7:824926dc r6:7f00f02c r5:82492580 r4:83306400
[  536.574604] [<806f9cac>] (phy_disconnect) from [<7f00a310>] (smsc95xx_disconnect_phy+0x30/0x38 [smsc95xx])
[  536.584290]  r5:82492580 r4:82492580
[  536.587868] [<7f00a2e0>] (smsc95xx_disconnect_phy [smsc95xx]) from [<7f001570>] (usbnet_stop+0x70/0x1a0 [usbnet])
[  536.598161]  r5:82492580 r4:82492000
[  536.601740] [<7f001500>] (usbnet_stop [usbnet]) from [<808baa70>] (__dev_close_many+0xb4/0x12c)
[  536.610466]  r8:83744000 r7:00000000 r6:83744000 r5:83745b74 r4:82492000
[  536.617170] [<808ba9bc>] (__dev_close_many) from [<808bab78>] (dev_close_many+0x90/0x120)
[  536.625365]  r7:00000001 r6:83745b74 r5:83745b8c r4:82492000
[  536.631026] [<808baae8>] (dev_close_many) from [<808bf408>] (unregister_netdevice_many+0x15c/0x704)
[  536.640094]  r9:00000001 r8:81130b98 r7:83745b74 r6:83745bc4 r5:83745b8c r4:82492000
[  536.647840] [<808bf2ac>] (unregister_netdevice_many) from [<808bfa50>] (unregister_netdevice_queue+0xa0/0xe8)
[  536.657775]  r10:8112bcc0 r9:83306c00 r8:83306c80 r7:8291e420 r6:83744000 r5:00000000
[  536.665608]  r4:82492000
[  536.668143] [<808bf9b0>] (unregister_netdevice_queue) from [<808bfac0>] (unregister_netdev+0x28/0x30)
[  536.677381]  r6:7f01003c r5:82492000 r4:82492000
[  536.682000] [<808bfa98>] (unregister_netdev) from [<7f000b40>] (usbnet_disconnect+0x64/0xdc [usbnet])
[  536.691241]  r5:82492000 r4:82492580
[  536.694819] [<7f000adc>] (usbnet_disconnect [usbnet]) from [<8076b958>] (usb_unbind_interface+0x80/0x248)
[  536.704406]  r5:7f01003c r4:83306c80
[  536.707984] [<8076b8d8>] (usb_unbind_interface) from [<8061765c>] (device_release_driver_internal+0x1c4/0x1cc)
[  536.718005]  r10:8112bcc0 r9:80dff1dc r8:83306c80 r7:83744000 r6:7f01003c r5:00000000
[  536.725838]  r4:8291e420
[  536.728373] [<80617498>] (device_release_driver_internal) from [<80617684>] (device_release_driver+0x20/0x24)
[  536.738302]  r7:83744000 r6:810d4f4c r5:8291e420 r4:8176ae30
[  536.743963] [<80617664>] (device_release_driver) from [<806156cc>] (bus_remove_device+0xf0/0x148)
[  536.752858] [<806155dc>] (bus_remove_device) from [<80610018>] (device_del+0x198/0x41c)
[  536.760880]  r7:83744000 r6:8116e2e4 r5:8291e464 r4:8291e420
[  536.766542] [<8060fe80>] (device_del) from [<80768fe8>] (usb_disable_device+0xcc/0x1e0)
[  536.774576]  r10:8112bcc0 r9:80dff1dc r8:00000001 r7:8112bc48 r6:8291e400 r5:00000001
[  536.782410]  r4:83306c00
[  536.784945] [<80768f1c>] (usb_disable_device) from [<80769c30>] (usb_set_configuration+0x514/0x8dc)
[  536.794011]  r10:00000000 r9:00000000 r8:832c3600 r7:00000004 r6:810d5688 r5:00000000
[  536.801844]  r4:83306c00
[  536.804379] [<8076971c>] (usb_set_configuration) from [<80775fac>] (usb_generic_driver_disconnect+0x34/0x38)
[  536.814236]  r10:832c3610 r9:83745ef8 r8:832c3600 r7:00000004 r6:810d5688 r5:83306c00
[  536.822069]  r4:83306c00
[  536.824605] [<80775f78>] (usb_generic_driver_disconnect) from [<8076b850>] (usb_unbind_device+0x30/0x70)
[  536.834100]  r5:83306c00 r4:810d5688
[  536.837678] [<8076b820>] (usb_unbind_device) from [<8061765c>] (device_release_driver_internal+0x1c4/0x1cc)
[  536.847432]  r5:822fb480 r4:83306c80
[  536.851009] [<80617498>] (device_release_driver_internal) from [<806176a8>] (device_driver_detach+0x20/0x24)
[  536.860853]  r7:00000004 r6:810d4f4c r5:810d5688 r4:83306c80
[  536.866515] [<80617688>] (device_driver_detach) from [<80614d98>] (unbind_store+0x70/0xe4)
[  536.874793] [<80614d28>] (unbind_store) from [<80614118>] (drv_attr_store+0x30/0x3c)
[  536.882554]  r7:00000000 r6:00000000 r5:83739200 r4:80614d28
[  536.888217] [<806140e8>] (drv_attr_store) from [<8035cb68>] (sysfs_kf_write+0x48/0x54)
[  536.896154]  r5:83739200 r4:806140e8
[  536.899732] [<8035cb20>] (sysfs_kf_write) from [<8035be84>] (kernfs_fop_write_iter+0x11c/0x1d4)
[  536.908446]  r5:83739200 r4:00000004
[  536.912024] [<8035bd68>] (kernfs_fop_write_iter) from [<802b87fc>] (vfs_write+0x258/0x3e4)
[  536.920317]  r10:00000000 r9:83745f58 r8:83744000 r7:00000000 r6:00000004 r5:00000000
[  536.928151]  r4:82adacc0
[  536.930687] [<802b85a4>] (vfs_write) from [<802b8b0c>] (ksys_write+0x74/0xf4)
[  536.937842]  r10:00000004 r9:007767a0 r8:83744000 r7:00000000 r6:00000000 r5:82adacc0
[  536.945676]  r4:82adacc0
[  536.948213] [<802b8a98>] (ksys_write) from [<802b8ba4>] (sys_write+0x18/0x1c)
[  536.955367]  r10:00000004 r9:83744000 r8:80100244 r7:00000004 r6:76f47b58 r5:76fc0350
[  536.963200]  r4:00000004
[  536.965735] [<802b8b8c>] (sys_write) from [<80100060>] (ret_fast_syscall+0x0/0x48)
[  536.973320] Exception stack(0x83745fa8 to 0x83745ff0)
[  536.978383] 5fa0:                   00000004 76fc0350 00000001 007767a0 00000004 00000000
[  536.986569] 5fc0: 00000004 76fc0350 76f47b58 00000004 76f47c7c 76f48114 00000000 7e87991c
[  536.994753] 5fe0: 00000498 7e879908 76e6dce8 76eca2e8
[  536.999922] ---[ end trace 9b835d809816b435 ]---

The driver should not be connecting and disconnecting the PHY when the
device is opened and closed, it should be stopping and starting the PHY. The
phy should be connected as part of binding and disconnected during
unbinding.

As this results in the PHY not being reset during open, link speed, etc.
settings set prior to the link coming up are now not being lost.

It is necessary for phy_stop() to only be called when the phydev still
exists (resolving the above stack trace). When unbinding, ".unbind" will be
called prior to ".stop", with phy_disconnect() already having called
phy_stop() before the phydev becomes inaccessible.

Signed-off-by: Martyn Welch <martyn.welch@collabora.com>
Cc: Steve Glendinning <steve.glendinning@shawell.net>
Cc: UNGLinuxDriver@microchip.com
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: stable@kernel.org # v5.15
Signed-off-by: David S. Miller <davem@davemloft.net>

During the process of driver probing, probe function should return < 0
for failure, otherwise kernel will treat value == 0 as success.

Therefore, we should set err to -EINVAL when
adapter->registered_device_map is NULL. Otherwise kernel will assume
that driver has been successfully probed and will cause unexpected
errors.

Signed-off-by: Zheyu Ma <zheyuma97@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The original changes brakes MAC address assignment on older chip
versions (see bug report [0]), and it brakes random MAC assignment.

is_valid_ether_addr() requires that its argument is word-aligned.
Add the missing alignment to array mac_addr.

[0] https://bugzilla.kernel.org/show_bug.cgi?id=215087

Fixes: 1c5d09d5

 ("ethernet: r8169: use eth_hw_addr_set()")
Reported-by: Richard Herbert <rherbert@sympatico.ca>
Tested-by: Richard Herbert <rherbert@sympatico.ca>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Acked-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>