The Banana Pi is an A20 based development board using Raspberry Pi compatible
IO headers. It comes with 1 GB RAM, 1 Gb ethernet, 2x USB host, sata, hdmi
and stereo audio out + various expenansion headers:

http://www.lemaker.org/



Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

The uart3_pins_a multiplexes the uart3 pins to port G, add a pinctrl entry
for mapping them to port H (as used on the Bananapi).

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

The dma controller requires that the ahb1 bus clock be driven by pll6
for peripheral access to work. Previously this was done in the dma
controller driver, but was since removed as part of a series to unify
the ahb1_mux and ahb1 clock drivers, in

    14e0e283 dmaengine: sun6i: Remove obsolete clk muxing code

Unfortunately the rest of that series did not make it, leaving us with
broken dma on sun6i.

This patch reparents ahb1_mux to pll6 using the DT assigned-clocks
properties in the dma controller node.

Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

Explicitly set the dr_mode for the second dwc3 controller on the
Arndale Octa board to host mode. This is required to ensure the
controller is initialized in the right mode if the kernel is build
with USB gadget support.

Reported-By: Andreas Faerber <afaerber@suse.de>
Signed-off-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>

In case the optional dr_mode property isn't set in the dwc3 nodes the
the controller will go into OTG mode if both USB host and USB gadget
functionality are enabled in the kernel configuration. Unfortunately
this results in USB not working on exynos5420-peach-pit and
exynos5800-peach-pi with such a kernel configuration unless manually
change the mode. To resolve that explicitly configure the dual role
mode as host.

Signed-off-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Reviewed-by: Andreas Faerber <afaerber@suse.de>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>

CM-QS600 is a APQ8064 based computer on module.
The details are available at
http://compulab.co.il/products/computer-on-modules/cm-qs600/



Signed-off-by: Mike Rapoport <mike.rapoport@gmail.com>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Kumar Gala <galak@codeaurora.org>

This DTS has support for the Sony Xperia Z1 phone (codenamed Honami).
This first version of the DTS supports just a serial console.

Signed-off-by: Tim Bird <tim.bird@sonymobile.com>
Tested-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Kumar Gala <galak@codeaurora.org>

Add SATA PHY and SATA AHCI controller nodes to device tree to enable
generic ahci support on the IPQ8064/AP148 board.

Signed-off-by: Kumar Gala <galak@codeaurora.org>

Fix wrong compatible string of Exynos3250 RTC (Real-Time Clock) dt node.
The RTC of Exynos3250 must need additional source clock (XrtcXTI).

Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

I added smc91x support but turns out we currently do not set the
smc91x timings in gpmc.c but rely on the bootloader timings. This
produces the following error unless the smc91x GPMC timings are
initialized by the bootloader:

Unhandled fault: external abort on non-linefetch (0x1008) at 0xd080630e
...
[<c04067fc>] (smc_drv_probe) from [<c038e9c4>] (platform_drv_probe+0x2c/0x5c)
[<c038e9c4>] (platform_drv_probe) from [<c038d450>] (driver_probe_device+0x104/0x22c)
[<c038d450>] (driver_probe_device) from [<c038d60c>] (__driver_attach+0x94/0x98)
[<c038d60c>] (__driver_attach) from [<c038bc3c>] (bus_for_each_dev+0x54/0x88)
[<c038bc3c>] (bus_for_each_dev) from [<c038cc3c>] (bus_add_driver+0xd8/0x1d8)
[<c038cc3c>] (bus_add_driver) from [<c038dd74>] (driver_register+0x78/0xf4)
[<c038dd74>] (driver_register) from [<c0008924>] (do_one_initcall+0x80/0x1c0)
[<c0008924>] (do_one_initcall) from [<c0852d9c>] (kernel_init_freeable+0x1b8/0x28c)
[<c0852d9c>] (kernel_init_freeable) from [<c05ce86c>] (kernel_init+0x8/0xec)
[<c05ce86c>] (kernel_init) from [<c000e728>] (ret_from_fork+0x14/0x2c)

Let's fix the issue by disabling the smc91x module for now until we
have sorted out the issues in gpmc.c.

Reported-by: Kevin Hilman <khilman@linaro.org>
Tested-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Regulators for MMC2 (SD card) are PVDD_TFLASH_2V8 (LDO19) for vmmc
and PVDD_APIO_MMCOFF_2V8 (LDO13) for vqmmc.  Currently the device
tree entry for MMC2 uses PVDD_PRE_1V8 (LDO10) for vmmc and vqmmc is
not specified.  Fix it.

Without this patch:
- "mmc: dw_mmc: use mmc_regulator_get_supply to handle regulators"
  patch causes a SD card detection to fail
- "mmc: dw_mmc: Support voltage changes" patch causes a boot hang

This patch fixes both above problems.

Suggested-by: Doug Anderson <dianders@google.com>
Cc: Yuvaraj Kumar C D <yuvaraj.cd@samsung.com>
Cc: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Fixes: 01730558 ("mmc: dw_mmc: Support voltage changes")
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Carlo Caione <carlo@caione.org>

The K2L MDIO io space has different start address.
Hence, fix it to be 0x26200f00 according to TRM.

Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>

The K2E MDIO io space has different start address.
Hence, fix it to be 0x24200f00 according to TRM.

Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>

Keystone supports dma-coherent on USB master and also needs
dma-ranges to specify the hardware alias memory range in which DMA
can be operational.
Such configuration applied for USB0 devices, but It's missed for
USB1 device which is present only in K2E SoC - hence apply it.

Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>

The IO range size is set incorrectly for USB PHY0 deivice
it should be 24 instead of 32. Otherwise, It causes
USB PHY1 probing failure.

Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>

This patch enables the Ethernet port on the Marvell Berlin2Q DMP board.

Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch adds the Ethernet node, enabling the network unit on Berlin
BG2Q SoCs.

Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add the clock tree description for the PXA27x based boards.

Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Mike Turquette <mturquette@linaro.org>

There are 2 MACIDs stored in the control module of the am33xx. These are
read by the cpsw driver if no valid MACID was found in the devicetree.

Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Reviewed-by: Wolfram Sang <wsa@the-dreams.de>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Reviewed-by: Wolfram Sang <wsa@the-dreams.de>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Now that we have a compatible of its own for the mbus clock, switch to it.

Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>

Enable gcov support for ARM based on original patches by David
Singleton and George G. Davis

Riku - updated to patch to current mainline kernel. The patch
has been submitted in 2010, 2012 - for symmetry, now in 2014 too.

https://lwn.net/Articles/390419/
http://marc.info/?l=linux-arm-kernel&m=133823081813044



v2: remove arch/arm/kernel from gcov disabled files

Cc: Andrey Ryabinin <a.ryabinin@samsung.com>
Cc: Naresh Kamboju <naresh.kamboju@linaro.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Riku Voipio <riku.voipio@linaro.org>
Signed-off-by: Vincent Sanders <vincent.sanders@collabora.co.uk>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Apparently most of the newly added nodes had the same problem,
so instead of reverting the individual patches, this undoes
the effect of the merge and backs out all of them at once.

Signed-off-by: Arnd Bergmann <arnd@arndb.de>

This reverts commit 610bd872.

"ARM: dts: hix5hd2: add wdg node" causes a build breakage due to
an undefined constatns:

Error: arch/arm/boot/dts/hisi-x5hd2.dtsi:374.22-23 syntax error

(Don't you just looove the dtc error messages? They are so informative!)

Signed-off-by: Olof Johansson <olof@lixom.net>

Add dt for rk3288 i2s controller, since i2s clock pins and data pins
default to be GPIO, this patch also add pinctrl to mux them.

Tested on RK3288 board.

Signed-off-by: Jianqun Xu <jay.xu@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>

... for V2M-P1 motherboard CLCD (limited to 640x480 16bpp and using
dedicated video RAM bank) and for V2P-CA9 (up to 1024x768 16bpp).

Signed-off-by: Pawel Moll <pawel.moll@arm.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>

Signed-off-by: Florian Meier <florian.meier@koalo.de>
[Tweaked slightly to disable by default -- broonie]
Signed-off-by: Mark Brown <broonie@linaro.org>
[swarren, removed duplicate i2s node]
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>

The Meson6 SoC is produced by Amlogic inc. and it is based on 2 Cortex
A9 and an ARM Mali-400 GPU.
This patch adds two basic DTSI for the preliminary support of Meson and
Meson6 SoCs. Another DTS is also added for supporting the atv1200 board,
produced by Geniatech inc.

Signed-off-by: Carlo Caione <carlo@caione.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>

With the introduction of DT based idle states, CPUidle drivers for ARM
can now initialize idle states data through properties in the device tree.

This patch adds code to the big.LITTLE CPUidle driver to dynamically
initialize idle states data through the updated device tree source file.

Cc: Chander Kashyap <k.chander@samsung.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>

This patch changes the compatible string of the GIC to the
new "arm,cortex-a7-gic" which does reflect the actual hardware.

Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Signed-off-by: Olof Johansson <olof@lixom.net>

Add the missing 'compatible' property to device tree root node of

 - mt6589-aquaris5.dts

and document the new values.

Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Signed-off-by: Olof Johansson <olof@lixom.net>

Add boot argument for earlyprintk to the aquaris5 device tree file.

Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Signed-off-by: Olof Johansson <olof@lixom.net>

This changes the unit address of the gic node to it's first register area.

Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Signed-off-by: Olof Johansson <olof@lixom.net>

This allows the "make dtbs" to build the aquaris5 dtb for the Mediatek
SoC.

Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Signed-off-by: Olof Johansson <olof@lixom.net>

As discovered on a custom board similar to at91sam9263ek and basing
its devicetree on that one apparently the pin muxing doesn't get
set up properly. This was discovered since the custom boards u-boot
does funky stuff with the pin muxing and leaved it set to SPI
which made the MMC driver not work under Linux.
The fix is simply to define the given configuration as the default.
This probably worked by pure luck before, but it's better to
make the muxing explicitly set.

Signed-off-by: Andreas Henriksson <andreas.henriksson@endian.se>
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: <stable@vger.kernel.org>  # 3.11+

The group has the samsung,pin-pud property set to 4, which is not a
correct value. This patch fixes this by replacing it with 3, which is
the correct value for pull-up.

Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>

PCIe configuration space should be passed through reg property, rather than
through ranges property.  This patch does the correction for SPEAr13XX
SOCs.

Signed-off-by: Pratyush Anand <pratyush.anand@st.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Mohit Kumar <mohit.kumar@st.com>

Fix incorrect clock names for usb1, pcie1 and domain register
offset for pcie1 clock nodes on K2E EVM

Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>