Some firmware when operation don't may have broken versions leading to
error like the following:

[    6.176482] Bluetooth: hci0: Firmware revision 0.0 build 121 week 7 2021
[    6.177906] bluetooth hci0: Direct firmware load for intel/ibt-20-0-0.sfi failed with error -2
[    6.177910] Bluetooth: hci0: Failed to load Intel firmware file intel/ibt-20-0-0.sfi (-2)

Since we load the firmware file just to check if its version had changed
comparing to the one already loaded we can just skip since the firmware
is already operation.

Fixes: ac056546

 ("Bluetooth: btintel: Check firmware version before
download")
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

It turned out that the VIRTIO_ID_* are not assigned in the virtio_ids.h
file in the upstream kernel. Picking the next free one was wrong and
there is a process that has been followed now.

See https://github.com/oasis-tcs/virtio-spec/issues/108 for details.

Fixes: afd2daa2

 ("Bluetooth: Add support for virtio transport driver")
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

The hci_sock_dev_event() function will cleanup the hdev object for
sockets even if this object may still be in used within the
hci_sock_bound_ioctl() function, result in UAF vulnerability.

This patch replace the BH context lock to serialize these affairs
and prevent the race condition.

Signed-off-by: Lin Ma <linma@zju.edu.cn>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

In the cleanup routine for failed initialization of HCI device,
the flush_work(&hdev->rx_work) need to be finished before the
flush_work(&hdev->cmd_work). Otherwise, the hci_rx_work() can
possibly invoke new cmd_work and cause a bug, like double free,
in late processings.

This was assigned CVE-2021-3564.

This patch reorder the flush_work() to fix this bug.

Cc: Marcel Holtmann <marcel@holtmann.org>
Cc: Johan Hedberg <johan.hedberg@gmail.com>
Cc: Luiz Augusto von Dentz <luiz.dentz@gmail.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: linux-bluetooth@vger.kernel.org
Cc: netdev@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Lin Ma <linma@zju.edu.cn>
Signed-off-by: Hao Xiong <mart1n@zju.edu.cn>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

Document the phydev::dev_flags bit allocation to allow bits 15:0 to
define PHY driver specific behavior, bits 23:16 to be reserved for now,
and bits 31:24 to hold generic PHY driver flags.

Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://lore.kernel.org/r/20210526184617.3105012-1-f.fainelli@gmail.com


Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Daniel Borkmann says:

====================
pull-request: bpf 2021-05-26

The following pull-request contains BPF updates for your *net* tree.

We've added 14 non-merge commits during the last 14 day(s) which contain
a total of 17 files changed, 513 insertions(+), 231 deletions(-).

The main changes are:

1) Fix bpf_skb_change_head() helper to reset mac_len, from Jussi Maki.

2) Fix masking direction swap upon off-reg sign change, from Daniel Borkmann.

3) Fix BPF offloads in verifier by reordering driver callback, from Yinjun Zhang.

4) BPF selftest for ringbuf mmap ro/rw restrictions, from Andrii Nakryiko.

5) Follow-up fixes to nested bprintf per-cpu buffers, from Florent Revest.

6) Fix bpftool sock_release attach point help info, from Liu Jian.
====================

Signed-off-by: David S. Miller <davem@davemloft.net>

Mat Martineau says:

====================
MPTCP fixes

Here are a few fixes for the -net tree.

Patch 1 fixes an attempt to access a tcp-specific field that does not
exist in mptcp sockets.

Patches 2 and 3 remove warning/error log output that could be flooded.

Patch 4 performs more validation on address advertisement echo packets
to improve RFC 8684 compliance.
====================

Signed-off-by: David S. Miller <davem@davemloft.net>

when Linux receives an echo-ed ADD_ADDR, it checks the IP address against
the list of "announced" addresses. In case of a positive match, the timer
that handles retransmissions is stopped regardless of the 'Address Id' in
the received packet: this behaviour does not comply with RFC8684 3.4.1.

Fix it by validating the 'Address Id' in received echo-ed ADD_ADDRs.
Tested using packetdrill, with the following captured output:

 unpatched kernel:

 Out <...> Flags [.], ack 1, win 256, options [mptcp add-addr v1 id 1 198.51.100.2 hmac 0xfd2e62517888fe29,mptcp dss ack 3007449509], length 0
 In  <...> Flags [.], ack 1, win 257, options [mptcp add-addr v1-echo id 1 1.2.3.4,mptcp dss ack 3013740213], length 0
 Out <...> Flags [.], ack 1, win 256, options [mptcp add-addr v1 id 1 198.51.100.2 hmac 0xfd2e62517888fe29,mptcp dss ack 3007449509], length 0
 In  <...> Flags [.], ack 1, win 257, options [mptcp add-addr v1-echo id 90 198.51.100.2,mptcp dss ack 3013740213], length 0
        ^^^ retransmission is stopped here, but 'Address Id' is 90

 patched kernel:

 Out <...> Flags [.], ack 1, win 256, options [mptcp add-addr v1 id 1 198.51.100.2 hmac 0x1cf372d59e05f4b8,mptcp dss ack 3007449509], length 0
 In  <...> Flags [.], ack 1, win 257, options [mptcp add-addr v1-echo id 1 1.2.3.4,mptcp dss ack 1672384568], length 0
 Out <...> Flags [.], ack 1, win 256, options [mptcp add-addr v1 id 1 198.51.100.2 hmac 0x1cf372d59e05f4b8,mptcp dss ack 3007449509], length 0
 In  <...> Flags [.], ack 1, win 257, options [mptcp add-addr v1-echo id 90 198.51.100.2,mptcp dss ack 1672384568], length 0
 Out <...> Flags [.], ack 1, win 256, options [mptcp add-addr v1 id 1 198.51.100.2 hmac 0x1cf372d59e05f4b8,mptcp dss ack 3007449509], length 0
 In  <...> Flags [.], ack 1, win 257, options [mptcp add-addr v1-echo id 1 198.51.100.2,mptcp dss ack 1672384568], length 0
        ^^^ retransmission is stopped here, only when both 'Address Id' and 'IP Address' match

Fixes: 00cfd77b

 ("mptcp: retransmit ADD_ADDR when timeout")
Signed-off-by: Davide Caratti <dcaratti@redhat.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Another left-over. Avoid flooding dmesg with useless text,
we already have a MIB for that event.

Fixes: 648ef4b8

 ("mptcp: Implement MPTCP receive path")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This is a left-over of early day. A malicious peer can flood
the kernel logs with useless messages, just drop it.

Fixes: f296234c

 ("mptcp: Add handling of incoming MP_JOIN requests")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

We can't use tcp_set_congestion_control() on an mptcp socket, as
such function can end-up accessing a tcp-specific field -
prior_ssthresh - causing an OOB access.

To allow propagating the correct ca algo on subflow, cache the ca
name at initialization time.

Additionally avoid overriding the user-selected CA (if any) at
clone time.

Closes: https://github.com/multipath-tcp/mptcp_net-next/issues/182
Fixes: aa1fbd94

 ("mptcp: sockopt: add TCP_CONGESTION and TCP_INFO")
Acked-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Some of Netronome's activities and people have moved over to Corigine,
including NFP driver maintenance and myself.

Signed-off-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Louis Peens <louis.peens@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

If Link Partner sends frames larger than RX buffer size, MAC mark it
as oversize but still would pass it to the Packet Processor.
In this scenario, Packet Processor scatter frame between multiple buffers,
but only a single buffer would be returned to the Buffer Manager pool and
it would not refill the poll.

Patch add handling of oversize error with buffer header handling, so all
buffers would be returned to the Buffer Manager pool.

Fixes: 3f518509

 ("ethernet: Add new driver for Marvell Armada 375 network unit")
Reported-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Stefan Chulski <stefanc@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Eliminate the follow smatch warning:

drivers/net/ethernet/broadcom/bnx2x/bnx2x_sriov.c:1227
bnx2x_iov_init_one() warn: missing error code 'err'.

Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Signed-off-by: Jiapeng Chong <jiapeng.chong@linux.alibaba.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Function skb_ext_add() doesn't initialize created skb extension with any
value and leaves it up to the user. However, since extension of type
TC_SKB_EXT originally contained only single value tc_skb_ext->chain its
users used to just assign the chain value without setting whole extension
memory to zero first. This assumption changed when TC_SKB_EXT extension was
extended with additional fields but not all users were updated to
initialize the new fields which leads to use of uninitialized memory
afterwards. UBSAN log:

[  778.299821] UBSAN: invalid-load in net/openvswitch/flow.c:899:28
[  778.301495] load of value 107 is not a valid value for type '_Bool'
[  778.303215] CPU: 0 PID: 0 Comm: swapper/0 Not tainted 5.12.0-rc7+ #2
[  778.304933] Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS rel-1.13.0-0-gf21b5a4aeb02-prebuilt.qemu.org 04/01/2014
[  778.307901] Call Trace:
[  778.308680]  <IRQ>
[  778.309358]  dump_stack+0xbb/0x107
[  778.310307]  ubsan_epilogue+0x5/0x40
[  778.311167]  __ubsan_handle_load_invalid_value.cold+0x43/0x48
[  778.312454]  ? memset+0x20/0x40
[  778.313230]  ovs_flow_key_extract.cold+0xf/0x14 [openvswitch]
[  778.314532]  ovs_vport_receive+0x19e/0x2e0 [openvswitch]
[  778.315749]  ? ovs_vport_find_upcall_portid+0x330/0x330 [openvswitch]
[  778.317188]  ? create_prof_cpu_mask+0x20/0x20
[  778.318220]  ? arch_stack_walk+0x82/0xf0
[  778.319153]  ? secondary_startup_64_no_verify+0xb0/0xbb
[  778.320399]  ? stack_trace_save+0x91/0xc0
[  778.321362]  ? stack_trace_consume_entry+0x160/0x160
[  778.322517]  ? lock_release+0x52e/0x760
[  778.323444]  netdev_frame_hook+0x323/0x610 [openvswitch]
[  778.324668]  ? ovs_netdev_get_vport+0xe0/0xe0 [openvswitch]
[  778.325950]  __netif_receive_skb_core+0x771/0x2db0
[  778.327067]  ? lock_downgrade+0x6e0/0x6f0
[  778.328021]  ? lock_acquire+0x565/0x720
[  778.328940]  ? generic_xdp_tx+0x4f0/0x4f0
[  778.329902]  ? inet_gro_receive+0x2a7/0x10a0
[  778.330914]  ? lock_downgrade+0x6f0/0x6f0
[  778.331867]  ? udp4_gro_receive+0x4c4/0x13e0
[  778.332876]  ? lock_release+0x52e/0x760
[  778.333808]  ? dev_gro_receive+0xcc8/0x2380
[  778.334810]  ? lock_downgrade+0x6f0/0x6f0
[  778.335769]  __netif_receive_skb_list_core+0x295/0x820
[  778.336955]  ? process_backlog+0x780/0x780
[  778.337941]  ? mlx5e_rep_tc_netdevice_event_unregister+0x20/0x20 [mlx5_core]
[  778.339613]  ? seqcount_lockdep_reader_access.constprop.0+0xa7/0xc0
[  778.341033]  ? kvm_clock_get_cycles+0x14/0x20
[  778.342072]  netif_receive_skb_list_internal+0x5f5/0xcb0
[  778.343288]  ? __kasan_kmalloc+0x7a/0x90
[  778.344234]  ? mlx5e_handle_rx_cqe_mpwrq+0x9e0/0x9e0 [mlx5_core]
[  778.345676]  ? mlx5e_xmit_xdp_frame_mpwqe+0x14d0/0x14d0 [mlx5_core]
[  778.347140]  ? __netif_receive_skb_list_core+0x820/0x820
[  778.348351]  ? mlx5e_post_rx_mpwqes+0xa6/0x25d0 [mlx5_core]
[  778.349688]  ? napi_gro_flush+0x26c/0x3c0
[  778.350641]  napi_complete_done+0x188/0x6b0
[  778.351627]  mlx5e_napi_poll+0x373/0x1b80 [mlx5_core]
[  778.352853]  __napi_poll+0x9f/0x510
[  778.353704]  ? mlx5_flow_namespace_set_mode+0x260/0x260 [mlx5_core]
[  778.355158]  net_rx_action+0x34c/0xa40
[  778.356060]  ? napi_threaded_poll+0x3d0/0x3d0
[  778.357083]  ? sched_clock_cpu+0x18/0x190
[  778.358041]  ? __common_interrupt+0x8e/0x1a0
[  778.359045]  __do_softirq+0x1ce/0x984
[  778.359938]  __irq_exit_rcu+0x137/0x1d0
[  778.360865]  irq_exit_rcu+0xa/0x20
[  778.361708]  common_interrupt+0x80/0xa0
[  778.362640]  </IRQ>
[  778.363212]  asm_common_interrupt+0x1e/0x40
[  778.364204] RIP: 0010:native_safe_halt+0xe/0x10
[  778.365273] Code: 4f ff ff ff 4c 89 e7 e8 50 3f 40 fe e9 dc fe ff ff 48 89 df e8 43 3f 40 fe eb 90 cc e9 07 00 00 00 0f 00 2d 74 05 62 00 fb f4 <c3> 90 e9 07 00 00 00 0f 00 2d 64 05 62 00 f4 c3 cc cc 0f 1f 44 00
[  778.369355] RSP: 0018:ffffffff84407e48 EFLAGS: 00000246
[  778.370570] RAX: ffff88842de46a80 RBX: ffffffff84425840 RCX: ffffffff83418468
[  778.372143] RDX: 000000000026f1da RSI: 0000000000000004 RDI: ffffffff8343af5e
[  778.373722] RBP: fffffbfff0884b08 R08: 0000000000000000 R09: ffff88842de46bcb
[  778.375292] R10: ffffed1085bc8d79 R11: 0000000000000001 R12: 0000000000000000
[  778.376860] R13: ffffffff851124a0 R14: 0000000000000000 R15: dffffc0000000000
[  778.378491]  ? rcu_eqs_enter.constprop.0+0xb8/0xe0
[  778.379606]  ? default_idle_call+0x5e/0xe0
[  778.380578]  default_idle+0xa/0x10
[  778.381406]  default_idle_call+0x96/0xe0
[  778.382350]  do_idle+0x3d4/0x550
[  778.383153]  ? arch_cpu_idle_exit+0x40/0x40
[  778.384143]  cpu_startup_entry+0x19/0x20
[  778.385078]  start_kernel+0x3c7/0x3e5
[  778.385978]  secondary_startup_64_no_verify+0xb0/0xbb

Fix the issue by providing new function tc_skb_ext_alloc() that allocates
tc skb extension and initializes its memory to 0 before returning it to the
caller. Change all existing users to use new API instead of calling
skb_ext_add() directly.

Fixes: 038ebb1a ("net/sched: act_ct: fix miss set mru for ovs after defrag in act_ct")
Fixes: d29334c1

 ("net/sched: act_api: fix miss set post_ct for ovs after do conntrack in act_ct")
Signed-off-by: Vlad Buslov <vladbu@nvidia.com>
Acked-by: Cong Wang <cong.wang@bytedance.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Fix function name in hns_ethtool.c kernel-doc comment
to remove these warnings found by clang_w1.

drivers/net/ethernet/hisilicon/hns/hns_ethtool.c:202: warning: expecting
prototype for hns_nic_set_link_settings(). Prototype was for
hns_nic_set_link_ksettings() instead.
drivers/net/ethernet/hisilicon/hns/hns_ethtool.c:837: warning: expecting
prototype for get_ethtool_stats(). Prototype was for
hns_get_ethtool_stats() instead.
drivers/net/ethernet/hisilicon/hns/hns_ethtool.c:894: warning:
expecting prototype for get_strings(). Prototype was for
hns_get_strings() instead.

Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Fixes: 'commit 262b38cd

 ("net: ethernet: hisilicon: hns: use phydev
from struct net_device")'
Signed-off-by: Yang Li <yang.lee@linux.alibaba.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

proc_dointvec() cannot do min and max check for setting a value
when extra1/extra2 is set, so change it to proc_dointvec_minmax()
for sysctl encap_port.

Fixes: e8a3001c

 ("sctp: add encap_port for netns sock asoc and transport")
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch is to add the missing setting back for asoc encap_port.

Fixes: 8dba2960

 ("sctp: add SCTP_REMOTE_UDP_ENCAPS_PORT sockopt")
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Given we don't need to simulate the speculative domain for registers with
immediates anymore since the verifier uses direct imm-based rewrites instead
of having to mask, we can also lift a few cases that were previously rejected.

Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>

In 801c6058

 ("bpf: Fix leakage of uninitialized bpf stack under
speculation") we replaced masking logic with direct loads of immediates
if the register is a known constant. Given in this case we do not apply
any masking, there is also no reason for the operation to be truncated
under the speculative domain.

Therefore, there is also zero reason for the verifier to branch-off and
simulate this case, it only needs to do it for unknown but bounded scalars.
As a side-effect, this also enables few test cases that were previously
rejected due to simulation under zero truncation.

Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Reviewed-by: Piotr Krysiuk <piotras@gmail.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>

Masking direction as indicated via mask_to_left is considered to be
calculated once and then used to derive pointer limits. Thus, this
needs to be placed into bpf_sanitize_info instead so we can pass it
to sanitize_ptr_alu() call after the pointer move. Piotr noticed a
corner case where the off reg causes masking direction change which
then results in an incorrect final aux->alu_limit.

Fixes: 7fedb63a

 ("bpf: Tighten speculative pointer arithmetic mask")
Reported-by: Piotr Krysiuk <piotras@gmail.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Reviewed-by: Piotr Krysiuk <piotras@gmail.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>

Add a container structure struct bpf_sanitize_info which holds
the current aux info, and update call-sites to sanitize_ptr_alu()
to pass it in. This is needed for passing in additional state
later on.

Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Reviewed-by: Piotr Krysiuk <piotras@gmail.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>

Similarly as 6bdacdb4 ("bpf: Fix BPF_JIT kconfig symbol dependency") we
need to detangle the hard BPF_LSM dependency on NET. This was previously
implicit by its dependency on BPF_JIT which itself was dependent on NET (but
without any actual/real hard dependency code-wise). Given the latter was
lifted, so should be the former as BPF_LSMs could well exist on net-less
systems. This therefore also fixes a randconfig build error recently reported
by Randy:

  ld: kernel/bpf/bpf_lsm.o: in function `bpf_lsm_func_proto':
  bpf_lsm.c:(.text+0x1a0): undefined reference to `bpf_sk_storage_get_proto'
  ld: bpf_lsm.c:(.text+0x1b8): undefined reference to `bpf_sk_storage_delete_proto'
  [...]

Fixes: b24abcff

 ("bpf, kconfig: Add consolidated menu entry for bpf with core options")
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Tested-by: Randy Dunlap <rdunlap@infradead.org>

Add a test case for using bpf_skb_change_head() in combination with
bpf_redirect_peer() to redirect a packet from a L3 device to veth and back.

The test uses a BPF program that adds L2 headers to the packet coming
from a L3 device and then calls bpf_redirect_peer() to redirect the packet
to a veth device. The test fails as skb->mac_len is not set properly and
thus the ethernet headers are not properly skb_pull'd in cls_bpf_classify(),
causing tcp_v4_rcv() to point the TCP header into middle of the IP header.

Signed-off-by: Jussi Maki <joamaki@gmail.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Link: https://lore.kernel.org/bpf/20210525102955.2811090-1-joamaki@gmail.com

The help information was not added at the time when the function got added.
Fix this and add the missing information to its cli, documentation and bash
completion.

Fixes: db94cc0b

 ("bpftool: Add support for BPF_CGROUP_INET_SOCK_RELEASE")
Signed-off-by: Liu Jian <liujian56@huawei.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Reviewed-by: Quentin Monnet <quentin@isovalent.com>
Link: https://lore.kernel.org/bpf/20210525014139.323859-1-liujian56@huawei.com

Also enable phy errata workaround on 9567 since has the same errata as
the 9477 according to the manufacture's documentation.

Signed-off-by: George McCollister <george.mccollister@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Syzbot reported memory leak in smsc75xx_bind().
The problem was is non-freed memory in case of
errors after memory allocation.

backtrace:
  [<ffffffff84245b62>] kmalloc include/linux/slab.h:556 [inline]
  [<ffffffff84245b62>] kzalloc include/linux/slab.h:686 [inline]
  [<ffffffff84245b62>] smsc75xx_bind+0x7a/0x334 drivers/net/usb/smsc75xx.c:1460
  [<ffffffff82b5b2e6>] usbnet_probe+0x3b6/0xc30 drivers/net/usb/usbnet.c:1728

Fixes: d0cad871

 ("smsc75xx: SMSC LAN75xx USB gigabit ethernet adapter driver")
Cc: stable@kernel.vger.org
Reported-and-tested-by:  <syzbot+b558506ba8165425fee2@syzkaller.appspotmail.com>
Signed-off-by: Pavel Skripkin <paskripkin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Commit 2e9f6093 ("net: hsr: check skb can contain struct hsr_ethhdr
in fill_frame_info") added the following which resulted in -EINVAL
always being returned:
	if (skb->mac_len < sizeof(struct hsr_ethhdr))
		return -EINVAL;

mac_len was not being set correctly so this check completely broke
HSR/PRP since it was always 14, not 20.

Set mac_len correctly and modify the mac_len checks to test in the
correct places since sometimes it is legitimately 14.

Fixes: 2e9f6093

 ("net: hsr: check skb can contain struct hsr_ethhdr in fill_frame_info")
Signed-off-by: George McCollister <george.mccollister@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In cops_probe1(), there is a write to dev->base_addr after requesting an
interrupt line and registering the interrupt handler cops_interrupt().
The handler might be called in parallel to handle an interrupt.
cops_interrupt() tries to read dev->base_addr leading to a potential
data race. So write to dev->base_addr before calling request_irq().

Found by Linux Driver Verification project (linuxtesting.org).

Signed-off-by: Saubhik Mukherjee <saubhik.mukherjee@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Vladimir Oltean says:

====================
Fixes for SJA1105 DSA driver

This series contains some minor fixes in the sja1105 driver:
- improved error handling in the probe path
- rejecting an invalid phy-mode specified in the device tree
- register access fix for SJA1105P/Q/R/S for the virtual links through
  the dynamic reconfiguration interface
- handling 2 bridge VLANs where the second is supposed to overwrite the
  first
- making sure that the lack of a pvid results in the actual dropping of
  untagged traffic
====================

Signed-off-by: David S. Miller <davem@davemloft.net>

When running this sequence of operations:

ip link add br0 type bridge vlan_filtering 1
ip link set swp4 master br0
bridge vlan add dev swp4 vid 1

We observe the traffic sent on swp4 is still untagged, even though the
bridge has overwritten the existing VLAN entry:

port    vlan ids
swp4     1 PVID

br0      1 PVID Egress Untagged

This happens because we didn't consider that the 'bridge vlan add'
command just overwrites VLANs like it's nothing. We treat the 'vid 1
pvid untagged' and the 'vid 1' as two separate VLANs, and the first
still has precedence when calling sja1105_build_vlan_table. Obviously
there is a disagreement regarding semantics, and we end up doing
something unexpected from the PoV of the bridge.

Let's actually consider an "existing VLAN" to be one which is on the
same port, and has the same VLAN ID, as one we already have, and update
it if it has different flags than we do.

The first blamed commit is the one introducing the bug, the second one
is the latest on top of which the bugfix still applies.

Fixes: ec5ae610 ("net: dsa: sja1105: save/restore VLANs using a delta commit method")
Fixes: 5899ee36

 ("net: dsa: tag_8021q: add a context structure")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

One thing became visible when writing the blamed commit, and that was
that STP and PTP frames injected by net/dsa/tag_sja1105.c using the
deferred xmit mechanism are always classified to the pvid of the CPU
port, regardless of whatever VLAN there might be in these packets.

So a decision needed to be taken regarding the mechanism through which
we should ensure that delivery of STP and PTP traffic is possible when
we are in a VLAN awareness mode that involves tag_8021q. This is because
tag_8021q is not concerned with managing the pvid of the CPU port, since
as far as tag_8021q is concerned, no traffic should be sent as untagged
from the CPU port. So we end up not actually having a pvid on the CPU
port if we only listen to tag_8021q, and unless we do something about it.

The decision taken at the time was to keep VLAN 1 in the list of
priv->dsa_8021q_vlans, and make it a pvid of the CPU port. This ensures
that STP and PTP frames can always be sent to the outside world.

However there is a problem. If we do the following while we are in
the best_effort_vlan_filtering=true mode:

ip link add br0 type bridge vlan_filtering 1
ip link set swp2 master br0
bridge vlan del dev swp2 vid 1

Then untagged and pvid-tagged frames should be dropped. But we observe
that they aren't, and this is because of the precaution we took that VID
1 is always installed on all ports.

So clearly VLAN 1 is not good for this purpose. What about VLAN 0?
Well, VLAN 0 is managed by the 8021q module, and that module wants to
ensure that 802.1p tagged frames are always received by a port, and are
always transmitted as VLAN-tagged (with VLAN ID 0). Whereas we want our
STP and PTP frames to be untagged if the stack sent them as untagged -
we don't want the driver to just decide out of the blue that it adds
VID 0 to some packets.

So what to do?

Well, there is one other VLAN that is reserved, and that is 4095:
$ ip link add link swp2 name swp2.4095 type vlan id 4095
Error: 8021q: Invalid VLAN id.
$ bridge vlan add dev swp2 vid 4095
Error: bridge: Vlan id is invalid.

After we made this change, VLAN 1 is indeed forwarded and/or dropped
according to the bridge VLAN table, there are no further alterations
done by the sja1105 driver.

Fixes: ec5ae610

 ("net: dsa: sja1105: save/restore VLANs using a delta commit method")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The driver continues probing when a port is configured for an
unsupported PHY interface type, instead it should stop.

Fixes: 8aa9ebcc

 ("net: dsa: Introduce driver for NXP SJA1105 5-port L2 switch")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

If any of sja1105_static_config_load(), sja1105_clocking_setup() or
sja1105_devlink_setup() fails, we can't just return in the middle of
sja1105_setup() or memory will leak. Add a cleanup path.

Fixes: 0a7bdbc2 ("net: dsa: sja1105: move devlink param code to sja1105_devlink.c")
Fixes: 8aa9ebcc

 ("net: dsa: Introduce driver for NXP SJA1105 5-port L2 switch")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Unlike other drivers which pretty much end their .probe() execution with
dsa_register_switch(), the sja1105 does some extra stuff. When that
fails with -ENOMEM, the driver is quick to return that, forgetting to
call dsa_unregister_switch(). Not critical, but a bug nonetheless.

Fixes: 4d752508 ("net: dsa: sja1105: offload the Credit-Based Shaper qdisc")
Fixes: a68578c2

 ("net: dsa: Make deferred_xmit private to sja1105")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

At the beginning of the sja1105_dynamic_config.c file there is a diagram
of the dynamic config interface layout:

 packed_buf

 |
 V
 +-----------------------------------------+------------------+
 |              ENTRY BUFFER               |  COMMAND BUFFER  |
 +-----------------------------------------+------------------+

 <----------------------- packed_size ------------------------>

So in order to pack/unpack the command bits into the buffer,
sja1105_vl_lookup_cmd_packing must first advance the buffer pointer by
the length of the entry. This is similar to what the other *cmd_packing
functions do.

This bug exists because the command packing function for P/Q/R/S was
copied from the E/T generation, and on E/T, the command was actually
embedded within the entry buffer itself.

Fixes: 94f94d4a

 ("net: dsa: sja1105: add static tables for virtual links")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The direction of the pipe argument must match the request-type direction
bit or control requests may fail depending on the host-controller-driver
implementation.

Fix the tiocmset and rfkill requests which erroneously used
usb_rcvctrlpipe().

Fixes: 72dc1c09

 ("HSO: add option hso driver")
Cc: stable@vger.kernel.org      # 2.6.27
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Verify some fields of the USB descriptor to make sure the driver
could be used by the device.

Besides, remove the check of endpoint number in rtl8152_probe().
usb_find_common_endpoints() includes it.

BugLink: https://syzkaller.appspot.com/bug?id=912c9c373656996801b4de61f1e3cb326fe940aa


Reported-by:  <syzbot+95afd23673f5dd295c57@syzkaller.appspotmail.com>
Fixes: c2198943

 ("r8152: search the configuration of vendor mode")
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Reviewed-by: Johan Hovold <johan@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

If Qdisc_ops->init() is failed, Qdisc_ops->reset() would be called.
When dsmark_init(Qdisc_ops->init()) is failed, it possibly doesn't
initialize dsmark_qdisc_data->q. But dsmark_reset(Qdisc_ops->reset())
uses dsmark_qdisc_data->q pointer wihtout any null checking.
So, panic would occur.

Test commands:
    sysctl net.core.default_qdisc=dsmark -w
    ip link add dummy0 type dummy
    ip link add vw0 link dummy0 type virt_wifi
    ip link set vw0 up

Splat looks like:
KASAN: null-ptr-deref in range [0x0000000000000018-0x000000000000001f]
CPU: 3 PID: 684 Comm: ip Not tainted 5.12.0+ #910
RIP: 0010:qdisc_reset+0x2b/0x680
Code: 1f 44 00 00 48 b8 00 00 00 00 00 fc ff df 41 57 41 56 41 55 41 54
55 48 89 fd 48 83 c7 18 53 48 89 fa 48 c1 ea 03 48 83 ec 20 <80> 3c 02
00 0f 85 09 06 00 00 4c 8b 65 18 0f 1f 44 00 00 65 8b 1d
RSP: 0018:ffff88800fda6bf8 EFLAGS: 00010282
RAX: dffffc0000000000 RBX: ffff8880050ed800 RCX: 0000000000000000
RDX: 0000000000000003 RSI: ffffffff99e34100 RDI: 0000000000000018
RBP: 0000000000000000 R08: fffffbfff346b553 R09: fffffbfff346b553
R10: 0000000000000001 R11: fffffbfff346b552 R12: ffffffffc0824940
R13: ffff888109e83800 R14: 00000000ffffffff R15: ffffffffc08249e0
FS:  00007f5042287680(0000) GS:ffff888119800000(0000)
knlGS:0000000000000000
CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 000055ae1f4dbd90 CR3: 0000000006760002 CR4: 00000000003706e0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
Call Trace:
 ? rcu_read_lock_bh_held+0xa0/0xa0
 dsmark_reset+0x3d/0xf0 [sch_dsmark]
 qdisc_reset+0xa9/0x680
 qdisc_destroy+0x84/0x370
 qdisc_create_dflt+0x1fe/0x380
 attach_one_default_qdisc.constprop.41+0xa4/0x180
 dev_activate+0x4d5/0x8c0
 ? __dev_open+0x268/0x390
 __dev_open+0x270/0x390

Fixes: 1da177e4

 ("Linux-2.6.12-rc2")
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The opening comment mark '/**' is used for highlighting the beginning of
kernel-doc comments.
The header for drivers/nfc/nfcmrvl follows this syntax, but the content
inside does not comply with kernel-doc.

This line was probably not meant for kernel-doc parsing, but is parsed
due to the presence of kernel-doc like comment syntax(i.e, '/**'), which
causes unexpected warnings from kernel-doc.
For e.g., running scripts/kernel-doc -none on drivers/nfc/nfcmrvl/spi.c
causes warning:
warning: expecting prototype for Marvell NFC(). Prototype was for SPI_WAIT_HANDSHAKE() instead

Provide a simple fix by replacing such occurrences with general comment
format, i.e. '/*', to prevent kernel-doc from parsing it.

Signed-off-by: Aditya Srivastava <yashsri421@gmail.com>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: David S. Miller <davem@davemloft.net>