The TBS A711 is a tablet with an A83T, a modem, wifi/BT chip, an eMMC and a
1024x600 LVDS display.

Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

sun4i-a10.dtsi was missing i2s0 block. Add it.

Signed-off-by: Priit Laes <plaes@plaes.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

Add the new DAI blocks to the device tree.

Signed-off-by: Marcus Cooper <codekipper@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

The A83T has an UART1 controller, with the RTS and CTS pins routed so it
can be used for devices with hardware flow control, like a bluetooth chip.

Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

Add the pinctrl definitions for the A83t MMC1 controller.

Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

Those nodes are useless, remove them.

Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

From revision J the board uses new phy chip LAN8710. Compared
with RTL8201, RA17 pin is TXERR. It has pullup which causes phy
not to work. To fix this PA17 is muxed with GMAC function. This
makes the pin output-low.

This patch is compatible with earlier board revisions, since this
pin wasn't connected to phy.

Signed-off-by: Stefan Mavrodiev <stefan@olimex.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

The BT side of the AP6212 WiFi/BT combo module is connected to
uart3.

Enable BT on this board by enabling uart3 with using additionally
the cts and rts pins.

Signed-off-by: Philipp Rossak <embed3d@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

This node adds the definition for the UART3 RTS and CTS Pins

That makes it able to use UART3 with RTS and CTS.

Signed-off-by: Philipp Rossak <embed3d@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

The Nanopi M1 Plus has an onboard IR receiver.
This enables the onboard IR receiver subnode.

Signed-off-by: Philipp Rossak <embed3d@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

The Nanopi M1 has an onboard IR receiver.
This enables the onboard IR receiver subnode.

Signed-off-by: Philipp Rossak <embed3d@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

The axp209.dtsi defines nodes for ac, usb and battery supplies for a
while now. This patch enables these nodes for the A20-Olinuxino-Micro,
which has connectors for all three of them.

The patch was run-tested against linux-next-20170825.

Signed-off-by: Harald Geyer <harald@ccbib.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

A20-OLinuXino-MICRO has option with onboard eMMC chip. For
now it's only shipped with 4BG chip, but in the future this
may change.

Signed-off-by: Stefan Mavrodiev <stefan@olimex.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

Convert sun4i-a10.dtsi to new CCU driver.

Tested on Gemei G9 tablet.

Signed-off-by: Priit Laes <plaes@plaes.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

Convert sun7i-a20.dtsi to new CCU driver.

Tested on Cubietruck.

Signed-off-by: Priit Laes <plaes@plaes.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

When the second display pipeline device nodes for the A31/A31s were
added, it was not known that the TCONs could (through either DRCs)
select either backend as their input. Thus in the endpoints connecting
these components together, the endpoint IDs were set to 0, while in
fact they should have been set to 1.

Cc: <stable@vger.kernel.org>
Fixes: 9a26882a ("ARM: dts: sun6i: Add second display pipeline device
		      nodes")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

In order to maximize the use of MSI, a PCIe controller will share
all MSI controllers. The patch changes msi-parent to refer to all
MSI controller dts nodes.

Signed-off-by: Minghuan Lian <Minghuan.Lian@nxp.com>
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>

"1" should be replaced by "l". This is a typo.
The patch is to fix it.

Signed-off-by: Minghuan Lian <Minghuan.Lian@nxp.com>
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>

AT91SAM9G45 has an AC97 controller, but it is not described in the dts
file.
This patch adds AC97 node in device tree.

Signed-off-by: Dmitry Rezvanov <dmitry.rezvanov@yandex.ru>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>

Add pinctrl groups of ethenet phy mode, such as "ether_rgmii", "ether_rmii",
and "ether_mii".

Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>

All registers are located within 0x400 size from the base address.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>

Add UniPhier AIDET (ARM Interrupt Detector) nodes to support
active low interrupts.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>

Since the discussion is not settled yet for the EMAC, and that the release
in getting really close, let's revert the changes for now, and we'll
reintroduce them later.

Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

This reverts commit ddb56254. The EMAC
bindings have not stabilized yet, so we can't commit to keeping them
stable.

Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

This patch solves the following error:
arch/arm/boot/dts/rk3228-evb.dtb: ERROR (phandle_references): Reference to non-existent node or label "phy0"

Fixess db40f15b ("ARM: dts: rk3228-evb: Enable the integrated PHY for gmac")
Signed-off-by: David Wu <david.wu@rock-chips.com>
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add the as3645a flash controller to the DT source.

Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>

CEC support was added for Exynos5 in 4.13, but for the Odroids we need to set
'needs-hpd' as well since CEC is disabled when there is no HDMI hotplug signal,
just as for the exynos4 Odroid-U3.

This is due to the level-shifter that is disabled when there is no HPD, thus
blocking the CEC signal as well. Same close-but-no-cigar board design as the
Odroid-U3.

Tested with my Odroid XU4.

Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>

Rockchip's rv1108-evb board has one usb otg controller and one usb
host controller, each usb controller connect with one usb-phy port
through UTMI+ interface. This patch enables them to support usb on
rv1108-evb board.

Signed-off-by: Frank Wang <frank.wang@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>

This patch adds usb otg/host controllers and phys nodes for RV1108 SoCs.

Signed-off-by: Frank Wang <frank.wang@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>

The window of the Aspeed AST2400 SMC Controllers to map chips on the
AHB Bus has a 256MB size. The full window range is

    [ 0x20000000 - 0x2FFFFFFF ] for the FMC controller
    [ 0x30000000 - 0x3FFFFFFF ] for the SPI controller

This change requires CONFIG_VMSPLIT_2G to be set.

Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Joel Stanley <joel@jms.id.au>

The cpu is powered by regulator vdd_core on RV1108 evalution
board. Add it to the cpu dt node.

Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>

Add cpu opp table for rv1108 to support frequency
from 408MHZ to 1008MHZ.

Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>

This adds the operating points to the Ux500 device tree and
deletes the old special-purpose cpufreq node, as we can now
use the generic DT cpufreq driver.

Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>

Add VPU/VDEC/VOP/IEP iommu nodes

Signed-off-by: Simon Xue <xxm@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>

Earlyconsole is used for early kernel debugging that's why this option
shouldn't be enabled by default.
Earlyconsole is partially copying the part of the bootlog after
"bootconsole [uart0] disabled".

Signed-off-by: Michal Simek <michal.simek@xilinx.com>

Change the dtsi include code to use the C pre-processor #include instead
of the device tree /include/. This brings all Zynq device trees inline
with each other.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>

This will simplify dt overlay structure for the whole PL.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>

Mention device-type = "ethernet-phy", as qemu will need this in absence
of compatible.

Signed-off-by: Sai Pavan Boddu <saipava@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>

Describe adv7511 on i2c bus.

Signed-off-by: Christian Kohn <christian.kohn@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>

This adds a new node for the LEGO MINDSTORMS EV3 LCD display.

Signed-off-by: David Lechner <david@lechnology.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>