DHCP failures were observed with systemd 247.6. The issue could be
reproduced by rebooting Aspeed 2600 and then running ifconfig ethX
down/up.

It is caused by below procedures in the driver:

1. ftgmac100_open() enables net interface and call phy_start()
2. When PHY is link up, it calls netif_carrier_on() and then
adjust_link callback
3. ftgmac100_adjust_link() will schedule the reset task
4. ftgmac100_reset_task() will then reset the MAC in another schedule

After step 2, systemd will be notified to send DHCP discover packet,
while the packet might be corrupted by MAC reset operation in step 4.

Call ftgmac100_reset() directly instead of scheduling task to fix the
issue.

Signed-off-by: Heyi Guo <guoheyi@linux.alibaba.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This is to prepare for ftgmac100_adjust_link() to call
ftgmac100_reset() directly. Only code places are changed.

Signed-off-by: Heyi Guo <guoheyi@linux.alibaba.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This is to prepare for ftgmac100_adjust_link() to call reset function
directly, instead of task schedule.

Signed-off-by: Heyi Guo <guoheyi@linux.alibaba.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Fix following coccicheck warning:
./net/sched/act_api.c:277:7-49: WARNING avoid newline at end of message
in NL_SET_ERR_MSG_MOD

Signed-off-by: Wan Jiabing <wanjiabing@vivo.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Adding myself (Alvin Šipraga) as another maintainer for the Realtek DSA
switch drivers. I intend to help Linus out with reviewing and testing
changes to these drivers, particularly the rtl8365mb driver which I
authored and have hardware access to.

Cc: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Alvin Šipraga <alsi@bang-olufsen.dk>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

These tests are supposed to check if the loop exited via a break or not.
However the tests are wrong because if we did not exit via a break then
"p" is not a valid pointer.  In that case, it's the equivalent of
"if (*(u32 *)sr == *last_key) {".  That's going to work most of the time,
but there is a potential for those to be equal.

Fixes: 1593123a ("tipc: add name table dump to new netlink api")
Fixes: 1a1a143d

 ("tipc: add publication dump to new netlink api")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This test is checking if we exited the list via break or not.  However
if it did not exit via a break then "node" does not point to a valid
udp_tunnel_nic_shared_node struct.  It will work because of the way
the structs are laid out it's the equivalent of
"if (info->shared->udp_tunnel_nic_info != dev)" which will always be
true, but it's not the right way to test.

Fixes: 74cc6d18

 ("udp_tunnel: add the ability to share port tables")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

vhost_vsock_stop() calls vhost_dev_check_owner() to check the device
ownership. It expects current->mm to be valid.

vhost_vsock_stop() is also called by vhost_vsock_dev_release() when
the user has not done close(), so when we are in do_exit(). In this
case current->mm is invalid and we're releasing the device, so we
should clean it anyway.

Let's check the owner only when vhost_vsock_stop() is called
by an ioctl.

When invoked from release we can not fail so we don't check return
code of vhost_vsock_stop(). We need to stop vsock even if it's not
the owner.

Fixes: 433fc58e

 ("VSOCK: Introduce vhost_vsock.ko")
Cc: stable@vger.kernel.org
Reported-by:  <syzbot+1e3ea63db39f2b4440e0@syzkaller.appspotmail.com>
Reported-and-tested-by:  <syzbot+3140b17cb44a7b174008@syzkaller.appspotmail.com>
Signed-off-by: Stefano Garzarella <sgarzare@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

If client is unable to initiate a failover reset via H_VIOCTL hcall, then
it should schedule a failover reset as a last resort. Otherwise, there is
no need to do a last resort.

Fixes: 334c4241

 ("ibmvnic: improve failover sysfs entry")
Reported-by: Cris Forno <cforno12@outlook.com>
Signed-off-by: Sukadev Bhattiprolu <sukadev@linux.ibm.com>
Signed-off-by: Dany Madden <drt@linux.ibm.com>
Link: https://lore.kernel.org/r/20220221210545.115283-1-drt@linux.ibm.com


Signed-off-by: Jakub Kicinski <kuba@kernel.org>

If a bridged port is not offloaded to the hardware - either because the
underlying driver does not implement the port_bridge_{join,leave} ops,
or because the operation failed - then its dp->bridge pointer will be
NULL when dsa_port_bridge_leave() is called. Avoid dereferncing NULL.

This fixes the following splat when removing a port from a bridge:

 Unable to handle kernel access to user memory outside uaccess routines at virtual address 0000000000000000
 Internal error: Oops: 96000004 [#1] PREEMPT_RT SMP
 CPU: 3 PID: 1119 Comm: brctl Tainted: G           O      5.17.0-rc4-rt4 #1
 Call trace:
  dsa_port_bridge_leave+0x8c/0x1e4
  dsa_slave_changeupper+0x40/0x170
  dsa_slave_netdevice_event+0x494/0x4d4
  notifier_call_chain+0x80/0xe0
  raw_notifier_call_chain+0x1c/0x24
  call_netdevice_notifiers_info+0x5c/0xac
  __netdev_upper_dev_unlink+0xa4/0x200
  netdev_upper_dev_unlink+0x38/0x60
  del_nbp+0x1b0/0x300
  br_del_if+0x38/0x114
  add_del_if+0x60/0xa0
  br_ioctl_stub+0x128/0x2dc
  br_ioctl_call+0x68/0xb0
  dev_ifsioc+0x390/0x554
  dev_ioctl+0x128/0x400
  sock_do_ioctl+0xb4/0xf4
  sock_ioctl+0x12c/0x4e0
  __arm64_sys_ioctl+0xa8/0xf0
  invoke_syscall+0x4c/0x110
  el0_svc_common.constprop.0+0x48/0xf0
  do_el0_svc+0x28/0x84
  el0_svc+0x1c/0x50
  el0t_64_sync_handler+0xa8/0xb0
  el0t_64_sync+0x17c/0x180
 Code: f9402f00 f0002261 f9401302 913cc021 (a9401404)
 ---[ end trace 0000000000000000 ]---

Fixes: d3eed0e5

 ("net: dsa: keep the bridge_dev and bridge_num as part of the same structure")
Signed-off-by: Alvin Šipraga <alsi@bang-olufsen.dk>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20220221203539.310690-1-alvin@pqrs.dk


Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Whenever one of these functions pull all data from an skb in a frag_list,
use consume_skb() instead of kfree_skb() to avoid polluting drop
monitoring.

Fixes: 6fa01ccd

 ("skbuff: Add pskb_extract() helper function")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Link: https://lore.kernel.org/r/20220220154052.1308469-1-eric.dumazet@gmail.com


Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Pablo Neira Ayuso says:

====================
Netfilter fixes for net

This is fixing up the use without proper initialization in patch 5/5

-o-

Hi,

The following patchset contains Netfilter fixes for net:

1) Missing #ifdef CONFIG_IP6_NF_IPTABLES in recent xt_socket fix.

2) Fix incorrect flow action array size in nf_tables.

3) Unregister flowtable hooks from netns exit path.

4) Fix missing limit object release, from Florian Westphal.

5) Memleak in nf_tables object update path, also from Florian.
====================

Signed-off-by: David S. Miller <davem@davemloft.net>

stateful objects can be updated from the control plane.
The transaction logic allocates a temporary object for this purpose.

The ->init function was called for this object, so plain kfree() leaks
resources. We must call ->destroy function of the object.

nft_obj_destroy does this, but it also decrements the module refcount,
but the update path doesn't increment it.

To avoid special-casing the update object release, do module_get for
the update case too and release it via nft_obj_destroy().

Fixes: d62d0ba9

 ("netfilter: nf_tables: Introduce stateful object update operation")
Cc: Fernando Fernandez Mancera <ffmancera@riseup.net>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>

We need to provide a destroy callback to release the extra fields.

Fixes: 3b9e2ea6

 ("netfilter: nft_limit: move stateful fields out of expression data")
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>

Unregister flowtable hooks before they are releases via
nf_tables_flowtable_destroy() otherwise hook core reports UAF.

BUG: KASAN: use-after-free in nf_hook_entries_grow+0x5a7/0x700 net/netfilter/core.c:142 net/netfilter/core.c:142
Read of size 4 at addr ffff8880736f7438 by task syz-executor579/3666

CPU: 0 PID: 3666 Comm: syz-executor579 Not tainted 5.16.0-rc5-syzkaller #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Call Trace:
 <TASK>
 __dump_stack lib/dump_stack.c:88 [inline]
 __dump_stack lib/dump_stack.c:88 [inline] lib/dump_stack.c:106
 dump_stack_lvl+0x1dc/0x2d8 lib/dump_stack.c:106 lib/dump_stack.c:106
 print_address_description+0x65/0x380 mm/kasan/report.c:247 mm/kasan/report.c:247
 __kasan_report mm/kasan/report.c:433 [inline]
 __kasan_report mm/kasan/report.c:433 [inline] mm/kasan/report.c:450
 kasan_report+0x19a/0x1f0 mm/kasan/report.c:450 mm/kasan/report.c:450
 nf_hook_entries_grow+0x5a7/0x700 net/netfilter/core.c:142 net/netfilter/core.c:142
 __nf_register_net_hook+0x27e/0x8d0 net/netfilter/core.c:429 net/netfilter/core.c:429
 nf_register_net_hook+0xaa/0x180 net/netfilter/core.c:571 net/netfilter/core.c:571
 nft_register_flowtable_net_hooks+0x3c5/0x730 net/netfilter/nf_tables_api.c:7232 net/netfilter/nf_tables_api.c:7232
 nf_tables_newflowtable+0x2022/0x2cf0 net/netfilter/nf_tables_api.c:7430 net/netfilter/nf_tables_api.c:7430
 nfnetlink_rcv_batch net/netfilter/nfnetlink.c:513 [inline]
 nfnetlink_rcv_skb_batch net/netfilter/nfnetlink.c:634 [inline]
 nfnetlink_rcv_batch net/netfilter/nfnetlink.c:513 [inline] net/netfilter/nfnetlink.c:652
 nfnetlink_rcv_skb_batch net/netfilter/nfnetlink.c:634 [inline] net/netfilter/nfnetlink.c:652
 nfnetlink_rcv+0x10e6/0x2550 net/netfilter/nfnetlink.c:652 net/netfilter/nfnetlink.c:652

__nft_release_hook() calls nft_unregister_flowtable_net_hooks() which
only unregisters the hooks, then after RCU grace period, it is
guaranteed that no packets add new entries to the flowtable (no flow
offload rules and flowtable hooks are reachable from packet path), so it
is safe to call nf_flow_table_free() which cleans up the remaining
entries from the flowtable (both software and hardware) and it unbinds
the flow_block.

Fixes: ff4bf2f4

 ("netfilter: nf_tables: add nft_unregister_flowtable_hook()")
Reported-by:  <syzbot+e918523f77e62790d6d9@syzkaller.appspotmail.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>

Experimentation shows that PHY detect might fail when the code attempts
MDIO bus read immediately after clock enable. Add delay to stabilize the
clock before bus access.

PHY detect failure started to show after commit 7590fc6f ("net:
mdio: Demote probed message to debug print") that removed coincidental
delay between clock enable and bus access.

10ms is meant to match the time it take to send the probed message over
UART at 115200 bps. This might be a far overshoot.

Fixes: 23a890d4

 ("net: mdio: Add the reset function for IPQ MDIO driver")
Signed-off-by: Baruch Siach <baruch.siach@siklu.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

We encounter a tcp drop issue in our cloud environment. Packet GROed in
host forwards to a VM virtio_net nic with net_failover enabled. VM acts
as a IPVS LB with ipip encapsulation. The full path like:
host gro -> vm virtio_net rx -> net_failover rx -> ipvs fullnat
 -> ipip encap -> net_failover tx -> virtio_net tx

When net_failover transmits a ipip pkt (gso_type = 0x0103, which means
SKB_GSO_TCPV4, SKB_GSO_DODGY and SKB_GSO_IPXIP4), there is no gso
did because it supports TSO and GSO_IPXIP4. But network_header points to
inner ip header.

Call Trace:
 tcp4_gso_segment        ------> return NULL
 inet_gso_segment        ------> inner iph, network_header points to
 ipip_gso_segment
 inet_gso_segment        ------> outer iph
 skb_mac_gso_segment

Afterwards virtio_net transmits the pkt, only inner ip header is modified.
And the outer one just keeps unchanged. The pkt will be dropped in remote
host.

Call Trace:
 inet_gso_segment        ------> inner iph, outer iph is skipped
 skb_mac_gso_segment
 __skb_gso_segment
 validate_xmit_skb
 validate_xmit_skb_list
 sch_direct_xmit
 __qdisc_run
 __dev_queue_xmit        ------> virtio_net
 dev_hard_start_xmit
 __dev_queue_xmit        ------> net_failover
 ip_finish_output2
 ip_output
 iptunnel_xmit
 ip_tunnel_xmit
 ipip_tunnel_xmit        ------> ipip
 dev_hard_start_xmit
 __dev_queue_xmit
 ip_finish_output2
 ip_output
 ip_forward
 ip_rcv
 __netif_receive_skb_one_core
 netif_receive_skb_internal
 napi_gro_receive
 receive_buf
 virtnet_poll
 net_rx_action

The root cause of this issue is specific with the rare combination of
SKB_GSO_DODGY and a tunnel device that adds an SKB_GSO_ tunnel option.
SKB_GSO_DODGY is set from external virtio_net. We need to reset network
header when callbacks.gso_segment() returns NULL.

This patch also includes ipv6_gso_segment(), considering SIT, etc.

Fixes: cb32f511

 ("ipip: add GSO/TSO support")
Signed-off-by: Tao Liu <thomas.liu@ucloud.cn>
Reviewed-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Michael Chan says:

====================
bnxt_en: Bug fixes

This series contains bug fixes for FEC reporting, ethtool self test,
multicast setup, devlink health reporting and live patching, and
a firmware response timeout.
====================

Signed-off-by: David S. Miller <davem@davemloft.net>

To install a livepatch, first flash the package to NVM, and then
activate the patch through the "HWRM_FW_LIVEPATCH" fw command.
To uninstall a patch from NVM, flash the removal package and then
activate it through the "HWRM_FW_LIVEPATCH" fw command.

The "HWRM_FW_LIVEPATCH" fw command has to consider following scenarios:

1. no patch in NVM and no patch active. Do nothing.
2. patch in NVM, but not active. Activate the patch currently in NVM.
3. patch is not in NVM, but active. Deactivate the patch.
4. patch in NVM and the patch active. Do nothing.

Fix the code to handle these scenarios during devlink "fw_activate".

To install and activate a live patch:
devlink dev flash pci/0000:c1:00.0 file thor_patch.pkg
devlink -f dev reload pci/0000:c1:00.0 action fw_activate limit no_reset

To remove and deactivate a live patch:
devlink dev flash pci/0000:c1:00.0 file thor_patch_rem.pkg
devlink -f dev reload pci/0000:c1:00.0 action fw_activate limit no_reset

Fixes: 3c415339

 ("bnxt_en: implement firmware live patching")
Reviewed-by: Vikas Gupta <vikas.gupta@broadcom.com>
Reviewed-by: Somnath Kotur <somnath.kotur@broadcom.com>
Signed-off-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When polling for the firmware message response, we first poll for the
response message header.  Once the valid length is detected in the
header, we poll for the valid bit at the end of the message which
signals DMA completion.  Normally, this poll time for DMA completion
is extremely short (0 to a few usec).  But on some devices under some
rare conditions, it can be up to about 20 msec.

Increase this delay to 50 msec and use udelay() for the first 10 usec
for the common case, and usleep_range() beyond that.

Also, change the error message to include the above delay time when
printing the timeout value.

Fixes: 3c8c20db

 ("bnxt_en: move HWRM API implementation into separate file")
Reviewed-by: Vladimir Olovyannikov <vladimir.olovyannikov@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

During ifdown, we call bnxt_inv_fw_health_reg() which will clear
both the status_reliable and resets_reliable flags if these
registers are mapped.  This is correct because a FW reset during
ifdown will clear these register mappings.  If we detect that FW
has gone through reset during the next ifup, we will remap these
registers.

But during normal ifup with no FW reset, we need to restore the
resets_reliable flag otherwise we will not show the reset counter
during devlink diagnose.

Fixes: 8cc95ceb

 ("bnxt_en: improve fw diagnose devlink health messages")
Reviewed-by: Vikas Gupta <vikas.gupta@broadcom.com>
Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Reviewed-by: Somnath Kotur <somnath.kotur@broadcom.com>
Signed-off-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

We should setup multicast only when net_device flags explicitly
has IFF_MULTICAST set. Otherwise we will incorrectly turn it on
even when not asked.  Fix it by only passing the multicast table
to the firmware if IFF_MULTICAST is set.

Fixes: 7d2837dd

 ("bnxt_en: Setup multicast properly after resetting device.")
Signed-off-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In the current code, we setup the port to PHY or MAC loopback mode
and then transmit a test broadcast packet for the loopback test.  This
scheme fails sometime if the port is shared with management firmware
that can also send packets.  The driver may receive the management
firmware's packet and the test will fail when the contents don't
match the test packet.

Change the test packet to use it's own MAC address as the destination
and setup the port to only receive it's own MAC address.  This should
filter out other packets sent by management firmware.

Fixes: 91725d89

 ("bnxt_en: Add PHY loopback to ethtool self-test.")
Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Reviewed-by: Edwin Peer <edwin.peer@broadcom.com>
Reviewed-by: Andy Gospodarek <gospo@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

For offline (destructive) self tests, we need to stop the RDMA driver
first.  Otherwise, the RDMA driver will run into unrecoverable errors
when destructive firmware tests are being performed.

The irq_re_init parameter used in the half close and half open
sequence when preparing the NIC for offline tests should be set to
true because the RDMA driver will free all IRQs before the offline
tests begin.

Fixes: 55fd0cf3

 ("bnxt_en: Add external loopback test to ethtool selftest.")
Reviewed-by: Edwin Peer <edwin.peer@broadcom.com>
Reviewed-by: Ben Li <ben.li@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

ethtool --show-fec <interface> does not show anything when the Active
FEC setting in the chip is set to None.  Fix it to properly return
ETHTOOL_FEC_OFF in that case.

Fixes: 8b277589

 ("bnxt_en: Report FEC settings to ethtool.")
Signed-off-by: Somnath Kotur <somnath.kotur@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

immediate verdict expression needs to allocate one slot in the flow offload
action array, however, immediate data expression does not need to do so.

fwd and dup expression need to allocate one slot, this is missing.

Add a new offload_action interface to report if this expression needs to
allocate one slot in the flow offload action array.

Fixes: be2861dc

 ("netfilter: nft_{fwd,dup}_netdev: add offload support")
Reported-and-tested-by: Nick Gregory <Nick.Gregory@Sophos.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>

If the DSA master doesn't support IFF_UNICAST_FLT, then the following
call path is possible:

dsa_slave_switchdev_event_work
-> dsa_port_host_fdb_add
   -> dev_uc_add
      -> __dev_set_rx_mode
         -> __dev_set_promiscuity

Since the blamed commit, dsa_slave_switchdev_event_work() no longer
holds rtnl_lock(), which triggers the ASSERT_RTNL() from
__dev_set_promiscuity().

Taking rtnl_lock() around dev_uc_add() is impossible, because all the
code paths that call dsa_flush_workqueue() do so from contexts where the
rtnl_mutex is already held - so this would lead to an instant deadlock.

dev_uc_add() in itself doesn't require the rtnl_mutex for protection.
There is this comment in __dev_set_rx_mode() which assumes so:

		/* Unicast addresses changes may only happen under the rtnl,
		 * therefore calling __dev_set_promiscuity here is safe.
		 */

but it is from commit 4417da66 ("[NET]: dev: secondary unicast
address support") dated June 2007, and in the meantime, commit
f1f28aa3 ("netdev: Add addr_list_lock to struct net_device."), dated
July 2008, has added &dev->addr_list_lock to protect this instead of the
global rtnl_mutex.

Nonetheless, __dev_set_promiscuity() does assume rtnl_mutex protection,
but it is the uncommon path of what we typically expect dev_uc_add()
to do. So since only the uncommon path requires rtnl_lock(), just check
ahead of time whether dev_uc_add() would result into a call to
__dev_set_promiscuity(), and handle that condition separately.

DSA already configures the master interface to be promiscuous if the
tagger requires this. We can extend this to also cover the case where
the master doesn't handle dev_uc_add() (doesn't support IFF_UNICAST_FLT),
and on the premise that we'd end up making it promiscuous during
operation anyway, either if a DSA slave has a non-inherited MAC address,
or if the bridge notifies local FDB entries for its own MAC address, the
address of a station learned on a foreign port, etc.

Fixes: 0faf890f

 ("net: dsa: drop rtnl_lock from dsa_slave_switchdev_event_work")
Reported-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Commit b3612ccd ("net: dsa: microchip: implement multi-bridge support")
plugged a packet leak between ports that were members of different bridges.
Unfortunately, this broke another use case, namely that of more than two
ports that are members of the same bridge.

After that commit, when a port is added to a bridge, hardware bridging
between other member ports of that bridge will be cleared, preventing
packet exchange between them.

Fix by ensuring that the Port VLAN Membership bitmap includes any existing
ports in the bridge, not just the port being added.

Fixes: b3612ccd

 ("net: dsa: microchip: implement multi-bridge support")
Signed-off-by: Svenning Sørensen <sss@secomea.com>
Tested-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

All functions defined as static inline in net/checksum.h are
meant to be inlined for performance reason.

But since commit ac7c3e4f ("compiler: enable
CONFIG_OPTIMIZE_INLINING forcibly") the compiler is allowed to
uninline functions when it wants.

Fair enough in the general case, but for tiny performance critical
checksum helpers that's counter-productive.

The problem mainly arises when selecting CONFIG_CC_OPTIMISE_FOR_SIZE,
Those helpers being 'static inline' in header files you suddenly find
them duplicated many times in the resulting vmlinux.

Here is a typical exemple when building powerpc pmac32_defconfig
with CONFIG_CC_OPTIMISE_FOR_SIZE. csum_sub() appears 4 times:

	c04a23cc <csum_sub>:
	c04a23cc:	7c 84 20 f8 	not     r4,r4
	c04a23d0:	7c 63 20 14 	addc    r3,r3,r4
	c04a23d4:	7c 63 01 94 	addze   r3,r3
	c04a23d8:	4e 80 00 20 	blr
		...
	c04a2ce8:	4b ff f6 e5 	bl      c04a23cc <csum_sub>
		...
	c04a2d2c:	4b ff f6 a1 	bl      c04a23cc <csum_sub>
		...
	c04a2d54:	4b ff f6 79 	bl      c04a23cc <csum_sub>
		...
	c04a754c <csum_sub>:
	c04a754c:	7c 84 20 f8 	not     r4,r4
	c04a7550:	7c 63 20 14 	addc    r3,r3,r4
	c04a7554:	7c 63 01 94 	addze   r3,r3
	c04a7558:	4e 80 00 20 	blr
		...
	c04ac930:	4b ff ac 1d 	bl      c04a754c <csum_sub>
		...
	c04ad264:	4b ff a2 e9 	bl      c04a754c <csum_sub>
		...
	c04e3b08 <csum_sub>:
	c04e3b08:	7c 84 20 f8 	not     r4,r4
	c04e3b0c:	7c 63 20 14 	addc    r3,r3,r4
	c04e3b10:	7c 63 01 94 	addze   r3,r3
	c04e3b14:	4e 80 00 20 	blr
		...
	c04e5788:	4b ff e3 81 	bl      c04e3b08 <csum_sub>
		...
	c04e65c8:	4b ff d5 41 	bl      c04e3b08 <csum_sub>
		...
	c0512d34 <csum_sub>:
	c0512d34:	7c 84 20 f8 	not     r4,r4
	c0512d38:	7c 63 20 14 	addc    r3,r3,r4
	c0512d3c:	7c 63 01 94 	addze   r3,r3
	c0512d40:	4e 80 00 20 	blr
		...
	c0512dfc:	4b ff ff 39 	bl      c0512d34 <csum_sub>
		...
	c05138bc:	4b ff f4 79 	bl      c0512d34 <csum_sub>
		...

Restore the expected behaviour by using __always_inline for all
functions defined in net/checksum.h

vmlinux size is even reduced by 256 bytes with this patch:

	   text	   data	    bss	    dec	    hex	filename
	6980022	2515362	 194384	9689768	 93daa8	vmlinux.before
	6979862	2515266	 194384	9689512	 93d9a8	vmlinux.now

Fixes: ac7c3e4f

 ("compiler: enable CONFIG_OPTIMIZE_INLINING forcibly")
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Nick Desaulniers <ndesaulniers@google.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Signed-off-by: David S. Miller <davem@davemloft.net>

Tony Nguyen says:

====================
Intel Wired LAN Driver Updates 2022-02-18

This series contains updates to ice driver only.

Wojciech fixes protocol matching for slow-path switchdev so that all
packets are correctly redirected.

Michal removes accidental unconditional setting of l4 port filtering
flag.

Jake adds locking to protect VF reset and removal to fix various issues
that can be encountered when they race with each other.

Tom Rix propagates an error and initializes a struct to resolve reported
Clang issues.
====================

Signed-off-by: David S. Miller <davem@davemloft.net>

Mat Martineau says:

====================
mptcp: Fix address advertisement races and stabilize tests

Patches 1, 2, and 7 modify two self tests to give consistent, accurate
results by fixing timing issues and accounting for syncookie behavior.

Paches 3-6 fix two races in overlapping address advertisement send and
receive. Associated self tests are updated, including addition of two
MIBs to enable testing and tracking dropped address events.
====================

Signed-off-by: David S. Miller <davem@davemloft.net>

Since commit 2843ff6f ("mptcp: remote addresses fullmesh"), an
MPTCP client can attempt creating multiple MPJ subflow simultaneusly.

In such scenario the server, when syncookies are enabled, could end-up
accepting incoming MPJ syn even above the configured subflow limit, as
the such limit can be enforced in a reliable way only after the subflow
creation. In case of syncookie, only after the 3rd ack reception.

As a consequence the related self-tests case sporadically fails, as it
verify that the server always accept the expected number of MPJ syn.

Address the issues relaxing the MPJ syn number constrain. Note that the
check on the accepted number of MPJ 3rd ack still remains intact.

Fixes: 2843ff6f

 ("mptcp: remote addresses fullmesh")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The in kernel MPTCP PM implementation can process a single
incoming add address option at any given time. In the
mentioned test the server can surpass such limit. Let the
setup cope with that allowing a faster add_addr retransmission.

Fixes: a88c9e49 ("mptcp: do not block subflows creation on errors")
Fixes: f7efc777 ("mptcp: drop argument port from mptcp_pm_announce_addr")
Closes: https://github.com/multipath-tcp/mptcp_net-next/issues/254


Reported-and-tested-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Reviewed-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The MPTCP in kernel path manager has some constraints on incoming
addresses announce processing, so that in edge scenarios it can
end-up dropping (ignoring) some of such announces.

The above is not very limiting in practice since such scenarios are
very uncommon and MPTCP will recover due to ADD_ADDR retransmissions.

This patch adds a few MIB counters to account for such drop events
to allow easier introspection of the critical scenarios.

Fixes: f7efc777

 ("mptcp: drop argument port from mptcp_pm_announce_addr")
Reviewed-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

If an MPTCP endpoint received multiple consecutive incoming
ADD_ADDR options, mptcp_pm_add_addr_received() can overwrite
the current remote address value after the PM lock is released
in mptcp_pm_nl_add_addr_received() and before such address
is echoed.

Fix the issue caching the remote address value a little earlier
and always using the cached value after releasing the PM lock.

Fixes: f7efc777

 ("mptcp: drop argument port from mptcp_pm_announce_addr")
Reviewed-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

After commit a88c9e49 ("mptcp: do not block subflows
creation on errors"), if a signal address races with a failing
subflow creation, the subflow creation failure control path
can trigger the selection of the next address to be announced
while the current announced is still pending.

The above will cause the unintended suppression of the ADD_ADDR
announce.

Fix the issue skipping the to-be-suppressed announce before it
will mark an endpoint as already used. The relevant announce
will be triggered again when the current one will complete.

Fixes: a88c9e49

 ("mptcp: do not block subflows creation on errors")
Reviewed-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The mentioned test has to wait for a subflow creation failure.
The current code looks for TCP sockets in TW state and sometimes
misses the relevant event. Switch to a more stable check, looking
for the associated mib counter.

Fixes: 46e967d1 ("selftests: mptcp: add tests for subflow creation failure")
Closes: https://github.com/multipath-tcp/mptcp_net-next/issues/257


Reported-and-tested-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Instead of waiting for an arbitrary amount of time for the MPTCP
MP_CAPABLE handshake to complete, explicitly wait for the relevant
socket to enter into the established status.

Additionally let the data transfer application use the slowest
transfer mode available (-r), to cope with very slow host, or
high jitter caused by hosting VMs.

Fixes: df62f2ec ("selftests/mptcp: add diag interface tests")
Closes: https://github.com/multipath-tcp/mptcp_net-next/issues/258


Reported-and-tested-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

ida_simple_get() returns an id between min (0) and max (NFP_MAX_MAC_INDEX)
inclusive.
So NFP_MAX_MAC_INDEX (0xff) is a valid id.

In order for the error handling path to work correctly, the 'invalid'
value for 'ida_idx' should not be in the 0..NFP_MAX_MAC_INDEX range,
inclusive.

So set it to -1.

Fixes: 20cce886

 ("nfp: flower: enable MAC address sharing for offloadable devs")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Simon Horman <simon.horman@corigine.com>
Link: https://lore.kernel.org/r/20220218131535.100258-1-simon.horman@corigine.com


Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Switch to the quicinc.com ids.

Signed-off-by: Sean Tranchetti <quic_stranche@quicinc.com>
Signed-off-by: Subash Abhinov Kasiviswanathan <quic_subashab@quicinc.com>
Link: https://lore.kernel.org/r/1645174218-32632-1-git-send-email-quic_subashab@quicinc.com


Signed-off-by: Jakub Kicinski <kuba@kernel.org>